- 23 Apr, 2020 38 commits
-
-
Grygorii Strashko authored
Now spinlock is used to synchronize everything which is not required. Add mutex and use to sync access to PTP interface and PTP worker and use spinlock only to sync FIFO/events processing. Signed-off-by:
Grygorii Strashko <grygorii.strashko@ti.com> Acked-by:
Richard Cochran <richardcochran@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Grygorii Strashko authored
Now the tx timestamp processing happens from different contexts - softirq and thread/PTP worker. Enabling IRQ will add one more hard_irq context. This makes over all defered TX timestamp processing and locking overcomplicated. Move tx timestamp processing to PTP worker always instead. napi_rx->cpts_tx_timestamp if ptp_packet then push to txq ptp_schedule_worker() do_aux_work->cpts_overflow_check cpts_process_events() Signed-off-by: -
Grygorii Strashko authored
Now the CPTS driver performs packet (skb) parsing every time when it needs to match packet to CPTS event (including ptp_classify_raw() calls). This patch optimizes matching process by parsing packet only once upon arrival and stores PTP specific data in skb->cb using the same fromat as in CPTS HW event. As result, all future matching reduces to comparing two u32 values. Signed-off-by:
-
Grygorii Strashko authored
The CPTS HW latches and saves CPTS counter value in CPTS fifo immediately after writing to CPSW_CPTS_PUSH.TS_PUSH (bit 0), so the total time that the driver needs to read the CPTS timestamp is the time required CPSW_CPTS_PUSH write to actually reach HW. Hence switch CPTS driver to implement new .gettimex64() callback for more precise measurement of the offset between a PHC and the system clock which is measured as time between write(CPSW_CPTS_PUSH) read(CPSW_CPTS_PUSH) Signed-off-by:
-
Grygorii Strashko authored
Now CPTS driver .adjfreq() generates request to read CPTS current time (CPTS_EV_PUSH) with intention to process all pending event using previous frequency adjustment values before switching to the new ones. So CPTS_EV_PUSH works as a marker to switch to the new frequency adjustment values. Current code assumes that all job is done in .adjfreq(), but after enabling IRQ this will not be true any more. Hence save new frequency adjustment values (mult) and perform actual freq adjustment in cpts_fifo_read() immediately after CPTS_EV_PUSH is received. Signed-off-by:
-
Grygorii Strashko authored
Now CPTS HW time reading code is implemented in timecounter->cyclecounter .read() callback and performs following operations: timecounter_read() ->cc.read() -> cpts_systim_read() - request current CPTS HW time CPTS_TS_PUSH.TS_PUSH = 1 - poll CPTS FIFO for CPTS_EV_PUSH event with current HW timestamp This approach need to be changed for the future switch to PTP PHC .gettimex64() callback, which require to separate requesting current CPTS HW time and processing CPTS FIFO. And for the follow up patch, which improves .adjfreq() implementation. This patch moves code accessing CPTS HW out of timecounter code as following: - convert HW timestamp of every CPTS event to PTP time (us) and store it as part struct cpts_event; - add CPTS context field to store current CPTS HW time (counter) value and update it on CPTS_EV_PUSH reception; - move code accessing CPTS HW out of timecounter code and use current CPTS HW time (counter) from CPTS context instead; - ensure timecounter->cycle_last is updated on CPTS_EV_PUSH reception. After this change CPTS timecounter will only perform timekeeper role without actually accessing CPTS HW. Signed-off-by:
-
Grygorii Strashko authored
Use dev_yy() API instead of pr_yy() for log outputs. Signed-off-by:
-
David S. Miller authored
Eric Dumazet says: ==================== net: napi: addition of napi_defer_hard_irqs This patch series augments gro_glush_timeout feature with napi_defer_hard_irqs As extensively described in first patch changelog, this can suppresss the chit-chat traffic between NIC and host to signal interrupts and re-arming them, since this can be an issue on high speed NIC with many queues. The last patch in this series converts mlx4 TX completion to napi_complete_done(), to enable this new mechanism. ==================== Signed-off-by: -
Eric Dumazet authored
