- 28 Sep, 2020 40 commits
-
-
Ursula Braun authored
SMC Version 2 defines a first contact extension for CLC accept and CLC confirm. This patch covers sending and receiving of the CLC first contact extension. Signed-off-by:
Ursula Braun <ubraun@linux.ibm.com> Signed-off-by:
Karsten Graul <kgraul@linux.ibm.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Ursula Braun authored
The new format of SMCD V2 CLC accept and confirm is introduced, and building and checking of SMCD V2 CLC accepts / confirms is adapted accordingly. Signed-off-by:
-
Ursula Braun authored
SMCD Version 2 allows to propose up to 8 additional ISM devices offered to the peer as candidates for SMCD communication. This patch covers the server side, i.e. selection of an ISM device matching one of the proposed ISM devices, that will be used for CLC accept Signed-off-by:
-
Ursula Braun authored
The new format of an SMCD V2 CLC proposal is introduced, and building and checking of SMCD V2 CLC proposals is adapted accordingly. Signed-off-by:
-
Ursula Braun authored
SMCD Version 2 allows to propose up to 8 additional ISM devices offered to the peer as candidates for SMCD communication. This patch covers determination of the ISM devices to be proposed. ISM devices without PNETID are preferred, since ISM devices with PNETID are a V1 leftover and will disappear over the time. Signed-off-by:
-
Ursula Braun authored
SMCD version 2 allows usage of ISM devices with hardware PNETID only, if an Ethernet net_device exists with the same hardware PNETID. This requires to maintain a list of pnetids belonging to Ethernet net_devices, which is covered by this patch. Signed-off-by:
-
Ursula Braun authored
With SMCD version 2 the CHIDs of ISM devices are needed for the CLC handshake. This patch provides the new callback to retrieve the CHID of an ISM device. Signed-off-by:
-
Ursula Braun authored
SMCD version 2 defines a System Enterprise ID (short SEID). This patch contains the SEID creation and adds the callback to retrieve the created SEID. Signed-off-by:
-
Ursula Braun authored
SMCD Version 2 allows proposing of up to 8 ISM devices in addition to the native ISM device of SMCD Version 1. This patch prepares the struct smc_init_info to deal with these additional 8 ISM devices. Signed-off-by:
-
Ursula Braun authored
When sending CLC confirm and CLC accept, separate the trailing part of the message from the initial part (to be prepared for future first contact extension). Signed-off-by:
-
Ursula Braun authored
This patch provides better separation of device determinations in function smc_listen_work(). No functional change. Signed-off-by:
-
Ursula Braun authored
SMCD version 2 defines 2 more bits in the CLC header to specify version 2 types. This patch prepares better naming of the CLC header fields. No functional change. Signed-off-by:
-
Karsten Graul authored
Use the existing symbol _S instead of SMC_ASCII_BLANK, and introduce a helper to check if a pnetid is set. No functional change. Signed-off-by:
-
Wang Qing authored
Use kobj_to_dev() instead of container_of(). Signed-off-by:
Wang Qing <wangqing@vivo.com> Signed-off-by:
-
Lorenzo Bianconi authored
Try to recycle the xdp tx buffer into the in-irq page_pool cache if mvneta_txq_bufs_free is executed in the NAPI context for XDP_TX use case Signed-off-by:
Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by:
-
https://github.com/anguy11/next-queueDavid S. Miller authored
Tony Nguyen says: ==================== 1GbE Intel Wired LAN Driver Updates 2020-09-28 This series contains updates to igb, igc, and e1000e drivers. Sven Auhagen adds XDP support for igb. Gal Hammer allows for 82576 to display part number string correctly for igb. Sasha adds device IDs for i221 and i226 parts. Exposes LPI counters and removes unused fields in structures for igc. He also adds Meteor Lake support for e1000e. For igc, Andre renames IGC_TSYNCTXCTL_VALID to IGC_TSYNCTXCTL_TXTT_0 to match the datasheet and adds a warning if it's not set when expected. Removes the PTP Tx timestamp check in igc_ptp_tx_work() as it's already checked in the watchdog_task. Cleans up some code by removing invalid error bits, renaming a bit to match datasheet naming, and removing a, now unneeded, macro. Vinicius makes changes for igc PTP: removes calling SYSTIMR to latch timer value, stores PTP time before a reset, and rejects schedules with times in the future. v2: Remove 'inline' from igb_xdp_tx_queue_mapping() and igb_rx_offset() for patch 1 ==================== Signed-off-by: -
