- 21 Apr, 2016 33 commits
-
-
David S. Miller authored
Florian Fainelli says: ==================== net: bcmsysport: utilize newer NAPI APIs These two patches are very analoguous to what was already submitted for BCMGENET and switch the SYSTEMPORT driver to utilizing __napi_schedule_irqoff() and napi_complete_done for the RX NAPI context. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Florian Fainelli authored
By using napi_complete_done(), we allow fine tuning of /sys/class/net/ethX/gro_flush_timeout for higher GRO aggregation efficiency for a Gbit NIC. Check commit 24d2e4a5 ("tg3: use napi_complete_done()") for details. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Florian Fainelli authored
Both bcm_sysport_tx_isr() and bcm_sysport_rx_isr() run in hard irq context, we do not need to block irq again. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Nicolas Dichtel says: ==================== libnl: enhance API to ease 64bit alignment for attribute Here is a proposal to add more helpers in the libnetlink to manage 64-bit alignment issues. Note that this series was only tested on x86 by tweeking CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS and adding some traces. The first patch adds helpers for 64bit alignment and other patches use them. We could also add helpers for nla_put_u64() and its variants if needed. v1 -> v2: - remove patch #1 - split patch #2 (now #1 and #2) - add nla_need_padding_for_64bit() ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Nicolas Dichtel authored
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Nicolas Dichtel authored
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Nicolas Dichtel authored
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Nicolas Dichtel authored
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Alexander Duyck authored
This patch adds support for the checksum enabled versions of UDP and GRE tunnels. With this change we should be able to send and receive GSO frames of these types over the veth pair without needing to segment the packets. Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Alexander Duyck authored
This patch folds NETIF_F_ALL_TSO into the bitmask for NETIF_F_GSO_SOFTWARE. The idea is to avoid duplication of defines since the only difference between the two was the GSO_UDP bit. Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Dan Carpenter authored
We intended to test "err" and not "skb". Fixes: aed069df ('ip_tunnel_core: iptunnel_handle_offloads returns int and doesn't free skb') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Alexander Duyck <aduyck@mirantis.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Peter Heise authored
Removed .type field from NLA to do proper length checking. Reported by Daniel Borkmann and Julia Lawall. Signed-off-by: Peter Heise <peter.heise@airbus.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Xin Long authored
EXPIRES_IN_MS macro comes from net/ipv4/inet_diag.c and dates back to before jiffies_to_msecs() has been introduced. Now we can remove it and use jiffies_to_msecs(). Suggested-by: Jakub Sitnicki <jkbs@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Jakub Sitnicki <jkbs@redhat.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Alexei Starovoitov authored
move trace_call_bpf() into helper function to minimize the size of perf_trace_*() tracepoint handlers. text data bss dec hex filename 10541679 5526646 2945024 19013349 1221ee5 vmlinux_before 10509422 5526646 2945024 18981092 121a0e4 vmlinux_after It may seem that perf_fetch_caller_regs() can also be moved, but that is incorrect, since ip/sp will be wrong. bpf+tracepoint performance is not affected, since perf_swevent_put_recursion_context() is now inlined. export_symbol_gpl can also be dropped. No measurable change in normal perf tracepoints. Suggested-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Vivien Didelot authored
Having the tag protocol in dsa_switch_driver for setup time and in dsa_switch_tree for runtime is enough. Remove dsa_switch's one. Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queueDavid S. Miller authored
Jeff Kirsher says: ==================== 100GbE Intel Wired LAN Driver Updates 2016-04-20 This series contains updates to fm10k only. Jacob provides majority of the changes in this series, starting with the addition of helper functions to reduce code duplication and the amount of code indentation. Fixed the use or should we say abuse of the ethtool stats API, which could result in corrupt memory or misleading statistic output. Added the appropriate rtnl_lock() and rtnl_unlock() to avoid RCU warnings during AER events. Come to find out, the PTP/1588 support is not working with the current version of switch management software and possibly never worked, so just remove support for PTP/1588 for now. Fixed how error responses from the switch manager