In K2G, the clock handling is done through firmware executing on a
separate core. Linux kernel needs to communicate to the firmware
through TI system control interface to access any power management
related resources, including clocks.

The keystone sci-clk driver does this, by communicating to the
firmware through the TI SCI driver. The driver adds support for
registering clocks through DT, and basic required clock operations
like prepare/get_rate, etc.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
[sboyd@codeaurora.org: Make ti_sci_init_clocks() static]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

Add a clock implementation, TI SCI clock, that will hook to the common
clock framework, and allow each clock to be controlled via TI SCI
protocol.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

Commit ad149724 ("clk: imx7d: Fix the powerdown bit location
of PLL DDR") used the incorrect bit for the IMX_PLLV3_DDR_IMX7 case.

Fix it accordingly to avoid a kernel hang.
Reported-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

Fix missing }
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

The old RealView clock implementation is not used anymore
(nothing in the kernel calls realview_clk_init()) as we have
moved all clocks over to device tree. Delete it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

Fractional clock dividers generate accurate average frequencies but
with jitter, particularly when the integer divisor is small.

Introduce a new metric of clock accuracy to penalise clocks with a good
average but worse jitter compared to clocks with an average which is no
better but with lower jitter. The metric is the ideal rate minus the
worse deviation from that ideal using the nearest integer divisors.

Use this metric for parent selection for clocks requiring low jitter
(currently just PCM).
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

Restrict clock sources for the PCM peripheral to the oscillator and
PLLD_PER because other source may have varying rates or be switched off.
Prevent other sources from being selected by replacing their names in
the list of potential parents with dummy entries (entry index is
significant).
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

If a clock has the prediv flag set, both the integer and fractional
parts must be scaled when calculating the resulting frequency.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

* clk-bulk-get:
  clk: add managed version of clk_bulk_get
  clk: add clk_bulk_get accessories

This patch introduces the managed version of clk_bulk_get.

Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Anson Huang <anson.huang@nxp.com>
Cc: Robin Gong <yibin.gong@nxp.com>
Cc: Bai Ping <ping.bai@nxp.com>
Cc: Leonard Crestez <leonard.crestez@nxp.com>
Cc: Octavian Purdila <octavian.purdila@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

These helper function allows drivers to get several clk consumers in
one operation. If any of the clk cannot be acquired then any clks
that were got will be put before returning to the caller.

This can relieve the driver owners' life who needs to handle many clocks,
as well as each clock error reporting.

Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Anson Huang <anson.huang@nxp.com>
Cc: Robin Gong <yibin.gong@nxp.com>
Cc: Bai Ping <ping.bai@nxp.com>
Cc: Leonard Crestez <leonard.crestez@nxp.com>
Cc: Octavian Purdila <octavian.purdila@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

These can be marked as const * const.

Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

Pull Amlogic clock driver updates from Jerome Brunet:

 * Expose more i2s and spdif output clocks
 * Expose EE uart and SPICC gate clocks
 * Remove cpu_clk from to gxbb
 * Mark clk81 as critical on gxbb
 * Add CEC EE clocks

* tag 'meson-clk-for-4.13' of git://github.com/BayLibre/clk-meson:
  clk: meson-gxbb: Add EE 32K Clock for CEC
  clk: gxbb: remove CLK_IGNORE_UNUSED from clk81
  clk: meson: meson8b: mark clk81 as critical
  clk: meson: gxbb: remove the "cpu_clk" from the GXBB and GXL driver
  clk: meson-gxbb: un-export the CPU clock
  clk: meson-gxbb: expose UART clocks
  clk: meson-gxbb: expose SPICC gate
  clk: meson-gxbb: expose spdif master clock
  clk: meson-gxbb: expose i2s master clock
  clk: meson-gxbb: expose spdif clock gates

Undo preparation of a clock source, if palmas_clks_init_configure is not
successful.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

When CONFIG_ON=n, dummies are provided for of_clk_get() and
of_clk_get_by_name(), but not for of_clk_get_from_provider().

Provide a dummy for the latter, to improve the ability to do
compile-testing.  This requires removing the existing dummy in the
Lantiq clock code.

Fixes: 766e6a4e ("clk: add DT clock binding support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Thomas Langer <thomas.langer@intel.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

Merge tag 'clk-renesas-for-v4.13-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into clk-next

clk: renesas: Updates for v4.13

  - Add more module clocks for R-Car H3 ES2.0 and M3-W,
  - Add CPG/MSSR drivers for all supported R-Car Gen2 SoCs, enabling support
    for module resets, which are not supported by the existing driver,
  - Rework Kconfig and Makefile logic,
  - Small fixes and cleanups.

When failing to set a clock the printout emitted is incorrect.
"u32 rate" is formatted as %d and should be %u whereas "unsigned long
clk_set_rate()" is formatted as %ld and should be %lu as per
Documentation/printk-formats.txt.

Fixes: 2885c3b2 ("clk: Show correct information when fail to set clock rate")
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

The frequencies above the maximum value of signed integer(i.e. 2^31 -1)
will overflow with the current code.

This patch fixes the return type of __scpi_dvfs_round_rate from 'int'
to 'unsigned long'.

