Commit 5a0e3ad6 causes slab.h to be included twice in many of the
Gigaset driver's source files, first via the common include file
gigaset.h and then a second time directly. Drop the spares, and
use the opportunity to clean up a few more similar cases.

Impact: cleanup, no functional change
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
CC: Tejun Heo <tj@kernel.org>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The af_packet protocol is used by Perl to do ioctls as reported by
Stephane Riviere:

"Net::RawIP relies on SIOCGIFADDR et SIOCGIFHWADDR to get the IP and MAC
addresses of the network interface."

But in a new network namespace these ioctl fail because it is disabled for
a namespace different from the init_net_ns.

These two lines should not be there as af_inet and af_packet are
namespace aware since a long time now. I suppose we forget to remove these
lines because we sent the af_packet first, before af_inet was supported.
Signed-off-by: Daniel Lezcano <daniel.lezcano@free.fr>
Reported-by: Stephane Riviere <stephane.riviere@regis-dgac.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

tx_queue is used as a temporary queue when not allowed to queue skb
directly to the hw device driver (which may sleep). Most paths flush
it before returning, but ppp_start() currently cannot. Make sure we
don't leave skbs pointing to a non-existent device.

Thanks to Michael Barkowski for reporting this problem.
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

Eric Paris got following trace with a linux-next kernel

[   14.203970] BUG: using smp_processor_id() in preemptible [00000000]
code: avahi-daemon/2093
[   14.204025] caller is netif_rx+0xfa/0x110
[   14.204035] Call Trace:
[   14.204064]  [<ffffffff81278fe5>] debug_smp_processor_id+0x105/0x110
[   14.204070]  [<ffffffff8142163a>] netif_rx+0xfa/0x110
[   14.204090]  [<ffffffff8145b631>] ip_dev_loopback_xmit+0x71/0xa0
[   14.204095]  [<ffffffff8145b892>] ip_mc_output+0x192/0x2c0
[   14.204099]  [<ffffffff8145d610>] ip_local_out+0x20/0x30
[   14.204105]  [<ffffffff8145d8ad>] ip_push_pending_frames+0x28d/0x3d0
[   14.204119]  [<ffffffff8147f1cc>] udp_push_pending_frames+0x14c/0x400
[   14.204125]  [<ffffffff814803fc>] udp_sendmsg+0x39c/0x790
[   14.204137]  [<ffffffff814891d5>] inet_sendmsg+0x45/0x80
[   14.204149]  [<ffffffff8140af91>] sock_sendmsg+0xf1/0x110
[   14.204189]  [<ffffffff8140dc6c>] sys_sendmsg+0x20c/0x380
[   14.204233]  [<ffffffff8100ad82>] system_call_fastpath+0x16/0x1b

While current linux-2.6 kernel doesnt emit this warning, bug is latent
and might cause unexpected failures.

ip_dev_loopback_xmit() runs in process context, preemption enabled, so
must call netif_rx_ni() instead of netif_rx(), to make sure that we
process pending software interrupt.

Same change for ip6_dev_loopback_xmit()
Reported-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When dev_pick_tx() caches tx queue_index on a socket, we must check
socket dst_entry matches skb one, or risk a crash later, as reported by
Denys Fedorysychenko, if old packets are in flight during a route
change, involving devices with different number of queues.

Bug introduced by commit a4ee3ce3
(net: Use sk_tx_queue_mapping for connected sockets)
Reported-by: Denys Fedorysychenko <nuclearcat@nuclearcat.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Followup of commit 634a4b20

Allow tnode_get_child_rcu() to be called either under rcu_read_lock()
protection or with RTNL held.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The following situation was observed in the field:
tap1 sends packets, tap2 does not consume them, as a result
tap1 can not be closed. This happens because
tun/tap devices can hang on to skbs undefinitely.

As noted by Herbert, possible solutions include a timeout followed by a
copy/change of ownership of the skb, or always copying/changing
ownership if we're going into a hostile device.