after a LPORT_MAP request are handled, originally which were silently being ignored. Fixed up code documentation to hopefully ease the code and comment comprehension. Fixed a possible NULL pointer dereference after a kcalloc(), where when writing a new default redirection table, and we needed to populate a new RSS table using ethtool_rxfh_indir_default(). We populate this table into a region of memory allocated using kcalloc() but never check it for NULL. Alex adds support for bulk transmit cleanup for fm10k, like he did for all of our other drivers. Ngai-Mint fixes a number of issues with the unicast and multicast address syncs. Where an issue would occur when the netdev is pre-configured to either multicast mode and is enabled for the first time. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jacob Keller authored
Check for and handle IPv6 extended headers so that Tx checksum offload can be done. Also use skb_checksum_help for unexpected cases. This was originally discovered in ixgbe. Reported-by: Mark Rustad <mark.d.rustad@intel.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Jacob Keller authored
Update every header file and other locations to consistently use Intel(R) instead of just Intel. Also update copyright year of files which we modified. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Jacob Keller authored
When writing a new default redirection table, we needed to populate a new RSS table using ethtool_rxfh_indir_default. We populated this table into a region of memory allocated using kcalloc, but never checked this for NULL. Fix this by moving the default table generation into fm10k_write_reta. If this function is passed a table, use it. Otherwise, generate the default table using ethtool_rxfh_indir_default, 4 at at time. Fixes: 0ea7fae4 ("fm10k: use ethtool_rxfh_indir_default for default redirection table") Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Ngai-Mint Kwan authored
Deleting lport when multicast mode is configured to FM10K_XCAST_MODE_ALLMULTI or FM10K_XCAST_MODE_PROMISC will result in generating orphaned multicast-group entries in the switch manager. Before deleting the lport, reset multicast mode to FM10K_XCAST_MODE_NONE to flush out these multicast-group entries. Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Jacob Keller authored
The original comment may be read incorrectly as referring to checking the *entire* length is zero. However, it merely checks only the reserved bits of both length and reserved in a small amount of code. Update the comment to indicate this is a clever trick and clearly spell out that it only checks the reserve bits. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Jacob Keller authored
Use a new #define FM10K_VLAN_OVERRIDE even though we're using the exact same bit. The reason for this is clarity in the code, otherwise you can read FM10K_VLAN_CLEAR and think it should be removed. Also add a comment explaining why the FM10K_VLAN_OVERRIDE bit is set. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Jacob Keller authored
The diagram represents bit layout of the multi-bit VLAN update message format. Typically these diagrams are drawn using some power of 2 as the base, to more easily grasp where fields split. Although the numbers above can make it somewhat easy to understand which bit you're looking at, it makes the break points not line up. Re-draw the numbers using base 8, and mark the bit values every 8 bits at the top. This should make it more easy to grasp the table quickly. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Jacob Keller authored
fm10k_tlv_parse_attr is supposed to return FM10K_NOT_IMPLEMENTED for any TLV who's attribute id lies outside the range of results. It does not do this today. In addition, the documentation does not indicate that other attributes which are not implemented for a given TLV will be silently ignored. Fix this. Clean up the logic so that we don't rely on the fact that FM10K_NOT_IMPLEMENTED is greater than zero, as this can easily cause confusion. A future extension could look into some way of reporting unknown TLVs in order to make issues more easily discoverable. We can't just return FM10K_NOT_IMPLEMENTED here because we don't want to drop the entire message if it has an unknown TLV. While here, update the copyright year. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Jacob Keller authored
