The MBIM specification allows a MBIM device to disguise
itself as NCM for backwards compatibility, using additional
altsettings with different subclass (control) or protocol
(data):

C:* #Ifs= 2 Cfg#= 1 Atr=80 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0d Prot=00 Driver=cdc_mbim
E:  Ad=81(I) Atr=03(Int.) MxPS=  64 Ivl=7ms
I:* If#= 0 Alt= 1 #EPs= 1 Cls=02(comm.) Sub=0e Prot=00 Driver=cdc_mbim
E:  Ad=81(I) Atr=03(Int.) MxPS=  64 Ivl=7ms
I:  If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=01 Driver=cdc_mbim
I:  If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=01 Driver=cdc_mbim
E:  Ad=81(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 2 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E:  Ad=81(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms

If the MBIM driver is enabled then that should have priority
for devices providing such a NCM 1.0 backward compatibility
mode.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Suarez <gsuarez@smithmicro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

The CDC Mobile Broadband Interface Model (MBIM) specification
extends CDC NCM by
 - removing the redundant ethernet header from the point-to-point
   USB channel
 - adding support for multiple IP (v4 and/or v6) sessions multiplexed
   on the same USB channel
 - adding a MBIM control channel encapsulated in CDC
 - adding Device Service Streams (DSS), which are non IP generic data
   streams multiplexed on the same USB channel as the IP sessions

MBIM devices are managed using the dedicated control channel, and no
data will flow on the data channel until a control session has been
established.  This driver has no knowledge of MBIM control messages.
It just exports the control channel to a /dev/cdc-wdmX character
device for userspace management applications. Such an application is
therefore required to use this driver.

This patch implements basic MBIM support, reusing the NCM and WDM driver
APIs, currently limited to IP sessions with SessionID 0. DSS and
multiplexed IP sessions are not yet supported.
Signed-off-by: Greg Suarez <gsuarez@smithmicro.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move symbols and definitons which can be shared with a
MBIM driver in a new header.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

Adding multiplexed NDP support to cdc_ncm_fill_tx_frame, allowing
transmissions of multiple independent sessions within the same NTB.

Refactoring the code quite a bit to avoid having to store copies
of multiple NDPs being prepared for tx. The old code would still
reserve enough room for a maximum sized NDP in the skb so we might
as well keep them in the skb while they are being prepared.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

Verifying and handling received MBIM and NCM frames will need
to be different in three areas:
 - verifying the NDP signature
 - checking valid datagram length
 - datagram header manipulation

This makes it inconvenient to share rx_fixup in whole.  But
some verification parts are common.  Split these out in separate
functions.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

The NCM 1.0 spefication makes provisions for linking more than
one NDP into a single NTB. This is important for MBIM support,
where these NDPs might be of different types.

Following the chain of NDPs is also correct for NCM, and will
not change anything in the common case where there is only
one NDP
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

NCM and MBIM can share most of the bind function.  Split
out the shareable part and add MBIM functional descriptor
parsing.
Signed-off-by: Greg Suarez <gsuarez@smithmicro.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

MBIM and NCM are very similar, so we can reuse most of the
setup and bind logic in cdc_ncm for CDC MBIM devices.  Handle
a few minor differences in ncm_setup.
Signed-off-by: Greg Suarez <gsuarez@smithmicro.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

Based on revision 1.0 of "Universal Serial Bus Communications
Class Subclass Specification for Mobile Broadband Interface
Model" available from www.usb.org
Signed-off-by: Greg Suarez <gsuarez@smithmicro.com>
[bmork: added DSS defines]
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some devices do not support the 8 byte variants of the NTB input
size control messages despite announcing such support in their
NCM or MBIM functional descriptor.

According to the NCM specification, all devices must support the
4 byte variant regardless of whether or not the flag is set:

  If bit D5 is set in the bmNetworkCapabilities field of
  function’s NCM Functional Descriptor, the host may
  set wLength either to 4 or to 8. If wLength is 4, the
  function shall assume that wNtbInMaxDatagrams is to be
  set to zero. If wLength is 8, then the function shall
  use the provided value as the limit. The function shall
  return an error response (a STALL PID) if wLength is set
  to any other value.

We do not set wNtbInMaxDatagrams in any case, so we can just as
well unconditionally use the 4 byte variant without losing any
functionality.  This works around the known firmware bug, and
simplifies the code considerably.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

This will allow us to remove the last mach include from at91_ether
and also make it easier to share address setup with macb.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that HAVE_NET_MACB is gone let's just select MACB to
satisfy the dependecies in at91_ether.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

macb is a platform driver and there is nothing that prevents
this driver from being built on non-ARM/AVR32 platforms.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When building macb on x86_64 the following warnings show up:
  drivers/net/ethernet/cadence/macb.c: In function macb_interrupt:
  drivers/net/ethernet/cadence/macb.c:556:4: warning: large integer implicitly truncated to unsigned type [-Woverflow]
  drivers/net/ethernet/cadence/macb.c: In function macb_reset_hw:
  drivers/net/ethernet/cadence/macb.c:792:2: warning: large integer implicitly truncated to unsigned type [-Woverflow]
  drivers/net/ethernet/cadence/macb.c:793:2: warning: large integer implicitly truncated to unsigned type [-Woverflow]
  drivers/net/ethernet/cadence/macb.c:796:2: warning: large integer implicitly truncated to unsigned type [-Woverflow]

Use -1 insted of ~0UL, as done in other places in the driver,
to silence these warnings.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Each nexthop is added like a single route in the routing table. All routes
that have the same metric/weight and destination but not the same gateway
are considering as ECMP routes. They are linked together, through a list called
rt6i_siblings.