In order to benefit from the new napi_defer_hard_irqs feature, we need to use napi_complete_done() variant in this driver. RX path is already using it, this patch implements TX completion side. mlx4_en_process_tx_cq() now returns the amount of retired packets, instead of a boolean, so that mlx4_en_poll_tx_cq() can pass this value to napi_complete_done(). Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Eric Dumazet authored
gro_flush_timeout and napi_defer_hard_irqs can be read from napi_complete_done() while other cpus write the value, whithout explicit synchronization. Use READ_ONCE()/WRITE_ONCE() to annotate the races. Signed-off-by:
-
Eric Dumazet authored
Back in commit 3b47d303 ("net: gro: add a per device gro flush timer") we added the ability to arm one high resolution timer, that we used to keep not-complete packets in GRO engine a bit longer, hoping that further frames might be added to them. Since then, we added the napi_complete_done() interface, and commit 364b6055 ("net: busy-poll: return busypolling status to drivers") allowed drivers to avoid re-arming NIC interrupts if we made a promise that their NAPI poll() handler would be called in the near future. This infrastructure can be leveraged, thanks to a new device parameter, which allows to arm the napi hrtimer, instead of re-arming the device hard IRQ. We have noticed that on some servers with 32 RX queues or more, the chit-chat between the NIC and the host caused by IRQ delivery and re-arming could hurt throughput by ~20% on 100Gbit NIC. In contrast, hrtimers are using local (percpu) resources and might have lower cost. The new tunable, named napi_defer_hard_irqs, is placed in the same hierarchy than gro_flush_timeout (/sys/class/net/ethX/) By default, both gro_flush_timeout and napi_defer_hard_irqs are zero. This patch does not change the prior behavior of gro_flush_timeout if used alone : NIC hard irqs should be rearmed as before. One concrete usage can be : echo 20000 >/sys/class/net/eth1/gro_flush_timeout echo 10 >/sys/class/net/eth1/napi_defer_hard_irqs If at least one packet is retired, then we will reset napi counter to 10 (napi_defer_hard_irqs), ensuring at least 10 periodic scans of the queue. On busy queues, this should avoid NIC hard IRQ, while before this patch IRQ avoidance was only possible if napi->poll() was exhausting its budget and not call napi_complete_done(). This feature also can be used to work around some non-optimal NIC irq coalescing strategies. Having the ability to insert XX usec delays between each napi->poll() can increase cache efficiency, since we increase batch sizes. It also keeps serving cpus not idle too long, reducing tail latencies. Co-developed-by:
Luigi Rizzo <lrizzo@google.com> Signed-off-by:
-
David S. Miller authored
Sudarsana Reddy Kalluru says: ==================== qed*: Add support for pcie advanced error recovery. The patch series adds qed/qede driver changes for PCIe Advanced Error Recovery (AER) support. Patch (1) adds qed changes to enable the device to send error messages to root port when detected. Patch (2) adds qede support for handling the detected errors (AERs). Changes from previous version: ------------------------------- v2: use pci_num_vf() instead of caching the value in edev. ==================== Signed-off-by: -
Sudarsana Reddy Kalluru authored
The error recovery is handled by management firmware (MFW) with the help of qed/qede drivers. Upon detecting the errors, driver informs MFW about this event which in turn starts a recovery process. MFW sends ERROR_RECOVERY notification to the driver which performs the required cleanup/recovery from the driver side. Signed-off-by:
Sudarsana Reddy Kalluru <skalluru@marvell.com> Acked-by:
Jakub Kicinski <kuba@kernel.org> Signed-off-by:
-
Sudarsana Reddy Kalluru authored
The patch enables the device to send error messages to root port when an error is detected. Signed-off-by:
Ariel Elior <aelior@marvell.com> Signed-off-by:
Igor Russkikh <irusskikh@marvell.com> Signed-off-by:
-
Alexander Lobakin authored
