On egress side, xfrm lookup is called from __gre6_xmit() with the
fl6_gre_key field not initialized leading to policies selectors check
failure. Consequently, gre packets are sent without encryption.

On ingress side, INET6_PROTO_NOPOLICY was set, thus packets were not
checked against xfrm policies. Like for egress side, fl6_gre_key should be
correctly set, this is now done in decode_session6().

Fixes: c12b395a ("gre: Support GRE over IPv6")
Cc: stable@vger.kernel.org
Signed-off-by: Ghalem Boudour <ghalem.boudour@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>

Nikolay Aleksandrov says:

====================
net: nexthop: fix refcount issues when replacing groups

This set fixes a refcount bug when replacing nexthop groups and
modifying routes. It is complex because the objects look valid when
debugging memory dumps, but we end up having refcount dependency between
unlinked objects which can never be released, so in turn they cannot
free their resources and refcounts. The problem happens because we can
have stale IPv6 per-cpu dsts in nexthops which were removed from a
group. Even though the IPv6 gen is bumped, the dsts won't be released
until traffic passes through them or the nexthop is freed, that can take
arbitrarily long time, and even worse we can create a scenario[1] where it
can never be released. The fix is to release the IPv6 per-cpu dsts of
replaced nexthops after an RCU grace period so no new ones can be
created. To do that we add a new IPv6 stub - fib6_nh_release_dsts, which
is used by the nexthop code only when necessary. We can further optimize
group replacement, but that is more suited for net-next as these patches
would have to be backported to stable releases.

v2: patch 02: update commit msg
    patch 03: check for mausezahn before testing and make a few comments
              more verbose

[1]
This info is also present in patch 02's commit message.
Initial state:
 $ ip nexthop list
  id 200 via 2002:db8::2 dev bridge.10 scope link onlink
  id 201 via 2002:db8::3 dev bridge scope link onlink
  id 203 group 201/200
 $ ip -6 route
  2001:db8::10 nhid 203 metric 1024 pref medium
     nexthop via 2002:db8::3 dev bridge weight 1 onlink
     nexthop via 2002:db8::2 dev bridge.10 weight 1 onlink

Create rt6_info through one of the multipath legs, e.g.:
 $ taskset -a -c 1  ./pkt_inj 24 bridge.10 2001:db8::10
 (pkt_inj is just a custom packet generator, nothing special)

Then remove that leg from the group by replace (let's assume it is id
200 in this case):
 $ ip nexthop replace id 203 group 201

Now remove the IPv6 route:
 $ ip -6 route del 2001:db8::10/128

The route won't be really deleted due to the stale rt6_info holding 1
refcnt in nexthop id 200.
At this point we have the following reference count dependency:
 (deleted) IPv6 route holds 1 reference over nhid 203
 nh 203 holds 1 ref over id 201
 nh 200 holds 1 ref over the net device and the route due to the stale
 rt6_info

Now to create circular dependency between nh 200 and the IPv6 route, and
also to get a reference over nh 200, restore nhid 200 in the group:
 $ ip nexthop replace id 203 group 201/200

And now we have a permanent circular dependncy because nhid 203 holds a
reference over nh 200 and 201, but the route holds a ref over nh 203 and
is deleted.

To trigger the bug just delete the group (nhid 203):
 $ ip nexthop del id 203

It won't really be deleted due to the IPv6 route dependency, and now we
have 2 unlinked and deleted objects that reference each other: the group
and the IPv6 route. Since the group drops the reference it holds over its
entries at free time (i.e. its own refcount needs to drop to 0) that will
never happen and we get a permanent ref on them, since one of the entries
holds a reference over the IPv6 route it will also never be released.

At this point the dependencies are:
 (deleted, only unlinked) IPv6 route holds reference over group nh 203
 (deleted, only unlinked) group nh 203 holds reference over nh 201 and 200
 nh 200 holds 1 ref over the net device and the route due to the stale
 rt6_info

This is the last point where it can be fixed by running traffic through
nh 200, and specifically through the same CPU so the rt6_info (dst) will
get released due to the IPv6 genid, that in turn will free the IPv6
route, which in turn will free the ref count over the group nh 203.

If nh 200 is deleted at this point, it will never be released due to the
ref from the unlinked group 203, it will only be unlinked:
 $ ip nexthop del id 200
 $ ip nexthop
 $

Now we can never release that stale rt6_info, we have IPv6 route with ref
over group nh 203, group nh 203 with ref over nh 200 and 201, nh 200 with
rt6_info (dst) with ref over the net device and the IPv6 route. All of
these objects are only unlinked, and cannot be released, thus they can't
release their ref counts.

 Message from syslogd@dev at Nov 19 14:04:10 ...
  kernel:[73501.828730] unregister_netdevice: waiting for bridge.10 to become free. Usage count = 3
 Message from syslogd@dev at Nov 19 14:04:20 ...
  kernel:[73512.068811] unregister_netdevice: waiting for bridge.10 to become free. Usage count = 3

====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The new selftest runs a sequence which causes circular refcount
dependency between deleted objects which cannot be released and results
in a netdevice refcount imbalance.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When replacing a nexthop group, we must release the IPv6 per-cpu dsts of
the removed nexthop entries after an RCU grace period because they
contain references to the nexthop's net device and to the fib6 info.
With specific series of events[1] we can reach net device refcount
imbalance which is unrecoverable. IPv4 is not affected because dsts
don't take a refcount on the route.

