With clkdev based clock lookup support, the clock set and get operation
using clock names communicated between the samsung uart driver and the
SoC specific extension can be removed.

In addition to that, for each platform specific extension, add the
default clock selection, number of clock options for uart baud generator,
clock selection bit mask and shift values which is required by the
clkdev support in samsung uart driver.

The default clock selection value 'def_clk_sel' specifies the default clock
to be used as the source clock for baud rate generator in case the platform
code does not specify the same.

Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

With clkdev based clock lookup added to samsung serial driver, the use
of 'struct s3c24xx_uart_clksrc' to supply clock names in platform
data is removed from all the Samsung platform code.

Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Ramax Lo <ramaxlo@gmail.com>
Cc: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Instead of using clock names supplied in platform data, use a generic
clock name 'clk_uart_baud' to look up clocks. The platform code should
register clocks with the name 'clk_uart_baud' which can be used by the
baud rate generator. The clock lookup and selection of the best clock
as baud rate clock is reworked.

Platform code can specify the clocks that can be used as source for the
baud clock (as supported previously by passing names of clocks). A new
member is added to the platform data 'clk_sel' which holds a bit-field
value with each bit representing a baud source clock. If a bit at any
bit position is set, that clock is looked up to participate in the
selection of the baud clock source.

Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

s3c2440 uses fclk/n (fclk divided by n) clock as one of the possible clocks used
to generate the baud rate clock. The divider 'n' in this case can be logically
represented outside of the uart controller.

This patch creates a new clock by name "fclk_n" for s3c2440 based platforms to
represent the fclk/n clock in the platform code. This clock provides a get_rate
callback that checks the UCON0/1/2 registers to determine the clock rate. The
samsung uart driver would receive the "fclk_n" clock name as one of the possible
baud rate clock options and the driver need not determine clock rate of fclk/n.

Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Add a pointer to the location of the platform data in the driver's private
data. When instantiated using device tree, pdev->dev->platform_data does not
necessarily point to a valid instance of platform data. The platform data
pointer in the driver's private data could be set to pdev->dev->platform_data
or platform data instance created from device tree.

Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

As gpio chips get registered, a device tree node which represents the
gpio chip is searched and attached to it. A translate function is also
provided to convert the gpio specifier into actual platform settings
for pin function selection, pull up/down and driver strength settings.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
[kgene.kim@samsung.com: fixed build error]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Enable conversion of device tree interrupt specifier to linux
virq domain for GIC controller.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

The timer irqs statically mapped from linux irq numbers 11 to 15 are
moved to the end of the statically mapped linux irq space. The GIC PPI
and SPI interrupts are relocated to start from 16 and 32 of the linux
irq space. This is a required to add device tree support for GIC and
Interrupt combiner for EXYNOS4.

A new macro 'IRQ_TIMER_BASE' specifies a platform specific base of the
linux virq number for the timer interrupts. For exynos4, this base is
set to end of the linux virq space.  For the other S5P platforms, the
existing base '11' is retained.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

This reverts commit eb1711bb.

It blows up the i915 seqno tracking, resulting in the

	BUG_ON(seqno == 0);

in i915_wait_request() triggering, which will cause lock-ups.

See for example
  https://bugs.launchpad.net/ubuntu/+source/linux/+bug/903010
  https://lkml.org/lkml/2011/12/14/395Reported-requested-and-tested-by: Dirk Hohndel <dirk@hohndel.org>
Reported-by: Richard Eames <Richard.Eames@flinders.edu.au>
Reported-by: Rocko Requin <rockorequin@hotmail.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Keith Packard <keithp@keithp.com>
Cc: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc32: Be less strict in matching %lo part of relocation.
  sbus: convert drivers/sbus/char/* to use module_platform_driver()
  bbc_i2c: Remove unneeded err variable
  sparc: Use kmemdup rather than duplicating its implementation

