Following some discussion both on & off list, I have volunteered to take
over maintaining the miscellaneous RISC-V devicetrees & soc drivers from
Palmer to ease his load.

So far only SiFive and Microchip have stuff in drivers/soc. For the
former, a SiFive entry exists with a dead GitHub repo - so remove that
to avoid confusion since the patches for drivers/soc & devicetrees will
be routed via my tree & other drivers go through their subsystem trees.
The Microchip directory only contains a RISC-V driver for now, but is
likely to contain drivers for other archs in the future. To that end,
change the PolarFire SoC entry to specifically mention the RISC-V driver
& the new directory level entry does not mention an architecture.

CC: Arnd Bergmann <arnd@arndb.de>
CC: Nicolas Ferre <nicolas.ferre@microchip.com>
CC: Palmer Dabbelt <palmer@dabbelt.com>
Link: https://lore.kernel.org/linux-riscv/mhng-e4210f56-fcc3-4db8-abdb-d43b3ebe695d@palmer-ri-x1c9a/Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Link: https://lore.kernel.org/r/20221109212219.1598355-2-conor@kernel.orgSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'at91-fixes-6.1' of https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into arm/fixes

AT91 fixes for 6.1

It contains:
- signal name fix for a pin on SAMA7G5
- memory self-refresh fix for SAMA7G5 by avoid soft resetting AC
  DLL which can introduce glitches in RAM controller and lead to
  unexpected behavior
- led support fix for lan966x-pcb8291 board by enabling sgpio node

* tag 'at91-fixes-6.1' of https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
  ARM: at91: pm: avoid soft resetting AC DLL
  ARM: dts: lan966x: Enable sgpio on pcb8291
  ARM: dts: at91: sama7g5: fix signal name of pin PB2

Link: https://lore.kernel.org/r/20221110115411.180876-1-claudiu.beznea@microchip.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'qcom-arm64-fixes-for-6.1' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/fixes

Qualcomm ARM64 DTS fixes for 6.1

This fixes the APCS register region on IPQ8074 to not overlap
with adjacent nodes.

It lists the valid LDO modes on a variety of platforms, as this is not
required by the binding and implementation.

The reference clocks for the two UFS instances on SC8280XP are
corrected, to avoid relying on the state left by most versions of the
bootloader.

A number of issues are corrected with regards to the QMP PHY register
ranges on SC8280XP.

SC7280 gains a missing lpass reset region.

Lastly cluster idle is termporarily disabled on SM8250 to avoid issues
with booting the platform, until the last missing pieces lands.

* tag 'qcom-arm64-fixes-for-6.1' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
  arm64: dts: qcom: sm8250: Disable the not yet supported cluster idle state
  arm64: dts: qcom: sc7280: Add the reset reg for lpass audiocc on SC7280
  arm64: dts: qcom: sc8280xp: fix UFS PHY serdes size
  arm64: dts: qcom: sc8280xp: drop broken DP PHY nodes
  arm64: dts: qcom: sc8280xp: fix USB PHY PCS registers
  arm64: dts: qcom: sc8280xp: fix USB1 PHY RX1 registers
  arm64: dts: qcom: sc8280xp: fix USB0 PHY PCS_MISC registers
  arm64: dts: qcom: sc8280xp: correct ref clock for ufs_mem_phy
  arm64: dts: qcom: sc8280xp: fix ufs_card_phy ref clock
  arm64: dts: qcom: sm8350-hdk: Specify which LDO modes are allowed
  arm64: dts: qcom: sm8250-xperia-edo: Specify which LDO modes are allowed
  arm64: dts: qcom: sm8150-xperia-kumano: Specify which LDO modes are allowed
  arm64: dts: qcom: sc8280xp-crd: Specify which LDO modes are allowed
  arm64: dts: qcom: sa8295p-adp: Specify which LDO modes are allowed
  arm64: dts: qcom: sa8155p-adp: Specify which LDO modes are allowed
  Revert "arm64: dts: qcom: msm8996: add missing TCSR syscon compatible"
  arm64: dts: qcom: ipq8074: correct APCS register space size

Link: https://lore.kernel.org/r/20221110040635.795921-1-andersson@kernel.orgSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'juno-fix-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/fixes

Armv8 Juno fix for v6.1

Just a single fix to add the missing critical points in the thermal
zones that has been mandatory in the binding but was enforced in the
code recently.