Sasha Neftin authored
Add devices IDs for the next LOM generations that will be available on the next Intel Client platform (Meteor Lake) This patch provides the initial support for these devices Signed-off-by:
Sasha Neftin <sasha.neftin@intel.com> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
Tony Nguyen <anthony.l.nguyen@intel.com>
-
Sasha Neftin authored
flash_bank_size and flash_base_addr field not in use and can be removed from a nvm_info structure Signed-off-by:
-
Vinicius Costa Gomes authored
When we set the BASET registers of i225 with a base_time in the future, i225 will "hold" all packets until that base_time is reached, causing a lot of TX Hangs. As this behaviour seems contrary to the expectations of the IEEE 802.1Q standard (section 8.6.9, especially 8.6.9.4.5), let's start by rejecting these types of schedules. If this is too limiting, we can for example, setup a timer to configure the BASET registers closer to the start time, only blocking the packets for a "short" while. Signed-off-by:
Vinicius Costa Gomes <vinicius.gomes@intel.com> Tested-by:
-
Vinicius Costa Gomes authored
The next patch will need a way to retrieve the current timestamp from the NIC's PTP clock. The 'i225' suffix is removed, if anything model specific is needed, those specifics should be hidden by this function. Signed-off-by:
-
Sasha Neftin authored
Boolean reset disable flag not applicable for i225 device and could be removed. Signed-off-by:
-
Vinicius Costa Gomes authored
Many TSN features depend on the internal PTP clock, so the internal PTP jumping when the adapter is reset can cause problems, usually in the form of "TX Hangs" warnings in the driver. The solution is to save the PTP time before a reset and restore it after the reset is done. The value of the PTP time is saved before a reset and we use the difference from CLOCK_MONOTONIC from reset time to now, to correct what's going to be the new PTP time. This is heavily inspired by commit bf4bf09b ("i40e: save PTP time before a device reset"). Signed-off-by:
-
Vinicius Costa Gomes authored
In i225, it's no longer necessary to use the SYSTIMR register to latch the timer value, the timestamp is latched when SYSTIML is read. Signed-off-by:
-
Sasha Neftin authored
Completion to commit 900d1e8b ("igc: Add LPI counters") LPI counters exposed by statistics update method. A EEE TX LPI counter reflect the transmitter entries EEE (IEEE 802.3az) into the LPI state. A EEE RX LPI counter reflect the receiver link partner entries into EEE(IEEE 802.3az) LPI state. Signed-off-by:
-
Andre Guedes authored
i225 advanced receive descriptor doesn't have the following extend error bits: CE, SE, SEQ, CXE. In addition to that, the bit TCPE is called L4E in the datasheet. Clean up the code accordingly, and get rid of the macro IGC_RXDEXT_ERR_FRAME_ERR_MASK since it doesn't make much sense anymore. Signed-off-by:
Andre Guedes <andre.guedes@intel.com> Tested-by:
-
Andre Guedes authored
The Tx timestamp timeout is already checked by the watchdog_task which runs periodically. In addition to that, from the ptp_tx work perspective, if __IGC_PTP_TX_IN_PROGRESS flag is set we always want handle the timestamp stored in hardware and update the skb. So remove the timeout check in igc_ptp_tx_work() function. Signed-off-by:
-
Andre Guedes authored
The ptp_tx work is scheduled only if TSICR.TXTS bit is set, therefore TSYNCTXCTL.TXTT_0 bit is expected to be set when we check it igc_ptp_tx_ work(). If it isn't, something is really off and rescheduling the ptp_tx work to check it later doesn't help much. This patch changes the code to WARN_ON_ONCE() if this situation ever happens. Signed-off-by:
-
Andre Guedes authored
Rename the IGC_TSYNCTXCTL_VALID macro to IGC_TSYNCTXCTL_TXTT_0 so it matches the datasheet. Signed-off-by:
-
Sasha Neftin authored
Add new device ID's for the next step of the silicon and reflect i221 and i226 parts Signed-off-by:
-
Gal Hammer authored
Fixed flash presence check for 82576 controllers so the part number string is read and displayed correctly. Signed-off-by:
Gal Hammer <ghammer@redhat.com> Tested-by:
-
Sven Auhagen authored
Add XDP support to the IGB driver. The implementation follows the IXGBE XDP implementation closely and I used the following patches as basis: 1. commit 92470808 ("ixgbe: add XDP support for pass and drop actions") 2. commit 33fdc82f ("ixgbe: add support for XDP_TX action") 3. commit ed93a398 ("ixgbe: tweak page counting for XDP_REDIRECT") Due to the hardware constraints of the devices using the IGB driver we must share the TX queues with XDP which means locking the TX queue for XDP. I ran tests on an older device to get better numbers. Test machine: Intel(R) Atom(TM) CPU C2338 @ 1.74GHz (2 Cores) 2x Intel I211 Routing Original Driver Network Stack: 382 Kpps Routing XDP Redirect (xdp_fwd_kern): 1.48 Mpps XDP Drop: 1.48 Mpps Using XDP we can achieve line rate forwarding even on an older Intel Atom CPU. Signed-off-by:
Sven Auhagen <sven.auhagen@voleatech.de> Tested-by:
Sandeep Penigalapati <sandeep.penigalapati@intel.com> Signed-off-by:
-
David S. Miller authored
Jakub Kicinski says: ==================== udp_tunnel: convert Intel drivers with shared tables This set converts Intel drivers which have the ability to spawn multiple netdevs, but have only one UDP tunnel port table. Appropriate support is added to the core infra in patch 1, followed by netdevsim support and a selftest. The table sharing works by core attaching the same table structure to all devices sharing the table. This means the reference count has to accommodate potentially large values. Once core is ready i40e and ice are converted. These are complex drivers, but we got a tested-by from Aaron, so we should be good :) Compared to v1 I've made sure the selftest is executable. Other than that patches 8 and 9 are actually from the Mellanox conversion series were kept out to avoid Mellanox vs Intel conflicts. Last patch is new, some docs to let users knows ethtool can now display UDP tunnel info. ==================== Signed-off-by: -
Jakub Kicinski authored
Add some information about VxLAN-related netdev features and how to dump port table via ethtool. Signed-off-by:
Jakub Kicinski <kuba@kernel.org> Signed-off-by:
-
Jakub Kicinski authored
Check UDP_TUNNEL_NIC_INFO_STATIC_IANA_VXLAN works as expected. Signed-off-by:
-
Jakub Kicinski authored
Allow setting UDP_TUNNEL_NIC_INFO_STATIC_IANA_VXLAN. Signed-off-by:
-
Jakub Kicinski authored
Convert ice to the new infra, use share port tables. Leave a tiny bit more error checking in place than usual, because this driver really does quite a bit of magic. We need to calculate the number of VxLAN and GENEVE entries the firmware has reserved. Thanks to the conversion the driver will no longer sleep in an atomic section. Signed-off-by:
-
Jakub Kicinski authored
ice_get_open_tunnel_port() is always passed TNL_ALL as the second parameter. Signed-off-by:
-
Jakub Kicinski authored
Make use of the "shared port table" to convert i40e to the new infra. i40e did not have any reference tracking, locking is also dodgy because rtnl gets released while talking to FW, so port may get removed from the table while it's getting added etc. On the good side i40e does not seem to be using the ports for TX so we can remove the table from the driver state completely. Signed-off-by:
-
Jakub Kicinski authored
Add a test run of checks validating the shared UDP tunnel port tables function as we expect. Signed-off-by:
-
Jakub Kicinski authored
Add the ability to simulate a device with a shared UDP tunnel port table. Try to reject the configurations and actions which are not supported by the core, so we don't get syzcaller etc. warning reports. Signed-off-by:
-
