Certain bridge chips use a GPIO to indicate the cable status instead
of the I_DP_HPD pin.  This adds an optional device-tree property,
"samsung,hpd-gpio", to the exynos-dp controller which indicates that
the specified GPIO should be used for hotplug detection.
The GPIO is then set up as an edge-triggered interrupt where the
rising edge indicates hotplug-in and the falling edge indicates hotplug-out.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

Exynos drm driver is a single driver so pm operation
for kms drivers should be done by connector->dpms
at top level driver.

If kms driver has its own pm interfaces, single driver model
would be broken so this patch removes unnecessary pm interfaces
from dsi driver.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>

Exyno drm driver has no real hardware device, and
runtime pm operation should be done by sub drivers.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>

The patch separates dpi related routines from fimd.

Changelog v2:
- Rename ctx->dpi to ctx->display
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

subdrv_probe callback of virtual display driver will be
called by exynos_drm_device_subdrv_probe() to create crtc
and encoder/connector for virtual display driver.
So it fixes comments to exynos_drm_device_subdrv probe call.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>

When connector is created, if connector->polled is
DRM_CONNECTOR_POLL_CONNECT then drm_kms_helper_hotplug_event
function isn't called at drm_helper_hpd_irq_event because the
function will be called only in case of DRM_CONNECTOR_POLL_HPD.

So this patch sets always DRM_CONNECTOR_POLL_HPD flag to
connector->polled of parallel panel driver at connector creation.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>

This patch adds component framework support to resolve
the probe order issue.

Until now, exynos drm had used codes specific to exynos drm
to resolve that issue so with this patch, the specific codes
are removed.
Signed-off-by: Inki Dae <inki.dae@samsung.com>

Signed-off-by: Inki Dae <inki.dae@samsung.com>

If any fimd channel was already active, initializing iommu will result
in a PAGE FAULT (e.e. u-boot could have turned on the display and
not disabled it before the kernel starts). This patch checks if any
channel is active before initializing iommu and disables it.
Signed-off-by: Akshu Agrawal <akshu.a@samsung.com>
Signed-off-by: Prathyush K <prathyush.k@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

In the case of that only one branch of a conditional statement is
a single statement, braces are added to both branches.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

Make local symbols static, because these are used only in this
file.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

Make local symbole static, because this is used only in this file.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

Exynos drm driver cannot support DRIVER_HAVE_IRQ feature because it uses
driver specific one instead of routine of drm framework to
install/uninstall irq handler.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

AFAICT, the fb_base of a drm_device's mode_config is never used.  It isn't
accessed by core drm, it isn't used by fbmem, and it isn't exposed to user
space.

Furthermore, it is probably supposed to be a physical address, not the
dma address mapped to the display controller, so this is just wrong.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

Kernel access to the eyxnos fbdev framebuffer is via its gem object's
kernel mapping (kvaddr, stored in info->screen_base).

User space access is provided by mmap(), read() and write() of /dev/fb/fb0.
These functions also only use screen_base/screen_size().

Therefore, it is not necessary to set fix->smem_{start,len} or
fix->mmio_{start,len} fields.

This avoids leaking kernel, physical and dma mapped addresses to user
space via the ioctls FBIOGET_VSCREENINFO and FBIOGET_FSCREENINFO.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

This adds an encoder type for DP MST encoders.
Reviewed-by: Todd Previte <tprevite@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

This makes drm_get_encoder_name() thread safe.

Reference: http://lkml.kernel.org/r/645ee6e22cad47d38a2b35c21c8d5fe3@DC1-MBX-01\
.ptsecurity.ru
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

This makes drm_get_connector_name() thread safe.

[airlied: fix to build.]