* tag 'juno-fix-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
  arm64: dts: juno: Add thermal critical trip points

Link: https://lore.kernel.org/r/20221102140156.2758137-1-sudeep.holla@arm.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'scmi-fixes-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/fixes

Arm SCMI fixes for v6.1

A bunch of fixes to handle:
1. A possible resource leak in scmi_remove(). The returned error
   value gets ignored by the driver core and can remove the device and
   free the devm-allocated resources. As a simple solution to be able to
   easily backport, the bind attributes in the driver is suppressed as
   there is no need to support it. Additionally the remove path is cleaned
   up by adding device links between the core and the protocol devices
   so that a proper and complete unbinding happens.
2. A possible spin-loop in the SCMI transmit path in case of misbehaving
   platform firmware. A timeout is added to the existing loop so that
   the SCMI stack can bailout aborting the transmission with warnings.
3. Optional Rx channel correctly by reporting any memory errors instead
   of ignoring the same with other allowed errors.
4. The use of proper device for all the device managed allocations in the
   virtio transport.
5. Incorrect deferred_tx_wq release on the error paths by using devres
   API(devm_add_action_or_reset) to manage the release in the error path.

* tag 'scmi-fixes-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
  firmware: arm_scmi: Fix deferred_tx_wq release on error paths
  firmware: arm_scmi: Fix devres allocation device in virtio transport
  firmware: arm_scmi: Make Rx chan_setup fail on memory errors
  firmware: arm_scmi: Make tx_prepare time out eventually
  firmware: arm_scmi: Suppress the driver's bind attributes
  firmware: arm_scmi: Cleanup the core driver removal callback

Link: https://lore.kernel.org/r/20221102140142.2758107-1-sudeep.holla@arm.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

When thermnal zones are defined, trip points definitions are mandatory.
Define a couple of critical trip points for monitoring of existing
PMIC and SOC thermal zones.

This was lost between txt to yaml conversion and was re-enforced recently
via the commit 8c596324 ("dt-bindings: thermal: Fix missing required property")

Cc: Rob Herring <robh+dt@kernel.org>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Fixes: f7b636a8 ("arm64: dts: juno: add thermal zones for scpi sensors")
Link: https://lore.kernel.org/r/20221028140833.280091-8-cristian.marussi@arm.comSigned-off-by: Sudeep Holla <sudeep.holla@arm.com>

Use devres to allocate the dedicated deferred_tx_wq polling workqueue so
as to automatically trigger the proper resource release on error path.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 5a3b7185 ("firmware: arm_scmi: Add atomic mode support to virtio transport")
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20221028140833.280091-6-cristian.marussi@arm.comSigned-off-by: Sudeep Holla <sudeep.holla@arm.com>

SCMI virtio transport device managed allocations must use the main
platform device in devres operations instead of the channel devices.

Cc: Peter Hilber <peter.hilber@opensynergy.com>
Fixes: 46abe13b ("firmware: arm_scmi: Add virtio transport")
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20221028140833.280091-5-cristian.marussi@arm.comSigned-off-by: Sudeep Holla <sudeep.holla@arm.com>

SCMI Rx channels are optional and they can fail to be setup when not
present but anyway channels setup routines must bail-out on memory errors.

Make channels setup, and related probing, fail when memory errors are
reported on Rx channels.

Fixes: 5c8a47a5 ("firmware: arm_scmi: Make scmi core independent of the transport type")
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20221028140833.280091-4-cristian.marussi@arm.comSigned-off-by: Sudeep Holla <sudeep.holla@arm.com>

SCMI transports based on shared memory, at start of transmissions, have
to wait for the shared Tx channel area to be eventually freed by the
SCMI platform before accessing the channel. In fact the channel is owned
by the SCMI platform until marked as free by the platform itself and,
as such, cannot be used by the agent until relinquished.

