Add a fault injector simulating a Kernel panic happening after starting
a transfer. Read the docs for its usage.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Add a fault injector simulating 'arbitration lost' from multi-master
setups. Read the docs for its usage.

A helper function for future fault injectors using SCL interrupts is
created to achieve this.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Multi-master support is defeatured on Tegra210 and Tegra186 due to
known bugs.

This patch removes multi-master support for Tegra210 and Tegra186
I2C HW feature.
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Tegra186 does not have master FIFO  control register and instead
uses FIFO control register like prior Tegra chipset.

This patch fixes this and prevents crashing during boot when
accessing FIFO control registers.
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The phrasing in two dev_err messages is using fallbacking which
os less understandable than "falling back", so fix this up.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Actually, total amount of available minor number for a single major is
MINORMASK + 1. So expand minor range when registering chrdev region.
Signed-off-by: Chengguang Xu <cgxu519@gmx.com>
[wsa: fixed typo in commit message]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

In multi-master environment, this driver's master cannot know
exactly when a peer master sends data to this driver's slave so
cases can be happened that this master tries sending data through
the master_xfer function but slave data from a peer master is still
being processed or slave xfer is started by a peer immediately
after it queues a master command. To support multi-master use cases
properly, this H/W provides arbitration in physical level and it
provides priority based command handling too to avoid conflicts in
multi-master environment, means that if a master and a slave events
happen at the same time, H/W will handle a higher priority event
first and a pending event will be handled when bus comes back to
the idle state.

To support this H/W feature properly, this patch adds the 'pending'
state of master and its handling code so that the pending master
xfer can be continued after slave operation properly.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Merge tag 'at24-5.1-updates-for-wolfram' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into i2c/for-5.1

at24 updates for v5.1

- finally remove legacy platform data as all users have been switched
  to using device properties and nvmem notifier chain
- add support for the 'num-addresses' property

If an smbus transfer fails, there's no guarantee that the output
buffer was written.  So, avoid trying to show the output buffer when
tracing after an error.  This was 'mostly harmless', but would trip
up kasan checking if left-over cruft in byte 0 is a large length,
causing us to read from unwritten memory.
Signed-off-by: John Sperbeck <jsperbeck@google.com>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Add the I2C bus clock speed to the platform data structure.
If not set, default to 100KHz as before.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Some implementations of the OCORES i2c bus master use IO mapped
registers. Add support for getting the IO registers from the platform
data, and register accessor functions.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Miscellaneous style fixes from checkpatch
Signed-off-by: Federico Vaga <federico.vaga@cern.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

It adds the SPDX tag and it removes the old text about the GPLv2.
Signed-off-by: Federico Vaga <federico.vaga@cern.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

This driver assumes that an interrupt line is always available for
the I2C master. This is not always the case and this patch adds support
for a polling version.

Report from Andrew Lunn:

  I did some timing tests for this. On my box, we request a udelay of
  80uS. The kernel actually delays for about 79uS. We then spin in
  ocores_wait() for an additional 10-11uS, which is 3 to 4 iterations.

  There are actually 9 bits on the wire, not 8, since there is an
  ACK/NACK bit after the actual data transfer. So i changed the delay to
  (9 * 1000) / i2c->bus_clock_khz. That resulted in ocores_wait() mostly
  not looping at all. But for reading an 4K AT24 EEPROM, it increased
  the read time by 10ms, from 424ms to 434ms. So we should probably keep
  with 8.
Signed-off-by: Federico Vaga <federico.vaga@cern.ch>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

If the Interrupt Flag (IF) is not set, we should not handle the IRQ:
- the line can be shared with other devices
- it can be a spurious interrupt

To avoid reading twice the status register, the ocores_process() function
expects it to be read by the caller.
Signed-off-by: Federico Vaga <federico.vaga@cern.ch>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Detecting a timeout is ok, but we also need to assert a STOP command on
the bus in order to prevent it from generating interrupts when there are
no on going transfers.

Example: very long transmission.

1. ocores_xfer: START a transfer
2. ocores_isr : handle byte by byte the transfer
3. ocores_xfer: goes in timeout [[bugfix here]]
4. ocores_xfer: return to I2C subsystem and to the I2C driver
5. I2C driver : it may clean up the i2c_msg memory
6. ocores_isr : receives another interrupt (pending bytes to be
                transferred) but the i2c_msg memory is invalid now

So, since the transfer was too long, we have to detect the timeout and
STOP the transfer.

