Vladimir Oltean says:

====================
LAG offload for Ocelot DSA switches

This patch series reworks the ocelot switchdev driver such that it could
share the same implementation for LAG offload as the felix DSA driver.

Testing has been done in the following topology:

         +----------------------------------+
         | Board 1         br0              |
         |             +---------+          |
         |            /           \         |
         |            |           |         |
         |            |         bond0       |
         |            |        +-----+      |
         |            |       /       \     |
         |  eno0     swp0    swp1    swp2   |
         +---|--------|-------|-------|-----+
             |        |       |       |
             +--------+       |       |
               Cable          |       |
                         Cable|       |Cable
               Cable          |       |
             +--------+       |       |
             |        |       |       |
         +---|--------|-------|-------|-----+
         |  eno0     swp0    swp1    swp2   |
         |            |       \       /     |
         |            |        +-----+      |
         |            |         bond0       |
         |            |           |         |
         |            \           /         |
         |             +---------+          |
         | Board 2         br0              |
         +----------------------------------+

The same script can be run on both Board 1 and Board 2 to set this up:

ip link del bond0
ip link add bond0 type bond mode balance-xor miimon 1
OR
ip link add bond0 type bond mode 802.3ad
ip link set swp1 down && ip link set swp1 master bond0 && ip link set swp1 up
ip link set swp2 down && ip link set swp2 master bond0 && ip link set swp2 up
ip link del br0
ip link add br0 type bridge
ip link set bond0 master br0
ip link set swp0 master br0

Then traffic can be tested between eno0 of Board 1 and eno0 of Board 2.
====================

Link: https://lore.kernel.org/r/20210205220221.255646-1-olteanv@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The ocelot switch has been supporting LAG offload since its initial
commit, however felix could not make use of that, due to lack of a LAG
abstraction in DSA. Now that we have that, let's forward DSA's calls
towards the ocelot library, who will deal with setting up the bonding.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Given the following topology, and focusing only on Box A:

         Box A
         +----------------------------------+
         | Board 1         br0              |
         |             +---------+          |
         |            /           \         |
         |            |           |         |
         |            |         bond0       |
         |            |        +-----+      |
         |192.168.1.1 |       /       \     |
         |  eno0     swp0    swp1    swp2   |
         +---|--------|-------|-------|-----+
             |        |       |       |
             +--------+       |       |
               Cable          |       |
                         Cable|       |Cable
               Cable          |       |
             +--------+       |       |
             |        |       |       |
         +---|--------|-------|-------|-----+
         |  eno0     swp0    swp1    swp2   |
         |192.168.1.2 |       \       /     |
         |            |        +-----+      |
         |            |         bond0       |
         |            |           |         |
         |            \           /         |
         |             +---------+          |
         | Board 2         br0              |
         +----------------------------------+
         Box B

The assisted_learning_on_cpu_port logic will see that swp0 is bridged
with a "foreign interface" (bond0) and will therefore install all
addresses learnt by the software bridge towards bond0 (including the
address of eno0 on Box B) as static addresses towards the CPU port.

But that's not what we want - bond0 is not really a "foreign interface"
but one we can offload including L2 forwarding from/towards it. So we
need to refine our logic for assisted learning such that, whenever we
see an address learnt on a non-DSA interface, we search through the tree
for any port that offloads that non-DSA interface.

Some confusion might arise as to why we search through the whole tree
instead of just the local switch returned by dsa_slave_dev_lower_find.
Or a different angle of the same confusion: why does
dsa_slave_dev_lower_find(br_dev) return a single dp that's under br_dev
instead of the whole list of bridged DSA ports?

To answer the second question, it should be enough to install the static
FDB entry on the CPU port of a single switch in the tree, because
dsa_port_fdb_add uses DSA_NOTIFIER_FDB_ADD which ensures that all other
switches in the tree get notified of that address, and add the entry
themselves using dsa_towards_port().