ECMP routes can be added in one shot, with RTA_MULTIPATH attribute or one after
the other (in both case, the flag NLM_F_EXCL should not be set).

The patch is based on a previous work from
Luc Saillard <luc.saillard@6wind.com>.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A small host typically needs ~10 fib_info structures, so create initial
hash table with 16 slots instead of only one. This removes potential
false sharing and reallocs/rehashes (1->2->4->8->16)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

SIOCINQ can use the lock_sock_fast() version to avoid double acquisition
of socket lock.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RFC 5961 5.2 [Blind Data Injection Attack].[Mitigation]

  All TCP stacks MAY implement the following mitigation.  TCP stacks
  that implement this mitigation MUST add an additional input check to
  any incoming segment.  The ACK value is considered acceptable only if
  it is in the range of ((SND.UNA - MAX.SND.WND) <= SEG.ACK <=
  SND.NXT).  All incoming segments whose ACK value doesn't satisfy the
  above condition MUST be discarded and an ACK sent back.

Move tcp_send_challenge_ack() before tcp_ack() to avoid a forward
declaration.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Jerry Chu <hkchu@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ns_to_ktime() seems better than ktime_set() + ktime_add_ns()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

FW flash layout on Skyhawk-R is different from BE3-R.
Hence the code needs to be fixed to flash FW on Skyhawk-R.
Also cleaning up code in BE3-R flashing function.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

be_shutdown is enabling wake-on-lan by calling be_setup_wol.
Emulex adapter do not support wake-on-lan in S5 state.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

PF driver should enable VF so that VF goes to ready state in
new Lancer FW.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

During PCI EEH, driver waits for all functions in the card.
Wait is needed only once per card. Fix is to wait only for the
first PCI function.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

During recovery from a FW error, destroy queue operation may fail.
Queue should be marked as destroyed so that recovery code can recreate
the queue. Also fix queue created state not getting checked at one instance.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Return default values for fields for which VFs dont have privilege to get the
required information from FW.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

VF does not have privileges to execute many commands. When VFs try
to execute those commands there are unnecessary error messages.
Fix this by executing only those commands for which VF has privilege.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow adding VLANs for Lancer VF.
VLAN ID 0 should not be added to list of VLANs sent to FW.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After FW error, driver should wait for NO_RESOURCE error to disappear before
proceeding with recovery.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For changing MAC of VF from PF, delete MAC operation needs to be done before
assigning new MAC. Also in ndo_set_mac_address operation avoid delete MAC if
it has been already deleted by PF.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use Lancer specific command to set QoS for VF.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Driver assumes FW resource counts and capabilities while creating queues and
using functionality like RSS. This causes driver load to fail in FW configs
where resources and capabilities are reduced. Fix this by querying FW
configuration during probe and using resources and capabilities accordingly.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch removes double assignment of err to -EINVAL in dev_change_net_namespace().
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Acked-by: Serge E. Hallyn <serge.hallyn@ubuntu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The SO_BINDTODEVICE option is the only SOL_SOCKET one that can be set, but
cannot be get via sockopt API. The only way we can find the device id a
socket is bound to is via sock-diag interface. But the diag works only on
hashed sockets, while the opt in question can be set for yet unhashed one.

That said, in order to know what device a socket is bound to (we do want
to know this in checkpoint-restore project) I propose to make this option
getsockopt-able and report the respective device index.

Another solution to the problem might be to teach the sock-diag reporting
info on unhashed sockets. Should I go this way instead?
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The struct sock *other one seem to be unused. Grep and make do not object.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the standard test for a non-zero ipv6 address.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Checked with Windows networking team, there is only one RNDIS message
in each netvsc packet.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
This series contains updates to ixgbe and igb.

Alexander Duyck (13):
  ixgbe: Initialize q_vector cpu and affinity masks correctly
  ixgbe: Enable jumbo frames support w/ SR-IOV
  ixgbe: Move message handling routines into their own functions
  ixgbe: Add mailbox API version negotiation support to ixgbe PF
  igb: Split Rx timestamping into two separate functions
  igb: Do not use header split, instead receive all frames into a
    single buffer
  igb: Combine post-processing of skb into a single function
  igb: Map entire page and sync half instead of mapping and unmapping
    half pages
  igb: Move rx_buffer related code in Rx cleanup path into separate
    function
  igb: Lock buffer size at 2K even on systems with larger pages
  igb: Combine q_vector and ring allocation into a single function
  igb: Move the calls to set the Tx and Rx queues into igb_open
  igb: Split igb_update_dca into separate Tx and Rx functions

Tushar Dave (1):
  igb: Correcting and improving small packet check and padding
====================
Signed-off-by: David S. Miller <davem@davemloft.net>