- 04 Aug, 2022 3 commits
-
-
Karol Herbst authored
Appears to be ok with general GA10x code. Signed-off-by:
Karol Herbst <kherbst@redhat.com> Cc: <stable@vger.kernel.org> # v5.15+ Reviewed-by:
Lyude Paul <lyude@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220803142745.2679510-1-kherbst@redhat.com
-
Timur Tabi authored
This check determines whether a given address is part of image 0 or image 1. Image 1 starts at offset image0_size, so that address should be included. Fixes: 4d4e9907 ("drm/nouveau/bios: guard against out-of-bounds accesses to image") Signed-off-by:
Timur Tabi <ttabi@nvidia.com> Reviewed-by:
-
Laurentiu Palcu authored
When DCSS + MIPI_DSI is used, and the last bridge in the chain supports HPD, we can see a "Hot plug detection already enabled" warning stack trace dump that's thrown when DCSS is initialized. The problem appeared when HPD was enabled by default in the bridge_connector initialization, which made the drm_bridge_connector_enable_hpd() call, in DCSS init path, redundant. So, let's remove that call. Fixes: 09077bc3 ("drm/bridge_connector: enable HPD by default if supported") Signed-off-by:
Laurentiu Palcu <laurentiu.palcu@oss.nxp.com> Reviewed-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220721120912.6639-1-laurentiu.palcu@oss.nxp.com
-
- 28 Jul, 2022 1 commit
-
-
Alistair Popple authored
Users may request that pages from an OpenCL SVM allocation be migrated to the GPU with clEnqueueSVMMigrateMem(). In Nouveau this will call into nouveau_dmem_migrate_vma() to do the migration. If the total range to be migrated exceeds SG_MAX_SINGLE_ALLOC the pages will be migrated in chunks of size SG_MAX_SINGLE_ALLOC. However a typo in updating the starting address means that only the first chunk will get migrated. Fix the calculation so that the entire range will get migrated if possible. Signed-off-by:
Alistair Popple <apopple@nvidia.com> Fixes: e3d8b089 ("drm/nouveau/svm: map pages after migration") Reviewed-by:
Ralph Campbell <rcampbell@nvidia.com> Reviewed-by:
-
- 26 Jul, 2022 1 commit
-
-
Nathan Chancellor authored
When booting a kernel compiled with clang's CFI protection (CONFIG_CFI_CLANG), there is a CFI failure in drm_simple_kms_crtc_mode_valid() when trying to call simpledrm_simple_display_pipe_mode_valid() through ->mode_valid(): [ 0.322802] CFI failure (target: simpledrm_simple_display_pipe_mode_valid+0x0/0x8): ... [ 0.324928] Call trace: [ 0.324969] __ubsan_handle_cfi_check_fail+0x58/0x60 [ 0.325053] __cfi_check_fail+0x3c/0x44 [ 0.325120] __cfi_slowpath_diag+0x178/0x200 [ 0.325192] drm_simple_kms_crtc_mode_valid+0x58/0x80 [ 0.325279] __drm_helper_update_and_validate+0x31c/0x464 ... The ->mode_valid() member in 'struct drm_simple_display_pipe_funcs' expects a return type of 'enum drm_mode_status', not 'int'. Correct it to fix the CFI failure. Cc: stable@vger.kernel.org Fixes: 11e8f5fd ("drm: Add simpledrm driver") Link: https://github.com/ClangBuiltLinux/linux/issues/1647Reported-by:
Tomasz Paweł Gajc <tpgxyz@gmail.com> Signed-off-by:
Nathan Chancellor <nathan@kernel.org> Signed-off-by:
Thomas Zimmermann <tzimmermann@suse.de> Reviewed-by:
Sami Tolvanen <samitolvanen@google.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220725233629.223223-1-nathan@kernel.org
-
- 20 Jul, 2022 1 commit
-
-
Liang He authored
In dcss_dev_create() and dcss_dev_destroy(), we should call of_node_put() in fail path or before the dcss's destroy as of_graph_get_port_by_id() has increased the refcount. Fixes: 9021c317 ("drm/imx: Add initial support for DCSS on iMX8MQ") Signed-off-by:
Liang He <windhl@126.com> Reviewed-by:
-
- 19 Jul, 2022 1 commit
-
-
Nícolas F. R. A. Prado authored
The value read from the "hpd-absent-delay-ms" property in DT was being saved to the wrong variable, overriding the hpd_reliable delay. Fix the typo. Fixes: 5540cf8f ("drm/panel-edp: Implement generic "edp-panel"s probed by EDID") Signed-off-by:
Nícolas F. R. A. Prado <nfraprado@collabora.com> Reviewed-by:
André Almeida <andrealmeid@igalia.com> Reviewed-by:
Douglas Anderson <dianders@chromium.org> Signed-off-by:
-
- 18 Jul, 2022 1 commit
-
-
Christian König authored
I've stumbled over this while reviewing patches for DMA-buf and it looks like we completely messed the locking up here. In general most TTM function should only be called while holding the appropriate BO resv lock. Without this we could break the internal buffer object state here. Only compile tested! Signed-off-by:
Christian König <christian.koenig@amd.com> Fixes: 43676605 ("drm/ttm: Add vmap/vunmap to TTM and TTM GEM helpers") Cc: stable@vger.kernel.org Reviewed-by:
Dmitry Osipenko <dmitry.osipenko@collabora.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220715111533.467012-1-christian.koenig@amd.com
-
- 15 Jul, 2022 1 commit
-
-
Dmitry Osipenko authored
Interrupt context can't sleep. Drivers like Panfrost and MSM are taking mutex when job is released, and thus, that code can sleep. This results into "BUG: scheduling while atomic" if locks are contented while job is freed. There is no good reason for releasing scheduler's jobs in IRQ context, hence use normal context to fix the trouble. Cc: stable@vger.kernel.org Fixes: 542cff78 ("drm/sched: Avoid lockdep spalt on killing a processes") Signed-off-by:
Andrey Grodzovsky <andrey.grodzovsky@amd.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220411221536.283312-1-dmitry.osipenko@collabora.com
-
- 08 Jul, 2022 1 commit
-
-
Arunpravin Paneer Selvam authored
This reverts commit c9cad937. This is part of a revert of the following commits: commit 708d19d9 ("drm/amdgpu: move internal vram_mgr function into the C file") commit 5e3f1e77 ("drm/amdgpu: fix start calculation in amdgpu_vram_mgr_new") commit c9cad937 ("drm/amdgpu: add drm buddy support to amdgpu") [WHY] Few users reported garbaged graphics as soon as x starts, reverting until this can be resolved. Signed-off-by:
Arunpravin Paneer Selvam <Arunpravin.PaneerSelvam@amd.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220708093047.492662-3-Arunpravin.PaneerSelvam@amd.comReviewed-by:
-
- 07 Jul, 2022 2 commits
-
-
Ezequiel Garcia authored
Fix small typo which causes the mask for the 'precharge1' setting to be used with the 'precharge2' value. Signed-off-by:
Ezequiel Garcia <ezequiel@vanguardiasur.com.ar> Acked-by:
Javier Martinez Canillas <javierm@redhat.com> Signed-off-by:
-
xinhui pan authored
Need get the new fence when we replace the old one. Fixes: 047a1b87 ("dma-buf & drm/amdgpu: remove dma_resv workaround") Signed-off-by:
xinhui pan <xinhui.pan@amd.com> Reviewed-by:
-
- 04 Jul, 2022 7 commits
-
-
Dmitry Osipenko authored
Calling madvise IOCTL twice on BO causes memory shrinker list corruption and crashes kernel because BO is already on the list and it's added to the list again, while BO should be removed from the list before it's re-added. Fix it. Cc: stable@vger.kernel.org Fixes: 013b6510 ("drm/panfrost: Add madvise and shrinker support") Acked-by:
Alyssa Rosenzweig <alyssa.rosenzweig@collabora.com> Reviewed-by:
Steven Price <steven.price@arm.com> Signed-off-by:
-
Dmitry Osipenko authored
When panfrost_mmu_map_fault_addr() fails, the BO's mapping should be unreferenced and not the shmem object which backs the mapping. Cc: stable@vger.kernel.org Fixes: bdefca2d ("drm/panfrost: Add the panfrost_gem_mapping concept") Reviewed-by:
-
Steven Price authored
Since commit 1ea2a07a ("iommu: Add DMA ownership management interfaces") the Rockchip display driver on the Firefly RK3288 fails to initialise properly. This is because ARM DMA domain is still attached. Let's follow the lead of exynos and tegra and add code to explicitly remove the ARM domain before attaching a new one. Fixes: 1ea2a07a ("iommu: Add DMA ownership management interfaces") Suggested-by:
Robin Murphy <robin.murphy@arm.com> Signed-off-by:
Heiko Stuebner <heiko@sntech.de> Link: https://patchwork.freedesktop.org/patch/msgid/20220615154830.555422-1-steven.price@arm.com
-
Liu Ying authored
It's unnecessary to invert input data enable signal polarity according to the output one. Let's drop the inversion. Since ->atomic_check() does nothing more than the inversion, it can be dropped entirely as well. Without this patch, 'koe,tx26d202vm0bwa' LVDS panel connected with i.MX8MP EVK board does not show any data on screen. Fixes: 463db5c2 ("drm: bridge: ldb: Implement simple Freescale i.MX8MP LDB bridge") Cc: Andrzej Hajda <andrzej.hajda@intel.com> Cc: Neil Armstrong <narmstrong@baylibre.com> Cc: Robert Foss <robert.foss@linaro.org> Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com> Cc: Jonas Karlman <jonas@kwiboo.se> Cc: Jernej Skrabec <jernej.skrabec@gmail.com> Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Marek Vasut <marex@denx.de> Cc: NXP Linux Team <linux-imx@nxp.com> Signed-off-by:
Liu Ying <victor.liu@nxp.com> Reviewed-by:
Marek Vasut <marex@denx.de> Signed-off-by:
Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220701065634.4027537-4-victor.liu@nxp.com
-
Liu Ying authored
When LVDS dual link is used, we have to enable the LDB_CTRL_SPLIT_MODE bit. Fixes: 463db5c2 ("drm: bridge: ldb: Implement simple Freescale i.MX8MP LDB bridge") Cc: Andrzej Hajda <andrzej.hajda@intel.com> Cc: Neil Armstrong <narmstrong@baylibre.com> Cc: Robert Foss <robert.foss@linaro.org> Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com> Cc: Jonas Karlman <jonas@kwiboo.se> Cc: Jernej Skrabec <jernej.skrabec@gmail.com> Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Marek Vasut <marex@denx.de> Cc: NXP Linux Team <linux-imx@nxp.com> Signed-off-by:
-
Liu Ying authored
With LVDS dual link, up to 160MHz mode clock rate is supported. With LVDS single link, up to 80MHz mode clock rate is supported. Fix mode clock rate validation by swapping the maximum mode clock rates of the two link modes. Fixes: 463db5c2 ("drm: bridge: ldb: Implement simple Freescale i.MX8MP LDB bridge") Cc: Andrzej Hajda <andrzej.hajda@intel.com> Cc: Neil Armstrong <narmstrong@baylibre.com> Cc: Robert Foss <robert.foss@linaro.org> Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com> Cc: Jonas Karlman <jonas@kwiboo.se> Cc: Jernej Skrabec <jernej.skrabec@gmail.com> Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Marek Vasut <marex@denx.de> Cc: NXP Linux Team <linux-imx@nxp.com> Signed-off-by:
-
Thomas Zimmermann authored
Always run fbdev removal first to remove simpledrm via sysfb_disable(). This clears the internal state. The later call to drm_aperture_detach_drivers() then does nothing. Otherwise, with drm_aperture_detach_drivers() running first, the call to sysfb_disable() uses inconsistent state. Example backtrace show below: [ 11.663422] ================================================================== [ 11.663426] BUG: KASAN: use-after-free in device_del+0x79/0x5f0 [ 11.663435] Read of size 8 at addr ffff888108185050 by task systemd-udevd/311 [ 11.663440] CPU: 0 PID: 311 Comm: systemd-udevd Tainted: G E 5 .19.0-rc2-1-default+ #1689 [ 11.663445] Hardware name: HP ProLiant DL120 G7, BIOS J01 04/21/2011 [ 11.663447] Call Trace: [ 11.663449] <TASK> [ 11.663451] ? device_del+0x79/0x5f0 [ 11.663456] dump_stack_lvl+0x5b/0x73 [ 11.663462] print_address_description.constprop.0+0x1f/0x1b0 [ 11.663468] ? device_del+0x79/0x5f0 [ 11.663471] ? device_del+0x79/0x5f0 [ 11.663475] print_report.cold+0x3c/0x21c [ 11.663481] ? lock_acquired+0x87/0x1e0 [ 11.663484] ? lock_acquired+0x87/0x1e0 [ 11.663489] ? device_del+0x79/0x5f0 [ 11.663492] kasan_report+0xbf/0xf0 [ 11.663498] ? device_del+0x79/0x5f0 [ 11.663503] device_del+0x79/0x5f0 [ 11.663509] ? device_remove_attrs+0x170/0x170 [ 11.663514] ? lock_is_held_type+0xe8/0x140 [ 11.663523] platform_device_del.part.0+0x19/0xe0 [ 11.663530] platform_device_unregister+0x1c/0x30 [ 11.663535] sysfb_disable+0x2d/0x70 [ 11.663540] remove_conflicting_framebuffers+0x1c/0xf0 [ 11.663546] remove_conflicting_pci_framebuffers+0x130/0x1a0 [ 11.663554] drm_aperture_remove_conflicting_pci_framebuffers+0x86/0xb0 [ 11.663561] ? mgag200_pci_remove+0x30/0x30 [mgag200] [ 11.663578] mgag200_pci_probe+0x2d/0x140 [mgag200] Reported-by:
Zack Rusin <zackr@vmware.com> Signed-off-by:
-
- 01 Jul, 2022 1 commit
-
-
Hans de Goede authored
The Lenovo Yoga Tablet 2 830F / 830L use a panel which has been mounted 90 degrees rotated. Add a quirk for this. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Reviewed-by:
-
- 29 Jun, 2022 3 commits
-
-
Javier Martinez Canillas authored
The platform devices registered by sysfb match with firmware-based DRM or fbdev drivers, that are used to have early graphics using a framebuffer provided by the system firmware. DRM or fbdev drivers later are probed and remove conflicting framebuffers, leading to these platform devices for generic drivers to be unregistered. But the current solution has a race, since the sysfb_init() function could be called after a DRM or fbdev driver is probed and request to unregister the devices for drivers with conflicting framebuffes. To prevent this, disable any future sysfb platform device registration by calling sysfb_disable(), if a driver requests to remove the conflicting framebuffers. Suggested-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:
-
Javier Martinez Canillas authored
This can be used by subsystems to unregister a platform device registered by sysfb and also to disable future platform device registration in sysfb. Suggested-by:
-
Javier Martinez Canillas authored
This function just returned 0 on success or an errno code on error, but it could be useful for sysfb_init() callers to have a pointer to the device. Signed-off-by:
-
- 27 Jun, 2022 1 commit
-
-
Maxime Ripard authored
Commit 30f8c74c ("drm/vc4: Warn if some v3d code is run on BCM2711") introduced a check in vc4_perfmon_get() that dereferences a pointer before we checked whether that pointer is valid or not. Let's rework that function a bit to do things in the proper order. Reported-by:
kernel test robot <lkp@intel.com> Reported-by:
Dan Carpenter <dan.carpenter@oracle.com> Fixes: 30f8c74c ("drm/vc4: Warn if some v3d code is run on BCM2711") Signed-off-by:
Maxime Ripard <maxime@cerno.tech> Reviewed-by:
José Expósito <jose.exposito89@gmail.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220622080243.22119-1-maxime@cerno.tech
-
- 22 Jun, 2022 4 commits
-
-
Saud Farooqui authored
Added return statement in sun4i_layer_format_mod_supported() in case frontend is not present. Signed-off-by:
Saud Farooqui <farooqui_saud@hotmail.com> Signed-off-by:
-
Dan Carpenter authored
The vc4_check_tex_size() function is supposed to return false on error but this error path accidentally returns -ENODEV (which means true). Fixes: 30f8c74c ("drm/vc4: Warn if some v3d code is run on BCM2711") Signed-off-by:
-
Jernej Skrabec authored
