Add regulator-names for more meaningful description.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

We do not touch LDO2 and LDO4 in linux as they are bypassed.
So remove them completely from device tree.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Do not set reserved bits 0 and 3 in pad configuration.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Rearrange properties in order:
- compatible
- reg
- other generic properties
- device specific properties
- vendor specific properties
- status

And use alphabetical order inside a group.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

In some occasions the ethernet phy IRQ can not be detected correctly
by the SoC. This leads to a non detected link in Linux. The problem is
caused by the buffer that adjusts the voltage between ethernet phy
and SoC. To workaround this, remove the IRQ support for the ethernet
phy and use polling instead.
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This adds support for TQMa93xx module and MBa93xxLA SBC board.
TQMa93xx is a SOM using i.MX93 SOC. The SOM features PMIC, RAM, e-MMC and
some optional peripherals like SPI-NOR, RTC, EEPROM, gyroscope and
secure element.
TQMa93xxLA is a solder on type SOM and can be used directly on MBa93XXLA.
TQMa93xxCA is a feature compatible, socketable type SOM.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add support for the OV5640 camera.

Tested with the following commands:

media-ctl -l "'ov5640 2-003c':0 -> 'csis-32e30000.mipi-csi':0 [1]"
media-ctl -V "'ov5640 2-003c':0 [fmt:UYVY8_1X16/640x480 field:none]"
media-ctl -V "'crossbar':0 [fmt:UYVY8_1X16/640x480 field:none]"
media-ctl -V "'mxc_isi.0':0 [fmt:UYVY8_1X16/640x480 field:none]"
v4l2-ctl --device /dev/video0 --set-fmt-video=width=640,height=480,pixelformat=YUYV
v4l2-ctl --stream-mmap -d /dev/video0;
gst-launch-1.0 -v v4l2src device=/dev/video0 ! video/x-raw,width=640,height=480 ! waylandsink
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

imx8mn-evk has a MIPI DSI port that can be used with a ADV7535 MIPI
DSI to HDMI bridge.

Add support for it.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add support for the OV5640 camera.

Tested with the following commands:

media-ctl -l "'ov5640 2-003c':0 -> 'csis-32e30000.mipi-csi':0 [1]"
media-ctl -V "'ov5640 2-003c':0 [fmt:UYVY8_1X16/640x480 field:none]"
media-ctl -V "'csis-32e30000.mipi-csi':0 [fmt:UYVY8_1X16/640x480 field:none]"
media-ctl -V "'csi':0 [fmt:UYVY8_1X16/640x480 field:none]";
v4l2-ctl --stream-mmap -d /dev/video0
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The A72 nodes have been deleted in this DTB. Removes the corresponding
thermal zone to ensure a successful build.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add thermal zone and cooling map for cpufreq.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add A53 and A72 opp_table.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Dtschema of the leds sub-node names expects "led-1" instead of led1.
So, the sub-node names are corrected according to the regexes.
Signed-off-by: Yashwanth Varakala <y.varakala@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add support for the following Raspberry Pi displays:
 - DFROBOT DRF0678 7in 800x480 TFT DSI capacitive touch
 - DFROBOT DRF0550 5in 800x480 TFT DSI capacitive touch

Both have the following hardware:
 - FocalTech FT5406 10pt touch controller (with no interrupt)
 - Powertip PH800480T013-IDF02 compatible panel
 - Toshiba TC358762 compatible DSI to DBI bridge
 - ATTINY based regulator used for backlight controller and panel enable

Support is added via a device-tree overlay. The touch controller is not
yet supported as polling mode is needed.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add support for the following Raspberry Pi displays:
 - DFROBOT DRF0678 7in 800x480 TFT DSI capacitive touch
 - DFROBOT DRF0550 5in 800x480 TFT DSI capacitive touch

Both have the following hardware:
 - FocalTech FT5406 10pt touch controller (with no interrupt)
 - Powertip PH800480T013-IDF02 compatible panel
 - Toshiba TC358762 compatible DSI to DBI bridge
 - ATTINY based regulator used for backlight controller and panel enable

Support is added via a device-tree overlay. The touch controller is not
yet supported as polling mode is needed.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The reg size of etm nodes is incorrectly set to 64k instead of 4k. This
leads to a crash when calling amba_read_periphid().  After corrected reg
size, amba_read_periphid() retrieve the correct periphid.
arm,primecell-periphid were removed from the etm nodes.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add missing whitespace between node name/label and opening {.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Two entries are expected for PCIe ranges.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The DTS code coding style expects exactly one space before and after '='
sign.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

i.MX93 and i.MX8ULP lpuart add some new featurs based on i.MX7ULP, for
example, i.MX93 and i.MX8ULP can support EOP(end-of-packet) function
while i.MX7ULP doesn't support, so add "fsl,imx8ulp-lpuart" compatible
string for i.MX93 to support those new features.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Drop the i.MX8DXL backwards compatibility with i.MX7ULP since they
differ from clocks handling point of view.

