- 11 Feb, 2013 3 commits
-
-
Ilan Peer authored
Radar is not required for P2P_DEVICE interfaces. Signed-off-by:
Ilan Peer <ilan.peer@intel.com> Signed-off-by:
Johannes Berg <johannes.berg@intel.com>
-
Larry Finger authored
When a driver requests a specific regulatory domain after cfg80211 already has one, a struct ieee80211_regdomain is leaked. Reported-by:
Larry Finger <Larry.Finger@lwfinger.net> Tested-by:
-
Johannes Berg authored
-
- 08 Feb, 2013 37 commits
-
-
Larry Finger authored
A new model of the RTL8188CUS has appeared. Reported-and-tested-by:
Thomas Rosenkrantz <tom.rosary@googlemail.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Hante Meuleman authored
With this patch off-channel action frames can be transmitted. This is needed for p2p when two devices need to find each other while using different social channels. Reviewed-by:
Arend Van Spriel <arend@broadcom.com> Reviewed-by:
Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by:
Piotr Haber <phaber@broadcom.com> Signed-off-by:
Hante Meuleman <meuleman@broadcom.com> Signed-off-by:
-
Hante Meuleman authored
Currently netdev gets created possibly after returning from add_virtual_intf. This is because add_if is handled asynch. This is wrong and netdev should be up before returning. Reviewed-by:
-
Hante Meuleman authored
Remove some unused defines and comments. Also use same define for IE length. Reviewed-by:
-
Hante Meuleman authored
When adding a virtual interface cfg80211 already has taken the rtnl_lock. So when the netdevice is being registered the register_netdevice should be used instead of register_netdev. Reviewed-by:
-
Hante Meuleman authored
Currently there is a sleep after disconnect on del_station. This timeout is not needed (anymore) and is causing problems with p2p setup, because remote side disconnects then supplicant will do del_station and while it waits the 400ms remote side will already reconnect and that is something supplicant cant handle. Reviewed-by:
-
Hante Meuleman authored
Wiphy object holds information about possible netdev combinations which can be supported. This needs updating for p2p device. Also p2p device netdev has wrong 80211 iftype. Limit the change interface support to match the netdev configuration/combination possibilities. Reviewed-by:
-
Hante Meuleman authored
Reviewed-by:
-
Hante Meuleman authored
All interfaces for ifidx is 0 are created ahead and therefor double registrations for not only bssidx 0, but ifidx 0 should be ignored in brcfm_add_if. Reviewed-by:
-
Hante Meuleman authored
Reviewed-by:
-
Hante Meuleman authored
Use the stored role in wdev struct to determine AP/GO role. This simplifies code. Fix stop_ap for GO role. Reviewed-by:
-
Hante Meuleman authored
Add module variable with which a p2p0 netdev can be created. This netdev can be used by wpa-supplicant to configure and set up the p2p client/GO. Reviewed-by:
-
Arend van Spriel authored
cfg80211 api change needs to be applied. this change will be squashed with introducing commit: commit 68751daec95b07a74b18aa22b2f9c196991dbe81 Author: Hante Meuleman <meuleman@broadcom.com> Date: Mon Nov 26 12:21:27 2012 +0100 brcmfmac: add support for P2P listen mode. Signed-off-by: -
Hante Meuleman authored
In some rare situations the wpa_supplicant can lock up on a remain on channel command. Use actual cookies for the remain on channel related commands and allow for additional remain on channel while still having one set. Reviewed-by:
-
Hante Meuleman authored
With this patch it is possible to send action frames. Reviewed-by:
-
Hante Meuleman authored
Once wpa_supplicant has registered for P2P action frames all received action frames for the device are passed up to cfg80211. Reviewed-by:
-
Hante Meuleman authored
With this update it is possible to create an P2P go. Handle the p2p go role in creation and the update beacon from cfg80211. Also store primary bss in global struct. Needed to map cfg device back to primary device. Reviewed-by:
-
Hante Meuleman authored
In preparation of p2p connections update the sta connect setup and handling routines. Use join iovar and bsscfg commands where applicable. Handle assoc ind per bsscfg (vif) and generalize vndr ie setup to support assoc IEs and support all setup types, e.g. sta, ap and p2p. Reviewed-by:
-
Hante Meuleman authored
Mask is OR-ed with value in case of deregister. Should be AND-ed. Reviewed-by:
-
Hante Meuleman authored
Add support for changing existing interface into p2p go interface. Reviewed-by:
-
Hante Meuleman authored
Improve exception handling. Store and removed created vif in cfg.p2p.bss array. Fix big endian bug. Fix msec jiffies bug. Reviewed-by:
-
Hante Meuleman authored
