The LEN2006 Synaptics touchpad (as found in Thinkpad E540) returns wrong
min max values.

touchpad-edge-detector output:
>  Touchpad SynPS/2 Synaptics TouchPad on /dev/input/event6
>  Move one finger around the touchpad to detect the actual edges
>  Kernel says:    x [1472..5674], y [1408..4684]
>  Touchpad sends: x [1264..5675], y [1171..4688]

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=88211
Cc: stable@vger.kernel.org
Signed-off-by: Binyamin Sagal <bensagal@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

A chapter is added to describe the trackpoint packets.

A section is added to describe the behaviour of the knob crc_enabled in
sysfs.

The introduction of the documentation only mentioned v1/v2, but in the
last part it already contains explanation of v3 and v4. The introduction
is updated.
Signed-off-by: Ulrik De Bie <ulrik.debie-os@e2big.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The detection of crc_enabled is known to fail for Fujitsu H730. A DMI
blacklist is added for that, but it can be expected that other laptops will
pop up with this.

Here a sysfs knob is provided to alter the behaviour of crc_enabled.
Writing 0 or 1 to it sets the variable to 0 or 1. Reading it will show the
crc_enabled variable (0 or 1).
Reported-by: Stefan Valouch <stefan@valouch.com>
Signed-off-by: Ulrik De Bie <ulrik.debie-os@e2big.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

In the past, no elantech was known with 3 touchpad mouse buttons.
Fujitsu H730 is the first known elantech with a middle button. This commit
enables this middle button. For backwards compatibility, the Fujitsu is
detected via DMI, and only for this one 3 buttons will be announced.
Reported-by: Stefan Valouch <stefan@valouch.com>
Signed-off-by: Ulrik De Bie <ulrik.debie-os@e2big.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Sometimes on Dell Latitude laptops psmouse/alps driver receive invalid ALPS
protocol V3 packets with bit7 set in last byte. More often it can be
reproduced on Dell Latitude E6440 or E7440 with closed lid and pushing
cover above touchpad.

If bit7 in last packet byte is set then it is not valid ALPS packet. I was
told that ALPS devices never send these packets. It is not know yet who
send those packets, it could be Dell EC, bug in BIOS and also bug in
touchpad firmware...

With this patch alps driver does not process those invalid packets, but
instead of reporting PSMOUSE_BAD_DATA, getting into out of sync state,
getting back in sync with the next byte and spam dmesg we return
PSMOUSE_FULL_PACKET. If driver is truly out of sync we'll fail the checks
on the next byte and report PSMOUSE_BAD_DATA then.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Pali Rohár <pali.rohar@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

On some Dell Latitude laptops ALPS device or Dell EC send one invalid byte
in 6 bytes ALPS packet. In this case psmouse driver enter out of sync
state. It looks like that all other bytes in packets are valid and also
device working properly. So there is no need to do full device reset, just
need to wait for byte which match condition for first byte (start of
packet). Because ALPS packets are bigger (6 or 8 bytes) default limit is
small.

This patch increase number of invalid bytes to size of 2 ALPS packets which
psmouse driver can drop before do full reset.

Resetting ALPS devices take some time and when doing reset on some Dell
laptops touchpad, trackstick and also keyboard do not respond. So it is
better to do it only if really necessary.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

5th and 6th byte of ALPS trackstick V3 protocol match condition for first
byte of PS/2 3 bytes packet. When driver enters out of sync state and ALPS
trackstick is sending data then driver match 5th, 6th and next 1st bytes as
PS/2.

It basically means if user is using trackstick when driver is in out of
sync state driver will never resync. Processing these bytes as 3 bytes PS/2
data cause total mess (random cursor movements, random clicks) and make
trackstick unusable until psmouse driver decide to do full device reset.

Lot of users reported problems with ALPS devices on Dell Latitude E6440,
E6540 and E7440 laptops. ALPS device or Dell EC for unknown reason send
some invalid ALPS PS/2 bytes which cause driver out of sync. It looks like
that i8042 and psmouse/alps driver always receive group of 6 bytes packets
so there are no missing bytes and no bytes were inserted between valid
ones.