fm10k_io_error_detected() does not need to call pci_disable_device(). In the cases where the reset needs to occur, the stack flow will result in calling fm10k_remove() which already disables the PCI device. If we leave the pci_disable_device(), we result in a warning about disabling an already disabled device. Many PCI drivers do call pci_disable_device() in their .error_detected() routines, but it does not appear to be required. In addition, these drivers have a check "is_pci_enabled()" call in their remove routines, which is how they chose to handle the duplicate device disable. This seems incorrect, since the PCI device structure is reference counted. It is very possible that the reference count for the PCI device could be greater than 1. In this case, you would remove the PCI device within the error_detected routine, reducing count to 1, then remove it again in the remove function, reducing it to zero. This would result in yet another disable somewhere else failing. Thus, we shouldn't be using is_pci_enabled() to check for this issue. Instead, just remove the extraneous pci_device_disable() found within the error_detected routine. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Jacob Keller authored
Currently, any error responses from the switch manager after an LPORT_MAP request are silently ignored. At most the mailbox message will be reported as an error. This can result in unexpected behavior when the switch manager has configured a port with zero bandwidth. Add support for reading the fm10k_swapi_error structure from LPORT_MAP responses. If the message contains the necessary TLV and has a non-zero error code, report link down, clear the dglort_map, and delay the next get_host_state call by a reasonable delay. Also log an error message indicating that the LPORT_MAP request failed. The delay ensures preventing an interrupt storm on the switch manager, and reduces the number of mailbox messages we send in this scenario drastically. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Ngai-Mint Kwan authored
Multicast mode checking is no longer a requirement to perform unicast and multicast address syncs. Specifically, a device operating in promiscuous and/or all multicast mode is not excluded. The issue occurs when the netdev is pre-configured to either multicast mode and is enabled for the first time. The multicast-group table in the Switch Manager will be missing obvious multicast entries associated to this netdev. Changes were also made to disallow unicast and multicast syncs with VLAN 0. The Switch Manager considers VLAN 0 to be an invalid entry. Requests with VLAN 0 by the netdev are only generated when the driver is freshly installed and the default VID is not set. Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Jacob Keller authored
The 1588 support within fm10k does not work correctly with the current version of the switch management software, and likely never worked correctly to begin with. Remove support for PTP/1588. Update copyright year for all these files while we're touching them. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Jacob Keller authored
During an AER action response, we were calling fm10k_close without holding the rtnl_lock() which could lead to possible RCU warnings being produced due to 64bit stat updates among other causes. Similarly, we need rtnl_lock() around fm10k_open during fm10k_io_resume. Follow the same pattern elsewhere in the driver and protect the entire open/close sequence. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Jacob Keller authored
Use DRV_SUMMARY, similar to DRV_VERSION so that we don't have to duplicate the driver summary in multiple places. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Alexander Duyck authored
This patch enables bulk free in Tx cleanup for fm10k and cleans up the boolean logic in the polling routines for fm10k in the hopes of avoiding any mix-ups similar to what occurred with i40e and i40evf. Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Jacob Keller authored
This change fixes an (ab)use of the ethtool stats API, which could result in corrupt memory or misleading stat output. The ethtool stats API is not robust enough to handle varying number of statistics due to how it requests the size and allocates memory. Remove the poorly conceived support originally added for extra debug statistics. In the future, a new stats API may open up the ability to display these statistics. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Jacob Keller authored
Reduce duplicate code and the amount of indentation by adding fm10k_add_stat_strings and fm10k_add_ethtool_stats functions which help add fm10k_stat structures to the ethtool stats callbacks. This helps increase ease of use for future stat additions, and increases code readability. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
- 20 Apr, 2016 7 commits
-
-
Roopa Prabhu authored