[1]
 $ ip nexthop list
  id 200 via 2002:db8::2 dev bridge.10 scope link onlink
  id 201 via 2002:db8::3 dev bridge scope link onlink
  id 203 group 201/200
 $ ip -6 route
  2001:db8::10 nhid 203 metric 1024 pref medium
     nexthop via 2002:db8::3 dev bridge weight 1 onlink
     nexthop via 2002:db8::2 dev bridge.10 weight 1 onlink

Create rt6_info through one of the multipath legs, e.g.:
 $ taskset -a -c 1  ./pkt_inj 24 bridge.10 2001:db8::10
 (pkt_inj is just a custom packet generator, nothing special)

Then remove that leg from the group by replace (let's assume it is id
200 in this case):
 $ ip nexthop replace id 203 group 201

Now remove the IPv6 route:
 $ ip -6 route del 2001:db8::10/128

The route won't be really deleted due to the stale rt6_info holding 1
refcnt in nexthop id 200.
At this point we have the following reference count dependency:
 (deleted) IPv6 route holds 1 reference over nhid 203
 nh 203 holds 1 ref over id 201
 nh 200 holds 1 ref over the net device and the route due to the stale
 rt6_info

Now to create circular dependency between nh 200 and the IPv6 route, and
also to get a reference over nh 200, restore nhid 200 in the group:
 $ ip nexthop replace id 203 group 201/200

And now we have a permanent circular dependncy because nhid 203 holds a
reference over nh 200 and 201, but the route holds a ref over nh 203 and
is deleted.

To trigger the bug just delete the group (nhid 203):
 $ ip nexthop del id 203

It won't really be deleted due to the IPv6 route dependency, and now we
have 2 unlinked and deleted objects that reference each other: the group
and the IPv6 route. Since the group drops the reference it holds over its
entries at free time (i.e. its own refcount needs to drop to 0) that will
never happen and we get a permanent ref on them, since one of the entries
holds a reference over the IPv6 route it will also never be released.

At this point the dependencies are:
 (deleted, only unlinked) IPv6 route holds reference over group nh 203
 (deleted, only unlinked) group nh 203 holds reference over nh 201 and 200
 nh 200 holds 1 ref over the net device and the route due to the stale
 rt6_info

This is the last point where it can be fixed by running traffic through
nh 200, and specifically through the same CPU so the rt6_info (dst) will
get released due to the IPv6 genid, that in turn will free the IPv6
route, which in turn will free the ref count over the group nh 203.

If nh 200 is deleted at this point, it will never be released due to the
ref from the unlinked group 203, it will only be unlinked:
 $ ip nexthop del id 200
 $ ip nexthop
 $

Now we can never release that stale rt6_info, we have IPv6 route with ref
over group nh 203, group nh 203 with ref over nh 200 and 201, nh 200 with
rt6_info (dst) with ref over the net device and the IPv6 route. All of
these objects are only unlinked, and cannot be released, thus they can't
release their ref counts.

 Message from syslogd@dev at Nov 19 14:04:10 ...
  kernel:[73501.828730] unregister_netdevice: waiting for bridge.10 to become free. Usage count = 3
 Message from syslogd@dev at Nov 19 14:04:20 ...
  kernel:[73512.068811] unregister_netdevice: waiting for bridge.10 to become free. Usage count = 3

Fixes: 7bf4796d ("nexthops: add support for replace")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We need a way to release a fib6_nh's per-cpu dsts when replacing
nexthops otherwise we can end up with stale per-cpu dsts which hold net
device references, so add a new IPv6 stub called fib6_nh_release_dsts.
It must be used after an RCU grace period, so no new dsts can be created
through a group's nexthop entry.
Similar to fib6_nh_release it shouldn't be used if fib6_nh_init has failed
so it doesn't need a dummy stub when IPv6 is not enabled.

Fixes: 7bf4796d ("nexthops: add support for replace")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When IPv6 module gets initialized, but it's hitting an error in inet6_init()
where it then needs to undo all the prior initialization work, it also might
do a call to ndisc_cleanup() which then calls neigh_table_clear(). In there
is a missing timer cancellation of the table's managed_work item.

The kernel test robot explicitly triggered this error path and caused a UAF
crash similar to the below:

  [...]
  [   28.833183][    C0] BUG: unable to handle page fault for address: f7a43288
  [   28.833973][    C0] #PF: supervisor write access in kernel mode
  [   28.834660][    C0] #PF: error_code(0x0002) - not-present page
  [   28.835319][    C0] *pde = 06b2c067 *pte = 00000000
  [   28.835853][    C0] Oops: 0002 [#1] PREEMPT
  [   28.836367][    C0] CPU: 0 PID: 303 Comm: sed Not tainted 5.16.0-rc1-00233-g83ff5faa0d3b #7
  [   28.837293][    C0] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-1 04/01/2014
  [   28.838338][    C0] EIP: __run_timers.constprop.0+0x82/0x440
  [...]
  [   28.845607][    C0] Call Trace:
  [   28.845942][    C0]  <SOFTIRQ>
  [   28.846333][    C0]  ? check_preemption_disabled.isra.0+0x2a/0x80
  [   28.846975][    C0]  ? __this_cpu_preempt_check+0x8/0xa
  [   28.847570][    C0]  run_timer_softirq+0xd/0x40
  [   28.848050][    C0]  __do_softirq+0xf5/0x576
  [   28.848547][    C0]  ? __softirqentry_text_start+0x10/0x10
  [   28.849127][    C0]  do_softirq_own_stack+0x2b/0x40
  [   28.849749][    C0]  </SOFTIRQ>
  [   28.850087][    C0]  irq_exit_rcu+0x7d/0xc0
  [   28.850587][    C0]  common_interrupt+0x2a/0x40
  [   28.851068][    C0]  asm_common_interrupt+0x119/0x120
  [...]

Note that IPv6 module cannot be unloaded as per 8ce44061 ("ipv6: do not
allow ipv6 module to be removed") hence this can only be seen during module
initialization error. Tested with kernel test robot's reproducer.

Fixes: 7482e384 ("net, neigh: Add NTF_MANAGED flag for managed neighbor entries")
Reported-by: kernel test robot <oliver.sang@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Li Zhijian <zhijianx.li@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The change to eth_hw_addr_set() caused gcc to correctly spot a
bug that was introduced in an earlier incorrect fix:

In file included from include/linux/etherdevice.h:21,
                 from drivers/net/ethernet/ni/nixge.c:7:
In function '__dev_addr_set',
    inlined from 'eth_hw_addr_set' at include/linux/etherdevice.h:319:2,
    inlined from 'nixge_probe' at drivers/net/ethernet/ni/nixge.c:1286:3:
include/linux/netdevice.h:4648:9: error: 'memcpy' reading 6 bytes from a region of size 0 [-Werror=stringop-overread]
 4648 |         memcpy(dev->dev_addr, addr, len);
      |         ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

As nixge_get_nvmem_address() can return either NULL or an error
pointer, the NULL check is wrong, and we can end up reading from
ERR_PTR(-EOPNOTSUPP), which gcc knows to contain zero readable
bytes.