Another point is that we have a critical region here. When handling the
timeout condition we may have a running IRQ handler. For this reason I
introduce a spinlock.

In order to make easier to understan locking I have:
- added a new function to handle timeout
- modified the current ocores_process() function in order to be protected
  by the new spinlock
Like this it is obvious at first sight that this locking serializes
the execution of ocores_process() and ocores_process_timeout()
Signed-off-by: Federico Vaga <federico.vaga@cern.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

This patch adds I2C interface timing registers support for
proper bus rate configuration along with meeting the I2C spec
setup and hold times based on the tuning performed on Tegra210,
Tegra186 and Tegra194 platforms.

I2C_INTERFACE_TIMING_0 register contains TLOW and THIGH field
and Tegra I2C controller design uses them as a part of internal
clock divisor.

I2C_INTERFACE_TIMING_1 register contains the setup and hold times
for start and stop conditions.
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Tegra194 allows max of 64K bytes and Tegra186 and prior allows
max of 4K bytes of transfer per packet.

one sec timeout is not enough for transfers more than 10K bytes
at STD bus rate.

This patch updates I2C transfer timeout based on the transfer size
and I2C bus rate to allow enough time during max transfer size at
lower bus speed.
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

This patch adds DMA support for Tegra I2C.

Tegra I2C TX and RX FIFO depth is 8 words. PIO mode is used for
transfer size of the max FIFO depth and DMA mode is used for
transfer size higher than max FIFO depth to save CPU overhead.

PIO mode needs full intervention of CPU to fill or empty FIFO's
and also need to service multiple data requests interrupt for the
same transaction. This adds delay between data bytes of the same
transfer when CPU is fully loaded and some slave devices has
internal timeout for no bus activity and stops transaction to
avoid bus hang. DMA mode is helpful in such cases.

DMA mode is also helpful for Large transfers during downloading or
uploading FW over I2C to some external devices.

Tegra210 and prior Tegra chips use APBDMA driver which is replaced
with GPCDMA on Tegra186 and Tegra194.
This patch uses has_apb_dma flag in hw_feature to differentiate
DMA driver change between Tegra chipset.

APBDMA driver is registered from module-init level and this patch
also has a change to register I2C driver at module-init level
rather than subsys-init to avoid deferring I2C probe till APBDMA
driver is registered.
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Tegra194 supports maximum 64K bytes per packet including 12 bytes of
packet header irrespective of PIO or DMA mode transfer.

This patch updates Tegra194 max write length to account for packet
header size for transfers.

Cc: stable@vger.kernel.org # 4.20+
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Tegra186 and prior supports maximum 4K bytes per packet transfer
including 12 bytes of packet header.

This patch fixes max write length limit to account packet header
size for transfers.

Cc: stable@vger.kernel.org # 4.4+
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Bus clear feature of Tegra I2C controller helps to recover from
bus hang when I2C master loses the bus arbitration due to the
slave device holding SDA LOW continuously for some unknown reasons.

Per I2C specification, the device that held the bus LOW should
release it within 9 clock pulses.

During bus clear operation, Tegra I2C controller sends 9 clock
pulses and terminates the transaction with STOP condition.
Upon successful bus clear operation, bus goes to idle state and
driver retries the transaction.
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

This patch sorts all the include headers alphabetically for the
I2C Tegra driver.
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

If the device node defines 'num-addresses', let it override the default
behavior.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

Currently the at24 driver only creates additional i2c dummies for
atmel,24c00 and it's hard-coded. Some other chips (like for example
Microchip's 24AA02T) also take more slave addresses despite being
otherwise compatible with already supported variants.

Add a new property to the device tree binding document that defines
the total number of i2c slave addresses taken by the device. The
addresses are counted starting from the one in the reg property.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

There are no more users of at24_platform_data. Remove the relevant
header and modify the driver code to not use it anymore.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

Merge branch 'v5.1/eeprom-for-bartosz' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into at24/for-next

Pull dmaengine fixes from Vinod Koul:
 - Fix in at_xdmac fr wrongful channel state
 - Fix for imx driver for wrong callback invocation
 - Fix to bcm driver for interrupt race & transaction abort.
 - Fix in dmatest to abort in mapping error

