- 14 Mar, 2022 13 commits
-
-
Ville Syrjälä authored
The DRRS code has no use for the intel_dp, replace it with just a crtc pointer. This is just an intermediate step towards making DRRS truly per-crtc. Signed-off-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220311172428.14685-12-ville.syrjala@linux.intel.comReviewed-by:
Jani Nikula <jani.nikula@intel.com>
-
Ville Syrjälä authored
Add helper to get the drrs type as a string, and use it in a couple of places. Also pimp the debugfs output a bit while at it. Signed-off-by:
-
Ville Syrjälä authored
Add a helper to determine which type of DRRS the panel supports. Signed-off-by:
-
Ville Syrjälä authored
There are a couple of cases where we essentially just want to get/check the preferred fixed mode of the panel. Add a small helper for that to abstract away the direct pointer lookup. Signed-off-by:
-
Ville Syrjälä authored
Several connectors want to return the fixed_mode from .get_modes(), add a helper to do that (and hide the details inside intel_panel.c). Signed-off-by:
-
Ville Syrjälä authored
Abstract away the details on where we store the fixed/downclock modes, and also how we select them. Will be useful for static DRRS (aka. allowing the user to select the refresh rate for the panel). We pass in the user requested mode to intel_panel_fixed_mode() so that in the future it may try to match the refresh rate. And intel_panel_downclock_mode() gets passed the adjusted_mode we actually chose to use so that it may find a suitable lower resresh rate variant. v2: Hook it up for all encoders s/fixed_mode/adjusted_mode/ in intel_panel_downclock_mode() (Jani) Elaborate on the choice or arguments for the functions (Jani) Signed-off-by: -
Ville Syrjälä authored
When we found a downclock mode dev_priv->drrs.type is just a straight copy of dev_priv->vbt.drrs_type. And in case we couldn't find a downclock mode can_enable_drrs() won't let us enable DRRS anyway so the minor distinction between the two is irrelevant. So let's just nuke dev_priv->drrs.type and consult the VBT version directly. Signed-off-by:
-
Ville Syrjälä authored
No need for all this connector type special casing. If the connector has a fixed mode just print it, otherwise don't. Signed-off-by:
-
Ville Syrjälä authored
We want to eventually get rid of the connector->panel.fixed_mode pointer so avoid using it during LVDS setup. Since this all happens during the encoder init we already have the fixed_mode around, just pass that in. Signed-off-by:
-
Ville Syrjälä authored
We want to stop using connector->panel.fixed_mode directtly. In order to look it up in the future we'll need to have the requested mode around, so pass that in fully (instead of just passing bits of it). Signed-off-by:
-
Ville Syrjälä authored
We want to eventually get rid of the connector->panel.fixed_mode pointer so avoid using it during DSI property setup. Since this all happens during the encoder init we already have the fixed_mode around, just pass that in. Signed-off-by:
-
José Roberto de Souza authored
Up to now alderlake-p was using the same eDP voltage swing table for frequencies up to HBR2 as icelake but now it has its own table. BSpec: 49291 Cc: Clinton A Taylor <clinton.a.taylor@intel.com> Signed-off-by:
José Roberto de Souza <jose.souza@intel.com> Reviewed-by:
Matt Roper <matthew.d.roper@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220314152753.85081-1-jose.souza@intel.com
-
Jani Nikula authored
early-quirks.c is the only user of drm/i915_drm.h that also needs drm/i915_pciids.h. Include the masses of PCI ID macros only where needed. Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: linux-pci@vger.kernel.org Cc: x86@kernel.org Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220311100639.114685-1-jani.nikula@intel.com
-
- 10 Mar, 2022 17 commits
-
-
Ville Syrjälä authored
Rename the PIPECONF refresh rate select bits to be less cryptic. Also nothing eDP specific about these as they also select between FP0 vs. FP1 for the DPLL and thus can be used to change the refresh rate on other output types as well. Signed-off-by:
-
Ville Syrjälä authored
Make the DRRS refresh rate enum less magical. Signed-off-by:
-
Ville Syrjälä authored
Make the drrs type enum less convoluted. Signed-off-by:
-
Ville Syrjälä authored
Grab the DRRS MSA timing delay value from the VBT and program things accordingly. Only ilk/snb/ivb have this so presumably on hsw+ we don't need it. Signed-off-by:
-
Ville Syrjälä authored
VBT hsa a field for the MSA timing delay, which supposedly should be used with DRRS. Extract the data from the VBT. Signed-off-by:
-
Ville Syrjälä authored
Use the standard [CONNECTOR:%d:%s] format in the DRRS debugs. Signed-off-by:
-
Ville Syrjälä authored