Make the function always return an error pointer again but fix
the check to match that.

Fixes: f3956ebb ("ethernet: use eth_hw_addr_set() instead of ether_addr_copy()")
Fixes: abcd3d6f ("net: nixge: Fix error path for obtaining mac address")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Possible recursive locking is detected by lockdep when SMC
falls back to TCP. The corresponding warnings are as follows:

 ============================================
 WARNING: possible recursive locking detected
 5.16.0-rc1+ #18 Tainted: G            E
 --------------------------------------------
 wrk/1391 is trying to acquire lock:
 ffff975246c8e7d8 (&ei->socket.wq.wait){..-.}-{3:3}, at: smc_switch_to_fallback+0x109/0x250 [smc]

 but task is already holding lock:
 ffff975246c8f918 (&ei->socket.wq.wait){..-.}-{3:3}, at: smc_switch_to_fallback+0xfe/0x250 [smc]

 other info that might help us debug this:
  Possible unsafe locking scenario:

        CPU0
        ----
   lock(&ei->socket.wq.wait);
   lock(&ei->socket.wq.wait);

  *** DEADLOCK ***

  May be due to missing lock nesting notation

 2 locks held by wrk/1391:
  #0: ffff975246040130 (sk_lock-AF_SMC){+.+.}-{0:0}, at: smc_connect+0x43/0x150 [smc]
  #1: ffff975246c8f918 (&ei->socket.wq.wait){..-.}-{3:3}, at: smc_switch_to_fallback+0xfe/0x250 [smc]

 stack backtrace:
 Call Trace:
  <TASK>
  dump_stack_lvl+0x56/0x7b
  __lock_acquire+0x951/0x11f0
  lock_acquire+0x27a/0x320
  ? smc_switch_to_fallback+0x109/0x250 [smc]
  ? smc_switch_to_fallback+0xfe/0x250 [smc]
  _raw_spin_lock_irq+0x3b/0x80
  ? smc_switch_to_fallback+0x109/0x250 [smc]
  smc_switch_to_fallback+0x109/0x250 [smc]
  smc_connect_fallback+0xe/0x30 [smc]
  __smc_connect+0xcf/0x1090 [smc]
  ? mark_held_locks+0x61/0x80
  ? __local_bh_enable_ip+0x77/0xe0
  ? lockdep_hardirqs_on+0xbf/0x130
  ? smc_connect+0x12a/0x150 [smc]
  smc_connect+0x12a/0x150 [smc]
  __sys_connect+0x8a/0xc0
  ? syscall_enter_from_user_mode+0x20/0x70
  __x64_sys_connect+0x16/0x20
  do_syscall_64+0x34/0x90
  entry_SYSCALL_64_after_hwframe+0x44/0xae

The nested locking in smc_switch_to_fallback() is considered to
possibly cause a deadlock because smc_wait->lock and clc_wait->lock
are the same type of lock. But actually it is safe so far since
there is no other place trying to obtain smc_wait->lock when
clc_wait->lock is held. So the patch replaces spin_lock() with
spin_lock_nested() to avoid false report by lockdep.

Link: https://lkml.org/lkml/2021/11/19/962
Fixes: 2153bd1e ("Transfer remaining wait queue entries during fallback")
Reported-by: syzbot+e979d3597f48262cb4ee@syzkaller.appspotmail.com
Signed-off-by: Wen Gu <guwen@linux.alibaba.com>
Acked-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It turns out that vhost vsock violates the virtio spec
by supplying the out buffer length in the used length
(should just be the in length).
As a result, attempts to validate the used length fail with:
vmw_vsock_virtio_transport virtio1: tx: used len 44 is larger than in buflen 0

Since vsock driver does not use the length fox tx and
validates the length before use for rx, it is safe to
suppress the validation in virtio core for this driver.
Reported-by: Halil Pasic <pasic@linux.ibm.com>
Fixes: 939779f5 ("virtio_ring: validate used buffer length")
Cc: "Jason Wang" <jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Function axspi_read_status calls:

    ret = spi_write_then_read(ax_spi->spi, ax_spi->cmd_buf, 1,
                              (u8 *)&status, 3);

status is a pointer to a struct spi_status, which is 3-byte wide:

    struct spi_status {
        u16 isr;
        u8 status;
    };

But &status is the pointer to this pointer, and spi_write_then_read does
not dereference this parameter:

    int spi_write_then_read(struct spi_device *spi,
                            const void *txbuf, unsigned n_tx,
                            void *rxbuf, unsigned n_rx)

Therefore axspi_read_status currently receive a SPI response in the
pointer status, which overwrites 24 bits of the pointer.

Thankfully, on Little-Endian systems, the pointer is only used in

    le16_to_cpus(&status->isr);

... which is a no-operation. So there, the overwritten pointer is not
dereferenced. Nevertheless on Big-Endian systems, this can lead to
dereferencing pointers after their 24 most significant bits were
overwritten. And in all systems this leads to possible use of
uninitialized value in functions calling spi_write_then_read which
expect status to be initialized when the function returns.

Moreover function axspi_read_status (and macro AX_READ_STATUS) do not
seem to be used anywhere. So currently this seems to be dead code. Fix
the issue anyway so that future code works properly when using function
axspi_read_status.