* tag 'dmaengine-fix-5.0-rc6' of git://git.infradead.org/users/vkoul/slave-dma:
  dmaengine: dmatest: Abort test in case of mapping error
  dmaengine: bcm2835: Fix abort of transactions
  dmaengine: bcm2835: Fix interrupt race on RT
  dmaengine: imx-dma: fix wrong callback invoke
  dmaengine: at_xdmac: Fix wrongfull report of a channel as in use

Pull x86 fixes from Ingo Molnar:
 "A handful of fixes:

   - Fix an MCE corner case bug/crash found via MCE injection testing

   - Fix 5-level paging boot crash

   - Fix MCE recovery cache invalidation bug

   - Fix regression on Xen guests caused by a recent PMD level mremap
     speedup optimization"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mm: Make set_pmd_at() paravirt aware
  x86/mm/cpa: Fix set_mce_nospec()
  x86/boot/compressed/64: Do not corrupt EDX on EFER.LME=1 setting
  x86/MCE: Initialize mce.bank in the case of a fatal error in mce_no_way_out()

Pull irq fixes from Ingo Molnar:
 "irqchip driver fixes: most of them are race fixes for ARM GIC (General
  Interrupt Controller) variants, but also a fix for the ARM MMP
  (Marvell PXA168 et al) irqchip affecting OLPC keyboards"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/gic-v3-its: Fix ITT_entry_size accessor
  irqchip/mmp: Only touch the PJ4 IRQ & FIQ bits on enable/disable
  irqchip/gic-v3-its: Gracefully fail on LPI exhaustion
  irqchip/gic-v3-its: Plug allocation race for devices sharing a DevID
  irqchip/gic-v4: Fix occasional VLPI drop

Pull perf fixes from Ingo Molnar:
 "A couple of kernel side fixes:

   - Fix the Intel uncore driver on certain hardware configurations

   - Fix a CPU hotplug related memory allocation bug

   - Remove a spurious WARN()

  ... plus also a handful of perf tooling fixes"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf script python: Add Python3 support to tests/attr.py
  perf trace: Support multiple "vfs_getname" probes
  perf symbols: Filter out hidden symbols from labels
  perf symbols: Add fallback definitions for GELF_ST_VISIBILITY()
  tools headers uapi: Sync linux/in.h copy from the kernel sources
  perf clang: Do not use 'return std::move(something)'
  perf mem/c2c: Fix perf_mem_events to support powerpc
  perf tests evsel-tp-sched: Fix bitwise operator
  perf/core: Don't WARN() for impossible ring-buffer sizes
  perf/x86/intel: Delay memory deallocation until x86_pmu_dead_cpu()
  perf/x86/intel/uncore: Add Node ID mask

Pull locking fixes from Ingo Molnar:
 "An rtmutex (PI-futex) deadlock scenario fix, plus a locking
  documentation fix"

* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  futex: Handle early deadlock return correctly
  futex: Fix barrier comment

set_pmd_at() calls native_set_pmd() unconditionally on x86. This was
fine as long as only huge page entries were written via set_pmd_at(),
as Xen pv guests don't support those.

Commit 2c91bd4a ("mm: speed up mremap by 20x on large regions")
introduced a usage of set_pmd_at() possible on pv guests, leading to
failures like:

BUG: unable to handle kernel paging request at ffff888023e26778
#PF error: [PROT] [WRITE]
RIP: e030:move_page_tables+0x7c1/0xae0
move_vma.isra.3+0xd1/0x2d0
__se_sys_mremap+0x3c6/0x5b0
 do_syscall_64+0x49/0x100
entry_SYSCALL_64_after_hwframe+0x44/0xa9

Make set_pmd_at() paravirt aware by just letting it use set_pmd().

Fixes: 2c91bd4a ("mm: speed up mremap by 20x on large regions")
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: xen-devel@lists.xenproject.org
Cc: boris.ostrovsky@oracle.com
Cc: sstabellini@kernel.org
Cc: hpa@zytor.com
Cc: bp@alien8.de
Cc: torvalds@linux-foundation.org
Link: https://lkml.kernel.org/r/20190210074056.11842-1-jgross@suse.com

Pull i2c fixes from Wolfram Sang:
 "One PM related driver bugfix and a MAINTAINERS update"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  MAINTAINERS: Update the ocores i2c bus driver maintainer, etc
  i2c: omap: Use noirq system sleep pm ops to idle device for suspend

Pull MIPS fixes from Paul Burton:
 "A batch of MIPS fixes for 5.0, nothing too scary.

