- 29 Nov, 2016 22 commits
-
-
Larry Finger authored
In commit a5ffbe0a ("rtlwifi: Fix scheduling while atomic bug") and commit a269913c ("rtlwifi: Rework rtl_lps_leave() and rtl_lps_enter() to use work queue"), an error was introduced in the power-save routines due to the fact that leaving PS was delayed by the use of a work queue. This problem is fixed by detecting if the enter or leave routines are in interrupt mode. If so, the workqueue is used to place the request. If in normal mode, the enter or leave routines are called directly. Fixes: a269913c ("rtlwifi: Rework rtl_lps_leave() and rtl_lps_enter() to use work queue") Reported-by:
Ping-Ke Shih <pkshih@realtek.com> Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@vger.kernel.org> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org>
-
Anthony Romano authored
mt7601u_mac_stop_hw should stop polling the rxq once it remains empty but instead continues polling after the rxq status stays clear; bringing down the interface takes about six seconds from this alone. Speed up path by exiting rxq loop once status repeatedly polls empty. Signed-off-by:
Anthony Romano <anthony.romano@coreos.com> Reviewed-by:
Jakub Kicinski <kubakici@wp.pl> Signed-off-by:
-
Arend Van Spriel authored
The scan results for scheduled scan as retrieved from the device have changed. A field has been added which is not needed. However, the appended info is. Luckily they are versioned so check that to find out the location of the appended data. Reviewed-by:
Hante Meuleman <hante.meuleman@broadcom.com> Reviewed-by:
Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com> Reviewed-by:
Franky Lin <franky.lin@broadcom.com> Signed-off-by:
Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by:
-
Arend Van Spriel authored
User-space can specify the interval for the scheduled scan. This interval is found in scheduled scan plan. The driver supports only one plan, which is legacy behaviour. Reviewed-by:
-
Arend Van Spriel authored
In the .sched_scan_start() callback a condition was checked whether a normal scan was ongoing. However, there is no need for this check as it is ok to start the scheduled scan irrespective whether or not a normal scan is ongoing. Reviewed-by:
-
Arend Van Spriel authored
User-space can provide list of channels in the schedule scan request. This was ignored so all channels supported and allowed by the device were used. This patch configures the device to use the channels as listed in the request. Reviewed-by:
-
Arend Van Spriel authored
Rework .sched_scan_start() callback moving actual configuration of the device in pno source file. Reviewed-by:
-
Arend Van Spriel authored
The brcmf_pno_config() function handles two configurations in firmware. Split it and have caller sort out what is needed. Reviewed-by:
-
Arend Van Spriel authored
For scheduled scan we initiate an escan in firmware to obtain more info missing from the scheduled scan notification we get from firmware. For upcoming functionality this is also required so make it a bit more generic. Reviewed-by:
-
Arend Van Spriel authored
Reduce the number of parameters as the removed ones can be obtained through struct brcmf_if parameter. Reviewed-by:
-
Arend Van Spriel authored
The ssids list in the scheduled scan request were not properly taken into account when configuring in firmware. The hidden bit was set for any ssid resulting in active scanning for all. Only set it for ssids that are in the ssids list. Reviewed-by:
-
Arend Van Spriel authored
Introducing new source file for pno related functionality. Moving existing pno functions. Reviewed-by:
-
Arend Van Spriel authored
This chip was already supported, but seems a device came up giving a different chip identifier. So adding that effectively mapping to the same firmware file as for 43340 chip. Reviewed-by:
-
Franky Lin authored