Reference: http://lkml.kernel.org/r/645ee6e22cad47d38a2b35c21c8d5fe3@DC1-MBX-01.ptsecurity.ruSigned-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Commit 9dc40560 (drm/dp: let drivers specify the name of the I2C-
over-AUX adapter) introduced a new field but didn't add the proper
kernel-doc for it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

shmem_read_mapping_page() uses mapping_gfp_mask(mapping) as default gfp
mask. No reason to use shmem_read_mapping_page_gfp() directly if we want
the default behavior.
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

shmem supports page-relocations during swapin since quite some time. It
was implemented in:

    commit bde05d1c
    Author: Hugh Dickins <hughd@google.com>
    Date:   Tue May 29 15:06:38 2012 -0700

        shmem: replace page if mapping excludes its zone

The gem-comment about wrongly placed DMA32 pages is no longer valid.
Replace it with a proper comment but keep the BUG_ON() to verify correct
shmem behavior.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>

This issue was reported by coccicheck using the semantic patch
at scripts/coccinelle/api/memdup.cocci
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Dave Airlie <airlied@redhat.com>

The shmobile DRM driver is only useful on SuperH and shmobile unless
build testing. I am dropping the SuperH dependencies though because
the driver doesn't even build there, so in practice it is an arm-only
driver for now.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

The Renesas R-Car Display Unit driver is only useful on shmobile
unless build testing. The LVDS output is useful on an even more
reduced hardware set.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

DRM is pretty much the main user of this stuff (if we ignore the sysfs
interface used by X, i.e. by the same gang of people writing the drm
drivers). So shovel it into Dave's responsibility to avoid patches
getting lost on lkml.

With this get_maintainers will rout vgaarb and switcheroo patches
correctly.

Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: linux-kernel@vger.kernel.org
References: https://lkml.org/lkml/2014/5/25/94Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Started documenting drm properties for drm drivers. This patch provides
information about properties in drm, i915, psb and cdv/gma-500. Information
about other properties can be added on top of these.

v2: Added description of drm properties in armada, exynos, i2c/ch7006, noveau,
omap, qxl, radeon, rcar-du

v3: Removed "Property Object" column since it is implementation related. Property
type column refined.[Ville's review comments]

v4: Removed whitespace warnings and minor nits. [Randy's review comments]

v5: Restructured output for ENUM properties

v6: Review comments on formatting the table. [Laurent's review comments]

v7: Minor restructuring. [Laurent's review comments]

Cc: Rob Landley <rob@landley.net>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Cc: David Herrmann <dh.herrmann@gmail.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Ville Syrjälä" <ville.syrjala@linux.intel.com>
Cc: Sagar Kamble <sagar.a.kamble@intel.com>
Cc: "Purushothaman, Vijay A" <vijay.a.purushothaman@intel.com>
Cc: linux-doc@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Sagar Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

The kerneldoc header of ttm_bo_create() was referring to another
(nonexisting) function and had a few obsolete or incorrect arguments.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

The 800x600 (SVGA) screen resolution was lacking in the set of
built-in selectable EDID screen resolutions that can be used to
repair misbehaving monitor firmware.

This patch adds the related data set and expands the documentation.
Note that the SVGA bit occupies a different byte to all the existing
users of the established timing bits forcing a rework of the
ESTABLISHED_TIMINGS_BITS macro.

Tested new EDID on an aged (and misbehaving) industrial LCD panel;
existing EDIDs still pass edid-decode's checksum checks.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Carsten Emde <C.Emde@osadl.org>
Cc: linux-doc@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Fix spelling typo in DocBook/drm.tmpl
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

This just adds the defines from the DP 1.2 spec, which we
will use later.

fix some DP MST to 1.2 MST
Signed-off-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Todd Previte <tprevite@gmail.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>

Pull in latest updates to AST driver.

* 'ast-updates' of ssh://people.freedesktop.org/~/linux:
  drm/ast: initial DP501 support (v0.2)
  drm/ast: rename the mindwm/moutdwm and deinline them
  drm/ast: resync the dram post code with upstream
  drm/ast: add AST 2400 support.
  drm/ast: add widescreen + rb modes from X.org driver (v2)

This is the initial attempt at porting the DP501 code from the userspace
driver,

the firmware file is in
http://people.freedesktop.org/~airlied/ast_dp501_fw.bin

this should really be exposed as another encoder/connector that is cloneable

v0.2:
init 3rd tx properly,
add scratch reduction of VRAM size
backup firmware properly.
Signed-off-by: Dave Airlie <airlied@redhat.com>

we'll need these elsewhere for dp501.
Signed-off-by: Dave Airlie <airlied@redhat.com>

This resyncs the dram post code with the upstream X.org driver
where ast have improved the code for setting up the dram chips.
Signed-off-by: Dave Airlie <airlied@redhat.com>

This is ported from the userspace driver.