   - A workaround for a Loongson 3 CPU bug is the biggest change, but
     still fairly straightforward. It adds extra memory barriers (sync
     instructions) around atomics to avoid a CPU bug that can break
     atomicity.

   - Loongson64 also sees a fix for powering off some systems which
     would incorrectly reboot rather than waiting for the power down
     sequence to complete.

   - We have DT fixes for the Ingenic JZ4740 SoC & the JZ4780-based Ci20
     board, and a DT warning fix for the Nexsys4/MIPSfpga board.

   - The Cavium Octeon platform sees a further fix to the behaviour of
     the pcie_disable command line argument that was introduced in v3.3.

   - The VDSO, introduced in v4.4, sees build fixes for configurations
     of GCC that were built using the --with-fp-32= flag to specify a
     default 32-bit floating point ABI.

   - get_frame_info() sees a fix for configurations with
     CONFIG_KALLSYMS=n, for which it previously always returned an
     error.

   - If the MIPS Coherence Manager (CM) reports an error then we'll now
     clear that error correctly so that the GCR_ERROR_CAUSE register
     will be updated with information about any future errors"

* tag 'mips_fixes_5.0_3' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
  mips: cm: reprime error cause
  mips: loongson64: remove unreachable(), fix loongson_poweroff().
  MIPS: Remove function size check in get_frame_info()
  MIPS: Use lower case for addresses in nexys4ddr.dts
  MIPS: Loongson: Introduce and use loongson_llsc_mb()
  MIPS: VDSO: Include $(ccflags-vdso) in o32,n32 .lds builds
  MIPS: VDSO: Use same -m%-float cflag as the kernel proper
  MIPS: OCTEON: don't set octeon_dma_bar_type if PCI is disabled
  DTS: CI20: Fix bugs in ci20's device tree.
  MIPS: DTS: jz4740: Correct interrupt number of DMA core

Pull block fixes from Jens Axboe:

 - NVMe pull request from Christoph, fixing namespace locking when
   dealing with the effects log, and a rapid add/remove issue (Keith)

 - blktrace tweak, ensuring requests with -1 sectors are shown (Jan)

 - link power management quirk for a Smasung SSD (Hans)

 - m68k nfblock dynamic major number fix (Chengguang)

 - series fixing blk-iolatency inflight counter issue (Liu)

 - ensure that we clear ->private when setting up the aio kiocb (Mike)

 - __find_get_block_slow() rate limit print (Tetsuo)

* tag 'for-linus-20190209' of git://git.kernel.dk/linux-block:
  blk-mq: remove duplicated definition of blk_mq_freeze_queue
  Blk-iolatency: warn on negative inflight IO counter
  blk-iolatency: fix IO hang due to negative inflight counter
  blktrace: Show requests without sector
  fs: ratelimit __find_get_block_slow() failure message.
  m68k: set proper major_num when specifying module param major_num
  libata: Add NOLPM quirk for SAMSUNG MZ7TE512HMHP-000L1 SSD
  nvme-pci: fix rapid add remove sequence
  nvme: lock NS list changes while handling command effects
  aio: initialize kiocb private in case any filesystems expect it.

Pull mtd fixes from Boris Brezillon:

 - Fix a problem with the imx28 ECC engine

 - Remove a debug trace introduced in 2b6f0090 ("mtd: Check
   add_mtd_device() ret code")

 - Make sure partitions of size 0 can be registered

 - Fix kernel-doc warning in the rawnand core

 - Fix the error path of spinand_init() (missing manufacturer cleanup in
   a few places)

 - Address a problem with the SPI NAND PROGRAM LOAD operation which does
   not work as expected on some parts.

* tag 'mtd/fixes-for-5.0-rc6' of git://git.infradead.org/linux-mtd:
  mtd: rawnand: gpmi: fix MX28 bus master lockup problem
  mtd: Make sure mtd->erasesize is valid even if the partition is of size 0
  mtd: Remove a debug trace in mtdpart.c
  mtd: rawnand: fix kernel-doc warnings
  mtd: spinand: Fix the error/cleanup path in spinand_init()
  mtd: spinand: Handle the case where PROGRAM LOAD does not reset the cache

Pull xen fixes from Juergen Gross:
 "Two very minor fixes: one remove of a #include for an unused header
  and a fix of the xen ML address in MAINTAINERS"

* tag 'for-linus-5.0-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  MAINTAINERS: unify reference to xen-devel list
  arch/arm/xen: Remove duplicate header