Pass the fixed_mode as const to intel_drrs_init() since it's not supposed to mutate the mode. Signed-off-by:
-
Ville Syrjälä authored
Only seamless DRRS needs the frontbuffer tracking, so check for that. Also use != consistently instead of randomly picking < as the comparison operator. Signed-off-by:
-
Ville Syrjälä authored
struct dp_link_dpll is a pointless wrapper around struct dpll. Just store the desired link rate into struct dpll::dot and we're done. v2: Document the full divider as a proper decimal number on chv Nuke bogus eDP 1.4 comments for chv while at it Signed-off-by: -
Ville Syrjälä authored
Set the bxt/glk DPLL min dotclock to 25MHz (HDMI minimum) and the max to 594 MHz (HDMI max). The supported DP frequencies (162MHz-540MHz) fit within the same range. Signed-off-by:
-
Ville Syrjälä authored
Use chv_calc_dpll_params() to calculate the BXT DP DPLL VCO frequency. We need to add the m1 divider into bxt_dp_clk_val[] for this to work. v2: Make the WARN_ON() sensible Signed-off-by:
-
Ville Syrjälä authored
bxt_clk_div is basically the same as struct dpll. Just use the latter. Reviewed-by:
-
Ville Syrjälä authored
Get rid of the pointless m2 int vs. frac split in bxt_clk_div and just store the whole divider as one. v2: Document the full divider as a proper decimal number Signed-off-by:
-
Ville Syrjälä authored
Use REG_BIT() & co. for bxt/glk PLL registers. v2: Reorder a few bits for consistency Signed-off-by:
-
Ville Syrjälä authored
Remove the comment specifying the exact formulat for calculating the DPLL frequency from the *_find_best_dpll() functions. Each platform variant has its own way to calculate these and we have the code already to do that. These comments are entirely redundant and often even wrong so just get rid of them. Signed-off-by:
-
Ville Syrjälä authored
Unify vlv/chv with earlier platforms so that the sturct dpll::dot represents the /5 clock frequency (ie. DP symbol rate or HDMI TMDS rate) rather than the *5 fast clock (/2 of the bitrate). Makes life a little less confusing to get the same number back in .dot which we fed into the DPLL algorithm. v2: Actually just include the 5x in the final P divider Do the same change to the hand rolled gvt code v3: Missed a few *5 in *_find_best_dpll() Reviewed-by: -
Ville Syrjälä authored
When using bigjoiner it's useful to know the offset of each individual pipe in the whole set of joined pipes. Let's include that information in our PIPESRC rectangle. With this we can make the plane clipping code blissfully unaware of bigjoiner usage, as all we have to do is remove the pipe's offset from the final plane destination coordinates. v2: Use intel_bigjoiner_num_pipes() Signed-off-by:
Manasi Navare <manasi.d.navare@intel.com>
-
- 09 Mar, 2022 2 commits
-
-
Ville Syrjälä authored
GLK doesn't support SAGV, so with CNL gone there is no use for having a DISPLAY_VER==10 SAGV block time in the code. Signed-off-by:
Vinod Govindapillai <vinod.govindapillai@intel.com>
-
Changcheng Deng authored
Use min_t() in order to make code cleaner. Reported-by:
Zeal Robot <zealci@zte.com.cn> Signed-off-by:
Changcheng Deng <deng.changcheng@zte.com.cn> Signed-off-by:
-
- 07 Mar, 2022 2 commits
-
-
Jani Nikula authored
We have a helper for getting at the enclosing gmbus struct from the embedded i2c_adapter, use it. Signed-off-by:
-
Jani Nikula authored
Limit the scope. Suggested-by:
-
- 04 Mar, 2022 6 commits
-
-
Ville Syrjälä authored
Replace the hardcoded 2 pipe assumptions when we're massaging pipe_mode and the pipe_src rect to be suitable for bigjoiner. Instead we can just count the number of pipes in the bitmask. v2: Introduce intel_bigjoiner_num_pipes() Signed-off-by:
-
Ville Syrjälä authored
Since we now have the bigjoiner_pipes bitmask the boolean is redundant. Get rid of it. Also, populating bigjoiner_pipes already during encoder->compute_config() allows us to use it much earlier during the state calculation as well. The initial aim is to use it in intel_crtc_compute_config(). v2: Move the hweight(bigjoiner_pipes) stuff to a later patch Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com> #v1 Reviewed-by: Manasi Navare <manasi.d.navare@intel.com> #v1 Signed-off-by:
-
Ville Syrjälä authored
Instead of just having the pipe_src_{w,h} let's use a full drm_rect for it. This will be particularly useful to astract away some bigjoiner details. v2: No hweight() stuff yet Signed-off-by: -
Ville Syrjälä authored
Use designated initializers to make it clear what is what, and to decouple us from the specific ordering of the members. Signed-off-by:
-
Ville Syrjälä authored
Remove the pointless m2_frac_en from bxt_clk_div. Signed-off-by:
-
Ville Syrjälä authored
Use the simple '= {}' form to initialize empty arrays/structs. Also add some missing whitespace. Signed-off-by:
-
