The USB stack uses error code -ENOSPC to indicate that the periodic
schedule is too full, with insufficient bandwidth to accommodate a new
allocation.  It uses -EFBIG to indicate that an isochronous transfer
could not be linked into the schedule because it would exceed the
number of isochronous packets the host controller driver can handle
(generally because the new transfer would extend too far into the
future).

ehci-hcd uses the wrong error code at one point.  This patch fixes it,
along with a misleading comment and debugging message.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit c3ee9b76 (EHCI: improved logic for isochronous scheduling)
introduced the idea of using ehci->last_iso_frame as the origin (or
base) for the circular calculations involved in modifying the
isochronous schedule.  However, the new code it added used
ehci->last_iso_frame before the value was properly initialized.  This
patch rectifies the mistake by moving the initialization lines earlier
in iso_stream_schedule().

This fixes Bugzilla #72891.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: c3ee9b76Reported-by: Joe Bryant <tenminjoe@yahoo.com>
Tested-by: Joe Bryant <tenminjoe@yahoo.com>
Tested-by: Martin Long <martin@longhome.co.uk>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Solves xhci error cases with debug messages:
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 1.
usb 1-6: hub failed to enable device, error -22

xhci will give a context state error if we try to set a slot in default
state to the same default state with a special address device command.

Turns out this happends in several cases:
- retry reading the device rescriptor in hub_port_init()
- usb_reset_device() is called for a slot in default state
- in resume path, usb_port_resume() calls hub_port_init()

The default state is usually reached from most states with a reset device
command without any context state errors, but using the address device
command with BSA bit set (block set address) only works from the enabled
state and will otherwise cause context error.

solve this by checking if we are already in the default state before issuing
a address device BSA=1 command.

Fixes: 48fc7dbd ("usb: xhci: change enumeration scheme to 'new scheme'")
Cc: <stable@vger.kernel.org> # v3.14+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit 14b4099c

It moved platform_set_drvdata(pdev, ci) before hcd is created,
and the hcd will assign itself as ci controller's drvdata during
the hcd creation function (in usb_create_shared_hcd), so it
overwrites the real ci's drvdata which we want to use.

So, if the controller is at host mode, the system suspend
API will get the wrong struct ci_hdrc pointer, and cause the
oops.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'for-3.19-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-linus

Kishon writes:

misc fixes in PHY drivers

Merge tag 'fixes-for-v3.19-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus

Felipe writes:

usb: fixes for v3.19-rc2

First set of fixes for current -rc cycle. There are
a couple of build break fixes after Tony Lindgren's
recent MUSB patchset, some memory leak fixes also
with MUSB, a use-after-free fix with the UAC1
function. Atmel UDC got a fix for a possible hang
and another for DMA setting, while dwc2 learned to
kill requests in ->udc_stop() which fixes a few leaks
too.

One new device support here, dwc3 now supports Intel's
Sunrise Point.
Signed-off-by: Felipe Balbi <balbi@ti.com>

Prior to DRA74x silicon rev 1.1, pcie_pcs register bits 8-15 and bits 16-23
were used to configure RC delay count for phy1 and phy2 respectively.
phyid was used as index to distinguish the phys and to configure the delay
values appropriately.

As of DRA74x silicon rev 1.1, pcie_pcs register definition has changed.
Bits 16-23 are used to configure delay values for *both* phy1 and phy2.

Hence phyid is no longer required.

So, drop id field from ti_pipe3 structure and its subsequent references
for configuring pcie_pcs register.

Also, pcie_pcs register now needs to be configured with delay value of 0x96
at bit positions 16-23. See register description of CTRL_CORE_PCIE_PCS in
ARM572x TRM, SPRUHZ6, October 2014, section 18.5.2.2, table 18-1804.

This is needed to ensure Gen2 cards are enumerated consistently.

DRA72x silicon behaves same way as DRA74x rev 1.1 as far as this functionality
is considered.