Fixes: a97c69ba ("net: ax88796c: ASIX AX88796C SPI Ethernet Adapter Driver")
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Acked-by: Łukasz Stelmach <l.stelmach@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, when user space emits SIOCSHWTSTAMP ioctl calls such as
enabling/disabling timestamping or changing filter settings, the driver
reads the current CLOCK_REALTIME value and programming this into the
NIC's hardware clock. This might be necessary during system
initialization, but at runtime, when the PTP clock has already been
synchronized to a grandmaster, a reset of the timestamp settings might
result in a clock jump. Furthermore, if the clock is also controlled by
phc2sys in automatic mode (where the UTC offset is queried from ptp4l),
that UTC-to-TAI offset (currently 37 seconds in 2021) would be
temporarily reset to 0, and it would take a long time for phc2sys to
readjust so that CLOCK_REALTIME and the PHC are apart by 37 seconds
again.

To address the issue, we introduce a new function called
stmmac_init_tstamp_counter(), which gets called during ndo_open().
It contains the code snippet moved from stmmac_hwtstamp_set() that
manages the time synchronization. Besides, the sub second increment
configuration is also moved here since the related values are hardware
dependent and runtime invariant.

Furthermore, the hardware clock must be kept running even when no time
stamping mode is selected in order to retain the synchronized time base.
That way, timestamping can be enabled again at any time only with the
need to compensate the clock's natural drifting.

As a side effect, this patch fixes the issue that ptp_clock_info::enable
can be called before SIOCSHWTSTAMP and the driver (which looks at
priv->systime_flags) was not prepared to handle that ordering.

Fixes: 92ba6888 ("stmmac: add the support for PTP hw clock driver")
Reported-by: Michael Olbrich <m.olbrich@pengutronix.de>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Holger Assmann <h.assmann@pengutronix.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use nn->tlv_caps.me_freq_mhz instead of nn->me_freq_mhz to check whether
rx-usecs/tx-usecs is valid.

This is because nn->tlv_caps.me_freq_mhz represents the clock_freq (MHz) of
the flow processing cores (FPC) on the NIC. While nn->me_freq_mhz is not
be set.

Fixes: ce991ab6 ("nfp: read ME frequency from vNIC ctrl memory")
Signed-off-by: Diana Wang <na.wang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

We deal with IPv6 packets, so we need to use IP6CB(skb)->flags and
IP6SKB_REROUTED, instead of IPCB(skb)->flags and IPSKB_REROUTED

Found by code inspection, please double check that fixing this bug
does not surface other bugs.

Fixes: 09ee9dba ("ipv6: Reinject IPv6 packets if IPsec policy matches after SNAT")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tobias Brunner <tobias@strongswan.org>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: David Ahern <dsahern@kernel.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Tested-by: Tobias Brunner <tobias@strongswan.org>
Acked-by: Tobias Brunner <tobias@strongswan.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

old tc(iproute2-5.9.0) output:
 action order 1: bpf action.o:[action-ok] id 60 tag bcf7977d3b93787c jited default-action pipe
newer tc(iproute2-5.14.0) output:
 action order 1: bpf action.o:[action-ok] id 64 name tag bcf7977d3b93787c jited default-action pipe

It can fix below errors:
 # ok 260 f84a - Add cBPF action with invalid bytecode
 # not ok 261 e939 - Add eBPF action with valid object-file
 #       Could not match regex pattern. Verify command output:
 # total acts 0
 #
 #       action order 1: bpf action.o:[action-ok] id 42 name  tag bcf7977d3b93787c jited default-action pipe
 #        index 667 ref 1 bind 0
Signed-off-by: Li Zhijian <zhijianx.li@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We should not always presume all kernels use pfifo_fast as the default qdisc.

For example, a fq_codel qdisk could have below output:
qdisc fq_codel 0: parent 1:4 limit 10240p flows 1024 quantum 1514 target 5ms interval 100ms memory_limit 32Mb ecn drop_batch 64
Reported-by: kernel test robot <lkp@intel.com>
Suggested-by: Peilin Ye <peilin.ye@bytedance.com>
Signed-off-by: Li Zhijian <zhijianx.li@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qca8k has a global MTU, so its tracking the MTU per port to make sure
that the largest MTU gets applied.
Since it uses the frame size instead of MTU the driver MTU change function
will then add the size of Ethernet header and checksum on top of MTU.

The driver currently populates the per port MTU size as Ethernet frame
length + checksum which equals 1518.

The issue is that then MTU change function will go through all of the
ports, find the largest MTU and apply the Ethernet header + checksum on
top of it again, so for a desired MTU of 1500 you will end up with 1536.

This is obviously incorrect, so to correct it populate the per port struct
MTU with just the MTU and not include the Ethernet header + checksum size
as those will be added by the MTU change function.

Fixes: f58d2598 ("net: dsa: qca8k: implement the port MTU callbacks")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With SGMII phy the internal delay is always applied to the PAD0 config.
This is caused by the falling edge configuration that hardcode the reg
to PAD0 (as the falling edge bits are present only in PAD0 reg)
Move the delay configuration before the reg overwrite to correctly apply
the delay.

Fixes: cef08115 ("net: dsa: qca8k: set internal delay also for sgmii")
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On kernels before v5.15, calling read() on a unix socket after
shutdown(SHUT_RD) or shutdown(SHUT_RDWR) would return the data
previously written or EOF.  But now, while read() after
shutdown(SHUT_RD) still behaves the same way, read() after
shutdown(SHUT_RDWR) always fails with -EINVAL.

This behaviour change was apparently inadvertently introduced as part of
a bug fix for a different regression caused by the commit adding sockmap
support to af_unix, commit 94531cfc ("af_unix: Add
unix_stream_proto for sockmap").  Those commits, for unclear reasons,
started setting the socket state to TCP_CLOSE on shutdown(SHUT_RDWR),
while this state change had previously only been done in
unix_release_sock().

Restore the original behaviour.  The sockmap tests in
tests/selftests/bpf continue to pass after this patch.

Fixes: d0c6416b ("unix: Fix an issue in unix_shutdown causing the other end read/write failures")
Link: https://lore.kernel.org/lkml/20211111140000.GA10779@axis.com/Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Tested-by: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Paolo Abeni says:

====================
mptcp: fix 3rd ack rtx timer

Eric noted that the MPTCP code do the wrong thing to schedule
the MPJ 3rd ack timer. He also provided a patch to address the
issues (patch 1/2).