Add support for scanning on non primary netdev (p2p) and simplify the p2p scanning preparation. Reviewed-by:
-
Arend van Spriel authored
Deletion of the virtual interface was not fully supported so adding it now. Tested using p2p_connect command in wpa_supplicant. Reviewed-by:
-
Arend van Spriel authored
The driver determines the P2P interface address and device address from the primary mac address. However, the function used an invalid input. This caused a mac address mismatch between firmware and driver. This was hidden because the brcmf_if_add() function corrected the error upon receiving the IF_ADD event from firmware. Reviewed-by:
-
Arend van Spriel authored
On 64-bit target a warning was given when using %d to print sizeof() value: CC [M] drivers/net/wireless/brcm80211/brcmfmac/wl_cfg80211.o brcm80211/brcmfmac/wl_cfg80211.c: In function 'brcmf_alloc_vif': brcm80211/brcmfmac/wl_cfg80211.c:3884:2: error: format '%d' expects argument of type 'int', but argument 3 has type 'long unsigned int' [-Werror=format] Fixed using %zu instead. Reviewed-by:
-
Hante Meuleman authored
With this patch a device can be put in p2p listen mode and becomes visible for other p2p devices (via p2p_find). Reviewed-by:
-
Arend van Spriel authored
This patch allow the creation of P2P client and group owner virtual interfaces in the driver. Reviewed-by:
Franky (Zhenhui) Lin <frankyl@broadcom.com> Signed-off-by:
-
Arend van Spriel authored
First part for P2P support. It is a variation on the existing scanning functionality and is used to discover peer-to-peer group owners and/or peer-to-peer devices in listen state. Tested with wpa_cli/wpa_supplicant v2.0-devel. Reviewed-by:
-
Piotr Haber authored
Locking host access in trap info processing is not needed as bus access functions do it on their own. Reviewed-by:
-
Piotr Haber authored
Make sure backplane clocks are on while reading crash data. Reviewed-by:
-
Piotr Haber authored
fix wrong locking in crash info processing Reviewed-by:
-
Hante Meuleman authored
When unloading it is possible that drvr is not null, but iflist[0] is. So check iflist[0] pointer before using it. Reviewed-by:
-
Hante Meuleman authored
Upon receiving an IF event from the firmware the interface was created and stored on a list using the interface index. With upcoming P2P feature the firmware will send a IF event in which two interfaces have the same interface index. To uniquely locate them on the list the bss index is now used. Reviewed-by:
-
Joe Perches authored
alloc failures already get standardized OOM messages and a dump_stack. Signed-off-by:
Joe Perches <joe@perches.com> Signed-off-by:
-
Tim Gardner authored
Dynamically allocate the probe response template which avoids potential stack corruption. Observed with smatch: drivers/net/wireless/brcm80211/brcmsmac/main.c:7412 brcms_c_bss_update_probe_resp() warn: 'prb_resp' puts 512 bytes on stack Cc: Brett Rudley <brudley@broadcom.com> Cc: Arend van Spriel <arend@broadcom.com> Cc: "Franky (Zhenhui) Lin" <frankyl@broadcom.com> Cc: Hante Meuleman <meuleman@broadcom.com> Cc: "John W. Linville" <linville@tuxdriver.com> Cc: Seth Forshee <seth.forshee@canonical.com> Cc: Pieter-Paul Giesberts <pieterpg@broadcom.com> Cc: Hauke Mehrtens <hauke@hauke-m.de> Cc: linux-wireless@vger.kernel.org Cc: brcm80211-dev-list@broadcom.com Cc: netdev@vger.kernel.org Signed-off-by:
Tim Gardner <tim.gardner@canonical.com> Acked-by:
-
Tim Gardner authored
DOT11_MIN_BEACON_PERIOD and DOT11_MAX_BEACON_PERIOD are superfluous. The only invalid beacon period is 0. Comparing a 16 bit quantity to 0xffff also causes a compile warning: drivers/net/wireless/brcm80211/brcmsmac/main.c:5560 brcms_c_set_beacon_period() warn: impossible condition '(period > 65535) => (0-65535 > 65535)' Observed from smatch analysis. Cc: Brett Rudley <brudley@broadcom.com> Cc: Arend van Spriel <arend@broadcom.com> Cc: "Franky (Zhenhui) Lin" <frankyl@broadcom.com> Cc: Hante Meuleman <meuleman@broadcom.com> Cc: "John W. Linville" <linville@tuxdriver.com> Cc: Pieter-Paul Giesberts <pieterpg@broadcom.com> Cc: Seth Forshee <seth.forshee@canonical.com> Cc: Hauke Mehrtens <hauke@hauke-m.de> Cc: linux-wireless@vger.kernel.org Cc: brcm80211-dev-list@broadcom.com Cc: netdev@vger.kernel.org Signed-off-by:
-
Jiri Slaby authored
It can, if invalid argument given, return a negative value. In that case we would access arrays out-of-bounds and such. Check the value and yell loudly if that happened as it would be a bug in the implementation. (Instead of silently corrupting memory.) Signed-off-by:
Jiri Slaby <jslaby@suse.cz> Cc: Nick Kossifidis <mickflemm@gmail.com> Cc: "Luis R. Rodriguez" <mcgrof@qca.qualcomm.com> Signed-off-by:
-
