The code really means to mask off the high bits, not assign 0xff.

Reported by Marcus Meissner <meissner@suse.de>.
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>

During an STR resume cycle, the ide master disk times-out when there is
also a slave present (especially CD).  Increasing the timeout in ide-io
from 10,000 to 100,000 fixes this problem.
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Adrian Bunk <bunk@stusta.de>

Something is wrong with the 3-multiply (vs. 4-multiply) optimized
version of _FP_MUL_MEAT_2_*(), so just use the slower version
which actually computes correct values.

Noticed by Rene Rebe
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Adrian Bunk <bunk@stusta.de>

Fix the calculation of the end address when flushing iotlb entries to
ram.  This bug has been a cause of esp dma errors, and it affects
HyperSPARC systems much worse than SuperSPARC systems.
Signed-off-by: Bob Breuer <breuerr@mc.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: William Lee Irwin III <wli@holomorphy.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>

The i386 defconfig wasn't updated for ages.

Instead of running "make oldconfig" on the old defconfig and trying to
give reasonable answers at all new options, this patch replaces it with
the one I'm using in 2.6.16-rc1.

This way, it's a .config that is confirmed to work on at least one
computer in the world.  ;-)
Signed-off-by: Adrian Bunk <bunk@stusta.de>

At least Maxtor OneTouch III require a "start stop unit" command after
auto spin-down before the next access can proceed.  This patch activates
the responsible code in scsi_mod for all Maxtor SBP-2 disks.
https://bugzilla.novell.com/show_bug.cgi?id=183011

Maybe that should be done for all SBP-2 disks, but better be cautious.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>

I've been experimenting to track down the cause of suspend/resume problems
on my Compaq Presario X1050 laptop:

http://bugzilla.kernel.org/show_bug.cgi?id=6075

Essentially the ACPI Embedded Controller and keyboard controller would
get into a bizarre, confused state after resume.

I found that unloading the ohci1394 module before suspend and reloading it
after resume made the problem go away.  Diffing the dmesg output from
resume, with and without the module loaded, I found that with the module
loaded I was missing these:

PM: Writing back config space on device 0000:02:00.0 at offset 1. (Was 2100080, writing 2100007)
PM: Writing back config space on device 0000:02:00.0 at offset 3. (Was 0, writing 8008)
PM: Writing back config space on device 0000:02:00.0 at offset 4. (Was 0, writing 90200000)
PM: Writing back config space on device 0000:02:00.0 at offset 5. (Was 1, writing 2401)
PM: Writing back config space on device 0000:02:00.0 at offset f. (Was 20000100, writing 2000010a)

The default PCI driver performs the pci_restore_state when no driver is
loaded for the device.  When the ohci1394 driver is loaded, it is supposed
to do this, however it appears not to do so.

I created the patch below and tested it, and it appears to resolve the
suspend problems I was having with the module loaded.  I only added in the
pci_save_state and pci_restore_state - however, though I know little of
this hardware, surely the driver should really be doing more than this when
suspending and resuming?  Currently it does almost nothing, what if there
are commands in progress, etc?
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>

Looking at the reiser4 crash, I found a leak in debugfs. In
debugfs_mknod(), we create the inode before checking if the dentry
already has one attached. We don't free it if that is the case.
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>

If get_user_pages() returns less pages than what we asked for, we
jump to out_unmap which will return ERR_PTR(ret). But ret can contain
a positive number just smaller than local_nr_pages, so be sure to set
it to -EFAULT always.

Problem found and diagnosed by Damien Le Moal <damien@sdl.hitachi.co.jp>
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>

kernel.org bugzilla #6206

Based on patch from Serge Belyshev <belyshev@depni.sinp.msu.ru>
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>

Due to a regression in the correcponding ALSA driver (ALSA #2234), the
OSS driver should stay until it's fixed.
Signed-off-by: Adrian Bunk <bunk@stusta.de>

ieee80211_crypt_tkip will not work without CRC32.

