MACSec test failed when asynchronous crypto operations is used. It
encounters packet validation failed since macsec_skb_cb(skb)->valid
is always 'false'.

This patch adds missing "macsec_skb_cb(skb)->valid = true" in
macsec_decrypt_done() when "err == 0".
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The USEC_PER_SEC is used once in sock_set_timeout as the max value of
tv_usec. But there are other similar codes which use the literal
1000000 in this file.
It is minor cleanup to keep consitent.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch switch to use build_skb() for small buffer which can have
better performance for both TCP and XDP (since we can work at page
before skb creation). It also remove lots of XDP codes since both
mergeable and small buffer use page frag during refill now.

                       Before   | After
XDP_DROP(xdp1) 64B  :  11.1Mpps | 14.4Mpps

Tested with xdp1/xdp2/xdp_ip_tx_tunnel and netperf.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The skbs processed by ip_cmsg_recv() are not guaranteed to
be linear e.g. when sending UDP packets over loopback with
MSGMORE.
Using csum_partial() on [potentially] the whole skb len
is dangerous; instead be on the safe side and use skb_checksum().

Thanks to syzkaller team to detect the issue and provide the
reproducer.

v1 -> v2:
 - move the variable declaration in a tighter scope

Fixes: ad6f939a ("ip: Add offset parameter to ip_cmsg_recv")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

silences the below warning:
    drivers/net/vxlan.c: In function ‘neigh_reduce’:
    drivers/net/vxlan.c:1599:25: warning: variable ‘saddr’ set but not used
    [-Wunused-but-set-variable]
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds changelink rtnl op support for vxlan netdevs.
code changes involve:
    - refactor vxlan_newlink into vxlan_nl2conf to be
    used by vxlan_newlink and vxlan_changelink
    - vxlan_nl2conf and vxlan_dev_configure take a
    changelink argument to isolate changelink checks
    and updates.
    - Allow changing only a few attributes:
        - return -EOPNOTSUPP for attributes that cannot
        be changed for now. Incremental patches can
        make the non-supported one available in the future
        if needed.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is only one possible error path which reaches the err label, so
return ERR_PTR(-ENOMEM) directly if alloc_netdev_mqs() fails. This also
allows to omit the err variable.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

We set queues before reset which will cause a crash[1]. This is
because is_xdp_raw_buffer_queue() depends on the old xdp queue pairs
number to do the correct detection. So fix this by

- passing xdp queue pairs and current queue pairs to virtnet_reset()
- change vi->xdp_qp after reset but before refill, to make sure both
  free_unused_bufs() and refill can make correct detection of XDP.
- remove the duplicated queue pairs setting before virtnet_reset()
  since we will do it inside virtnet_reset()

[1]