Test results on DRA74x and DRA72x EVMs:

Before patch
------------
DRA74x ES 1.0: Gen1 cards work, Gen2 cards do not work (expected result due to
silicon errata)
DRA74x ES 1.1: Gen1 cards work, Gen2 cards do not work sometimes due to incorrect
programming of register

DRA72x: Gen1 cards work, Gen2 cards do not work sometimes due to incorrect
programming of register

After patch
-----------
DRA74x ES 1.0: Gen1 cards work, Gen2 cards do not work (expected result due to
silicon errata)
DRA74x ES 1.1: Gen1 cards work, Gen2 cards work consistently.

DRA72x: Gen1 and Gen2 cards enumerate consistently.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

The allwinner SDK uses a value of 3 for the disconnect threshold setting on
sun6i, do the same in the kernel.

In my previous experience with sun5i problems getting the threshold right
is important to avoid usb2 devices being unplugged sometimes going unnoticed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

We need to unlock before returning the -EINVAL here.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Pull device mapper fixes from Mike Snitzer:
 "Thre stable fixes and one fix for a regression introduced during 3.19
  merge:

   - Fix inability to discard used space when the thin-pool target is in
     out-of-data-space mode and also transition the thin-pool back to
     write mode once free space is made available.

   - Fix DM core bio-based end_io bug that prevented proper
     post-processing of the error code returned from the block layer.

   - Fix crash in DM thin-pool due to thin device being added to the
     pool's active_thins list before properly initializing the thin
     device's refcount"

* tag 'dm-3.19-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
  dm: fix missed error code if .end_io isn't implemented by target_type
  dm thin: fix crash by initializing thin device's refcount and completion earlier
  dm thin: fix missing out-of-data-space to write mode transition if blocks are released
  dm thin: fix inability to discard blocks when in out-of-data-space mode

This reverts commit c8475d14.

There are several[1][2] of bug reports which points to this commit as potential
cause[3].

Let's revert it until we figure out what's going on.

[1] https://lkml.org/lkml/2014/11/14/342
[2] https://lkml.org/lkml/2014/12/22/213
[3] https://lkml.org/lkml/2014/12/9/741Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Acked-by: Davidlohr Bueso <dave@stgolabs.net>
Cc: Hugh Dickins <hughd@google.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Mel Gorman <mgorman@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

When receive data, the RXRDY in status register set by hardware
after a new packet has been stored in the endpoint FIFO. When it
is copied from FIFO, this bit is cleared which make the FIFO can
be accessed again.

In the receive_data() function, this bit RXRDY has been cleared.
So, after the receive_data() function return, this bit should
not be cleared again, or else it may cause the accessing FIFO
corrupt, which will make the data loss.

Fixes: 914a3f3b (USB: add atmel_usba_udc driver)
Cc: <stable@vger.kernel.org> # 2.6.24+
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

According to the datasheet, when transfer using DMA, the control
setting for IN packet only need END_BUF_EN, END_BUF_IE, CH_EN,
while for OUT packet, need more two bits END_TR_EN and END_TR_IE
to be configured.

Fixes: 914a3f3b (USB: add atmel_usba_udc driver)
Cc: <stable@vger.kernel.org> # 2.6.24+
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Add PCI IDs for Intel Sunrise Point PCH.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Commit 3b74c73f switched over to memdup_user()
in ep_write() function and removed kfree (kbuf).
memdup_user() function allocates memory which is never freed.

Fixes: 3b74c73f (usb: gadget: inode: switch over to memdup_user())
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Mario Schuknecht <mario.schuknecht@dresearch-fe.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>

since the split of host+gadget mode in commit 74c2e936 ("usb: musb:
factor out hcd initalization") we leak the usb_hcd struct. We call now
musb_host_cleanup() which does basically usb_remove_hcd() and also sets
the hcd variable to NULL. Doing so makes the finall call to
musb_host_free() basically a nop and the usb_hcd remains around for ever
without anowner.
This patch drops that NULL assignment for that reason.

Fixes: 74c2e936 ("usb: musb: factor out hcd initalization")
Cc: <stable@vger.kernel.org> # v3.11+
Cc: Daniel Mack <zonque@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This makes us sure that all requests are completed before we unbind
gadget. There are assumptions in gadget API that all requests have to
be completed and leak of complete can break some usb function drivers.