This patch does not fix root of problem with ALPS devices found in Dell
Latitude laptops but it does not allow to process some (invalid)
subsequence of 6 bytes ALPS packets as 3 bytes PS/2 when driver is out of
sync.

So with this patch trackstick input device does not report bogus data when
also driver is out of sync, so trackstick should be usable on those
machines.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Pali Rohár <pali.rohar@gmail.com>
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The Fujitsu H730 does not work with crc_enabled = 0, even though the
crc_enabled bit in the firmware version indicated it would. When switching
this value to crc_enabled to 1, the touchpad works. This patch uses DMI to
detect H730.
Reported-by: Stefan Valouch <stefan@valouch.com>
Tested-by: Stefan Valouch <stefan@valouch.com>
Tested-by: Alfredo Gemma <alfredo.gemma@gmail.com>
Signed-off-by: Ulrik De Bie <ulrik.debie-os@e2big.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The Fujitsu H730 has hardware v4 with a trackpoint. This enables the
elantech_report_trackpoint for v4.
Reported-by: Stefan Valouch <stefan@valouch.com>
Tested-by: Stefan Valouch <stefan@valouch.com>
Tested-by: Alfredo Gemma <alfredo.gemma@gmail.com>
Signed-off-by: Ulrik De Bie <ulrik.debie-os@e2big.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This button is treated as a wakeup source, so we need to initialise it
correctly.

Without the device_init_wakeup() call, dev->power.wakeup will
be NULL, and pm_wakeup_event() will do nothing.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The new Lenovo T440s laptop has a different PnP ID "LEN0039", and it
needs the similar min/max quirk to make its clickpad working.

BugLink: https://bugzilla.opensuse.org/show_bug.cgi?id=903748Reported-and-tested-by: Joschi Brauchle <joschibrauchle@gmx.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This reverts commit 68da1664.

It turns out that the assertion about scope of regressions due to
always keeping keyboard controller in legacy mode was proven wrong.
There are laptops, such as Clevo W650SH, that only have internal
touchpad (no external PS/2 ports), that require active multiplexing
mode to switch the touchpad (Elantech) into native mode instead of
basic PS/2 emulation.
Reported-by: Roel Aaij <roel.aaij@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The irq function altera_ps2_rxint returns an irqreturn_t, so use the
same type for variable storing the return value.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

In altera_ps2_close, the data register (offset 0) is written instead of
the control register (offset 4), leading to the RX interrupt not being
disabled. Fix this by calling writel() with the offset for the proper
register.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Expression haptic->pwm_dev->period * haptic->magnitude is of type
'unsigned int' and may overflow. We need to convert one of the operands
to u64 before multiplying, instead of casting result (potentially
overflown) to u64.

Reported by Coverity: CID 1248753

Acked-by : Jaewon Kim <jaewon02.kim@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

psmouse_reconnect() will not be called if psmouse driver is not bound to
the serio port, so there is no point in checking that.  Also, as coded, it
introduces potential NULL dereference in psmouse_dbg() in case psmouse is
indeed NULL. Let's just remove it.

Detected by Coverity: CID 146528
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

I believe the intent of the code was to drop oldest bytes from the queue,
not the latest if we drop one byte and both latest and some oldest of we
are dropping more than one.
Acked-by: Jan-Benedict Glaw <jbglaw@lug-owl.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Coverity pointed out that at return point error is always 0 so the
conditional is not needed.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

When I was adjusting patch in 848d4793 to
use devm_ioremap_resource() I messed it up.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Sharp SL-6000 (tosa) touchscreen needs wider limits to properly map all
points on the screen. Expand ranges in abs_x and abs_y arrays according
to the touchscreen area.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

These models need i8042.notimeout, otherwise the touchpad will not work.

BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=69731
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1111138
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The bitmask comment says it will enable GPIO 8-14 and 16-20 for keypad use,
but it actually enables GPIO 8-11 and 13-20 due to a bit error.

Instead of masking of the "hole" at GPIO 12 (which is used for keypad
output 4) mask of the proper "hole" at GPIO 15.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Add the new flags argument to calls of (devm_)gpiod_get*().