As a consequence a badly misbehaving SCMI platform firmware could lock
the channel indefinitely and make the kernel side SCMI stack loop
forever waiting for such channel to be freed, possibly hanging the
whole boot sequence.

Add a timeout to the existent Tx waiting spin-loop so that, when the
system ends up in this situation, the SCMI stack can at least bail-out,
nosily warn the user, and abort the transmission.
Reported-by: YaxiongTian <iambestgod@outlook.com>
Suggested-by: YaxiongTian <iambestgod@outlook.com>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Cc: Etienne Carriere <etienne.carriere@linaro.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20221028140833.280091-3-cristian.marussi@arm.comSigned-off-by: Sudeep Holla <sudeep.holla@arm.com>

Suppress the capability to unbind the core SCMI driver since all the
SCMI stack protocol drivers depend on it.

Fixes: aa4f886f ("firmware: arm_scmi: add basic driver infrastructure for SCMI")
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20221028140833.280091-2-cristian.marussi@arm.comSigned-off-by: Sudeep Holla <sudeep.holla@arm.com>

Platform drivers .remove callbacks are not supposed to fail and report
errors. Such errors are indeed ignored by the core platform drivers
and the driver unbind process is anyway completed.

The SCMI core platform driver as it is now, instead, bails out reporting
an error in case of an explicit unbind request.

Fix the removal path by adding proper device links between the core SCMI
device and the SCMI protocol devices so that a full SCMI stack unbind is
triggered when the core driver is removed. The remove process does not
bail out anymore on the anomalous conditions triggered by an explicit
unbind but the user is still warned.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20221028140833.280091-1-cristian.marussi@arm.comSigned-off-by: Sudeep Holla <sudeep.holla@arm.com>

Add Jay Fang as the maintainer of the HiSilicon LPC BUS Driver, replacing
John Garry.
Signed-off-by: Jay Fang <f.fangjian@huawei.com>
Link: https://lore.kernel.org/r/20221028105434.1661264-1-f.fangjian@huawei.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Recent changes to the thermal framework has made the trip
points (trips) for thermal zones compulsory, which made
the Ux500 DTS files break validation and also stopped
probing because of similar changes to the code.

Fix this by adding an "outer bounding box": battery thermal
zones should not get warmer than 70 degress, then we will
shut down.

Fixes: 8c596324 ("dt-bindings: thermal: Fix missing required property")
Fixes: 3fd6d6e2 ("thermal/of: Rework the thermal device tree initialization")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: linux-pm@vger.kernel.org
Link: https://lore.kernel.org/r/20221030210854.346662-1-linus.walleij@linaro.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'imx-fixes-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes

i.MX fixes for 6.1:

- Fix imx93-pd driver to release resources when error occurs in probe.
- A series from Ioana Ciornei to add missing clock frequencies for MDIO
  controllers on LayerScape SoCs, so that the kernel driver can work
  independently from bootloader.
- A series from Li Jun to fix USB power domain setup in i.MX8MM/N device
  trees.
- Fix CPLD_Dn pull configuration for MX8Menlo board to avoid interfering
  with CPLD power off functionality.
- Fix ctrl_sleep_moci GPIO setup for verdin-imx8mp board.
- Fix DT schema check warnings on uSDHC clocks for imx8-ss-conn device
  tree.
- Fix up gpcv2 DT bindings to have an optional `power-domains` property.
- A couple of i.MX93 device tree fixes on S4MU interrupt and gpio-ranges
  of GPIO controllers.
- Keep PU regulator on for Quad and QuadPlus based imx6dl-yapp4 boards to
  work around a hardware design flaw in supply voltage distribution.
- Fix user push-button GPIO offset on imx6qdl-gw59 boards.