[   74.328168] general protection fault: 0000 [#1] SMP
[   74.328625] Modules linked in: nfsd xfs libcrc32c virtio_net virtio_pci
[   74.329117] CPU: 0 PID: 2849 Comm: xdp2 Not tainted 4.10.0-rc7+ #499
[   74.329577] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.10.1-0-g8891697-prebuilt.qemu-project.org 04/01/2014
[   74.330424] task: ffff88007a894000 task.stack: ffffc90004388000
[   74.330844] RIP: 0010:skb_release_head_state+0x28/0x80
[   74.331298] RSP: 0018:ffffc9000438b8d0 EFLAGS: 00010206
[   74.331676] RAX: 0000000000000000 RBX: ffff88007ad96300 RCX: 0000000000000000
[   74.332217] RDX: ffff88007fc137a8 RSI: ffff88007fc0db28 RDI: 0001bf00000001be
[   74.332758] RBP: ffffc9000438b8d8 R08: 000000000005008f R09: 00000000000005f9
[   74.333274] R10: ffff88007d001700 R11: ffffffff820a8a4d R12: ffff88007ad96300
[   74.333787] R13: 0000000000000002 R14: ffff880036604000 R15: 000077ff80000000
[   74.334308] FS:  00007fc70d8a7b40(0000) GS:ffff88007fc00000(0000) knlGS:0000000000000000
[   74.334891] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   74.335314] CR2: 00007fff4144a710 CR3: 000000007ab56000 CR4: 00000000003406f0
[   74.335830] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[   74.336373] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[   74.336895] Call Trace:
[   74.337086]  skb_release_all+0xd/0x30
[   74.337356]  consume_skb+0x2c/0x90
[   74.337607]  free_unused_bufs+0x1ff/0x270 [virtio_net]
[   74.337988]  ? vp_synchronize_vectors+0x3b/0x60 [virtio_pci]
[   74.338398]  virtnet_xdp+0x21e/0x440 [virtio_net]
[   74.338741]  dev_change_xdp_fd+0x101/0x140
[   74.339048]  do_setlink+0xcf4/0xd20
[   74.339304]  ? symcmp+0xf/0x20
[   74.339529]  ? mls_level_isvalid+0x52/0x60
[   74.339828]  ? mls_range_isvalid+0x43/0x50
[   74.340135]  ? nla_parse+0xa0/0x100
[   74.340400]  rtnl_setlink+0xd4/0x120
[   74.340664]  ? cpumask_next_and+0x30/0x50
[   74.340966]  rtnetlink_rcv_msg+0x7f/0x1f0
[   74.341259]  ? sock_has_perm+0x59/0x60
[   74.341586]  ? napi_consume_skb+0xe2/0x100
[   74.342010]  ? rtnl_newlink+0x890/0x890
[   74.342435]  netlink_rcv_skb+0x92/0xb0
[   74.342846]  rtnetlink_rcv+0x23/0x30
[   74.343277]  netlink_unicast+0x162/0x210
[   74.343677]  netlink_sendmsg+0x2db/0x390
[   74.343968]  sock_sendmsg+0x33/0x40
[   74.344233]  SYSC_sendto+0xee/0x160
[   74.344482]  ? SYSC_bind+0xb0/0xe0
[   74.344806]  ? sock_alloc_file+0x92/0x110
[   74.345106]  ? fd_install+0x20/0x30
[   74.345360]  ? sock_map_fd+0x3f/0x60
[   74.345586]  SyS_sendto+0x9/0x10
[   74.345790]  entry_SYSCALL_64_fastpath+0x1a/0xa9
[   74.346086] RIP: 0033:0x7fc70d1b8f6d
[   74.346312] RSP: 002b:00007fff4144a708 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
[   74.346785] RAX: ffffffffffffffda RBX: 00000000ffffffff RCX: 00007fc70d1b8f6d
[   74.347244] RDX: 000000000000002c RSI: 00007fff4144a720 RDI: 0000000000000003
[   74.347683] RBP: 0000000000000003 R08: 0000000000000000 R09: 0000000000000000
[   74.348544] R10: 0000000000000000 R11: 0000000000000246 R12: 00007fff4144bd90
[   74.349082] R13: 0000000000000002 R14: 0000000000000002 R15: 00007fff4144cda0
[   74.349607] Code: 00 00 00 55 48 89 e5 53 48 89 fb 48 8b 7f 58 48 85 ff 74 0e 40 f6 c7 01 74 3d 48 c7 43 58 00 00 00 00 48 8b 7b 68 48 85 ff 74 05 <f0> ff 0f 74 20 48 8b 43 60 48 85 c0 74 14 65 8b 15 f3 ab 8d 7e
[   74.351008] RIP: skb_release_head_state+0x28/0x80 RSP: ffffc9000438b8d0
[   74.351625] ---[ end trace fe6e19fd11cfc80b ]---

Fixes: 2de2f7f4 ("virtio_net: XDP support for adjust_head")
Cc: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This commit adds the ndo_do_ioctl() callback which allows the userspace to
access PHY registers, for example. This will make mii-diag and similar
tools work.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.

As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michael Chan says:

====================
bnxt_en: Fix probe and open bugs.

Fix 3 issues related to bnxt_init_one() and bnxt_open().  Don't probe
bridge devices and fixup some error code paths.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

In the bnxt_init_one() failure path, bar1 and bar2 are not
being unmapped.  This commit fixes this issue.  Reorganize the
code so that bnxt_init_one()'s failure path and bnxt_remove_one()
can call the same function to do the PCI cleanup.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If bnxt_hwrm_ring_free() is called during a failure path in bnxt_open(),
it is possible that the completion rings have not been allocated yet.
In that case, the completion doorbell has not been initialized, and
calling bnxt_disable_int() will crash.  Fix it by checking that the
completion ring has been initialized before writing to the completion
ring doorbell.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are additional SoC devices that use the same device ID for
bridge and NIC devices.  The bnxt driver should reject probe against
all bridge devices since it's meant to be used with only endpoint
devices.
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Yuval Mintz says:

====================
qed*: Bug fixes

This is a respin of the series with same name for net-next
instead of net [only patch #10 is changed].