gro_cells lib is used by different encapsulating netdevices, such as geneve, macsec, vxlan etc. to speed up decapsulated traffic processing. CPU tag is a sort of "encapsulation", and we can use the same mechs to greatly improve overall DSA performance. skbs are passed to the GRO layer after removing CPU tags, so we don't need any new packet offload types as it was firstly proposed by me in the first GRO-over-DSA variant [1]. The size of struct gro_cells is sizeof(void *), so hot struct dsa_slave_priv becomes only 4/8 bytes bigger, and all critical fields remain in one 32-byte cacheline. The other positive side effect is that drivers for network devices that can be shipped as CPU ports of DSA-driven switches can now use napi_gro_frags() to pass skbs to kernel. Packets built that way are completely non-linear and are likely being dropped without GRO. This was tested on to-be-mainlined-soon Ethernet driver that uses napi_gro_frags(), and the overall performance was on par with the variant from [1], sometimes even better due to minimal overhead. net.core.gro_normal_batch tuning may help to push it to the limit on particular setups and platforms. iperf3 IPoE VLAN NAT TCP forwarding (port1.218 -> port0) setup on 1.2 GHz MIPS board: 5.7-rc2 baseline: [ID] Interval Transfer Bitrate Retr [ 5] 0.00-120.01 sec 9.00 GBytes 644 Mbits/sec 413 sender [ 5] 0.00-120.00 sec 8.99 GBytes 644 Mbits/sec receiver Iface RX packets TX packets eth0 7097731 7097702 port0 426050 6671829 port1 6671681 425862 port1.218 6671677 425851 With this patch: [ID] Interval Transfer Bitrate Retr [ 5] 0.00-120.01 sec 12.2 GBytes 870 Mbits/sec 122 sender [ 5] 0.00-120.00 sec 12.2 GBytes 870 Mbits/sec receiver Iface RX packets TX packets eth0 9474792 9474777 port0 455200 353288 port1 9019592 455035 port1.218 353144 455024 v2: - Add some performance examples in the commit message; - No functional changes. [1] https://lore.kernel.org/netdev/20191230143028.27313-1-alobakin@dlink.ru/Signed-off-by:
Alexander Lobakin <bloodyreaper@yandex.ru> Signed-off-by:
-
Fernando Gont authored
RFC4862 5.5.3 e) prevents received Router Advertisements from reducing the Valid Lifetime of configured addresses to less than two hours, thus preventing hosts from reacting to the information provided by a router that has positive knowledge that a prefix has become invalid. This patch makes hosts honor all Valid Lifetime values, as per draft-gont-6man-slaac-renum-06, Section 4.2. This is meant to help mitigate the problem discussed in draft-ietf-v6ops-slaac-renum. Note: Attacks aiming at disabling an advertised prefix via a Valid Lifetime of 0 are not really more harmful than other attacks that can be performed via forged RA messages, such as those aiming at completely disabling a next-hop router via an RA that advertises a Router Lifetime of 0, or performing a Denial of Service (DoS) attack by advertising illegitimate prefixes via forged PIOs. In scenarios where RA-based attacks are of concern, proper mitigations such as RA-Guard [RFC6105] [RFC7113] should be implemented. Signed-off-by:
Fernando Gont <fgont@si6networks.com> Signed-off-by:
-
David S. Miller authored
Ioana Ciornei says: ==================== dpaa2-eth: add support for xdp bulk enqueue The first patch moves the DEV_MAP_BULK_SIZE macro into the xdp.h header file so that drivers can take advantage of it and use it. The following 3 patches are there to setup the scene for using the bulk enqueue feature. First of all, the prototype of the enqueue function is changed so that it returns the number of enqueued frames. Second, the bulk enqueue interface is used but without any functional changes, still one frame at a time is enqueued. Third, the .ndo_xdp_xmit callback is split into two stages, create all FDs for the xdp_frames received and then enqueue them. The last patch of the series builds on top of the others and instead of issuing an enqueue operation for each FD it issues a bulk enqueue call for as many frames as possible. This is repeated until all frames are enqueued or the maximum number of retries is hit. We do not use the XDP_XMIT_FLUSH flag since the architecture is not capable to store all frames dequeued in a NAPI cycle, instead we send out right away all frames received in a .ndo_xdp_xmit call. Changes in v2: - statically allocate an array of dpaa2_fd by frame queue - use the DEV_MAP_BULK_SIZE as the maximum number of xdp_frames received in .ndo_xdp_xmit() ==================== Signed-off-by: -
Ioana Ciornei authored