* tag 'imx-fixes-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  arm64: dts: ls208xa: specify clock frequencies for the MDIO controllers
  arm64: dts: ls1088a: specify clock frequencies for the MDIO controllers
  arm64: dts: lx2160a: specify clock frequencies for the MDIO controllers
  soc: imx: imx93-pd: Fix the error handling path of imx93_pd_probe()
  arm64: dts: imx93: correct gpio-ranges
  arm64: dts: imx93: correct s4mu interrupt names
  dt-bindings: power: gpcv2: add power-domains property
  arm64: dts: imx8: correct clock order
  ARM: dts: imx6dl-yapp4: Do not allow PM to switch PU regulator off on Q/QP
  ARM: dts: imx6qdl-gw59{10,13}: fix user pushbutton GPIO offset
  arm64: dts: imx8mn: Correct the usb power domain
  arm64: dts: imx8mn: remove otg1 power domain dependency on hsio
  arm64: dts: imx8mm: correct usb power domains
  arm64: dts: imx8mm: remove otg1/2 power domain dependency on hsio
  arm64: dts: verdin-imx8mp: fix ctrl_sleep_moci
  arm64: dts: imx8mm: Enable CPLD_Dn pull down resistor on MX8Menlo

Link: https://lore.kernel.org/r/20221101031547.GB125525@dragonSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Do not soft reset AC DLL as controller is buggy and this operation my
introduce glitches in the controller leading to undefined behavior.

Fixes: f0bbf179 ("ARM: at91: pm: add self-refresh support for sama7g5")
Depends-on: a02875c4 ("ARM: at91: pm: fix self-refresh for sama7g5")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20221026124114.985876-2-claudiu.beznea@microchip.com

Enable sgpio node on pcb8291 as this is needed to be able to control
the LEDs on this board. Otherwise the LEDs support on the board will
not be available.
On the other board pcb8309 the sgpio is already enabled because it
needed to access the SFP ports.

Fixes: 0b7baa1a ("ARM: dts: lan966x: add led configuration")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20221026174303.702919-1-horatiu.vultur@microchip.com

Up until now, the external MDIO controller frequency values relied
either on the default ones out of reset or on those setup by u-boot.
Let's just properly specify the MDC frequency in the DTS so that even
without u-boot's intervention Linux can drive the MDIO bus.

Fixes: 0420dde3 ("arm64: dts: ls208xa: add the external MDIO nodes")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Up until now, the external MDIO controller frequency values relied
either on the default ones out of reset or on those setup by u-boot.
Let's just properly specify the MDC frequency in the DTS so that even
without u-boot's intervention Linux can drive the MDIO bus.

Fixes: bbe75af7 ("arm64: dts: ls1088a: add external MDIO device nodes")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Up until now, the external MDIO controller frequency values relied
either on the default ones out of reset or on those setup by u-boot.
Let's just properly specify the MDC frequency in the DTS so that even
without u-boot's intervention Linux can drive the MDIO bus.

Fixes: 6e1b8fae ("arm64: dts: lx2160a: add emdio1 node")
Fixes: 5705b9dc ("arm64: dts: lx2160a: add emdio2 node")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

In imx93_pd_probe(); if an error occurs, some resources need to be released
as done in the remove function.

Fixes: 0a0f7cc2 ("soc: imx: add i.MX93 SRC power domain driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Per imx93-pinfunc.h and pinctrl-imx93.c, correct gpio-ranges.

Fixes: ec8b5b50 ("arm64: dts: freescale: Add i.MX93 dtsi support")
Reported-by: David Wolfe <david.wolfe@nxp.com>
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Per binding doc, interrupt names should be tx and rx.

Fixes: 0dfb380d ("arm64: dts: imx93: add s4 mu node")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Some pgc power-domain requires a parent power domain, so
add an optional power-domains property, otherwise there will be
dt check warning:
gpc@303a0000: pgc:power-domain@1: 'power-domains' does not match
any of the regexes: 'pinctrl-[0-9]+'

Fixes: 30af8513 ("dt-bindings: power: add defines for i.MX8MM power domains")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Per bindings/mmc/fsl-imx-esdhc.yaml, the clock order is ipg, ahb, per,
otherwise warning: "
mmc@5b020000: clock-names:1: 'ahb' was expected
mmc@5b020000: clock-names:2: 'per' was expected "

Fixes: 16c4ea75 ("arm64: dts: imx8: switch to new lpcg clock binding")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Fix our design flaw in supply voltage distribution on the Quad and QuadPlus
based boards.