The 3 first patches here are a repost of
("qed: RoCE infrastructure fixes"). The fourth is an additional
RoCE-related infrastructure fix, and the latter contain various fixes
to qed/qede.

Please consider applying these to `net-next'.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Driver changes the link properties via communication with
the management firmware, and re-reads the resulting link status
when it receives an indication that the link has changed.
However, there are certain scenarios where such indications
might be missing, and so driver also re-reads the current link
results without attention in several places. Specifically, it
does so during load and when resetting the link.

This creates a race where driver might reflect incorrect
link status - e.g., when explicit reading of the link status is
switched by attention with the changed configuration.

Correct this flow by a lock syncronizing the handling of the
link indications [both explicit requests and attention].
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Flows accessing registers require the flow to hold a PTT entry.
To protect 'major' load/unload flows a main_ptt is pre-allocated
to guarantee such flows wouldn't be blocked by PTT being
unavailable.

Status block initialization currently uses the main_ptt which
is incorrect, as this flow might run concurrently to others
[E.g., loading qedr while toggling qede]. That would have dire
effects as it means registers' access to device breaks and further
read/writes might access incorrect addresses.

Instead, when initializing status blocks acquire/release a PTT
as part of the flow.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Driver currently utilizes the same loop variable in two
nested loops.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

VF learns of the current link state via its bulletin board,
which might reflect either the physical link state or some
user-configured logical state.
Whenever the physical link changes or whnever such a configuration
is explicitly made by user the PF driver would update the bulletin
that the VF reads. But if neither has happened - i.e., PF still
hasn't got a physical link up and no additional configuration was
done the VF wouldn't have a valid link information available.

Simply reflect the physical link state whenever the VF is
initialized. The user could then affect it however he wants.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed needs to be informed of the removal of the qede interface
prior to its actual removal, as qede has some registered callbacks
that might get called async to the removal flow.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Need to make sure the slowpath workqueue and the qede lock
are ready for the registration of the netdevice, as once
registered there's no guarantee those wouldn't be used.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Reserving doorbell BAR space according to the currently active CPUs
may result in a bug if disabled CPUs are later enabled but no
doorbell space was reserved for them.
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If QP is in reset state then there are no resources to free so avoid
freeing any.
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently the state is read only after the buffers are relesed.
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The CQ resource pool is protected by a spin lock. When a CQ creation
fails it now deallocates under that lock as well.
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pavel Belous says:

====================
net: ethernet: aquantia: improvements and fixes

The following patchset contains improvements and fixes for aQuantia
AQtion ethernet driver from net-next tree.

Most fixes are based on the comments from Lino Sanfilippo.

Sanity testing was performed on real HW. No regression found.

v1->v2: 1)Removed buffers copying.
	2)Fixed dma error handling.

v2->v3: 1)Fixes for aq_ndev_change_mtu:
	-Use core MTU checking for min_mtu.
	-Removed extra new_mtu assigment.
	2)Reverse XMAS tree in aq_ring_rx_fill.
v3->v4: 1)Use ndev->reg_state instead "is_ndev_registered" flag.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This fix removes copying of tx biffers.
Now we use ring->buff_fing directly.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We should allocate the number of pages based on the config parameter
AQ_CFG_RX_FRAME_MAX.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rxd_wb->pkt_len is the total length of the packet.
If we received a large packet (with length > AQ_CFG_RX_FRAME_MAX) then we
will get multiple buffers. We need to fix the length of the last buffer.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netdev_register should be called when everything is initialized.
Also we should use net_device->reg_state field instead own
"is_ndev_registered" flag to avoid any race.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We should check for a null pointer for aq_nic_ndev_alloc
instead netdev_priv.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Reviewed-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use NETDEV_TX_OK as the return value for successful transmission.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Reviewed-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

rtnl_unlock should be called if error occurred.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Reviewed-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixed superfluous initialization of err.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Reviewed-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove boilerplate code by using macro module_pci_driver.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Reviewed-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

1)Removed unnecessary comparsion "old_mtu == new_mtu".
This check is not needed. Function aq_ndev_change_mtu wont be called
if mtu has not changed.

2)Removed extra assignment ndev->mtu = new_mtu;
This assignment already done inside __dev_set_mtu().

3)Use core MTU checking for min_mtu.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

 busy_count field and is_busy flag is not needed at all.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Reviewed-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

This assignment is not needed.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Reviewed-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.

As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.

As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>