Take advantage of the bulk enqueue feature in .ndo_xdp_xmit. We cannot use the XDP_XMIT_FLUSH since the architecture is not capable to store all the frames dequeued in a NAPI cycle so we instead are enqueueing all the frames received in a ndo_xdp_xmit call right away. After setting up all FDs for the xdp_frames received, enqueue multiple frames at a time until all are sent or the maximum number of retries is hit. Signed-off-by:
Ioana Ciornei <ioana.ciornei@nxp.com> Acked-by:
Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by:
-
Ioana Ciornei authored
Instead of having a function that both creates a frame descriptor from an xdp_frame and enqueues it, split this into two stages. Add the dpaa2_eth_xdp_create_fd that just transforms an xdp_frame into a FD while the actual enqueue callback is called directly from the ndo for each frame. This is particulary useful in conjunction with bulk enqueue. Signed-off-by:
-
Ioana Ciornei authored
Update the dpaa2-eth driver to use the bulk enqueue function introduced with the change to QBMAN ring mode. At the moment, no functional changes are made but rather the driver just transitions to the new interface while still enqueuing just one frame at a time. Signed-off-by:
-
Ioana Ciornei authored
The enqueue dpaa2-eth callback now returns the number of successfully enqueued frames. This is a preliminary patch necessary for adding support for bulk ring mode enqueue. Signed-off-by:
-
Ioana Ciornei authored
Export the DEV_MAP_BULK_SIZE macro to the header file so that drivers can directly use it as the maximum number of xdp_frames received in the .ndo_xdp_xmit() callback. Signed-off-by:
-
David Ahern authored
Add nodad when adding IPv6 addresses and remove the sleep. A recent change to iproute2 moved the 'pref medium' to the prefix (where it belongs). Change the expected route check to strip 'pref medium' to be compatible with old and new iproute2. Add IPv4 runtime test with an IPv6 address as the gateway in the default route. Signed-off-by:
David Ahern <dsahern@gmail.com> Signed-off-by:
-
David S. Miller authored
Petr Machata says: ==================== Add selftests for pedit ex munge ip6 dsfield Patch #1 extends the existing generic forwarding selftests to cover pedit ex munge ip6 traffic_class as well. Patch #2 adds TDC test coverage. ==================== Signed-off-by: -
Petr Machata authored
Add a self-test for the IPv6 dsfield munge that iproute2 will support. Signed-off-by:
Petr Machata <petrm@mellanox.com> Signed-off-by:
-
Petr Machata authored
Extend the pedit_dsfield forwarding selftest with coverage of "pedit ex munge ip6 dsfield set". Signed-off-by:
-
David S. Miller authored
Oleksij Rempel says: ==================== add TJA1102 support changes v5: - rename __of_mdiobus_register_phy() to of_mdiobus_phy_device_register() changes v4: - remove unused phy_id variable changes v3: - export part of of_mdiobus_register_phy() and reuse it in tja11xx driver - coding style fixes changes v2: - use .match_phy_device - add irq support - add add delayed registration for PHY1 ==================== Signed-off-by: -
Oleksij Rempel authored
TJA1102 is a dual PHY package with PHY0 having proper PHYID and PHY1 having no ID. On one hand it is possible to for PHY detection by compatible, on other hand we should be able to reset complete chip before PHY1 configured it, and we need to define dependencies for proper power management. We can solve it by defining PHY1 as child of PHY0: tja1102_phy0: ethernet-phy@4 { reg = <0x4>; interrupts-extended = <&gpio5 8 IRQ_TYPE_LEVEL_LOW>; reset-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>; reset-assert-us = <20>; reset-deassert-us = <2000>; tja1102_phy1: ethernet-phy@5 { reg = <0x5>; interrupts-extended = <&gpio5 8 IRQ_TYPE_LEVEL_LOW>; }; }; The PHY1 should be a subnode of PHY0 and registered only after PHY0 was completely reset and initialized. Signed-off-by:Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
Oleksij Rempel authored
This function will be needed in tja11xx driver for secondary PHY support. Signed-off-by:
-
Oleksij Rempel authored
TJA1102 is an dual T1 PHY chip. Both PHYs are separately addressable. Both PHYs are similar but have different amount of functionality. For example PHY 1 has no PHY ID and no health monitor. Signed-off-by:
-