To fix for good the MPJ 3rd ack retransmission timer, we additionally
need to set it after the current ack is transmitted (patch 2/2)

Note that the bug went unnotice so far because all the related
tests required some running data transfer, and that causes
MPTCP-level ack even on the opening MPJ subflow. We now have
explicit packet drill coverage for this code path.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Scheduling a delack in mptcp_established_options_mp() is
not a good idea: such function is called by tcp_send_ack() and
the pending delayed ack will be cleared shortly after by the
tcp_event_ack_sent() call in __tcp_transmit_skb().

Instead use the mptcp delegated action infrastructure to
schedule the delayed ack after the current bh processing completes.

Additionally moves the schedule_3rdack_retransmission() helper
into protocol.c to avoid making it visible in a different compilation
unit.

Fixes: ec3edaa7 ("mptcp: Add handling of outgoing MP_JOIN requests")
Reviewed-by: Mat Martineau <mathew.j.martineau&gt;@linux.intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To compute the rtx timeout schedule_3rdack_retransmission() does multiple
things in the wrong way: srtt_us is measured in usec/8 and the timeout
itself is an absolute value.

Fixes: ec3edaa7 ("mptcp: Add handling of outgoing MP_JOIN requests")
Acked-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <mathew.j.martineau&gt;@linux.intel.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

queue

Tony Nguyen says:

====================
Intel Wired LAN Driver Updates 2021-11-19

This series contains updates to iavf driver only.

Nitesh prevents user from changing interrupt settings when adaptive
interrupt moderation is on.

Jedrzej resolves a hang that occurred when interface was closed while a
reset was occurring and fixes statistics to be updated when requested to
prevent stale values.

Brett adjusts driver to accommodate changes in supported VLAN features
that could occur during reset and cause various errors to be reported.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When a VF goes through a reset, it's possible for the VF's feature set
to change. For example it may lose the VIRTCHNL_VF_OFFLOAD_VLAN
capability after VF reset. Unfortunately, the driver doesn't correctly
deal with this situation and errors are seen from downing/upping the
interface and/or moving the interface in/out of a network namespace.

When setting the interface down/up we see the following errors after the
VIRTCHNL_VF_OFFLOAD_VLAN capability was taken away from the VF:

ice 0000:51:00.1: VF 1 failed opcode 12, retval: -64 iavf 0000:51:09.1:
Failed to add VLAN filter, error IAVF_NOT_SUPPORTED ice 0000:51:00.1: VF
1 failed opcode 13, retval: -64 iavf 0000:51:09.1: Failed to delete VLAN
filter, error IAVF_NOT_SUPPORTED

These add/delete errors are happening because the VLAN filters are
tracked internally to the driver and regardless of the VLAN_ALLOWED()
setting the driver tries to delete/re-add them over virtchnl.

Fix the delete failure by making sure to delete any VLAN filter tracking
in the driver when a removal request is made, while preventing the
virtchnl request.  This makes it so the driver's VLAN list is up to date
and the errors are

Fix the add failure by making sure the check for VLAN_ALLOWED() during
reset is done after the VF receives its capability list from the PF via
VIRTCHNL_OP_GET_VF_RESOURCES. If VLAN functionality is not allowed, then
prevent requesting re-adding the filters over virtchnl.

When moving the interface into a network namespace we see the following
errors after the VIRTCHNL_VF_OFFLOAD_VLAN capability was taken away from
the VF:

iavf 0000:51:09.1 enp81s0f1v1: NIC Link is Up Speed is 25 Gbps Full Duplex
iavf 0000:51:09.1 temp_27: renamed from enp81s0f1v1
iavf 0000:51:09.1 mgmt: renamed from temp_27
iavf 0000:51:09.1 dev27: set_features() failed (-22); wanted 0x020190001fd54833, left 0x020190001fd54bb3

These errors are happening because we aren't correctly updating the
netdev capabilities and dealing with ndo_fix_features() and
ndo_set_features() correctly.

Fix this by only reporting errors in the driver's ndo_set_features()
callback when VIRTCHNL_VF_OFFLOAD_VLAN is not allowed and any attempt to
enable the VLAN features is made. Also, make sure to disable VLAN
insertion, filtering, and stripping since the VIRTCHNL_VF_OFFLOAD_VLAN
flag applies to all of them and not just VLAN stripping.

Also, after we process the capabilities in the VF reset path, make sure
to call netdev_update_features() in case the capabilities have changed
in order to update the netdev's feature set to match the VF's actual
capabilities.

Lastly, make sure to always report success on VLAN filter delete when
VIRTCHNL_VF_OFFLOAD_VLAN is not supported. The changed flow in
iavf_del_vlans() allows the stack to delete previosly existing VLAN
filters even if VLAN filtering is not allowed. This makes it so the VLAN
filter list is up to date.

Fixes: 8774370d ("i40e/i40evf: support for VF VLAN tag stripping control")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Currently iavf adapter statistics are refreshed only in a
watchdog task, triggered approximately every two seconds,
which causes some ethtool requests to return outdated values.

Add explicit statistics refresh when requested by ethtool -S.

Fixes: b476b003 ("iavf: Move commands processing to the separate function")
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

System hangs if close the interface is called from the kernel during
the interface is in resetting state.
During resetting operation the link is closing but kernel didn't
know it and it tried to close this interface again what sometimes
led to deadlock.
Inform kernel about current state of interface
and turn off the flag IFF_UP when interface is closing until reset
is finished.
Previously it was most likely to hang the system when kernel
(network manager) tried to close the interface in the same time
when interface was in resetting state because of deadlock.

Fixes: 3c8e0b98 ("i40vf: don't stop me now")
Signed-off-by: Jaroslaw Gawin <jaroslawx.gawin@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Resolve being able to change static values on VF when adaptive interrupt
moderation is enabled.

This problem is fixed by checking the interrupt settings is not
a combination of change of static value while adaptive interrupt
moderation is turned on.

Without this fix, the user would be able to change static values
on VF with adaptive moderation enabled.