In rev6 of pcie host dongle interface protocol, host needs to maximum supported ring number from dongle shared memory and set up ring buffer and ring indices offset accordingly. Reviewed-by:
-
Brian Norris authored
Marvell Wifi PCIe modules don't always behave nicely for PCIe power management when their firmware hasn't been loaded, particularly after suspending the PCIe link one or more times. When this happens, we might end up spinning forever in this status-polling tight loop. Let's make this less tight by adding a timeout and by sleeping a bit in between reads, as we do with the other similar loops. This prevents us from hogging a CPU even in such pathological cases, and allows the FW initialization to just fail gracefully instead. I chose the same polling parameters as the earlier loop in this function, and empirically, I found that this loop never makes it more than about 12 cycles in a sane FW init sequence. I had no official information on the actual intended latency for this portion of the download. Signed-off-by:
Brian Norris <briannorris@chromium.org> Acked-by:
Amitkumar Karwar <akarwar@marvell.com> Signed-off-by:
-
Kirtika Ruchandani authored
mwifiex_usb_probe() defines and sets bcd_usb but does not use it, Compiling with W=1 gives the following warning, fix it. mwifiex/usb.c: In function ‘mwifiex_usb_probe’: mwifiex/usb.c:383:41: warning: variable ‘bcd_usb’ set but not used [-Wunused-but-set-variable] The unused variable seems to be present since 4daffe35 which introduced mwifiex_usb_probe(). Fixes: 4daffe35 ("mwifiex: add support for Marvell USB8797 chipset") Cc: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by:
Kirtika Ruchandani <kirtika@google.com> Signed-off-by:
-
Kirtika Ruchandani authored
Commit 92263a84 introduced mwifiex_deaggr_sdio_pkt which initializes variable pkt_type but does not use it. Compiling with W=1 gives the following warning, fix it. mwifiex/sdio.c: In function ‘mwifiex_deaggr_sdio_pkt’: mwifiex/sdio.c:1198:6: warning: variable ‘pkt_type’ set but not used [-Wunused-but-set-variable] Fixes: 92263a84 ("mwifiex: add SDIO rx single port aggregation") Cc: Zhaoyang Liu <liuzy@marvell.com> Cc: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by:
-
Kirtika Ruchandani authored
mwifiex_sdio_resume() intializes pm_flag, just like mwifiex_sdio_suspend(), but does not use it. Compiling with W=1 gives the following warning, fix it. mwifiex/sdio.c: In function ‘mwifiex_sdio_resume’: mwifiex/sdio.c:234:16: warning: variable ‘pm_flag’ set but not used [-Wunused-but-set-variable] sdio_get_host_pm_caps() is just an acessor, so the call to it is safe to remove. The unused variable seems to be present since 5e6e3a92 which introduced mwifiex_sdio_resume(). Fixes: 5e6e3a92 ("wireless: mwifiex: initial commit for Marvell mwifiex driver") Cc: Bing Zhao <bzhao@marvell.com> Cc: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by:
-
Kirtika Ruchandani authored
Commit 3935ccc1 introduced mwifiex_tm_cmd() which initializes struct mwifiex_adapter* adapter, but doesn't use it. Compiling with W=1 gives the following warning, fix it. mwifiex/cfg80211.c: In function ‘mwifiex_tm_cmd’: mwifiex/cfg80211.c:3973:26: warning: variable ‘adapter’ set but not used [-Wunused-but-set-variable] Fixes: 3935ccc1 ("mwifiex: add cfg80211 testmode support") Cc: Xinming Hu <huxm@marvell.com> Cc: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by:
-
Kirtika Ruchandani authored
Commit 429d90d2 introduced mwifiex_cmd_tdls_oper() which initializes struct mwifiex_sta_node* sta_ptr, but does not use it. Compiling with W=1 gives the following warning, fix it. mwifiex/sta_cmd.c: In function ‘mwifiex_cmd_tdls_oper’: mwifiex/sta_cmd.c:1732:27: warning: variable ‘sta_ptr’ set but not used [-Wunused-but-set-variable] Fixes: 429d90d2 ("mwifiex: add cfg80211 tdls_oper handler support") Cc: Avinash Patil <patila@marvell.com> Signed-off-by:
-