This should help understand the answer to the first question: the port
returned by dsa_slave_dev_lower_find may not be on the same switch as
the ports that offload the LAG. Nonetheless, if the driver implements
.crosschip_lag_join and .crosschip_bridge_join as mv88e6xxx does, there
still isn't any reason for trapping addresses learnt on the remote LAG
towards the CPU, and we should prevent that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

At present there is an issue when ocelot is offloading a bonding
interface, but one of the links of the physical ports goes down. Traffic
keeps being hashed towards that destination, and of course gets dropped
on egress.

Monitor the netdev notifier events emitted by the bonding driver for
changes in the physical state of lower interfaces, to determine which
ports are active and which ones are no longer.

Then extend ocelot_get_bond_mask to return either the configured bonding
interfaces, or the active ones, depending on a boolean argument. The
code that does rebalancing only needs to do so among the active ports,
whereas the bridge forwarding mask and the logical port IDs still need
to look at the permanently bonded ports.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

It makes it a bit easier to read and understand the code that deals with
balancing the 16 aggregation codes among the ports in a certain LAG.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

We can now simplify the implementation by always using ocelot_get_bond_mask
to look up the other ports that are offloading the same bonding interface
as us.

In ocelot_set_aggr_pgids, the code had a way to uniquely iterate through
LAGs. We need to achieve the same behavior by marking each LAG as visited,
which we do now by using a temporary 32-bit "visited" bitmask. This is
ok and we do not need dynamic memory allocation, because we know that
this switch architecture will not have more than 32 ports (the PGID port
masks are 32-bit anyway).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The setup of logical port IDs is done in two places: from the inconclusively
named ocelot_setup_lag and from ocelot_port_lag_leave, a function that
also calls ocelot_setup_lag (which apparently does an incomplete setup
of the LAG).

To improve this situation, we can rename ocelot_setup_lag into
ocelot_setup_logical_port_ids, and drop the "lag" argument. It will now
set up the logical port IDs of all switch ports, which may be just
slightly more inefficient but more maintainable.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The index of the LAG is equal to the logical port ID that all the
physical port members have, which is further equal to the index of the
first physical port that is a member of the LAG.

The code gets a bit carried away with logic like this:

	if (a == b)
		c = a;
	else
		c = b;

which can be simplified, of course, into:

	c = b;

(with a being port, b being lp, c being lag)

This further makes the "lp" variable redundant, since we can use "lag"
everywhere where "lp" (logical port) was used. So instead of a "c = b"
assignment, we can do a complete deletion of b. Only one comment here:

		if (bond_mask) {
			lp = __ffs(bond_mask);
			ocelot->lags[lp] = 0;
		}

lp was clobbered before, because it was used as a temporary variable to
hold the new smallest port ID from the bond. Now that we don't have "lp"
any longer, we'll just avoid the temporary variable and zeroize the
bonding mask directly.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Since this code should be called from pure switchdev as well as from
DSA, we must find a way to determine the bonding mask not by looking
directly at the net_device lowers of the bonding interface, since those
could have different private structures.

We keep a pointer to the bonding upper interface, if present, in struct
ocelot_port. Then the bonding mask becomes the bitwise OR of all ports
that have the same bonding upper interface. This adds a duplication of
functionality with the current "lags" array, but the duplication will be
short-lived, since further patches will remove the latter completely.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

IPv6 header information is not currently part of the entropy source for
the 4-bit aggregation code used for LAG offload, even though it could be.
The hardware reference manual says about these fields:

ANA::AGGR_CFG.AC_IP6_TCPUDP_PORT_ENA
Use IPv6 TCP/UDP port when calculating aggregation code. Configure
identically for all ports. Recommended value is 1.

ANA::AGGR_CFG.AC_IP6_FLOW_LBL_ENA
Use IPv6 flow label when calculating AC. Configure identically for all
ports. Recommended value is 1.