Fixes: 65e87c03 ("i40evf: support queue-specific settings for interrupt moderation")
Signed-off-by: Nitesh B Venkatesh <nitesh.b.venkatesh@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

This bug report came up when we were testing the device driver
by fuzzing. It shows that buf1_len can get underflowed and be
0xfffffffc (4294967292).

This bug is triggerable with a compromised/malfunctioning device.
We found the bug through QEMU emulation tested the patch with
emulation. We did NOT test it on real hardware.

Attached is the bug report by fuzzing.

BUG: KASAN: use-after-free in stmmac_napi_poll_rx+0x1c08/0x36e0 [stmmac]
Read of size 4294967292 at addr ffff888016358000 by task ksoftirqd/0/9

CPU: 0 PID: 9 Comm: ksoftirqd/0 Tainted: G        W         5.6.0 #1
Call Trace:
 dump_stack+0x76/0xa0
 print_address_description.constprop.0+0x16/0x200
 ? stmmac_napi_poll_rx+0x1c08/0x36e0 [stmmac]
 ? stmmac_napi_poll_rx+0x1c08/0x36e0 [stmmac]
 __kasan_report.cold+0x37/0x7c
 ? stmmac_napi_poll_rx+0x1c08/0x36e0 [stmmac]
 kasan_report+0xe/0x20
 check_memory_region+0x15a/0x1d0
 memcpy+0x20/0x50
 stmmac_napi_poll_rx+0x1c08/0x36e0 [stmmac]
 ? stmmac_suspend+0x850/0x850 [stmmac]
 ? __next_timer_interrupt+0xba/0xf0
 net_rx_action+0x363/0xbd0
 ? call_timer_fn+0x240/0x240
 ? __switch_to_asm+0x40/0x70
 ? napi_busy_loop+0x520/0x520
 ? __schedule+0x839/0x15a0
 __do_softirq+0x18c/0x634
 ? takeover_tasklets+0x5f0/0x5f0
 run_ksoftirqd+0x15/0x20
 smpboot_thread_fn+0x2f1/0x6b0
 ? smpboot_unregister_percpu_thread+0x160/0x160
 ? __kthread_parkme+0x80/0x100
 ? smpboot_unregister_percpu_thread+0x160/0x160
 kthread+0x2b5/0x3b0
 ? kthread_create_on_node+0xd0/0xd0
 ret_from_fork+0x22/0x40
Reported-by: Brendan Dolan-Gavitt <brendandg@nyu.edu>
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We found this bug while fuzzing the device driver. Using and freeing
the dangling pointer buff->skb would cause use-after-free and
double-free.

This bug is triggerable with compromised/malfunctioning devices. We
found the bug with QEMU emulation and tested the patch by emulation.
We did NOT test on a real device.

Attached is the bug report.

BUG: KASAN: double-free or invalid-free in consume_skb+0x6c/0x1c0

Call Trace:
 dump_stack+0x76/0xa0
 print_address_description.constprop.0+0x16/0x200
 ? consume_skb+0x6c/0x1c0
 kasan_report_invalid_free+0x61/0xa0
 ? consume_skb+0x6c/0x1c0
 __kasan_slab_free+0x15e/0x170
 ? consume_skb+0x6c/0x1c0
 kfree+0x8c/0x230
 consume_skb+0x6c/0x1c0
 aq_ring_tx_clean+0x5c2/0xa80 [atlantic]
 aq_vec_poll+0x309/0x5d0 [atlantic]
 ? _sub_I_65535_1+0x20/0x20 [atlantic]
 ? __next_timer_interrupt+0xba/0xf0
 net_rx_action+0x363/0xbd0
 ? call_timer_fn+0x240/0x240
 ? __switch_to_asm+0x34/0x70
 ? napi_busy_loop+0x520/0x520
 ? net_tx_action+0x379/0x720
 __do_softirq+0x18c/0x634
 ? takeover_tasklets+0x5f0/0x5f0
 run_ksoftirqd+0x15/0x20
 smpboot_thread_fn+0x2f1/0x6b0
 ? smpboot_unregister_percpu_thread+0x160/0x160
 ? __kthread_parkme+0x80/0x100
 ? smpboot_unregister_percpu_thread+0x160/0x160
 kthread+0x2b5/0x3b0
 ? kthread_create_on_node+0xd0/0xd0
 ret_from_fork+0x22/0x40
Reported-by: Brendan Dolan-Gavitt <brendandg@nyu.edu>
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Reviewed-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

fix error path handling in prestera_bridge_port_join() that
cases prestera driver to crash (see below).

 Trace:
   Internal error: Oops: 96000044 [#1] SMP
   Modules linked in: prestera_pci prestera uio_pdrv_genirq
   CPU: 1 PID: 881 Comm: ip Not tainted 5.15.0 #1
   pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
   pc : prestera_bridge_destroy+0x2c/0xb0 [prestera]
   lr : prestera_bridge_port_join+0x2cc/0x350 [prestera]
   sp : ffff800011a1b0f0
   ...
   x2 : ffff000109ca6c80 x1 : dead000000000100 x0 : dead000000000122
    Call trace:
   prestera_bridge_destroy+0x2c/0xb0 [prestera]
   prestera_bridge_port_join+0x2cc/0x350 [prestera]
   prestera_netdev_port_event.constprop.0+0x3c4/0x450 [prestera]
   prestera_netdev_event_handler+0xf4/0x110 [prestera]
   raw_notifier_call_chain+0x54/0x80
   call_netdevice_notifiers_info+0x54/0xa0
   __netdev_upper_dev_link+0x19c/0x380

Fixes: e1189d9a ("net: marvell: prestera: Add Switchdev driver implementation")
Signed-off-by: Volodymyr Mytnyk <vmytnyk@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Return NOTIFY_DONE (dont't care) for switchdev notifications
that prestera driver don't know how to handle them.