Fixes: cd52c2a4 ("clk: add support for clocks provided by SCP(System Control Processor)")
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

ls1012a has separate input root clocks for core PLLs versus the
platform PLL, with the latter described as sysclk in the hw docs.
If a second input clock, named "coreclk", is present, this clock will be
used for the core PLLs.
Signed-off-by: Scott Wood <oss@buserror.net>
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

ls1012a has separate input root clocks for core PLLs versus the platform
PLL, with the latter described as sysclk in the hw docs.
Update the qoriq-clock binding to allow a second input clock, named
"coreclk".  If present, this clock will be used for the core PLLs.
Signed-off-by: Scott Wood <oss@buserror.net>
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

clk_generated_startup is called after clk_hw_register. So the first call to
get_parent will not have the correct value (i.e. 0) and because this is
cached, it may never be updated.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Fixes: df70aeef ("clk: at91: add generated clock driver")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

According to the MX7D Reference Manual the powerdown bit of
CCM_ANALOG_PLL_DDRn register is bit 20, so fix it accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

The Linksys WRT3200ACM CPU is clocked at 1866MHz. Add 1866MHz to the
list of supported CPU frequencies. Also update multiplier and divisor
for the l2clk and ddrclk.

Noticed by the following warning:
[    0.000000] Selected CPU frequency (16) unsupported
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

As for cp110, the initial intent when the binding of the ap806 system
controller was to have one flat node. The idea being that what is
currently a clock-only driver in drivers would become a MFD driver,
exposing the clock, GPIO and pinctrl functionality. However, after taking
a step back, this would lead to a messy binding. Indeed, a single node
would be a GPIO controller, clock controller, pinmux controller, and
more.

This patch adopts a more classical solution of a top-level syscon node
with sub-nodes for the individual devices. The main benefit will be to
have each functional block associated to its own sub-node where we can
put its own properties.

The introduction of the Armada 7K/8K is still in the early stage so the
plan is to remove the old binding. However, we don't want to break the
device tree compatibility for the few devices already in the field. For
this we still keep the support of the legacy compatible string with a big
warning in the kernel about updating the device tree.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/cc8c8c40fa4c4e71133033358992ec38e5aa2be5.1496239589.git-series.gregory.clement@free-electrons.com

As it was done for the cp110, this patch modifies the way the clock names
are created. The name of each clock is now created by using its physical
address as a prefix (as it was done for the platform device
names). Thanks to this we have an automatic way to compute a unique name.
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/e66cdd54d36c6bef78460a51e577f171b6ccb031.1496239589.git-series.gregory.clement@free-electrons.com

Instead of using &pdev->dev all over the place, introduce a pointer
variable for it.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/5a55e081d96fc6d2a28331b59df90f56d32a9f24.1496239589.git-series.gregory.clement@free-electrons.com

This patch updates the documentation according to the changes made in the
patch "clk: mvebu: ap806: introduce a new binding"
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/32e35c1d5919bdf9dc7d58678f0c0b462886d03e.1496239589.git-series.gregory.clement@free-electrons.com

This patch updates the documentation according to the change made in the
patch "clk: mvebu: ap806: do not depend anymore of the
*-clock-output-names": the clock names are no more part of the binding.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/d502b5abc68cbb5739ce72ba8be27528f9042a28.1496239589.git-series.gregory.clement@free-electrons.com

On Amlogic GX SoCs, there is two CEC controllers :
- An Amlogic CEC custom in the AO domain
- The Synopsys HDMI-TX Controller in the EE domain

Each of these controllers needs a 32.768KHz clock, but there is two paths :
- In the EE domain, the "32k_clk" this patchs is adding
- In the AO domain, with a more complex dual divider more precise setup

The AO 32K clock support will be pushed later in the corresponding
gxbb-aoclk driver when the AE CEC driver is ready.

The EE 32k_clk must be pushed earlier since mainline support for CEC in the
Synopsys HDMI-TX controller is nearby.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[Rebased patch on top of last changes]
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>

clk81 already has CLK_IS_CRITICAL so CLK_IGNORE_UNUSED is not
necessary
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>

Disabling clk81 results in an immediate freeze of the whole system. This
can happen "accidentally" when the last child-clock of clk81 is disabled
(in this case the common clock framework also disables clk81, even if it
was only enabled indirectly before).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>

It seems that the "cpu_clk" was carried over from the meson8b clock
controller driver. On Meson GX (GXBB/GXL/GXM) the registers which are
used by the cpu_clk have a different purpose (in other words: they don't
control the CPU clock anymore). HHI_SYS_CPU_CLK_CNTL1 bits 31:24 are
reserved according to the public S905 datasheet, while bit 23 is the
"A53_trace_clk_DIS" gate (which according to the datasheet should only
be used in case a silicon bug is discovered) and bits 22:20 are a
divider (A53_trace_clk). The meson clk-cpu code however expects that
bits 28:20 are reserved for a divider (according to the public S805
datasheet this "SCALE_DIV: This value represents an N+1 divider of the
input clock.").

The CPU clock on Meson GX SoCs is provided by the SCPI DVFS clock
driver instead. Two examples from a Meson GXL S905X SoC:
- vcpu (SCPI DVFS clock 0) rate: 1000000000 / cpu_clk rate: 708000000
- vcpu (SCPI DVFS clock 0) rate: 1512000000 / cpu_clk rate: 708000000

Unfortunately the CLKID_CPUCLK was already exported (but is currently
not used) to DT. Due to the removal of this clock definition there is
now a hole in the clk_hw_onecell_data (which is not a problem because
this case is already handled in gxbb_clkc_probe).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>

The CPU clock defined in the Meson GX clock driver is actually a
left-over from the Meson8b clock controller. Un-export the clock so we
can remove it from the driver.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>

Expose the clock ids of the three none AO uarts to the dt-bindings
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Helmut Klein <hgkr.klein@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[tidy the commit message to match similar change]
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>

Expose the SPICC gate clock to enable the SPICC controller.
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[tidy commit message to match similar changes]
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>

Expose the spdif master clock and the mux to select the appropriate spdif
clock parent depending on the data source.
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>

Expose cts_amclk in the device tree bindings
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>

Expose the clock gates required for the spdif output
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>

KConfig fix:
- clk: meson: gxbb: fix build error without RESET_CONTROLLER