The problem is that we supply the SoC cache (VDD_CACHE_CAP) from VDD_PU
instead of VDD_SOC. The VDD_PU internal regulator can be disabled by PM
if VPU or GPU is not used. If that happens the system freezes. To prevent
that configure the reg_pu regulator to be always on.

Fixes: 0de4ab81 ("ARM: dts: imx6dl-yapp4: Add Y Soft IOTA Crux/Crux+ board")
Cc: petrben@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Petr Benes <petr.benes@ysoft.com>
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The GW5910 and GW5913 have a user pushbutton that is tied to the
Gateworks System Controller GPIO offset 2. Fix the invalid offset of 0.

Fixes: 64bf0a0a ("ARM: dts: imx6qdl-gw: add Gateworks System Controller support")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

pgc_otg1 is actual the power domain of usb PHY, usb controller
is in hsio power domain, and pgc_otg1 is required to be powered
up to detect usb remote wakeup, so move the pgc_otg1 power domain
to the usb phy node.

Fixes: ea2b5af5 ("arm64: dts: imx8mn: put USB controller into power-domains")
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

pgc_otg1 is an independent power domain of hsio, it's for usb phy,
so remove hsio power domain from its node.

Fixes: 8b8ebec6 ("arm64: dts: imx8mn: add GPC node")
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

pgc_otg1/2 is actual the power domain of usb PHY, usb controller
is in hsio power domain, and pgc_otg1/2 is required to be powered
up to detect usb remote wakeup, so move the pgc_otg1/2 power domain
to the usb phy node.

Fixes: 01df28d8 ("arm64: dts: imx8mm: put USB controllers into power-domains")
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

pgc_otg1/2 are independent power domain of hsio, they for usb phy,
so remove hsio power domain dependency from its node.

Fixes: d39d4bb1 ("arm64: dts: imx8mm: add GPC node")
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The GPIO signaling ctrl_sleep_moci is currently handled as a gpio hog.
But the gpio-hog node is made a child of the wrong gpio controller.
Move it to the node representing gpio4 so that it actually works.

Without this carrier board components jumpered to use the signal are
unconditionally switched off.

Fixes: a39ed23b ("arm64: dts: freescale: add initial support for verdin imx8m plus")
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

To support the deeper cluster idle state for sm8250 platforms, some
additional synchronization is needed between the rpmh-rsc device and the
CPU cluster PM domain. Until that is supported, let's disable the cluster
idle state.

This fixes a problem that has been reported for the Qcom RB5 platform (see
below), but most likely other sm8250 platforms suffers from similar issues,
so let's make the fix generic for sm8250.

vreg_l11c_3p3: failed to enable: -ETIMEDOUT
qcom-rpmh-regulator 18200000.rsc:pm8150l-rpmh-regulators: ldo11: devm_regulator_register() failed, ret=-110
qcom-rpmh-regulator: probe of 18200000.rsc:pm8150l-rpmh-regulators failed with error -110
Reported-by: Amit Pundir <amit.pundir@linaro.org>
Fixes: 32bc936d ("arm64: dts: qcom: sm8250: Add cpuidle states")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Amit Pundir <amit.pundir@linaro.org>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221027115745.240516-1-ulf.hansson@linaro.org

Merge tag 'arm-soc/for-6.1/maintainers-fixes' of https://github.com/Broadcom/stblinux into arm/fixes

This pull request contains MAINTAINERS file updates for Broadcom
sections, please pull the following:

- Palmer updates the various Broadcom entries to use https instead of
  git for the git trees listed

* tag 'arm-soc/for-6.1/maintainers-fixes' of https://github.com/Broadcom/stblinux:
  MAINTAINERS: git://github -> https://github.com for broadcom

Link: https://lore.kernel.org/r/20221019185514.750684-1-f.fainelli@gmail.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

The signal name of pin PB2 with function F is FLEXCOM11_IO1
as it is defined in the datasheet.