For example unbind of ECM function can cause NULL pointer dereference:

[   26.396595] configfs-gadget gadget: unbind function
'cdc_ethernet'/e79c4c00
[   26.414999] Unable to handle kernel NULL pointer dereference at
virtual address 00000000
(...)
[   26.452223] PC is at ecm_unbind+0x6c/0x9c
[   26.456209] LR is at ecm_unbind+0x68/0x9c
(...)
[   26.603696] [<c033fdb4>] (ecm_unbind) from [<c033661c>]
(purge_configs_funcs+0x94/0xd8)
[   26.611674] [<c033661c>] (purge_configs_funcs) from [<c0336674>]
(configfs_composite_unbind+0x14/0x34)
[   26.620961] [<c0336674>] (configfs_composite_unbind) from
[<c0337124>] (usb_gadget_remove_driver+0x68/0x9c)
[   26.630683] [<c0337124>] (usb_gadget_remove_driver) from [<c03376c8>]
(usb_gadget_unregister_driver+0x64/0x94)
[   26.640664] [<c03376c8>] (usb_gadget_unregister_driver) from
[<c0336be8>] (unregister_gadget+0x20/0x3c)
[   26.650038] [<c0336be8>] (unregister_gadget) from [<c0336c84>]
(gadget_dev_desc_UDC_store+0x80/0xb8)
[   26.659152] [<c0336c84>] (gadget_dev_desc_UDC_store) from
[<c0335120>] (gadget_info_attr_store+0x1c/0x28)
[   26.668703] [<c0335120>] (gadget_info_attr_store) from [<c012135c>]
(configfs_write_file+0xe8/0x148)
[   26.677818] [<c012135c>] (configfs_write_file) from [<c00c8dd4>]
(vfs_write+0xb0/0x1a0)
[   26.685801] [<c00c8dd4>] (vfs_write) from [<c00c91b8>]
(SyS_write+0x44/0x84)
[   26.692834] [<c00c91b8>] (SyS_write) from [<c000e560>]
(ret_fast_syscall+0x0/0x30)
[   26.700381] Code: e30409f8 e34c0069 eb07b88d e59430a8 (e5930000)
[   26.706485] ---[ end trace f62a082b323838a2 ]---

It's because in some cases request is still running on endpoint during
unbind and kill_all_requests() called from s3c_hsotg_udc_stop() function
doesn't cause call of complete() of request. Missing complete() call
causes ecm->notify_req equals NULL in ecm_unbind() function, and this
is reason of this bug.

Similar breaks can be observed in another usb function drivers.

This patch fixes this bug forcing usb request completion in when
s3c_hsotg_ep_disable() is called from s3c_hsotg_udc_stop().
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Replace a misspelled function name by %s and then __func__.

This was done using Coccinelle, including the use of Levenshtein distance,
as proposed by Rasmus Villemoes.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Commit 82c02f58 ("usb: musb: Allow multiple glue layers to be
built in") enabled selecting multiple glue layers, which in turn
exposed things more for randconfig builds. If NOP_USB_XCEIV is
built-in and TUSB6010 is a loadable module, we will get:

drivers/built-in.o: In function `tusb_remove':
tusb6010.c:(.text+0x16a817): undefined reference to `usb_phy_generic_unregister'
drivers/built-in.o: In function `tusb_probe':
tusb6010.c:(.text+0x16b24e): undefined reference to `usb_phy_generic_register'
make: *** [vmlinux] Error 1

Let's fix this the same way as commit 70c1ff4b ("usb: musb:
tusb-dma can't be built-in if tusb is not").