Oleksij Rempel authored
Document the NXP TJA11xx PHY bindings. Signed-off-by:
-
Tang Bin authored
Use IS_ERR() and PTR_ERR() instead of PTR_ZRR_OR_ZERO() to simplify code, avoid redundant paramenter definitions and judgements. Signed-off-by:
Zhang Shengju <zhangshengju@cmss.chinamobile.com> Signed-off-by:
Tang Bin <tangbin@cmss.chinamobile.com> Signed-off-by:
-
Oleksij Rempel authored
Add support for following phy-modes: rgmii, rgmii-id, rgmii-txid, rgmii-rxid. This PHY has an internal RX delay of 1.2ns and no delay for TX. The pad skew registers allow to set the total TX delay to max 1.38ns and the total RX delay to max of 2.58ns (configurable 1.38ns + build in 1.2ns) and a minimal delay of 0ns. According to the RGMII v1.3 specification the delay provided by PCB traces should be between 1.5ns and 2.0ns. The RGMII v2.0 allows to provide this delay by MAC or PHY. So, we configure this PHY to the best values we can get by this HW: TX delay to 1.38ns (max supported value) and RX delay to 1.80ns (best calculated delay) The phy-modes can still be fine tuned/overwritten by *-skew-ps device tree properties described in: Documentation/devicetree/bindings/net/micrel-ksz90x1.txt Signed-off-by:
Philippe Schenker <philippe.schenker@toradex.com> Reviewed-by:
-
Jason Yan authored
Fix the following coccicheck warning: net/caif/caif_dev.c:410:2-13: WARNING: Assignment of 0/1 to bool variable net/caif/caif_dev.c:445:2-13: WARNING: Assignment of 0/1 to bool variable net/caif/caif_dev.c:145:1-12: WARNING: Assignment of 0/1 to bool variable net/caif/caif_dev.c:223:1-12: WARNING: Assignment of 0/1 to bool variable Signed-off-by:
Jason Yan <yanaijie@huawei.com> Signed-off-by:
-
Chuah, Kim Tatt authored
For dwmac4, enable VLAN promiscuity when MAC controller is requested to enter promiscuous mode. Signed-off-by:
Chuah, Kim Tatt <kim.tatt.chuah@intel.com> Signed-off-by:
Ong Boon Leong <boon.leong.ong@intel.com> Signed-off-by:
Tan, Tee Min <tee.min.tan@intel.com> Signed-off-by:
Wong Vee Khee <vee.khee.wong@intel.com> Signed-off-by:
-
Wei Yongjun authored
macvlan_hash_lookup() uses list_for_each_entry_rcu() for traversing should either under RCU in fast path or the protection of rtnl_mutex. In the case of holding RTNL, we should add the corresponding lockdep expression to silence the following false-positive warning: ============================= WARNING: suspicious RCU usage 5.7.0-rc1-next-20200416-00003-ga3b8d28bc #1 Not tainted ----------------------------- drivers/net/macvlan.c:126 RCU-list traversed in non-reader section!! Signed-off-by:
Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by:
-
David Ahern authored
Add tests for vrf and xfrms with a second round after adding a qdisc. There are a few known problems documented with the test cases that fail. The fix is non-trivial; will come back to it when time allows. Signed-off-by:
-
Xiaoliang Yang authored
Right now it can be seen that the VSC9959 (Felix) switch will not flood frames if they have a VLAN tag with a PCP of 1-7 (nonzero). It turns out that Felix is quite different from its cousin, Ocelot, in that frame flooding can be allowed/denied per traffic class. Where Ocelot has 1 instance of the ANA_FLOODING register, Felix has 8. The approach that this driver is going to take is "thanks, but no thanks". We have no use case of limiting the flooding domain based on traffic class, so we just want to allow packets to be flooded, no matter what traffic class they have. So we copy the line of code from ocelot.c which does the one-shot initialization of the flooding PGIDs, and we add it to felix.c as well - except replicated 8 times. Signed-off-by:
Xiaoliang Yang <xiaoliang.yang_1@nxp.com> Signed-off-by:
Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by:
-
- 22 Apr, 2020 2 commits
-
-
Manivannan Sadhasivam authored
Add tracepoint support for QRTR with NS as the first candidate. Later on this can be extended to core QRTR and transport drivers. The trace_printk() used in NS has been replaced by tracepoints. Signed-off-by:
Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by:
-
YueHaibing authored
net/ipv6/ila/ila_xlat.c:604:0: warning: macro "ILA_HASH_TABLE_SIZE" is not used [-Wunused-macros] Signed-off-by:
YueHaibing <yuehaibing@huawei.com> Signed-off-by:
-