With introduction of SWITCHDEV_BRPORT_[UN]OFFLOADED switchdev
events, the driver rejects adding swport to bridge operation
which is handled by prestera_bridge_port_join() func. The root
cause of this is that prestera driver returns error (EOPNOTSUPP)
in prestera_switchdev_blk_event() handler for unknown swdev
events. This causes switchdev_bridge_port_offload() to fail
when adding port to bridge in prestera_bridge_port_join().

Fixes: 957e2235 ("net: make switchdev_bridge_port_{,unoffload} loosely coupled with the bridge")
Signed-off-by: Volodymyr Mytnyk <vmytnyk@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

The following patchset contains Netfilter/IPVS fixes for net:

1) Add selftest for vrf+conntrack, from Florian Westphal.

2) Extend nfqueue selftest to cover nfqueue, also from Florian.

3) Remove duplicated include in nft_payload, from Wan Jiabing.

4) Several improvements to the nat port shadowing selftest,
   from Phil Sutter.

5) Fix filtering of reply tuple in ctnetlink, from Florent Fourcot.

6) Do not override error with -EINVAL in filter setup path, also
   from Florent.

7) Honor sysctl_expire_nodest_conn regardless conn_reuse_mode for
   reused connections, from yangxingwu.

8) Replace snprintf() by sysfs_emit() in xt_IDLETIMER as reported
   by Coccinelle, from Jing Yao.

9) Incorrect IPv6 tunnel match in flowtable offload, from Will
   Mortensen.

10) Switch port shadow selftest to use socat, from Florian Westphal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from Jakub Kicinski:
 "Including fixes from bpf, mac80211.

  Current release - regressions:

   - devlink: don't throw an error if flash notification sent before
     devlink visible

   - page_pool: Revert "page_pool: disable dma mapping support...",
     turns out there are active arches who need it

  Current release - new code bugs:

   - amt: cancel delayed_work synchronously in amt_fini()

  Previous releases - regressions:

   - xsk: fix crash on double free in buffer pool

   - bpf: fix inner map state pruning regression causing program
     rejections

   - mac80211: drop check for DONT_REORDER in __ieee80211_select_queue,
     preventing mis-selecting the best effort queue

   - mac80211: do not access the IV when it was stripped

   - mac80211: fix radiotap header generation, off-by-one

   - nl80211: fix getting radio statistics in survey dump

   - e100: fix device suspend/resume

  Previous releases - always broken:

   - tcp: fix uninitialized access in skb frags array for Rx 0cp

   - bpf: fix toctou on read-only map's constant scalar tracking

   - bpf: forbid bpf_ktime_get_coarse_ns and bpf_timer_* in tracing
     progs

   - tipc: only accept encrypted MSG_CRYPTO msgs

   - smc: transfer remaining wait queue entries during fallback, fix
     missing wake ups

   - udp: validate checksum in udp_read_sock() (when sockmap is used)

   - sched: act_mirred: drop dst for the direction from egress to
     ingress

   - virtio_net_hdr_to_skb: count transport header in UFO, prevent
     allowing bad skbs into the stack

   - nfc: reorder the logic in nfc_{un,}register_device, fix unregister

   - ipsec: check return value of ipv6_skip_exthdr

   - usb: r8152: add MAC passthrough support for more Lenovo Docks"

* tag 'net-5.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (96 commits)
  ptp: ocp: Fix a couple NULL vs IS_ERR() checks
  net: ethernet: dec: tulip: de4x5: fix possible array overflows in type3_infoblock()
  net: tulip: de4x5: fix the problem that the array 'lp->phy[8]' may be out of bound
  ipv6: check return value of ipv6_skip_exthdr
  e100: fix device suspend/resume
  devlink: Don't throw an error if flash notification sent before devlink visible
  page_pool: Revert "page_pool: disable dma mapping support..."
  ethernet: hisilicon: hns: hns_dsaf_misc: fix a possible array overflow in hns_dsaf_ge_srst_by_port()
  octeontx2-af: debugfs: don't corrupt user memory
  NFC: add NCI_UNREG flag to eliminate the race
  NFC: reorder the logic in nfc_{un,}register_device
  NFC: reorganize the functions in nci_request
  tipc: check for null after calling kmemdup
  i40e: Fix display error code in dmesg
  i40e: Fix creation of first queue by omitting it if is not power of two
  i40e: Fix warning message and call stack during rmmod i40e driver
  i40e: Fix ping is lost after configuring ADq on VF
  i40e: Fix changing previously set num_queue_pairs for PFs
  i40e: Fix NULL ptr dereference on VSI filter sync
  i40e: Fix correct max_pkt_size on VF RX queue
  ...

Pull btrfs fixes from David Sterba:
 "Several xes and one old ioctl deprecation. Namely there's fix for
  crashes/warnings with lzo compression that was suspected to be caused
  by first pull merge resolution, but it was a different bug.

  Summary:

   - regression fix for a crash in lzo due to missing boundary checks of
     the page array

   - fix crashes on ARM64 due to missing barriers when synchronizing
     status bits between work queues

   - silence lockdep when reading chunk tree during mount

   - fix false positive warning in integrity checker on devices with
     disabled write caching

   - fix signedness of bitfields in scrub

   - start deprecation of balance v1 ioctl"

* tag 'for-5.16-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  btrfs: deprecate BTRFS_IOC_BALANCE ioctl
  btrfs: make 1-bit bit-fields of scrub_page unsigned int
  btrfs: check-integrity: fix a warning on write caching disabled disk
  btrfs: silence lockdep when reading chunk tree during mount
  btrfs: fix memory ordering between normal and ordered work functions
  btrfs: fix a out-of-bound access in copy_compressed_data_to_page()

Pull UDF fix from Jan Kara:
 "A fix for a long-standing UDF bug where we were not properly
  validating directory position inside readdir"

* tag 'fs_for_v5.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
  udf: Fix crash after seekdir

Pull setattr idmapping fix from Christian Brauner:
 "This contains a simple fix for setattr. When determining the validity
  of the attributes the ia_{g,u}id fields contain the value that will be
  written to inode->i_{g,u}id. When the {g,u}id attribute of the file
  isn't altered and the caller's fs{g,u}id matches the current {g,u}id
  attribute the attribute change is allowed.