And while at it, let's not allow selecting the glue layers except
on platforms really using them unless COMPILE_TEST is specified:

- TUSB6010 is in practise only used on omaps

- DSPS is only used on TI platforms

- UX500 is only used on STE platforms

Cc: Linus Walleij <linus.walleij@linaro.org>
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

At f_audio_free_inst, it tries to access struct gaudio *card which is
freed at f_audio_free, it causes below oops if the audio device is not
there (do unload module may trigger the same problem). The gaudio_cleanup
is related to function, so it is better move to f_audio_free.

root@freescale ~$ modprobe g_audio
[  751.968931] g_audio gadget: unable to open sound control device file: /dev/snd/controlC0
[  751.977134] g_audio gadget: we need at least one control device
[  751.988633] Unable to handle kernel paging request at virtual address 455f448e
[  751.995963] pgd = bd42c000
[  751.998681] [455f448e] *pgd=00000000
[  752.002383] Internal error: Oops: 5 [#1] SMP ARM
[  752.007008] Modules linked in: usb_f_uac1 g_audio(+) usb_f_mass_storage libcomposite configfs [last unloaded: g_mass_storage]
[  752.018427] CPU: 0 PID: 692 Comm: modprobe Not tainted 3.18.0-rc4-00345-g842f57ba #10
[  752.026176] task: bdb3ba80 ti: bd41a000 task.ti: bd41a000
[  752.031590] PC is at filp_close+0xc/0x84
[  752.035530] LR is at gaudio_cleanup+0x28/0x54 [usb_f_uac1]
[  752.041023] pc : [<800ec94c>]    lr : [<7f03c63c>]    psr: 20000013
[  752.041023] sp : bd41bcc8  ip : bd41bce8  fp : bd41bce4
[  752.052504] r10: 7f036234  r9 : 7f036220  r8 : 7f036500
[  752.057732] r7 : bd456480  r6 : 7f036500  r5 : 7f03626c  r4 : bd441000
[  752.064264] r3 : 7f03b3dc  r2 : 7f03cab0  r1 : 00000000  r0 : 455f4456
[  752.070798] Flags: nzCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment user
[  752.077938] Control: 10c5387d  Table: bd42c04a  DAC: 00000015
[  752.083688] Process modprobe (pid: 692, stack limit = 0xbd41a240)
[  752.089786] Stack: (0xbd41bcc8 to 0xbd41c000)
[  752.094152] bcc0:                   7f03b3dc bd441000 7f03626c 7f036500 bd41bcfc bd41bce8
[  752.102337] bce0: 7f03c63c 800ec94c 7f03b3dc bdaa6b00 bd41bd14 bd41bd00 7f03b3f4 7f03c620
[  752.110521] bd00: 7f03b3dc 7f03cbd4 bd41bd2c bd41bd18 7f00f88c 7f03b3e8 00000000 fffffffe
[  752.118705] bd20: bd41bd5c bd41bd30 7f0380d8 7f00f874 7f038000 bd456480 7f036364 be392240
[  752.126889] bd40: 00000000 7f00f620 7f00f638 bd41a008 bd41bd94 bd41bd60 7f00f6d4 7f03800c
[  752.135073] bd60: 00000001 00000000 8047438c be3a4000 7f036364 7f036364 7f00db28 7f00f620
[  752.143257] bd80: 7f00f638 bd41a008 bd41bdb4 bd41bd98 804742ac 7f00f644 00000000 809adde0
[  752.151442] bda0: 7f036364 7f036364 bd41bdcc bd41bdb8 804743c8 80474284 7f03633c 7f036200
[  752.159626] bdc0: bd41bdf4 bd41bdd0 7f00d5b4 8047435c bd41a000 80974060 7f038158 00000000
[  752.167811] bde0: 80974060 bdaa9940 bd41be04 bd41bdf8 7f03816c 7f00d518 bd41be8c bd41be08
[  752.175995] be00: 80008a5c 7f038164 be001f00 7f0363c4 bd41bf48 00000000 bd41be54 bd41be28
[  752.184179] be20: 800e9498 800e8e74 00000002 00000003 bd4129c0 c0a07000 00000001 7f0363c4
[  752.192363] be40: bd41bf48 00000000 bd41be74 bd41be58 800de780 800e9320 bd41a000 7f0363d0
[  752.200547] be60: 00000000 bd41a000 7f0363d0 00000000 bd41beec 7f0363c4 bd41bf48 00000000
[  752.208731] be80: bd41bf44 bd41be90 80093e54 800089e0 ffff8000 00007fff 80091390 0000065f
[  752.216915] bea0: 00000000 c0a0834c bd41bf7c 00000086 bd41bf50 00000000 7f03651c 00000086