Integration with the xmit_hash_policy of the bonding interface is TBD.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Since switchdev/DSA exposes network interfaces that fulfill many of the
same user space expectations that dedicated NICs do, it makes sense to
not deny bonding interfaces with a bonding policy that we cannot offload,
but instead allow the bonding driver to select the egress interface in
software.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Make ocelot's net device event handler more streamlined by structuring
it in a similar way with others. The inspiration here was
dsa_slave_netdevice_event.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

ocelot_netdevice_port_event treats a single event, NETDEV_CHANGEUPPER.
So we can remove the check for the type of event, and rename the
function to be more suggestive, since there already is a function with a
very similar name of ocelot_netdevice_event.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Vladimir Oltean says:

====================
Automatically manage DSA master interface state

This patch series adds code that makes DSA open the master interface
automatically whenever one user interface gets opened, either by the
user, or by various networking subsystems: netconsole, nfsroot.
With that in place, we can remove some of the places in the network
stack where DSA-specific code was sprinkled.
====================

Link: https://lore.kernel.org/r/20210205133713.4172846-1-vladimir.oltean@nxp.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

This reverts commit 728c0208.

Since 2015 DSA has gained more integration with the network stack, we
can now have the same functionality without explicitly open-coding for
it:
- It now opens the DSA master netdevice automatically whenever a user
  netdevice is opened.
- The master and switch interfaces are coupled in an upper/lower
  hierarchy using the netdev adjacency lists.

In the nfsroot example below, the interface chosen by autoconfig was
swp3, and every interface except that and the DSA master, eth1, was
brought down afterwards:

[    8.714215] mscc_felix 0000:00:00.5 swp0 (uninitialized): PHY [0000:00:00.3:10] driver [Microsemi GE VSC8514 SyncE] (irq=POLL)
[    8.978041] mscc_felix 0000:00:00.5 swp1 (uninitialized): PHY [0000:00:00.3:11] driver [Microsemi GE VSC8514 SyncE] (irq=POLL)
[    9.246134] mscc_felix 0000:00:00.5 swp2 (uninitialized): PHY [0000:00:00.3:12] driver [Microsemi GE VSC8514 SyncE] (irq=POLL)
[    9.486203] mscc_felix 0000:00:00.5 swp3 (uninitialized): PHY [0000:00:00.3:13] driver [Microsemi GE VSC8514 SyncE] (irq=POLL)
[    9.512827] mscc_felix 0000:00:00.5: configuring for fixed/internal link mode
[    9.521047] mscc_felix 0000:00:00.5: Link is Up - 2.5Gbps/Full - flow control off
[    9.530382] device eth1 entered promiscuous mode
[    9.535452] DSA: tree 0 setup
[    9.539777] printk: console [netcon0] enabled
[    9.544504] netconsole: network logging started
[    9.555047] fsl_enetc 0000:00:00.2 eth1: configuring for fixed/internal link mode
[    9.562790] fsl_enetc 0000:00:00.2 eth1: Link is Up - 1Gbps/Full - flow control off
[    9.564661] 8021q: adding VLAN 0 to HW filter on device bond0
[    9.637681] fsl_enetc 0000:00:00.0 eth0: PHY [0000:00:00.0:02] driver [Qualcomm Atheros AR8031/AR8033] (irq=POLL)
[    9.655679] fsl_enetc 0000:00:00.0 eth0: configuring for inband/sgmii link mode
[    9.666611] mscc_felix 0000:00:00.5 swp0: configuring for inband/qsgmii link mode
[    9.676216] 8021q: adding VLAN 0 to HW filter on device swp0
[    9.682086] mscc_felix 0000:00:00.5 swp1: configuring for inband/qsgmii link mode
[    9.690700] 8021q: adding VLAN 0 to HW filter on device swp1
[    9.696538] mscc_felix 0000:00:00.5 swp2: configuring for inband/qsgmii link mode
[    9.705131] 8021q: adding VLAN 0 to HW filter on device swp2
[    9.710964] mscc_felix 0000:00:00.5 swp3: configuring for inband/qsgmii link mode
[    9.719548] 8021q: adding VLAN 0 to HW filter on device swp3
[    9.747811] Sending DHCP requests ..
[   12.742899] mscc_felix 0000:00:00.5 swp1: Link is Up - 1Gbps/Full - flow control rx/tx
[   12.743828] mscc_felix 0000:00:00.5 swp0: Link is Up - 1Gbps/Full - flow control off
[   12.747062] IPv6: ADDRCONF(NETDEV_CHANGE): swp1: link becomes ready
[   12.755216] fsl_enetc 0000:00:00.0 eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[   12.766603] IPv6: ADDRCONF(NETDEV_CHANGE): swp0: link becomes ready
[   12.783188] mscc_felix 0000:00:00.5 swp2: Link is Up - 1Gbps/Full - flow control rx/tx
[   12.785354] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   12.799535] IPv6: ADDRCONF(NETDEV_CHANGE): swp2: link becomes ready
[   13.803141] mscc_felix 0000:00:00.5 swp3: Link is Up - 1Gbps/Full - flow control rx/tx
[   13.811646] IPv6: ADDRCONF(NETDEV_CHANGE): swp3: link becomes ready
[   15.452018] ., OK
[   15.470336] IP-Config: Got DHCP answer from 10.0.0.1, my address is 10.0.0.39
[   15.477887] IP-Config: Complete:
[   15.481330]      device=swp3, hwaddr=00:04:9f:05:de:0a, ipaddr=10.0.0.39, mask=255.255.255.0, gw=10.0.0.1
[   15.491846]      host=10.0.0.39, domain=(none), nis-domain=(none)
[   15.498429]      bootserver=10.0.0.1, rootserver=10.0.0.1, rootpath=
[   15.498481]      nameserver0=8.8.8.8
[   15.627542] fsl_enetc 0000:00:00.0 eth0: Link is Down
[   15.690903] mscc_felix 0000:00:00.5 swp0: Link is Down
[   15.745216] mscc_felix 0000:00:00.5 swp1: Link is Down
[   15.800498] mscc_felix 0000:00:00.5 swp2: Link is Down
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This reverts commit 1532b977.