This patch adds a new RTM_GETSTATS message to query link stats via netlink from the kernel. RTM_NEWLINK also dumps stats today, but RTM_NEWLINK returns a lot more than just stats and is expensive in some cases when frequent polling for stats from userspace is a common operation. RTM_GETSTATS is an attempt to provide a light weight netlink message to explicity query only link stats from the kernel on an interface. The idea is to also keep it extensible so that new kinds of stats can be added to it in the future. This patch adds the following attribute for NETDEV stats: struct nla_policy ifla_stats_policy[IFLA_STATS_MAX + 1] = { [IFLA_STATS_LINK_64] = { .len = sizeof(struct rtnl_link_stats64) }, }; Like any other rtnetlink message, RTM_GETSTATS can be used to get stats of a single interface or all interfaces with NLM_F_DUMP. Future possible new types of stat attributes: link af stats: - IFLA_STATS_LINK_IPV6 (nested. for ipv6 stats) - IFLA_STATS_LINK_MPLS (nested. for mpls/mdev stats) extended stats: - IFLA_STATS_LINK_EXTENDED (nested. extended software netdev stats like bridge, vlan, vxlan etc) - IFLA_STATS_LINK_HW_EXTENDED (nested. extended hardware stats which are available via ethtool today) This patch also declares a filter mask for all stat attributes. User has to provide a mask of stats attributes to query. filter mask can be specified in the new hdr 'struct if_stats_msg' for stats messages. Other important field in the header is the ifindex. This api can also include attributes for global stats (eg tcp) in the future. When global stats are included in a stats msg, the ifindex in the header must be zero. A single stats message cannot contain both global and netdev specific stats. To easily distinguish them, netdev specific stat attributes name are prefixed with IFLA_STATS_LINK_ Without any attributes in the filter_mask, no stats will be returned. This patch has been tested with mofified iproute2 ifstat. Suggested-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Netlink messages are appended, one object at a time, to the end of the SKB. Therefore we need to test skb_tail_pointer() not skb->data for alignment. Fixes: 35c58459 ("net: Add helpers for 64-bit aligning netlink attributes.") Signed-off-by: David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
HAVE_EFFICIENT_UNALIGNED_ACCESS needs CONFIG_ prefix. Also add a comment in nla_align_64bit() explaining we have to add a padding if current skb->data is aligned, as it certainly can be confusing. Fixes: 35c58459 ("net: Add helpers for 64-bit aligning netlink attributes.") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Peter Heise authored
New field (IFLA_HSR_VERSION) was added in the middle of an existing ENUM and would break kernel ABI, therefore moved to the end. Reported by Stephen Hemminger. Signed-off-by: Peter Heise <peter.heise@airbus.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Vivien Didelot authored
The dsa_slave_priv structure does not need a pointer to its net_device. Kill it. Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Daniel Borkmann says: ==================== BPF updates This minor set adds a new helper bpf_event_output() for eBPF cls/act program types which allows to pass events to user space applications. For details, please see individual patches. v1 -> v2: - Address kbuild bot found compile issue in patch 2 - Rest as is ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Daniel Borkmann authored
This patch adds a new helper for cls/act programs that can push events to user space applications. For networking, this can be f.e. for sampling, debugging, logging purposes or pushing of arbitrary wake-up events. The idea is similar to a43eec30 ("bpf: introduce bpf_perf_event_output() helper") and 39111695 ("samples: bpf: add bpf_perf_event_output example"). The eBPF program utilizes a perf event array map that user space populates with fds from perf_event_open(), the eBPF program calls into the helper f.e. as skb_event_output(skb, &my_map, BPF_F_CURRENT_CPU, raw, sizeof(raw)) so that the raw data is pushed into the fd f.e. at the map index of the current CPU. User space can poll/mmap/etc on this and has a data channel for receiving events that can be post-processed. The nice thing is that since the eBPF program and user space application making use of it are tightly coupled, they can define their own arbitrary raw data format and what/when they want to push. While f.e. packet headers could be one part of the meta data that is being pushed, this is not a substitute for things like packet sockets as whole packet is not being pushed and push is only done in a single direction. Intention is more of a generically usable, efficient event pipe to applications. Workflow is that tc can pin the map and applications can attach themselves e.g. after cls/act setup to one or multiple map slots, demuxing is done by the eBPF program. Adding this facility is with minimal effort, it reuses the helper introduced in a43eec30 ("bpf: introduce bpf_perf_event_output() helper") and we get its functionality for free by overloading its BPF_FUNC_ identifier for cls/act programs, ctx is currently unused, but will be made use of in future. Example will be added to iproute2's BPF example files. Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-