[  752.225099] bec0: bd41a010 00c28758 800ddcc4 800ddae0 000000d2 bd412a00 bd41bf24 00000000
[  752.233283] bee0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[  752.241467] bf00: 00000000 00000000 00000000 00000000 00000000 00000000 bd41bf44 000025b0
[  752.249651] bf20: 00c28a08 00c28758 00000080 8000edc4 bd41a000 00000000 bd41bfa4 bd41bf48
[  752.257835] bf40: 800943e4 800932ec c0a07000 000025b0 c0a07f8c c0a07ea4 c0a08e5c 0000051c
[  752.266019] bf60: 0000088c 00000000 00000000 00000000 00000018 00000019 00000010 0000000b
[  752.274203] bf80: 00000009 00000000 00000000 000025b0 00000000 00c28758 00000000 bd41bfa8
[  752.282387] bfa0: 8000ec00 8009430c 000025b0 00000000 00c28a08 000025b0 00c28758 00c28980
[  752.290571] bfc0: 000025b0 00000000 00c28758 00000080 000a6a78 00000007 00c28718 00c28980
[  752.298756] bfe0: 7ebc1af0 7ebc1ae0 0001a32c 76e9c490 60000010 00c28a08 22013510 ecebffff
[  752.306933] Backtrace:
[  752.309414] [<800ec940>] (filp_close) from [<7f03c63c>] (gaudio_cleanup+0x28/0x54 [usb_f_uac1])
[  752.318115]  r6:7f036500 r5:7f03626c r4:bd441000 r3:7f03b3dc
[  752.323851] [<7f03c614>] (gaudio_cleanup [usb_f_uac1]) from [<7f03b3f4>] (f_audio_free_inst+0x18/0x68 [usb_f_uac1])
[  752.334288]  r4:bdaa6b00 r3:7f03b3dc
[  752.337931] [<7f03b3dc>] (f_audio_free_inst [usb_f_uac1]) from [<7f00f88c>] (usb_put_function_instance+0x24/0x30 [libcomposite])
[  752.349498]  r4:7f03cbd4 r3:7f03b3dc
[  752.353127] [<7f00f868>] (usb_put_function_instance [libcomposite]) from [<7f0380d8>] (audio_bind+0xd8/0xfc [g_audio])
[  752.363824]  r4:fffffffe r3:00000000
[  752.367456] [<7f038000>] (audio_bind [g_audio]) from [<7f00f6d4>] (composite_bind+0x9c/0x1e8 [libcomposite])
[  752.377284]  r10:bd41a008 r9:7f00f638 r8:7f00f620 r7:00000000 r6:be392240 r5:7f036364
[  752.385193]  r4:bd456480 r3:7f038000
[  752.388825] [<7f00f638>] (composite_bind [libcomposite]) from [<804742ac>] (udc_bind_to_driver+0x34/0xd8)
[  752.398394]  r10:bd41a008 r9:7f00f638 r8:7f00f620 r7:7f00db28 r6:7f036364 r5:7f036364
[  752.406302]  r4:be3a4000
[  752.408860] [<80474278>] (udc_bind_to_driver) from [<804743c8>] (usb_gadget_probe_driver+0x78/0xa8)
[  752.417908]  r6:7f036364 r5:7f036364 r4:809adde0 r3:00000000
[  752.423649] [<80474350>] (usb_gadget_probe_driver) from [<7f00d5b4>] (usb_composite_probe+0xa8/0xd4 [libcomposite])
[  752.434086]  r5:7f036200 r4:7f03633c
[  752.437713] [<7f00d50c>] (usb_composite_probe [libcomposite]) from [<7f03816c>] (audio_driver_init+0x14/0x1c [g_audio])
[  752.448498]  r9:bdaa9940 r8:80974060 r7:00000000 r6:7f038158 r5:80974060 r4:bd41a000
[  752.456330] [<7f038158>] (audio_driver_init [g_audio]) from [<80008a5c>] (do_one_initcall+0x88/0x1d4)
[  752.465564] [<800089d4>] (do_one_initcall) from [<80093e54>] (load_module+0xb74/0x1020)
[  752.473571]  r10:00000000 r9:bd41bf48 r8:7f0363c4 r7:bd41beec r6:00000000 r5:7f0363d0
[  752.481478]  r4:bd41a000
[  752.484037] [<800932e0>] (load_module) from [<800943e4>] (SyS_init_module+0xe4/0xf8)
[  752.491781]  r10:00000000 r9:bd41a000 r8:8000edc4 r7:00000080 r6:00c28758 r5:00c28a08
[  752.499689]  r4:000025b0
[  752.502252] [<80094300>] (SyS_init_module) from [<8000ec00>] (ret_fast_syscall+0x0/0x48)
[  752.510345]  r6:00c28758 r5:00000000 r4:000025b0
[  752.515013] Code: 808475b4 e1a0c00d e92dd878 e24cb004 (e5904038)
[  752.521223] ---[ end trace 70babe34de4ab99b ]---
Segmentation fault
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