The above commit is good and it works, however it was meant as a bugfix
for stable kernels and now we have more self-contained ways in DSA to
handle the situation where the DSA master must be brought up.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This is not fixing any actual bug that I know of, but having a DSA
interface that is up even when its lower (master) interface is down is
one of those things that just do not sound right.

Yes, DSA checks if the master is up before actually bringing the
user interface up, but nobody prevents bringing the master interface
down immediately afterwards... Then the user ports would attempt
dev_queue_xmit on an interface that is down, and wonder what's wrong.

This patch prevents that from happening. NETDEV_GOING_DOWN is the
notification emitted _before_ the master actually goes down, and we are
protected by the rtnl_mutex, so all is well.

For those of you reading this because you were doing switch testing
such as latency measurements for autonomously forwarded traffic, and you
needed a controlled environment with no extra packets sent by the
network stack, this patch breaks that, because now the user ports go
down too, which may shut down the PHY etc. But please don't do it like
that, just do instead:

tc qdisc add dev eno2 clsact
tc filter add dev eno2 egress flower action drop

Tested with two cascaded DSA switches:
$ ip link set eno2 down
sja1105 spi2.0 sw0p2: Link is Down
mscc_felix 0000:00:00.5 swp0: Link is Down
fsl_enetc 0000:00:00.2 eno2: Link is Down
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

DSA wants the master interface to be open before the user port is due to
historical reasons. The promiscuity of interfaces that are down used to
have issues, as referenced Lennert Buytenhek in commit df02c6ff
("dsa: fix master interface allmulti/promisc handling").

The bugfix mentioned there, commit b6c40d68 ("net: only invoke
dev->change_rx_flags when device is UP"), was basically a "don't do
that" approach to working around the promiscuity while down issue.

Further work done by Vlad Yasevich in commit d2615bf4 ("net: core:
Always propagate flag changes to interfaces") has resolved the
underlying issue, and it is strictly up to the DSA and 8021q drivers
now, it is no longer mandated by the networking core that the master
interface must be up when changing its promiscuity.

From DSA's point of view, deciding to error out in dsa_slave_open
because the master isn't up is
(a) a bad user experience and
(b) knocking at an open door.
Even if there still was an issue with promiscuity while down, DSA could
still just open the master and avoid it.

Doing it this way has the additional benefit that user space can now
remove DSA-specific workarounds, like systemd-networkd with BindCarrier:
https://github.com/systemd/systemd/issues/7478

And we can finally remove one of the 2 bullets in the "Common pitfalls
using DSA setups" chapter.