Untested on any ast2400 hw so far.
Signed-off-by: Dave Airlie <airlied@redhat.com>

This syncs up the mode code from the X.org driver upstream,
and adds the mode validation step for hw that doesn't have
widescreen.

v2: (from Egbert Eich <eich@suse.de)
squash drm/ast: Use correct structure member for mode validation
to avoid bisect regression.

In struct drm_display_mode crtc_hdisplay and crtc_vdisplay are holding
the crtc parameters after mode fixup. For validation we need hdisplay and
vdisplay.
Signed-off-by: Egbert Eich <eich@suse.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>

- ring init improvements (Chris)
- vebox2 support (Zhao Yakui)
- more prep work for runtime pm on Baytrail (Imre)
- eDram support for BDW (Ben)
- prep work for userptr support (Chris)
- first parts of the encoder->mode_set callback removal (Daniel)
- 64b reloc fixes (Ben)
- first part of atomic plane updates (Ville)

* tag 'drm-intel-next-2014-05-06' of git://anongit.freedesktop.org/drm-intel: (75 commits)
  drm/i915: Remove useless checks from primary enable/disable
  drm/i915: Merge LP1+ watermarks in safer way
  drm/i915: Make sure computed watermarks never overflow the registers
  drm/i915: Add pipe update trace points
  drm/i915: Perform primary enable/disable atomically with sprite updates
  drm/i915: Make sprite updates atomic
  drm/i915: Support 64b relocations
  drm/i915: Support 64b execbuf
  drm/i915/sdvo: Remove ->mode_set callback
  drm/i915/crt: Remove ->mode_set callback
  drm/i915/tv: Remove ->mode_set callback
  drm/i915/tv: Rip out pipe-disabling nonsense from ->mode_set
  drm/i915/tv: De-magic device check
  drm/i915/tv: extract set_color_conversion
  drm/i915/tv: extract set_tv_mode_timings
  drm/i915/dvo: Remove ->mode_set callback
  drm/i915: Make encoder->mode_set callbacks optional
  drm/i915: Make primary_enabled match the actual hardware state
  drm/i915: Move ring_begin to signal()
  drm/i915: Virtualize the ringbuffer signal func
  ...

Update pull request with drm core patches. Mostly some polish for the
primary plane stuff and a pile of patches all over from Thierry. Has
survived a few days in drm-intel-nightly without causing ill.

I've frobbed my scripts a bit to also tag my topic branches so that you
have something stable to pull - I've accidentally pushed a bunch more
patches onto this branch before you've taken the old pull request.

* tag 'topic/core-stuff-2014-05-05' of git://anongit.freedesktop.org/drm-intel:
  drm: Make drm_crtc_helper_disable() return void
  drm: Fix indentation of closing brace
  drm/dp: Fix typo in comment
  drm: Fixup flip-work kerneldoc
  drm/fb: Fix typos
  drm/edid: Cleanup kerneldoc
  drm/edid: Drop revision argument for drm_mode_std()
  drm: Try to acquire modeset lock on panic or sysrq
  drm: remove unused argument from drm_open_helper
  drm: Handle ->disable_plane failures correctly
  drm: Simplify fb refcounting rules around ->update_plane
  drm/crtc-helper: gc usless connector loop in disable_unused_functions
  drm/plane_helper: don't disable plane in destroy function
  drm/plane-helper: Fix primary plane scaling check
  drm: make mode_valid callback optional
  drm/edid: Fill PAR in AVI infoframe based on CEA mode list