!strncmp(buf, "force host", 9) is true if and only if buf starts with
"force hos". This was obviously not what was intended. The same error
exists for "force full-speed", "force high-speed" and "test
packet". Using strstarts avoids the error-prone hardcoding of the
prefix length.

For consistency, also change the other occurences of the !strncmp
idiom.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Felipe Balbi <balbi@ti.com>

commit cc92f681 (usb: musb: Populate new IO
functions for blackfin) added a typo which
prevented MUSB's blackfin glue layer from being
built. Due to lack of tests and compilers for
that architecture, the typo ended up being
merged and causing a build regression.

Fix that here

Cc: Tony Lindgren <tony@atomide.com>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Blackfin's MUSB implementation lacks a bunch of
registers which they end up not defining a macro
for. In order to avoid build breaks, let's ifdef
out some of the registers from our regdump debugfs
utility so that we don't try to use those on
Blackfin builds.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Pull ACCESS_ONCE cleanup preparation from Christian Borntraeger:
 "kernel: Provide READ_ONCE and ASSIGN_ONCE

  As discussed on LKML http://marc.info/?i=54611D86.4040306%40de.ibm.com
  ACCESS_ONCE might fail with specific compilers for non-scalar
  accesses.

  Here is a set of patches to tackle that problem.

  The first patch introduce READ_ONCE and ASSIGN_ONCE.  If the data
  structure is larger than the machine word size memcpy is used and a
  warning is emitted.  The next patches fix up several in-tree users of
  ACCESS_ONCE on non-scalar types.

  This does not yet contain a patch that forces ACCESS_ONCE to work only
  on scalar types.  This is targetted for the next merge window as Linux
  next already contains new offenders regarding ACCESS_ONCE vs.
  non-scalar types"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/borntraeger/linux:
  s390/kvm: REPLACE barrier fixup with READ_ONCE
  arm/spinlock: Replace ACCESS_ONCE with READ_ONCE
  arm64/spinlock: Replace ACCESS_ONCE READ_ONCE
  mips/gup: Replace ACCESS_ONCE with READ_ONCE
  x86/gup: Replace ACCESS_ONCE with READ_ONCE
  x86/spinlock: Replace ACCESS_ONCE with READ_ONCE
  mm: replace ACCESS_ONCE with READ_ONCE or barriers
  kernel: Provide READ_ONCE and ASSIGN_ONCE

Pull clk framework updates from Mike Turquette:
 "This is much later than usual due to several last minute bugs that had
  to be addressed.  As usual the majority of changes are new drivers and
  modifications to existing drivers.  The core recieved many fixes along
  with the groundwork for several large changes coming in the future
  which will better parition clock providers from clock consumers"