Currently both forms (with or without the flags argument) are valid thanks
to transitional macros in <linux/gpio/consumer.h>. These macros will be
removed once all consumers are updated and the flags argument will become
compulsory.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Add Thrustmaster as Xbox 360 controller vendor. This is required for
example to make the GP XID (044f:b326) gamepad work.
Signed-off-by: Tommi Rantala <tt.rantala@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Add the USB ID for the Xbox 360 Thrustmaster Ferrari 458 Racing Wheel.
Signed-off-by: Tommi Rantala <tt.rantala@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The check to see whether the device is already disabled in
max77693_haptic_disable() was inversed, this change corrects it.
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

xenkbd_disconnect_backend doesn't free grant table entry.  This bug affects
live migration.

xenkbd_disconnect_backend uses gnttab_end_foreign_access_ref to handle
grant table entry which doesn't really free an entry.

Thus every time we do xenkbd_resume, grant table entry increses by one. As
an grant table entry occupies 8 bytes, an grant table page has at most 512
entries. Every 512 times we do xenkdb_resume, grant table pages increses by
one.

After around 3500 times of live migration, grant table pages will increase
by 7, causing too many pages to populate and hitting max_pages limit when
assigning pages.Thus assign_pages will fail, so will live migration.
Signed-off-by: Chang Huaixin <huaixin.chx@alibaba-inc.com>
Acked-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Since the change to struct input_mt_pos some variables are now bitfields
instead of integers. Automatic conversion from integer to bitfield entry
destroys information, therefore enforce boolean interpretation instead.

Link: https://bugzilla.redhat.com/show_bug.cgi?id=1114768
Fixes: 02d04254 ("Input: alps - use struct input_mt_pos to track coordinates")
Signed-off-by: Andreas Bosch <linux@progandy.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Prepare second round of input updates for 3.18.

Active multiplexing is a nice feature as it allows several pointing devices
(such as touchpad and external mouse) use their native protocols at the
same time. Unfortunately many manufacturers do not implement the feature
properly even though they advertise it. The problematic implementations are
never fixed, since Windows by default does not use this mode, and move from
one BIOS/model of laptop to another. When active multiplexing is broken
turning it on usually results in touchpad, keyboard, or both unresponsive.

With PS/2 usage on decline (most of PS/2 devices in use nowadays are
internal laptop touchpads), I expect number of users who have laptops with
working MUX implementation, docking stations with external PS/2 ports, and
who are still using external PS/2 mice, to be rather small. Let's flip the
default to be OFF and allow activating it through i8042.nomux=0 kernel
option.  We'll also keep DMI table where we can record known good models.
Acked-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Without this the aux port does not get detected, and consequently the
touchpad will not work.

https://bugzilla.redhat.com/show_bug.cgi?id=1110011

Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Unfortunately, ForcePad capability is not actually exported over PS/2, so
we have to resort to DMI checks.

Cc: stable@vger.kernel.org
Reported-by: Nicole Faerber <nicole.faerber@kernelconcepts.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Synchronize with mainline to bring in changes to Synaptics and i8042
drivers.

This patch adds support for the ar1021 i2c based touchscreen.
The driver is quite simple and only supports the Touch
Reporting Protocol.

This is the final version for an RFC patch send a while ago.
http://www.spinics.net/lists/linux-input/msg29419.htmlSigned-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

To enable the cros_ec_keyb driver to be auto-loaded when build as
module add an of match table (and export it) to match the modalias
information passed on to userspace as the Cros EC MFD driver registers
the MFD subdevices with an of_compatibility string.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Fix the format string for serio device name generation to avoid negative
device numbers when the id exceeds the maximum signed integer value.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Fix the format string for input device name generation to avoid negative
device numbers when the id exceeds the maximum signed integer value.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Let's automatically set EV_ABS bit in device's event type list when calling
input_set_abs_params() so that drivers do not have to do it explicitly.

These calls are never in a hot paths so we won't lose much time by setting
the same bit several times.
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

In case we start with the device not fully quiesced we should make sure we
cancel the workqueue after freeing interrupt.
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This change switch to managed resources to simplifies error handling
and module unloading and does away with platform_driver remove function.
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>