This patch implements the second approach.

Note: one issue still remaining is that since skbs
keep reference to tun socket and tun socket has a
reference to tun device, we won't flush backlog,
instead simply waiting for all skbs to get transmitted.
At least this is not user-triggerable, and
this was not reported in practice, my assumption is
other devices besides tap complete an skb
within finite time after it has been queued.

A possible solution for the second issue
would not to have socket reference the device,
instead, implement dev->destructor for tun, and
wait for all skbs to complete there, but this
needs some thought, probably too risky for 2.6.34.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Yan Vugenfirer <yvugenfi@redhat.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is a fix for bug 572201 @ bugs.debian.org

This patch fixes the TX_LIMIT feature flag. The previous logic check
for TX_LIMIT2 also took into account a device that only had TX_LIMIT
set.
Reported-by: Stephen Mulcahu <stephen.mulcahy@deri.org>
Reported-by: Ben Huchings <ben@decadent.org.uk>
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

smc91c92_cs:
  * define multicast_table as unsigned char
  * remove unnecessary "#ifndef final_version"
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

At this point optlen == sizeof(sfilter) but some compilers are dumb.

Reported-by: Németh Márton <nm127@freemail.h
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tx ring buffers after tx_ring->next_to_use are volatile and could
change, possibly causing a crash.  Stop cleaning when we hit
tx_ring->next_to_use.
Signed-off-by: Terry Loftin <terry.loftin@hp.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Restrict Wake-on-LAN to first port on 82576 ET2 quad port NICs, as it is
only supported there.
Signed-off-by: Stefan Assmann <sassmann@redhat.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add missing sg_init_table for sg_set_buf in virtio_net which
induced in defer skb patch.
Reported-by: Thomas Müller <thomas@mathtm.de>
Tested-by: Thomas Müller <thomas@mathtm.de>
Signed-off-by: Shirley Ma <xma@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit 2626419a.

It causes regressions for people with IGB cards.  Connection
requests don't complete etc.  The true cause of the issue is
still not known, but we should sort this out in net-next-2.6
not net-2.6
Signed-off-by: David S. Miller <davem@davemloft.net>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  IB/mlx4: Check correct variable for allocation failure
  RDMA/nes: Correct cap.max_inline_data assignment in nes_query_qp()
  RDMA/cm: Set num_paths when manually assigning path records
  IB/cm: Fix device_create() return value check

* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
  [S390] Update default configuration.
  [S390] nss: add missing .previous statement to asm function
  [S390] increase default size of vmalloc area
  [S390] s390: disable change bit override
  [S390] fix io_return critical section cleanup
  [S390] sclp_async: potential buffer overflow
  [S390] arch/s390/kernel: Add missing unlock

* 'for-linus' of git://git.kernel.dk/linux-2.6-block: (34 commits)
  cfq-iosched: Fix the incorrect timeslice accounting with forced_dispatch
  loop: Update mtime when writing using aops
  block: expose the statistics in blkio.time and blkio.sectors for the root cgroup
  backing-dev: Handle class_create() failure
  Block: Fix block/elevator.c elevator_get() off-by-one error
  drbd: lc_element_by_index() never returns NULL
  cciss: unlock on error path
  cfq-iosched: Do not merge queues of BE and IDLE classes
  cfq-iosched: Add additional blktrace log messages in CFQ for easier debugging
  i2o: Remove the dangerous kobj_to_i2o_device macro
  block: remove 16 bytes of padding from struct request on 64bits
  cfq-iosched: fix a kbuild regression
  block: make CONFIG_BLK_CGROUP visible
  Remove GENHD_FL_DRIVERFS
  block: Export max number of segments and max segment size in sysfs
  block: Finalize conversion of block limits functions
  block: Fix overrun in lcm() and move it to lib
  vfs: improve writeback_inodes_wb()
  paride: fix off-by-one test
  drbd: fix al-to-on-disk-bitmap for 4k logical_block_size
  ...

* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (29 commits)
  drm/nouveau: bail out of auxch transaction if we repeatedly recieve defers
  drm/nv50: implement gpio set/get routines
  drm/nv50: parse/use some more de-magiced parts of gpio table entries
  drm/nouveau: store raw gpio table entry in bios gpio structs
  drm/nv40: Init some tiling-related PGRAPH state.
  drm/nv50: Add NVA3 support in ctxprog/ctxvals generator.
  drm/nv50: another dodgy DP hack
  drm/nv50: punt hotplug irq handling out to workqueue
  drm/nv50: preserve an unknown SOR_MODECTRL value for DP encoders
  drm/nv50: Allow using the NVA3 new compute class.
  drm/nv50: cleanup properly if PDISPLAY init fails
  drm/nouveau: fixup the init failure paths some more
  drm/nv50: fix instmem init on IGPs if stolen mem crosses 4GiB mark
  drm/nv40: add LVDS table quirk for Dell Latitude D620
  drm/nv40: rework lvds table parsing
  drm/nouveau: detect vram amount once, and save the value
  drm/nouveau: remove some unused members from drm_nouveau_private
  drm/nouveau: Make use of TTM busy_placements.
  drm/nv50: add more 0x100c80 flushy magic
  drm/nv50: fix fbcon when framebuffer above 4GiB mark
  ...

The current algorithm will sometimes "detect" that
more chains are enabled than are really present in
the device because, for unknown reasons, the ucode
sends up all-zeroes signal values.

The simplest way of solving this is to restrict the
active chains mask to the chains we know are really
present on the device.

This fixes a bug with some devices where, since sometimes
more chains are enabled than really present, the system would hang.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

radix_tree_tag_get() is not safe to use concurrently with radix_tree_tag_set()
or radix_tree_tag_clear().  The problem is that the double tag_get() in
radix_tree_tag_get():

		if (!tag_get(node, tag, offset))
			saw_unset_tag = 1;
		if (height == 1) {
			int ret = tag_get(node, tag, offset);

may see the value change due to the action of set/clear.  RCU is no protection
against this as no pointers are being changed, no nodes are being replaced
according to a COW protocol - set/clear alter the node directly.

The documentation in linux/radix-tree.h, however, says that
radix_tree_tag_get() is an exception to the rule that "any function modifying
the tree or tags (...) must exclude other modifications, and exclude any
functions reading the tree".

The problem is that the next statement in radix_tree_tag_get() checks that the
tag doesn't vary over time:

			BUG_ON(ret && saw_unset_tag);

This has been seen happening in FS-Cache:

	https://www.redhat.com/archives/linux-cachefs/2010-April/msg00013.html

To this end, remove the BUG_ON() from radix_tree_tag_get() and note in various
comments that the value of the tag may change whilst the RCU read lock is held,
and thus that the return value of radix_tree_tag_get() may not be relied upon
unless radix_tree_tag_set/clear() and radix_tree_delete() are excluded from
running concurrently with it.
Reported-by: Romain DEGEZ <romain.degez@smartjog.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

As suggested by Linus, fix up kmem_ptr_validate() to handle non-kernel pointers
more graciously. The patch changes kmem_ptr_validate() to use the newly
introduced kern_ptr_validate() helper to check that a pointer is a valid kernel
pointer before we attempt to convert it into a 'struct page'.

Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Nick Piggin <npiggin@suse.de>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Christoph Lameter <cl@linux-foundation.org>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

As suggested by Linus, introduce a kern_ptr_validate() helper that does some
sanity checks to make sure a pointer is a valid kernel pointer.  This is a
preparational step for fixing SLUB kmem_ptr_validate().

Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Nick Piggin <npiggin@suse.de>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This reverts commit ba168fc3.