Kernel occasionally complains that there is mismatch in segment size when trying to render HW decoded videos and rendering them directly with sun4i DRM driver. Following message can be observed on H6 SoC: [ 184.298308] ------------[ cut here ]------------ [ 184.298326] DMA-API: sun4i-drm display-engine: mapping sg segment longer than device claims to support [len=6144000] [max=65536] [ 184.298364] WARNING: CPU: 1 PID: 382 at kernel/dma/debug.c:1162 debug_dma_map_sg+0x2b0/0x350 [ 184.322997] CPU: 1 PID: 382 Comm: ffmpeg Not tainted 5.19.0-rc1+ #1331 [ 184.329533] Hardware name: Tanix TX6 (DT) [ 184.333544] pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 184.340512] pc : debug_dma_map_sg+0x2b0/0x350 [ 184.344882] lr : debug_dma_map_sg+0x2b0/0x350 [ 184.349250] sp : ffff800009f33a50 [ 184.352567] x29: ffff800009f33a50 x28: 0000000000010000 x27: ffff000001b86c00 [ 184.359725] x26: ffffffffffffffff x25: ffff000005d8cc80 x24: 0000000000000000 [ 184.366879] x23: ffff80000939ab18 x22: 0000000000000001 x21: 0000000000000001 [ 184.374031] x20: 0000000000000000 x19: ffff0000018a7410 x18: ffffffffffffffff [ 184.381186] x17: 0000000000000000 x16: 0000000000000000 x15: ffffffffffffffff [ 184.388338] x14: 0000000000000001 x13: ffff800009534e86 x12: 6f70707573206f74 [ 184.395493] x11: 20736d69616c6320 x10: 000000000000000a x9 : 0000000000010000 [ 184.402647] x8 : ffff8000093b6d40 x7 : ffff800009f33850 x6 : 000000000000000c [ 184.409800] x5 : ffff0000bf997940 x4 : 0000000000000000 x3 : 0000000000000027 [ 184.416953] x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffff000003960e80 [ 184.424106] Call trace: [ 184.426556] debug_dma_map_sg+0x2b0/0x350 [ 184.430580] __dma_map_sg_attrs+0xa0/0x110 [ 184.434687] dma_map_sgtable+0x28/0x4c [ 184.438447] vb2_dc_dmabuf_ops_map+0x60/0xcc [ 184.442729] __map_dma_buf+0x2c/0xd4 [ 184.446321] dma_buf_map_attachment+0xa0/0x130 [ 184.450777] drm_gem_prime_import_dev+0x7c/0x18c [ 184.455410] drm_gem_prime_fd_to_handle+0x1b8/0x214 [ 184.460300] drm_prime_fd_to_handle_ioctl+0x2c/0x40 [ 184.465190] drm_ioctl_kernel+0xc4/0x174 [ 184.469123] drm_ioctl+0x204/0x420 [ 184.472534] __arm64_sys_ioctl+0xac/0xf0 [ 184.476474] invoke_syscall+0x48/0x114 [ 184.480240] el0_svc_common.constprop.0+0x44/0xec [ 184.484956] do_el0_svc+0x2c/0xc0 [ 184.488283] el0_svc+0x2c/0x84 [ 184.491354] el0t_64_sync_handler+0x11c/0x150 [ 184.495723] el0t_64_sync+0x18c/0x190 [ 184.499397] ---[ end trace 0000000000000000 ]--- Fix that by setting DMA mask and segment size. Signed-off-by:
Jernej Skrabec <jernej.skrabec@gmail.com> Reviewed-by:
Samuel Holland <samuel@sholland.org> Signed-off-by:
-
Saud Farooqui authored
Multiplying ints and saving it in unsigned long long could lead to integer overflow before being type casted to unsigned long long. Addresses-Coverity: 1505113: Unintentional integer overflow. Signed-off-by:
-
- 19 Jun, 2022 1 commit
-
-
Maya Matuszczyk authored
The device is identified by "NEXT" in board name, however there are different versions of it, "Next Advance" and "Next Pro", that have different DMI board names. Due to a production error a batch or two have their board names prefixed by "AYANEO", this makes it 6 different DMI board names. To save some space in final kernel image DMI_MATCH is used instead of DMI_EXACT_MATCH. Signed-off-by:
Maya Matuszczyk <maccraft123mc@gmail.com> Reviewed-by:
-
- 16 Jun, 2022 11 commits
-
-
Maxime Ripard authored
The BCM2711 has a separate driver for the v3d, and thus we can't call into any of the driver entrypoints that rely on the v3d being there. Let's add a bunch of checks and complain loudly if that ever happen. Reviewed-by:
Melissa Wen <mwen@igalia.com> Signed-off-by:
-
Maxime Ripard authored
When doing an asynchronous page flip (PAGE_FLIP ioctl with the DRM_MODE_PAGE_FLIP_ASYNC flag set), the current code waits for the possible GPU buffer being rendered through a call to vc4_queue_seqno_cb(). On the BCM2835-37, the GPU driver is part of the vc4 driver and that function is defined in vc4_gem.c to wait for the buffer to be rendered, and once it's done, call a callback. However, on the BCM2711 used on the RaspberryPi4, the GPU driver is separate (v3d) and that function won't do anything. This was working because we were going into a path, due to uninitialized variables, that was always scheduling the callback. However, we were never actually waiting for the buffer to be rendered which was resulting in frames being displayed out of order. The generic API to signal those kind of completion in the kernel are the DMA fences, and fortunately the v3d drivers supports them and signal when its job is done. That API also provides an equivalent function that allows to have a callback being executed when the fence is signalled as done. Let's change our driver a bit to rely on the previous function for the older SoCs, and on DMA fences for the BCM2711. Signed-off-by:
-
Maxime Ripard authored
The BCM2711 doesn't have a v3d GPU so we don't want to call into its BO management code. Let's create an asynchronous page-flip handler for the BCM2711 that just calls into the common code. Reviewed-by:
-
Maxime Ripard authored
The function vc4_async_page_flip() handles asynchronous page-flips in the vc4 driver. However, it mixes some generic code with code that should only be run on older generations that have the GPU handled by the vc4 driver. Let's split the generic part out of vc4_async_page_flip() and into a common function that we be reusable by an handler made for the BCM2711. Reviewed-by:
-
Maxime Ripard authored
We'll soon introduce another completion callback source that won't need to use the BO reference counting, so let's move it around to create a function we will be able to share between both callbacks. Reviewed-by:
-
Maxime Ripard authored
We'll need to extend the vc4_async_flip_state structure to rely on another callback implementation, so let's move the current one into a union. Reviewed-by:
-
Maxime Ripard authored
On the BCM2711, we currently call the vc4_bo_cache_init() and vc4_gem_init() functions. These functions initialize the BO and GEM backends. However, this code was initially created to accomodate the requirements of the GPU on the older SoCs, while the BCM2711 has a separate driver for it. So let's just skip these calls when we're on a newer hardware. Reviewed-by:
-
Maxime Ripard authored
On the BCM2711, our current definition of drm_plane_helper_funcs uses the custom vc4_prepare_fb() and vc4_cleanup_fb(). Those functions rely on the buffer allocation path that was relying on the GPU, and is no longer relevant. Let's create another drm_plane_helper_funcs structure that we will register on the BCM2711. Reviewed-by:
-
Maxime Ripard authored
On the BCM2711, our current definition of drm_mode_config_funcs uses the custom vc4_fb_create(). However, that function relies on the buffer allocation path that was relying on the GPU, and is no longer relevant. Let's create another drm_mode_config_funcs structure that we will register on the BCM2711. Reviewed-by:
-
Maxime Ripard authored
Prior to the BCM2711/RaspberryPi4, the GPU was a part of the display components of the SoC. It was thus a part of the vc4 driver. However, with the BCM2711, it got split out and thus the v3d driver was created. The vc4 driver now only handles the display part. We didn't properly split out the code when doing the BCM2711 support though, and most of the code around buffer allocations is still involved, even though it doesn't have the backing hardware anymore. Let's start the split out by creating a new drm_driver that only reports and uses what we support on the BCM2711. The ioctl were properly filtered already, but we were still exposing a .gem_create_object hook, as well as having an .open and .postclose hooks which are only relevant on older generations. Reviewed-by:
-
Maxime Ripard authored
The vc4_bo_dumb_create() both fixes up the allocation arguments to match the hardware constraints and actually performs the allocation. Since we're going to introduce a new function that uses a different allocator, let's split the arguments fixup to a separate function we will be able to reuse. Reviewed-by:
-