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  ipv6: Check dest prefix length on original route not copied one in rt6_alloc_cow().
  sch_gred: should not use GFP_KERNEL while holding a spinlock
  ipip, sit: copy parms.name after register_netdevice
  ipv6: Fix for adding multicast route for loopback device automatically.
  ssb: fix init regression with SoCs
  rtl8192{ce,cu,de,se}: avoid problems because of possible ERFOFF -> ERFSLEEP transition
  mac80211: fix another race in aggregation start
  fsl_pq_mdio: Clean up tbi address configuration
  ppp: fix pptp double release_sock in pptp_bind()
  net/fec: fix the use of pdev->id
  ath9k: fix check for antenna diversity support
  batman-adv: delete global entry in case of roaming
  batman-adv: in case of roaming mark the client with TT_CLIENT_ROAM
  Bluetooth: Correct version check in hci_setup
  btusb: fix a memory leak in btusb_send_frame()
  Bluetooth: bnep: Fix module reference
  Bluetooth: cmtp: Fix module reference
  Bluetooth: btmrvl: support Marvell Bluetooth device SD8797

Merge branches 'for-linus' and 'for-linus-3.2' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: unplug every once and a while
  Btrfs: deal with NULL srv_rsv in the delalloc inode reservation code
  Btrfs: only set cache_generation if we setup the block group
  Btrfs: don't panic if orphan item already exists
  Btrfs: fix leaked space in truncate
  Btrfs: fix how we do delalloc reservations and how we free reservations on error
  Btrfs: deal with enospc from dirtying inodes properly
  Btrfs: fix num_workers_starting bug and other bugs in async thread
  BTRFS: Establish i_ops before calling d_instantiate
  Btrfs: add a cond_resched() into the worker loop
  Btrfs: fix ctime update of on-disk inode
  btrfs: keep orphans for subvolume deletion
  Btrfs: fix inaccurate available space on raid0 profile
  Btrfs: fix wrong disk space information of the files
  Btrfs: fix wrong i_size when truncating a file to a larger size
  Btrfs: fix btrfs_end_bio to deal with write errors to a single mirror

* 'for-linus-3.2' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  btrfs: lower the dirty balance poll interval

* 'drm-intel-fixes' of git://people.freedesktop.org/~keithp/linux:
  drm/i915/dp: Dither down to 6bpc if it makes the mode fit
  drm/i915: enable semaphores on per-device defaults
  drm/i915: don't set unpin_work if vblank_get fails
  drm/i915: By default, enable RC6 on IVB and SNB when reasonable
  iommu: Export intel_iommu_enabled to signal when iommu is in use
  drm/i915/sdvo: Include LVDS panels for the IS_DIGITAL check
  drm/i915: prevent division by zero when asking for chipset power
  drm/i915: add PCH info to i915_capabilities
  drm/i915: set the right SDVO transcoder for CPT
  drm/i915: no-lvds quirk for ASUS AT5NM10T-I
  drm/i915: Treat pre-gen4 backlight duty cycle value consistently
  drm/i915: Hook up Ivybridge eDP
  drm/i915: add multi-threaded forcewake support

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: HDA: Use LPIB Position fix for Intel SCH Poulsbo
  ALSA: hda: fix mute led polarity for HP laptops with buggy BIOS
  ALSA: HDA: Set position fix to LPIB for an Atom/Poulsbo based device
  ASoC: Fix hx4700 error handling to free gpios if snd_soc_register_card fails
  ASoC: WM8958: correctly show firmware magic on mismatch
  ASoC: mxs: Add appropriate MODULE_ALIAS()
  ASoC: mxs: Add missing MODULE_LICENSE("GPL")
  ASoC: Fix WM8996 24.576MHz clock operation
  ASoC: Include linux/module.h for smdk2443_wm9710
  ASoC: Fix a typo in jive_wm8750
  ASoC: Fix build dependency for SND_SOC_JZ4740_CODEC
  ASoC: Include linux/io.h for jz4740 codec

* 'gpio/merge' of git://git.secretlab.ca/git/linux-2.6:
  gpio: Fix DA9052 GPIO build errors.
  gpio: mpc8xxx: don't allow input-only pins to be output for MPC5121
  gpio-ml-ioh: Add the irq_disable/irq_enable hooks for ml-ioh irq chip
  gpio-ml-ioh: fix a bug in the interrupt handler
  gpio: pl061: drop extra check for NULL platform_data