Tested with two cascaded DSA switches:

$ ip link set sw0p2 up
fsl_enetc 0000:00:00.2 eno2: configuring for fixed/internal link mode
fsl_enetc 0000:00:00.2 eno2: Link is Up - 1Gbps/Full - flow control rx/tx
mscc_felix 0000:00:00.5 swp0: configuring for fixed/sgmii link mode
mscc_felix 0000:00:00.5 swp0: Link is Up - 1Gbps/Full - flow control off
8021q: adding VLAN 0 to HW filter on device swp0
sja1105 spi2.0 sw0p2: configuring for phy/rgmii-id link mode
IPv6: ADDRCONF(NETDEV_CHANGE): eno2: link becomes ready
IPv6: ADDRCONF(NETDEV_CHANGE): swp0: link becomes ready
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Huazhong Tan says:

====================
net: hns3: updates for -next

This series adds some code optimizations and compatibility
handlings for the HNS3 ethernet driver.

change log:
V2: refactor #2 as Jukub Kicinski reported and remove the part
    about RSS size which will not be different in different hw.
    updates netdev->max_mtu as well in #4 reported by Jakub Kicinski.

previous version:
V1: https://patchwork.kernel.org/project/netdevbpf/cover/1612269593-18691-1-git-send-email-tanhuazhong@huawei.com/
====================

Link: https://lore.kernel.org/r/1612513969-9278-1-git-send-email-tanhuazhong@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The max qset number is a fixed value now and it is defined by a macro.
In order to support other value in different kinds of device, it is
better to use specification queried from firmware to replace macro.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In order to add a method to check the specification of max tm rate
for debugging, function hns3_dbg_dev_specs() adds this value print.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Since the newer hardware may supports different frame size,
so add support to obtain the capability from the firmware
instead of the fixed value.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

When update the TC info for NIC, there are some differences
between PF and VF. Currently, four "vport->vport_id" are
used to distinguish PF or VF. So merge them into one to
improve readability and maintainability of code.
Signed-off-by: GuoJia Liao <liaoguojia@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

As RSS indirection table size may be different in different
hardware. Instead of using macro, this value is better to use
device specification which querying from firmware.

BTW, RSS indirection table should be allocated by the queried
size instead the static array.

.get_rss_indir_size in struct hnae3_ae_ops is not used now,
so remove it as well.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

To improve the compatibility of firmware for driver, help firmware
to deal with different api commands, add api capability bits when
initialize the command queue.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Mat Martineau says:

====================
mptcp: Misc. updates for tests & lock annotation

Here are two fixes we've collected in the mptcp tree.

Patch 1 refactors a MPTCP selftest script to allow running a subset of
the tests.

Patch 2 adds some locking & might_sleep assertations.
====================

Link: https://lore.kernel.org/r/20210204232330.202441-1-mathew.j.martineau@linux.intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Add a few assertions to make sure functions are called with the needed
locks held.
Two functions gain might_sleep annotations because they contain
conditional calls to functions that sleep.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Since the mptcp_join script is becoming too big, this patch splits it
into several smaller chunks, each of them has been defined in a function
as a individual test group for several related testcases.

Using bash getopts function to parse command line arguments, and invoke
each function to do the individual test group.

Here are all the arguments:
  -f subflows_tests
  -s signal_address_tests
  -l link_failure_tests
  -t add_addr_timeout_tests
  -r remove_tests
  -a add_tests
  -6 ipv6_tests
  -4 v4mapped_tests
  -b backup_tests
  -p add_addr_ports_tests
  -c syncookies_tests
  -h help

Run mptcp_join.sh with no argument will execute all testcases.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Russell King says:

====================
dpaa2: add 1000base-X support

This patch series adds 1000base-X support to pcs-lynx and DPAA2,
allowing runtime switching between SGMII and 1000base-X. This is
a pre-requisit for SFP module support on the SolidRun ComExpress 7.

v2: updated with Ioana's r-b's, and comment on backplane support
====================

Link: https://lore.kernel.org/r/20210205103859.GH1463@shell.armlinux.org.ukSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Add support for backplane link mode, which is, according to discussions
with NXP earlier in the year, is a mode where the OS (Linux) is able to
manage the PCS and Serdes itself.