Fixes: 7540629e ("ARM: dts: at91: add sama7g5 SoC DT and sama7g5-ek")
Signed-off-by: Mihai Sain <mihai.sain@microchip.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20221017083119.1643-1-mihai.sain@microchip.com

Pull kvm fixes from Paolo Bonzini:
 "RISC-V:

   - Fix compilation without RISCV_ISA_ZICBOM

   - Fix kvm_riscv_vcpu_timer_pending() for Sstc

  ARM:

   - Fix a bug preventing restoring an ITS containing mappings for very
     large and very sparse device topology

   - Work around a relocation handling error when compiling the nVHE
     object with profile optimisation

   - Fix for stage-2 invalidation holding the VM MMU lock for too long
     by limiting the walk to the largest block mapping size

   - Enable stack protection and branch profiling for VHE

   - Two selftest fixes

  x86:

   - add compat implementation for KVM_X86_SET_MSR_FILTER ioctl

  selftests:

   - synchronize includes between include/uapi and tools/include/uapi"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  tools: include: sync include/api/linux/kvm.h
  KVM: x86: Add compat handler for KVM_X86_SET_MSR_FILTER
  KVM: x86: Copy filter arg outside kvm_vm_ioctl_set_msr_filter()
  kvm: Add support for arch compat vm ioctls
  RISC-V: KVM: Fix kvm_riscv_vcpu_timer_pending() for Sstc
  RISC-V: Fix compilation without RISCV_ISA_ZICBOM
  KVM: arm64: vgic: Fix exit condition in scan_its_table()
  KVM: arm64: nvhe: Fix build with profile optimization
  KVM: selftests: Fix number of pages for memory slot in memslot_modification_stress_test
  KVM: arm64: selftests: Fix multiple versions of GIC creation
  KVM: arm64: Enable stack protection and branch profiling for VHE
  KVM: arm64: Limit stage2_apply_range() batch size to largest block
  KVM: arm64: Work out supported block level at compile time

This reverts commit 72a95859.

It broke reboots on big-endian MIPS and MIPS64 malta QEMU instances,
which use the syscon driver.  Little-endian is not effected, which means
likely it's important to handle regmap_get_val_endian() in this function
after all.

Fixes: 72a95859 ("mfd: syscon: Remove repetition of the regmap_get_val_endian()")
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Lee Jones <lee@kernel.org>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit bfca3dd3 ("kernel/utsname_sysctl.c: print kernel arch") added
a new entry to the uts_kern_table[] array, but didn't update the
UTS_PROC_xyz enumerators of older entries, breaking anything that used
them.

Which is admittedly not many cases: it's really just the two uses of
uts_proc_notify() in kernel/sys.c.  But apparently journald-systemd
actually uses this to detect hostname changes.
Reported-by: Torsten Hilbrich <torsten.hilbrich@secunet.com>
Fixes: bfca3dd3 ("kernel/utsname_sysctl.c: print kernel arch")
Link: https://lore.kernel.org/lkml/0c2b92a6-0f25-9538-178f-eee3b06da23f@secunet.com/
Link: https://linux-regtracking.leemhuis.info/regzbot/regression/0c2b92a6-0f25-9538-178f-eee3b06da23f@secunet.com/
Cc: Petr Vorel <pvorel@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull perf fixes from Borislav Petkov:

 - Fix raw data handling when perf events are used in bpf

 - Rework how SIGTRAPs get delivered to events to address a bunch of
   problems with it. Add a selftest for that too

* tag 'perf_urgent_for_v6.1_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  bpf: Fix sample_flags for bpf_perf_event_output
  selftests/perf_events: Add a SIGTRAP stress test with disables
  perf: Fix missing SIGTRAPs