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: OMAP: rx51: fix USB
  ARM: OMAP: mcbsp: Fix possible memory corruption
  arm/imx: fix power button on imx51 babbage board
  ARM: imx: fix cpufreq build errors
  ARM: mx5: add __initconst for fec pdata
  MXC PWM: should active during DOZE/WAIT/DBG mode
  ARM: EXYNOS: Fix build error without CONFIG_LOCAL_TIMERS
  ARM: EXYNOS: Fix for stall in case of cpu hotplug or sleep
  ARM: S5PV210: Set 1000ns as PWM backlight period on SMDKV210
  ARM: SAMSUNG: remove duplicated header include

* 'for-linus' of git://git.kernel.dk/linux-block:
  block: don't kick empty queue in blk_drain_queue()
  block/swim3: Locking fixes
  loop: Fix discard_alignment default setting
  cfq-iosched: fix cfq_cic_link() race confition
  cfq-iosched: free cic_index if blkio_alloc_blkg_stats fails
  cciss: fix flush cache transfer length
  cciss: Add IRQF_SHARED back in for the non-MSI(X) interrupt handler
  loop: fix loop block driver discard and encryption comment
  block: initialize request_queue's numa node during

Tests show that the original large intervals can easily make the dirty
limit exceeded on 100 concurrent dd's. So adapt to as large as the
next check point selected by the dirty throttling algorithm.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>

Some active adaptors (VGA usually) only have two lanes at 2.7GHz.
That's a maximum pixel clock of 144MHz at 8bpc, but 192MHz at 6bpc.

Fixes Asus UX31 panel being black at startup due to no valid modes since
dc22ee6f.

v2: Rebased to current code, resulting in the fix applying to EDP panels as
    well.  Also changed from spatio-temporal to just spatial dithering on
    pre-ironlake, to be conssitent (and less visual flicker)
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Tested-by: Eric Anholt <eric@anholt.net>
Tested-by: Dirk Hohndel <hohndel@infradead.org>
Signed-off-by: Keith Packard <keithp@keithp.com>

This adds a default setting for semaphores parameter, and enables
semaphores by default on IVB.

For now, as semaphores interaction with VTd causes random issues on
SNB, we do not enable them by default. But they can still be enabled
via the semaphores=1 kernel parameter.

v2: enables semaphores on SNB when IO remapping is disabled, with base
on Keith Packard patch.

CC: Daniel Vetter <daniel.vetter@ffwll.ch>
CC: Ben Widawsky <ben@bwidawsk.net>
CC: Keith Packard <keithp@keithp.com>
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
CC: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=42696
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=40564
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=41353
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=38862Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>

This fixes a race where we may try to finish a page flip and decrement
the refcount even if our vblank_get failed and we ended up with a
spurious flip pending interrupt.

Fixes https://bugs.freedesktop.org/show_bug.cgi?id=34211.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>

RC6 should always work on IVB, and should work on SNB whenever IO
remapping is disabled. RC6 never works on Ironlake. Make the default
value for the parameter follow these guidelines. Setting the value
to either 0 or 1 will force the specified behavior.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=38567
Cc: Ted Phelps <phelps@gnusto.com>
Cc: Peter <pab1612@gmail.com>
Cc: Lukas Hejtmanek <xhejtman@fi.muni.cz>
Cc: Andrew Lutomirski <luto@mit.edu>

In i915 driver, we do not enable either rc6 or semaphores on SNB when dmar
is enabled. The new 'intel_iommu_enabled' variable signals when the
iommu code is in operation.

Cc: Ted Phelps <phelps@gnusto.com>
Cc: Peter <pab1612@gmail.com>
Cc: Lukas Hejtmanek <xhejtman@fi.muni.cz>
Cc: Andrew Lutomirski <luto@mit.edu>
CC: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>

We were checking whether the supplied edid matched the connector it was
read from. We do this in case a DDC read returns an EDID for another
device on a multifunction or otherwise interesting card. However, we
failed to include LVDS as a digital device and so rejecting an otherwise
valid EDID.

Fixes the detection of the secondary SDVO LVDS panel on the Libretto
W105.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=39216Signed-off-by: Keith Packard <keithp@keithp.com>

This prevents an in-kernel division by zero which happens when we are
asking for i915_chipset_val too quickly, or within a race condition
between the power monitoring thread and userspace accesses via debugfs.

The issue can be reproduced easily via the following command:
while ``; do cat /sys/kernel/debug/dri/0/i915_emon_status; done

This is particularly dangerous because it can be triggered by
a non-privileged user by just reading the debugfs entry.