dtbs_check has the following warnings:
linux-next/arch/arm64/boot/dts/freescale/imx8dxl-evk.dtb: serial@5a060000: compatible: 'oneOf' conditional failed, one must be fixed:
        ['fsl,imx8qxp-lpuart', 'fsl,imx7ulp-lpuart'] is too long
        'fsl,imx93-lpuart' was expected
        'fsl,imx8qxp-lpuart' is not one of ['fsl,imx8qm-lpuart', 'fsl,imx8dxl-lpuart']
        'fsl,imxrt1050-lpuart' was expected
        'fsl,imx8ulp-lpuart' was expected
        'fsl,imx8qxp-lpuart' was expected
        'fsl,imxrt1170-lpuart' was expected
        From schema: linux-next/Documentation/devicetree/bindings/serial/fsl-lpuart.yaml
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add reserved memory node for rpmsg
Enable CM33 node with mailbox property included for doorbell.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add CM33 node for i.MX93
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add CMA region for DMA usage.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add tmu node and thermal-zones
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

scl-gpios and sda-gpios need GPIO_OPEN_DRAIN flag, otherwise the
following run-time warning is seen:

gpio-144 (scl): enforced open drain please flag it properly in DT/ACPI DSDT/board file
gpio-146 (scl): enforced open drain please flag it properly in DT/ACPI DSDT/board file
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Now that it is finally possible to get the MAC addresses from the OTP
memory, use it to set the addresses of the network devices.

There are 8 reserved MAC addresses in total per board. Distribute them
as follows:

+----------+------+------+------+------+------+
|          | var1 | var2 | var3 | var4 | kbox |
+----------+------+------+------+------+------+
| enetc #0 |   +0 |      |      |   +0 |   +0 |
| enetc #1 |      |      |   +0 |   +1 |   +1 |
| enetc #2 |      |   +2 |      |      |   +2 |
| enetc #3 |      |   +3 |      |      |   +3 |
| felix p0 |      |   +0 |      |      |   +4 |
| felix p1 |      |   +1 |      |      |   +5 |
| felix p2 |      |      |      |      |   +6 |
| felix p3 |      |      |      |      |   +7 |
| felix p4 |      |      |      |      |      |
| felix p5 |      |      |      |      |      |
+----------+------+------+------+------+------+

An empty cell means, the port is not available and thus doesn't need an
ethernet address.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add i2c4 sda-/scl-gpios with the corresponding pinmux entries.
Signed-off-by: Cem Tenruh <c.tenruh@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Set Pull Resistors Enable bit to put signal into a defined state.
Signed-off-by: Yannic Moog <y.moog@phytec.de>
Signed-off-by: Cem Tenruh <c.tenruh@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add #address-cells and #size-cells properties to som_flash. This
enables correct parsing of added SPI NOR mtd partition child nodes that
are set in the bootloader.
Signed-off-by: Yannic Moog <y.moog@phytec.de>
Signed-off-by: Cem Tenruh <c.tenruh@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add TPM node for phyBOARD-Polis i.MX 8M Mini which has the Infineon-SLB
9670 TPM2.0 module populated.
Signed-off-by: Yashwanth Varakala <y.varakala@phytec.de>
Signed-off-by: Yannic Moog <y.moog@phytec.de>
Signed-off-by: Cem Tenruh <c.tenruh@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The Beacon Embedded imx8mm development kit has a DSI
to HDMI bridge chip.  The bridge supports stereo audio
and hot-plugging.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The DSI to HDMI bridge uses the address currently assigned to
the camera, so change the camera address to the alternative
address of 0x10 in preparation to enable the bridge.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The Beacon Embedded imx8mn development kit has a DSI
to HDMI bridge chip.  The bridge supports stereo audio
and hot-plug detection.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Fix typo in imx8mm-venice-gw72xx-0x-imx219 overlay causing it to use
gw73xx configuration.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Update the imx8mp-venice-gw74xx for revB:
 - add CAN1
 - add TIS-TPM on SPI2
 - add FAN controller
 - fix PMIC I2C bus (revA PMIC I2C was non-functional so no need for
   backward compatible option)
 - M2 socket GPIO's moved
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

On the GW7904 uart1 can use UART3_TX/RX for hardware flow control
which was the desired default configuration. Remove uart3 and configure
uart1 for hardware flow control.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The GW7902 has a Murata LBEE5H 802.11abgnac / BT5 module based on the
Cypress CYW43455 which supports SDR50/SDR104.

Add dt pinctrl for the 100mhz and 200mhz states to support SDR50/SDR104.

While at it add the dt node for the CYW43455 wifi.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The GW7901 has a Murata LBEE5H 802.11abgnac / BT5 module based on the
Cypress CYW43455 which supports SDR50/SDR104.

Add dt pinctrl for the 100mhz and 200mhz states to support SDR50/SDR104.

While at it add the dt node for the CYW43455 wifi for the brcmfmac
driver.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add regulator config for cpu-supply in order to support cpufreq.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>