It changes user-visible sysfs interfaces, and breaks some existing user
space applications which apparently rely on the fact that the output
does not contain the "0x" prefix.
Requested-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

The savesys_ipl_nss asm function is put into the .init.text section
however it is missing a ".previous" section which would restore the
previous section.
Luckily all functions in early.c are init functions so it doesn't
matter currently.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

The default size of the vmalloc area is currently 1 GB. The memory resource
controller uses about 10 MB of vmalloc space per gigabyte of memory. That
turns a system with more than ~100 GB memory unbootable with the default
vmalloc size. It costs us nothing to increase the default size to some
more adequate value, e.g. 128 GB.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

commit 6a985c61
([S390] s390: use change recording override for kernel mapping)
deactivated the change bit recording for the kernel mapping to
improve the performance. This works most of the time, but there
are cases (e.g. kernel runs in home space, futex atomic compare xcmg)
where we modify user memory with the kernel mapping instead of the
user mapping.
Instead of fixing these cases, this patch just deactivates change bit
override to avoid future problems with other kernel code that might
use the kernel mapping for user memory.

CC: stable@kernel.org
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

If a machine check interrupts the io interrupt handler on one of the
instructions between io_return and io_leave the critical section
cleanup code will move the return psw to io_work_loop. By doing that
the switch from the asynchronous interrupt stack to the process stack
is skipped. If e.g. TIF_NEED_RESCHED is set things break because
the scheduler is called with the asynchronous interrupts stack.
Moving the psw back to io_return instead fixes the problem.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

"len" hasn't been properly range checked so we shouldn't use it as an
array offset.  This can only be written to by root but it would still be
annoying to accidentally write more than 3 characters and corrupt your
memory.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

In the default case the lock is not unlocked.  The return is
converted to a goto, to share the unlock at the end of the function.

A simplified version of the semantic patch that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@r exists@
expression E1;
identifier f;
@@

f (...) { <+...
* spin_lock_irq (E1,...);
... when != E1
* return ...;
...+> }
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

When CFQ dispatches requests forcefully due to a barrier or changing iosched,
it runs through all cfqq's dispatching requests and then expires each queue.
However, it does not activate a cfqq before flushing its IOs resulting in
using stale values for computing slice_used.
This patch fixes it by calling activate queue before flushing reuqests from
each queue.

This is useful mostly for barrier requests because when the iosched is changing
it really doesnt matter if we have incorrect accounting since we're going to
break down all structures anyway.

We also now expire the current timeslice before moving on with the dispatch
to accurately account slice used for that cfqq.

Signed-off-by: Divyesh Shah<dpshah@google.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>

* 'nouveau/for-airlied' of ../drm-nouveau-next: (21 commits)
  drm/nouveau: bail out of auxch transaction if we repeatedly recieve defers
  drm/nv50: implement gpio set/get routines
  drm/nv50: parse/use some more de-magiced parts of gpio table entries
  drm/nouveau: store raw gpio table entry in bios gpio structs
  drm/nv40: Init some tiling-related PGRAPH state.
  drm/nv50: Add NVA3 support in ctxprog/ctxvals generator.
  drm/nv50: another dodgy DP hack
  drm/nv50: punt hotplug irq handling out to workqueue
  drm/nv50: preserve an unknown SOR_MODECTRL value for DP encoders
  drm/nv50: Allow using the NVA3 new compute class.
  drm/nv50: cleanup properly if PDISPLAY init fails
  drm/nouveau: fixup the init failure paths some more
  drm/nv50: fix instmem init on IGPs if stolen mem crosses 4GiB mark
  drm/nv40: add LVDS table quirk for Dell Latitude D620
  drm/nv40: rework lvds table parsing
  drm/nouveau: detect vram amount once, and save the value
  drm/nouveau: remove some unused members from drm_nouveau_private
  drm/nouveau: Make use of TTM busy_placements.
  drm/nv50: add more 0x100c80 flushy magic
  drm/nv50: fix fbcon when framebuffer above 4GiB mark
  ...

There's one known case where we never stop recieving DEFER, and loop here
forever.  Lets not do that..
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

And use our own version of the GPIO table for the INIT_GPIO opcode.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>