This issue was also found independently by Konstantin Belousov
<kostikbel@gmail.com>, who proposed a similar patch.
Reported-by: Konstantin Belousov <kostikbel@gmail.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>

v2: add a CPT-specific macro, make code cleaner
v3: fix commit message

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=41272
Cc: stable@kernel.org
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>

https://bugzilla.redhat.com/show_bug.cgi?id=750006Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Keith Packard <keithp@keithp.com>

Merge branch 'samsung-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes

* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/ibft:
  ibft: Fix finding IBFT ACPI table on UEFI

* 'staging-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: r8712u: Add new USB ID
  staging: tidspbridge: request dmtimer clocks on init
  staging: tidspbridge: include module.h by default

* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  USB: option: Removing one bogus and adding some new Huawei combinations
  USB: cdc-acm: add IDs for Motorola H24 HSPA USB module.
  usb: option: Add Huawei E398 controlling interfaces
  usb: renesas_usbhs: add hcd->has_tt for low/full speed
  usb: renesas_usbhs: typofix: irq_dtch control DTCHE
  usb: gadget: storage: release superspeed descriptors.

The bisection implemented in unwind_find_origin() stopped to early.  If
there is only a single entry left to check the original code just took
the end point as origin which might be wrong.

This was introduced in commit de66a979 ("ARM: 7187/1: fix unwinding
for XIP kernels").
Reported-and-tested-by: Nick Bowler <nbowler@elliptictech.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The btrfs io submission threads can build up massive plug lists.  This
keeps things more reasonable so we don't hand over huge dumps of IO at
once.
Signed-off-by: Chris Mason <chris.mason@oracle.com>

While probing, fd sets up queue, probes hardware and tears down the
queue if probing fails.  In the process, blk_drain_queue() kicks the
queue which failed to finish initialization and fd is unhappy about
that.

  floppy0: no floppy controllers found
  ------------[ cut here ]------------
  WARNING: at drivers/block/floppy.c:2929 do_fd_request+0xbf/0xd0()
  Hardware name: To Be Filled By O.E.M.
  VFS: do_fd_request called on non-open device
  Modules linked in:
  Pid: 1, comm: swapper Not tainted 3.2.0-rc4-00077-g5983fe2b #2
  Call Trace:
   [<ffffffff81039a6a>] warn_slowpath_common+0x7a/0xb0
   [<ffffffff81039b41>] warn_slowpath_fmt+0x41/0x50
   [<ffffffff813d657f>] do_fd_request+0xbf/0xd0
   [<ffffffff81322b95>] blk_drain_queue+0x65/0x80
   [<ffffffff81322c93>] blk_cleanup_queue+0xe3/0x1a0
   [<ffffffff818a809d>] floppy_init+0xdeb/0xe28
   [<ffffffff818a72b2>] ? daring+0x6b/0x6b
   [<ffffffff810002af>] do_one_initcall+0x3f/0x170
   [<ffffffff81884b34>] kernel_init+0x9d/0x11e
   [<ffffffff810317c2>] ? schedule_tail+0x22/0xa0
   [<ffffffff815dbb14>] kernel_thread_helper+0x4/0x10
   [<ffffffff81884a97>] ? start_kernel+0x2be/0x2be
   [<ffffffff815dbb10>] ? gs_change+0xb/0xb

Avoid it by making blk_drain_queue() kick queue iff dispatch queue has
something on it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Ralf Hildebrandt <Ralf.Hildebrandt@charite.de>
Reported-by: Wu Fengguang <fengguang.wu@intel.com>
Tested-by: Sergei Trofimovich <slyich@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Merge branch 'stable/for-linus-fixes-3.2' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen

* 'stable/for-linus-fixes-3.2' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
  xen/swiotlb: Use page alignment for early buffer allocation.
  xen: only limit memory map to maximum reservation for domain 0.

Merge branch 'for-chris' of http://git.kernel.org/pub/scm/linux/kernel/git/josef/btrfs-work into integration

Conflicts:
	fs/btrfs/inode.c
Signed-off-by: Chris Mason <chris.mason@oracle.com>

btrfs_update_inode is sometimes called with a null reservation.
Signed-off-by: Chris Mason <chris.mason@oracle.com>