This commit prepares the ground work for allowing 1G fiber connections
to be used with DPAA2 on the SolidRun CEX7 platforms.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Now that pcs-lynx supports 1000BASE-X, add support for this interface
mode to dpaa2-mac. pcs-lynx can be switched at runtime between SGMII
and 1000BASE-X mode, so allow dpaa2-mac to switch between these as
well.

This commit prepares the ground work for allowing 1G fiber connections
to be used with DPAA2 on the SolidRun CEX7 platforms.
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add support for 1000BASE-X to pcs-lynx for the LX2160A.

This commit prepares the ground work for allowing 1G fiber connections
to be used with DPAA2 on the SolidRun CEX7 platforms.
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This converts the driver to use the new tasklet API introduced in
commit 12cc923f ("tasklet: Introduce new initialization API")

The new API changes the argument passed to callback functions,
but fortunately it is unused so it is straight forward to use
DECLARE_TASKLET rather than DECLARE_TASLKLET_OLD.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Link: https://lore.kernel.org/r/20210204173947.92884-1-kernel@esmil.dkSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Kevin Hao says:

====================
net: Avoid the memory waste in some Ethernet drivers

In the current implementation of napi_alloc_frag(), it doesn't have any
align guarantee for the returned buffer address. We would have to use
some ugly workarounds to make sure that we can get a align buffer
address for some Ethernet drivers. This patch series tries to introduce
some helper functions to make sure that an align buffer is returned.
Then we can drop the ugly workarounds and avoid the unnecessary memory
waste.
====================

Link: https://lore.kernel.org/r/20210204105638.1584-1-haokexin@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The napi_alloc_frag_align() will guarantee that a correctly align
buffer address is returned. So use this function to simplify the buffer
alloc and avoid the unnecessary memory waste.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The napi_alloc_frag_align() will guarantee that a correctly align
buffer address is returned. So use this function to simplify the buffer
alloc and avoid the unnecessary memory waste.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Tested-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In the current implementation of {netdev,napi}_alloc_frag(), it doesn't
have any align guarantee for the returned buffer address, But for some
hardwares they do require the DMA buffer to be aligned correctly,
so we would have to use some workarounds like below if the buffers
allocated by the {netdev,napi}_alloc_frag() are used by these hardwares
for DMA.
    buf = napi_alloc_frag(really_needed_size + align);
    buf = PTR_ALIGN(buf, align);

These codes seems ugly and would waste a lot of memories if the buffers
are used in a network driver for the TX/RX. We have added the align
support for the page_frag functions, so add the corresponding
{netdev,napi}_frag functions.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In the current implementation of page_frag_alloc(), it doesn't have
any align guarantee for the returned buffer address. But for some
hardwares they do require the DMA buffer to be aligned correctly,
so we would have to use some workarounds like below if the buffers
allocated by the page_frag_alloc() are used by these hardwares for
DMA.
    buf = page_frag_alloc(really_needed_size + align);
    buf = PTR_ALIGN(buf, align);

These codes seems ugly and would waste a lot of memories if the buffers
are used in a network driver for the TX/RX. So introduce
page_frag_alloc_align() to make sure that an aligned buffer address is
returned.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

There is a spelling mistake in the function name alloc_channles_and_rings.
Fix this by renaming it to alloc_channels_and_rings.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210204094944.51460-1-colin.king@canonical.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

When device side MTU is larger than host side MTU, the packets
(typically rmnet packets) are split over multiple MHI transfers.
In that case, fragments must be re-aggregated to recover the packet
before forwarding to upper layer.

A fragmented packet result in -EOVERFLOW MHI transaction status for
each of its fragments, except the final one. Such transfer was
previously considered as error and fragments were simply dropped.

This change adds re-aggregation mechanism using skb chaining, via
skb frag_list.

A warning (once) is printed since this behavior usually comes from
a misconfiguration of the device (e.g. modem MTU).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/1612428002-12333-1-git-send-email-loic.poulain@linaro.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>