Kirtika Ruchandani authored
Commit b5413e6b removed all uses of chan_num in mwifiex_config_scan(). Compiling mwifiex with W=1 gives the following warning, fix it. mwifiex/scan.c: In function ‘mwifiex_config_scan’: mwifiex/scan.c:830:6: warning: variable ‘chan_num’ set but not used [-Wunused-but-set-variable] Fixes: b5413e6b ("mwifiex: increase the number of nodes in command pool") Cc: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by:
-
Kirtika Ruchandani authored
Commit bec568ff removed the last remaining usage of struct mwifiex_private* priv in mwifiex_fw_dpc(), by removing the call to mwifiex_del_virtual_intf(). Compiling mwifiex/ with W=1 gives the following warning, fix it. mwifiex/main.c: In function ‘mwifiex_fw_dpc’: mwifiex/main.c:520:26: warning: variable ‘priv’ set but not used [-Wunused-but-set-variable] Fixes: bec568ff ("mwifiex: failure path handling in mwifiex_add_virtual_intf()") Cc: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by:
-
- 28 Nov, 2016 1 commit
-
-
Barry Day authored
Move the dev_info call that attempts to show the rate used before it is set. Signed-off-by:
Barry Day <briselec@gmail.com> Reported-by:
Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by:
-
- 25 Nov, 2016 15 commits
-
-
Tobias Regnery authored
I get the following UBSAN warning during boot on my laptop: ================================================================================ UBSAN: Undefined behaviour in drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_qmath.c:280:21 index 32 is out of range for type 's16 [32]' CPU: 0 PID: 879 Comm: NetworkManager Not tainted 4.9.0-rc4 #28 Hardware name: LENOVO Lenovo IdeaPad N581/INVALID, BIOS 5ECN96WW(V9.01) 03/14/2013 ffff8800b74a6478 ffffffff828e59d2 0000000041b58ab3 ffffffff8398330c ffffffff828e5920 ffff8800b74a64a0 ffff8800b74a6450 0000000000000020 1ffffffff845848c ffffed0016e94bf1 ffffffffc22c2460 000000006b9c0514 Call Trace: [<ffffffff828e59d2>] dump_stack+0xb2/0x110 [<ffffffff828e5920>] ? _atomic_dec_and_lock+0x150/0x150 [<ffffffff82968c9d>] ubsan_epilogue+0xd/0x4e [<ffffffff82969875>] __ubsan_handle_out_of_bounds+0xfa/0x13e [<ffffffff8296977b>] ? __ubsan_handle_shift_out_of_bounds+0x241/0x241 [<ffffffffc0d48379>] ? bcma_host_pci_read16+0x59/0xa0 [bcma] [<ffffffffc0d48388>] ? bcma_host_pci_read16+0x68/0xa0 [bcma] [<ffffffffc212ad78>] ? read_phy_reg+0xe8/0x180 [brcmsmac] [<ffffffffc2184714>] qm_log10+0x2e4/0x350 [brcmsmac] [<ffffffffc2142eb8>] wlc_phy_init_lcnphy+0x538/0x1f20 [brcmsmac] [<ffffffffc2142980>] ? wlc_lcnphy_periodic_cal+0x5c0/0x5c0 [brcmsmac] [<ffffffffc1ba0c93>] ? ieee80211_open+0xb3/0x110 [mac80211] [<ffffffff82f73a02>] ? sk_busy_loop+0x1e2/0x840 [<ffffffff82f7a6ce>] ? __dev_change_flags+0xae/0x220 ... The report is valid: doing the math in this function, with an input value N=63 the variable s16tableIndex gets a value of 31. This value is used as an index in the array log_table with 32 entries. But the next line is: s16errorApproximation = (s16) qm_mulu16(u16offset, (u16) (log_table[s16tableIndex + 1] - log_table[s16tableIndex])); With s16tableIndex + 1 we are trying an out-of-bounds access to the array. The log_table array provides log2 values in q.15 format and the above statement tries an error approximation with the next value. To fix this issue add the next value to the array and update the comment accordingly. Signed-off-by:
Tobias Regnery <tobias.regnery@gmail.com> Signed-off-by:
-
Karthik D A authored
We will read fw_cap_info filled by firmware to check whether to skip ADHOC related commands or not. Also, IBSS_COALESCING_STATUS command has been moved from init path to adhoc network creation path. Signed-off-by:
Karthik D A <karthida@marvell.com> Signed-off-by:
-
Wei Yongjun authored
Fixes the following sparse warning: drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_8192e.c:1559:6: warning: symbol 'rtl8192eu_power_off' was not declared. Should it be static? Signed-off-by:
Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by:
Jes Sorensen <Jes.Sorensen@redhat.com> Signed-off-by:
-
Jes Sorensen authored
In order to obtain retry count for a given rate we need to pass the full struct ieee80211_tx_info to the function setting the rate in he TX descriptor. This uncovered a huge bug where the old code would use struct ieee80211_rate.flags to test for rate parameters, which is always zero, instead of the flags value from struct ieee80211_tx_rate. Time to find a brown paper bag :( Signed-off-by:
-
Jes Sorensen authored
Use the mac80211 provided rate for RTS rather than the hard coded 24Mbps as suggested by the vendor drivers. Reported-by:
Andrea Merello <andrea.merello@gmail.com> Signed-off-by:
-
Jes Sorensen authored
The 8192eu suffered from two issues when reloading the driver. The same problems as with the 8723bu where REG_RX_WAIT_CCA bits 22 and 23 didn't get set in rtl8192e_enable_rf(). In addition it also seems prone to issues when setting REG_RF_CTRL to 0 intead of just disabling the RF_ENABLE bit. Similar to what was causing issues with the 8188eu. With this patch I can successfully reload the driver and reassociate to an APi with an 8192eu dongle. Signed-off-by:
-
Jes Sorensen authored
The generic disable_rf() function clears bits 22 and 23 in REG_RX_WAIT_CCA, however we did not re-enable them again in rtl8723b_enable_rf() This resolves the problem for me with 8723bu devices not working again after reloading the driver. Signed-off-by:
-
Jes Sorensen authored
The full RX descriptor is converted so converting tsfl again would return it to it's original endian value. Signed-off-by:
-
Jes Sorensen authored
A device running without RX package aggregation could return more data in the USB packet than the actual network packet. In this case the could would clone the skb but then determine that that there was no packet to handle and exit without freeing the cloned skb first. This has so far only been observed with 8188eu devices, but could affect others. Signed-off-by:
-
Brian Norris authored
We have a race where the wakeup IRQ might be in flight while we're calling mwifiex_disable_wake() from resume(). This can leave us disabling the IRQ twice. Let's disable the IRQ and enable it in case if we have double-disabled it. Signed-off-by:
-
Brian Norris authored
We don't want to leave the wake IRQ enabled. Signed-off-by:
-
Prameela Rani Garnepudi authored
Transmit power level in a channel is determined based on the dfs region. To support regulatory rules dfs region should be configured to device during set channel request. Also antenna gain values are taken from the mac80211 channel parameters instead of fixed values. Signed-off-by:
Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Signed-off-by:
-
Prameela Rani Garnepudi authored
RSI 9113 device supports single antenna for tx and rx. Support for using external is added. This can be configured from user space using iw. Signed-off-by:
-
Prameela Rani Garnepudi authored
TX power can be configured from iwconfig, iw or from mac80211 when regulatory changes are done. Hence support for configuring tx power to device is added using the RADIO_PARAMS_UPDATE command frame. Signed-off-by:
-
Prameela Rani Garnepudi authored
Filtering rx frames after connection in station mode avoids the overhead of processing un-necessary frames. Hence rx filter frame is added which can be configured to device at suitable times. Signed-off-by:
-
- 23 Nov, 2016 2 commits
-
-
Stanislaw Gruszka authored
Sending frames in CCK rates on HT can cause performance problems. Signed-off-by:
Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by:
-
Stanislaw Gruszka authored
Use RTS/CTS protection for TXOP on all rates modes as default and disable CCK rates (this cause performance problems). Signed-off-by:
-