  LD      .tmp_vmlinux1
net/built-in.o: In function `ieee80211_tkip_encrypt':
net/ieee80211/ieee80211_crypt_tkip.c:349: undefined reference to `crc32_le'

Reported by Toralf Foerster <toralf.foerster@gmx.de>
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>

Memory hotplug code of i386 adds memory to only highmem.  So, if
CONFIG_HIGHMEM is not set, CONFIG_MEMORY_HOTPLUG shouldn't be set.
Otherwise, it causes compile error.

In addition, many architecture can't use memory hotplug feature yet.  So, I
introduce CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG.
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>

2.6.16 needs this. It was merged into 2.6.18-rc1.

pdflush is carefully designed to ensure that all wakeups have some
corresponding work to do - if a woken-up pdflush thread discovers that
it hasn't been given any work to do then this is considered an error.

That all broke when swsusp came along - because a timer-delivered
wakeup to a frozen pdflush thread will just get lost.  This causes the
pdflush thread to get lost as well: the writeback timer is supposed to
be re-armed by pdflush in process context, but pdflush doesn't execute
the callout which does this.

Fix that up by ignoring the return value from try_to_freeze(): jsut
proceed, see if we have any work pending and only go back to sleep if
that is not the case.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Adrian Bunk <bunk@stusta.de>

This fixes some OOMs on 64bit systems with <4GB of RAM when accessing
the cdrom.

Do a safer check for when to enable DMA. Currently we enable ISA DMA
for cases that do not need it, resulting in OOM conditions when ZONE_DMA
runs out of space.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>

mthca does not restore the following PCI-X/PCI Express registers after reset:
  PCI-X device: PCI-X command register
  PCI-X bridge: upstream and downstream split transaction registers
  PCI Express : PCI Express device control and link control registers

This causes instability and/or bad performance on systems where one of
these registers is set to a non-default value by BIOS.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Adrian Bunk <bunk@stusta.de>

CONFIG_SND_FM801=y, CONFIG_SND_FM801_TEA575X=m resulted in the following
compile error:

<--  snip  -->

...
  LD      vmlinux
sound/built-in.o: In function 'snd_fm801_free':
fm801.c:(.text+0x3c15b): undefined reference to 'snd_tea575x_exit'
sound/built-in.o: In function 'snd_card_fm801_probe':
fm801.c:(.text+0x3cfde): undefined reference to 'snd_tea575x_init'
make: *** [vmlinux] Error 1

<--  snip  -->

This patch fixes kernel Bugzilla #6458.
Signed-off-by: Adrian Bunk <bunk@stusta.de>

Remove SWSUSP_ENCRYPT config option; it is no longer implemented.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Adrian Bunk <bunk@stusta.de>

This patch limits the amount of outstanding 'write' data that can be
queued up for the ftdi_sio driver, to prevent userspace DoS attacks (or
simple accidents) that use up all the system memory by writing lots of
data to the serial port.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

We need to update hiscore.rule even if we don't enable CONFIG_IPV6_PRIVACY,
because we have more less significant rule; longest match.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Two additional labels (RFC 3484, sec. 10.3) for IPv6 addreses
are defined to make a distinction between global unicast
addresses and Unique Local Addresses (fc00::/7, RFC 4193) and
Teredo (2001::/32, RFC 4380). It is necessary to avoid attempts
of connection that would either fail (eg. fec0:: to 2001:feed::)
or be sub-optimal (2001:0:: to 2001:feed::).
Signed-off-by: $,1 aukasz Stelmach <stlman@poczta.fm>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Relax /proc fix a bit

Clearign all of i_mode was a bit draconian. We only really care about
S_ISUID/ISGID, after all.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Fix nasty /proc vulnerability

We have a bad interaction with both the kernel and user space being able
to change some of the /proc file status.  This fixes the most obvious
part of it, but I expect we'll also make it harder for users to modify
even their "own" files in /proc.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Based on a patch from Ernie Petrides

During security research, Red Hat discovered a behavioral flaw in core
dump handling. A local user could create a program that would cause a
core file to be dumped into a directory they would not normally have
permissions to write to. This could lead to a denial of service (disk
consumption), or allow the local user to gain root privileges.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Should have not been applied to 2.6.16
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

When a packet without any chunks is received, the newconntrack variable
in sctp_packet contains an out of bounds value that is used to look up an
pointer from the array of timeouts, which is then dereferenced, resulting
in a crash. Make sure at least a single chunk is present.