  The value in ia_{g,u}id does already account for idmapped mounts and
  will have taken the relevant idmapping into account. So in order to
  verify that the {g,u}id attribute isn't changed we simple need to
  compare the ia_{g,u}id value against the inode's i_{g,u}id value.

  This only has any meaning for idmapped mounts as idmapping helpers are
  idempotent without them. And for idmapped mounts this really only has
  a meaning when circular idmappings are used, i.e. mappings where e.g.
  id 1000 is mapped to id 1001 and id 1001 is mapped to id 1000. Such
  ciruclar mappings can e.g. be useful when sharing the same home
  directory between multiple users at the same time.

  Before this patch we could end up denying legitimate attribute changes
  and allowing invalid attribute changes when circular mappings are
  used. To even get into this situation the caller must've been
  privileged both to create that mapping and to create that idmapped
  mount.

  This hasn't been seen in the wild anywhere but came up when expanding
  the fstest suite during work on a series of hardening patches. All
  idmapped fstests pass without any regressions and we're adding new
  tests to verify the behavior of circular mappings.

  The new tests can be found at [1]"

Link: https://lore.kernel.org/linux-fsdevel/20211109145713.1868404-2-brauner@kernel.org [1]

* tag 'fs.idmapped.v5.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
  fs: handle circular mappings correctly

Pull parisc fixes from Helge Deller:
 "parisc bug and warning fixes and wire up futex_waitv.

  Fix some warnings which showed up with allmodconfig builds, a revert
  of a change to the sigreturn trampoline which broke signal handling,
  wire up futex_waitv and add CONFIG_PRINTK_TIME=y to 32bit defconfig"

* tag 'for-5.16/parisc-4' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: Enable CONFIG_PRINTK_TIME=y in 32bit defconfig
  Revert "parisc: Reduce sigreturn trampoline to 3 instructions"
  parisc: Wrap assembler related defines inside __ASSEMBLY__
  parisc: Wire up futex_waitv
  parisc: Include stringify.h to avoid build error in crypto/api.c
  parisc/sticon: fix reverse colors

Pull KVM fixes from Paolo Bonzini:
 "Selftest changes:

   - Cleanups for the perf test infrastructure and mapping hugepages

   - Avoid contention on mmap_sem when the guests start to run

   - Add event channel upcall support to xen_shinfo_test

  x86 changes:

   - Fixes for Xen emulation

   - Kill kvm_map_gfn() / kvm_unmap_gfn() and broken gfn_to_pfn_cache

   - Fixes for migration of 32-bit nested guests on 64-bit hypervisor

   - Compilation fixes

   - More SEV cleanups

  Generic:

   - Cap the return value of KVM_CAP_NR_VCPUS to both KVM_CAP_MAX_VCPUS
     and num_online_cpus(). Most architectures were only using one of
     the two"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (42 commits)
  KVM: x86: Cap KVM_CAP_NR_VCPUS by KVM_CAP_MAX_VCPUS
  KVM: s390: Cap KVM_CAP_NR_VCPUS by num_online_cpus()
  KVM: RISC-V: Cap KVM_CAP_NR_VCPUS by KVM_CAP_MAX_VCPUS
  KVM: PPC: Cap KVM_CAP_NR_VCPUS by KVM_CAP_MAX_VCPUS
  KVM: MIPS: Cap KVM_CAP_NR_VCPUS by KVM_CAP_MAX_VCPUS
  KVM: arm64: Cap KVM_CAP_NR_VCPUS by kvm_arm_default_max_vcpus()
  KVM: x86: Assume a 64-bit hypercall for guests with protected state
  selftests: KVM: Add /x86_64/sev_migrate_tests to .gitignore
  riscv: kvm: fix non-kernel-doc comment block
  KVM: SEV: Fix typo in and tweak name of cmd_allowed_from_miror()
  KVM: SEV: Drop a redundant setting of sev->asid during initialization
  KVM: SEV: WARN if SEV-ES is marked active but SEV is not
  KVM: SEV: Set sev_info.active after initial checks in sev_guest_init()
  KVM: SEV: Disallow COPY_ENC_CONTEXT_FROM if target has created vCPUs
  KVM: Kill kvm_map_gfn() / kvm_unmap_gfn() and gfn_to_pfn_cache
  KVM: nVMX: Use a gfn_to_hva_cache for vmptrld
  KVM: nVMX: Use kvm_read_guest_offset_cached() for nested VMCS check
  KVM: x86/xen: Use sizeof_field() instead of open-coding it
  KVM: nVMX: Use kvm_{read,write}_guest_cached() for shadow_vmcs12
  KVM: x86/xen: Fix get_attr of KVM_XEN_ATTR_TYPE_SHARED_INFO
  ...

Pull documentation fixes from Jonathan Corbet:
 "A handful of documentation fixes for 5.16"

* tag 'docs-5.16-2' of git://git.lwn.net/linux:
  Documentation/process: fix a cross reference
  Documentation: update vcpu-requests.rst reference
  docs: accounting: update delay-accounting.rst reference
  libbpf: update index.rst reference
  docs: filesystems: Fix grammatical error "with" to "which"
  doc/zh_CN: fix a translation error in management-style
  docs: ftrace: fix the wrong path of tracefs
  Documentation: arm: marvell: Fix link to armada_1000_pb.pdf document
  Documentation: arm: marvell: Put Armada XP section between Armada 370 and 375
  Documentation: arm: marvell: Add some links to homepage / product infos
  docs: Update Sphinx requirements

Pull printk fixes from Petr Mladek:

 - Try to flush backtraces from other CPUs also on the local one. This
   was a regression caused by printk_safe buffers removal.

 - Remove header dependency warning.

* tag 'printk-for-5.16-fixup' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux:
  printk: Remove printk.h inclusion in percpu.h
  printk: restore flushing of NMI buffers on remote CPUs after NMI backtraces

The ptp_ocp_get_mem() function does not return NULL, it returns error
pointers.

Fixes: 773bda96 ("ptp: ocp: Expose various resources on the timecard.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>