This adds nodes for all possible UARTs to sdm845.dtsi. By default
only configure the RX/TX lines with pinctrl. Boards that use UARTs
with flow control can overwrite the configuration in the
<board>.dtsi.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

Add a node for the Camera Subsystem present on the Qualcomm
MSM8996 SoC.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

Add VFE SMMU node.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Reviewed-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

Add pinctrls required for camera sensors:
- power down signal;
- reset signal;
- camera external clock.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

Add pinctrls required for Camera Control Interface.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

Add a node for the Camera Subsystem present on the Qualcomm
MSM8916 SoC.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

Add IOMMU sub-node for VFE secure context bank.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

Each CPU can (and does) participate in cooling down the system but the
DT only captures a handful of them, normally CPU0, in the cooling maps.
Things work by chance currently as under normal circumstances its the
first CPU of each cluster which is used by the operating systems to
probe the cooling devices. But as soon as this CPU ordering changes and
any other CPU is used to bring up the cooling device, we will start
seeing failures.

Also the DT is rather incomplete when we list only one CPU in the
cooling maps, as the hardware doesn't have any such limitations.

Update cooling maps to include all devices affected by individual trip
points.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

The scm binding and driver was updated to rely on the fallback to the
default qcom,scm for any modern SoC and as such both are required. Add
the default compatible to make the scm instance probe.

Fixes: d850156a ("arm64: dts: qcom: msm8998: Add firmware node")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

The SDC2 control pins are typically used to manage sleep.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

The externally accessible SD card slot on the MTP is driven by SDCC2.
Wire it up for use.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

SDCC2 is typically used as the controller for an external SD card slot.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

The root parent clock of most msm8998 clock is the "xo" clock.  The DT node
is incorrectly named "xo_board", which prevents Linux from correctly
parsing the clock tree, resulting in most clocks being unparented and
unable to be manipulated.  The end result is that we can't turn on clocks
for peripherals like SD, so init usually fails.

Fixes: 4807c71c (arm64: dts: Add msm8998 SoC and MTP board support)
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

Qualcomm ARM64 DT Fixes for 4.20-rc1

* Fix reserved gpio ranges for SDM845 and MSM8998

PMS405 also features PON block, so add PON and PWRKEY nodes
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

We can use BAM DAM for serial UART data transfers, so add it
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

Add the BAM DMA instance found in BLSP1 node of the QCS404
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

RNG hardware in QCS404 features (Execution Environment) EE for
HLOS to use, add the node for prng-ee for QCS404.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

Add the TrustZone based remoteproc nodes and their glink edges for
adsp, cdsp and wcss. Enable them for EVB common DTS.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

Add the scm firmware node to QCS404
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

Add the GPIOs present on PMS405 chip.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

RTC is found on PMIC PMS405 and is same as other PMIC used, so add the
rtc node with compatible as qcom,pm8941-rtc
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

PMS405 is used in QCS405-EVB so include that with SPMI nodes
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

Add the pms405 DT file with spmi node.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

Add the sdcc1 node and enable it for the QCS404-EVB.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

Add the QCS404 TLMM pinctrl node with its three tiles.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

Add the smp2p-adsp, smp2p-cdsp and smp2p-wcss nodes found in QCS404.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

Add the RPM regulators found in PMS405 which is used in qcs404-evb
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

Add RPM GLINK node and the RPM message ram, hwspinlock, APCS apps global
and smem nodes it depends on.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

Add the reserved memory regions in QCS404
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

QCS404 has two EVBs, EVB-1000 and EVB-4000. These boards are mostly
similar with few differences in the peripherals used.

So use a common qcs404-evb.dtsi which contains the common parts and use
qcs404-evb-1000.dts and qcs404-evb-4000.dts for diffs
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

Add base dts files for QCS404 chipset along with cpu, timer,
gcc and uart2 nodes.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

RNG hardware in SDM845 features (Execution Environment) EE for
HLOS to use, add the node for prng-ee for sdm845.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

RNG hardware in 8996 features (Execution Environment) EE for
HLOS to use, add the node for prng-ee for msm8996.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

Add a channel node for the die temperature to the ADC.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

The node has a reg property, therefore its name should include a unit
address. Also change the name from 'usb_id_nopull' to 'adc-chan', which
is the preferred name for ADC channel nodes.

Include headers for constants used in the example.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

One thermal zone per cpu is defined
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Acked-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

Initialise the camera thermal zone to export temperature to userspace.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>