Problem noticed by George A. Theall <theall@tenablesecurity.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

It fixes a crash in NTFS on architectures where flush_dcache_page()
is a real function.  I never noticed this as all my testing is done on
i386 where flush_dcache_page() is NULL.

http://bugzilla.kernel.org/show_bug.cgi?id=6700

Many thanks to Pauline Ng for the detailed bug report and analysis!
Signed-off-by: Anton Altaparmakov <aia21@cantab.net>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>

Work around the oops reported in
http://bugzilla.kernel.org/show_bug.cgi?id=6478.

Thanks to Ralf Hildebrandt <ralf.hildebrandt@charite.de> for testing and
reporting.
Acked-by: Dave Jones <davej@codemonkey.org.uk>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

- Fixed locking of struct i2o_exec_wait in Executive-OSM

- Removed LCT Notify in i2o_exec_probe() which caused freeing memory and
  accessing freed memory during first enumeration of I2O devices

- Added missing locking in i2o_exec_lct_notify()

- removed put_device() of I2O controller in i2o_iop_remove() which caused
  the controller structure get freed to early

- Fixed size of mempool in i2o_iop_alloc()

- Fixed access to freed memory in i2o_msg_get()

See http://bugzilla.kernel.org/show_bug.cgi?id=6561Signed-off-by: Markus Lidel <Markus.Lidel@shadowconnect.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The calculation of nr_pages in scsi_req_map_sg() doesn't account for
the fact that the first page could have an offset that pushes the end
of the buffer onto a new page.
Signed-off-by: Bryan Holty <lgeek@frontiernet.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

It looks like metapage_releasepage was making in invalid assumption that
the releasepage method would not be called on a dirty page.  Instead of
issuing a warning and releasing the metapage, it should return 0, indicating
that the private data for the page cannot be released.

I also realized that metapage_releasepage had the return code all wrong.  If
it is successful in releasing the private data, it should return 1, otherwise
it needs to return 0.

Lastly, there is no need to call wait_on_page_writeback, since
try_to_release_page will not call us with a page in writback state.
Signed-off-by: Dave Kleikamp <shaggy@austin.ibm.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

We're presently running lock_kernel() under fs_lock via nfs's ->permission
handler.  That's a ranking bug and sometimes a sleep-in-spinlock bug.  This
problem was introduced in the openat() patchset.

We should not need to hold the current->fs->lock for a codepath that doesn't
use current->fs.

[vsu@altlinux.ru: fix error path]
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: Al Viro <viro@ftp.linux.org.uk>
Signed-off-by: Sergey Vlasov <vsu@altlinux.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

I noticed a strange behavior in a tmpfs file system the other day, while
building packages - occasionally, and seemingly at random, make decided to
rebuild a target. However, only on tmpfs.

A file would be created, and if checked, it had a sub-second timestamp.
However, after an utimes related call where sub-seconds should be set, they
were zeroed instead. In the case that a file was created, and utimes(...,NULL)
was used on it in the same second, the timestamp on the file moved backwards.

After some digging, I found that this was being caused by tmpfs not having a
time granularity set, thus inheriting the default 1 second granularity.

Hugh adds: yes, we missed tmpfs when the s_time_gran mods went into 2.6.11.
Unfortunately, the granularity of CURRENT_TIME, often used in filesystems,
does not match the default granularity set by alloc_super.  A few more such
discrepancies have been found, but this is the most important to fix now.
Signed-off-by: Robin H. Johnson <robbat2@gentoo.org>
Acked-by: Andi Kleen <ak@suse.de>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>