* tag 'clk-for-linus-3.19' of git://git.linaro.org/people/mike.turquette/linux: (86 commits)
  clk: samsung: Fix Exynos 5420 pinctrl setup and clock disable failure due to domain being gated
  ARM: OMAP3: clock: fix boot breakage in legacy mode
  ARM: OMAP2+: clock: fix DPLL code to use new determine rate APIs
  clk: Really fix deadlock with mmap_sem
  clk: mmp: fix sparse non static symbol warning
  clk: Change clk_ops->determine_rate to return a clk_hw as the best parent
  clk: change clk_debugfs_add_file to take a struct clk_hw
  clk: Don't expose __clk_get_accuracy
  clk: Don't try to use a struct clk* after it could have been freed
  clk: Remove unused function __clk_get_prepare_count
  clk: samsung: Fix double add of syscore ops after driver rebind
  clk: samsung: exynos4: set parent of sclk_hdmiphy to hdmi
  clk: samsung: exynos4415: Fix build with PM_SLEEP disabled
  clk: samsung: remove unnecessary inclusion of header files from clk.h
  clk: samsung: remove unnecessary CONFIG_OF from clk.c
  clk: samsung: Spelling s/bwtween/between/
  clk: rockchip: Add support for the mmc clock phases using the framework
  clk: rockchip: add bindings for the mmc clocks
  clk: rockchip: rk3288 export i2s0_clkout for use in DT
  clk: rockchip: use clock ID for DMC (memory controller) on rk3288
  ...

Pull more i2c updates from Wolfram Sang:
 "Included are two bugfixes needing some bigger refactoring (sh_mobile:
  deferred probe with DMA, mv64xxx: fix offload support) and one
  deprecated driver removal I thought would go in via ppc but I
  misunderstood.  It has a proper ack from BenH"

* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: sh_mobile: fix uninitialized var when debug is enabled
  macintosh: therm_pm72: delete deprecated driver
  i2c: sh_mobile: I2C_SH_MOBILE should depend on HAS_DMA
  i2c: sh_mobile: rework deferred probing
  i2c: sh_mobile: refactor DMA setup
  i2c: mv64xxx: rework offload support to fix several problems
  i2c: mv64xxx: use BIT() macro for register value definitions

Pull SCSI update from James Bottomley:
 "This is a much shorter set of patches that were on the go but didn't
  make it in to the early pull request for the merge window.  It's
  really a set of bug fixes plus some final cleanup work on the new tag
  queue API"

* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  storvsc: ring buffer failures may result in I/O freeze
  ipr: set scsi_level correctly for disk arrays
  ipr: add support for async scanning to speed up boot
  scsi_debug: fix missing "break;" in SDEBUG_UA_CAPACITY_CHANGED case
  scsi_debug: take sdebug_host_list_lock when changing capacity
  scsi_debug: improve driver description in Kconfig
  scsi_debug: fix compare and write errors
  qla2xxx: fix race in handling rport deletion during recovery causes panic
  scsi: blacklist RSOC for Microsoft iSCSI target devices
  scsi: fix random memory corruption with scsi-mq + T10 PI
  Revert "[SCSI] mpt3sas: Remove phys on topology change"
  Revert "[SCSI] mpt2sas: Remove phys on topology change."
  esas2r: Correct typos of "validate" in a comment
  fc: FCP_PTA_SIMPLE is 0
  ibmvfc: remove unused tag variable
  scsi: remove MSG_*_TAG defines
  scsi: remove scsi_set_tag_type
  scsi: remove scsi_get_tag_type
  scsi: never drop to untagged mode during queue ramp down
  scsi: remove ->change_queue_type method

Pull CONFIG_PM_RUNTIME elimination from Rafael Wysocki:
 "This removes the last few uses of CONFIG_PM_RUNTIME introduced
  recently and makes that config option finally go away.

  CONFIG_PM will be available directly from the menu now and also it
  will be selected automatically if CONFIG_SUSPEND or CONFIG_HIBERNATION
  is set"

* tag 'pm-config-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  PM: Eliminate CONFIG_PM_RUNTIME
  tty: 8250_omap: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  sound: sst-haswell-pcm: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  spi: Replace CONFIG_PM_RUNTIME with CONFIG_PM

Pull misc kbuild changes from Michal Marek:
 "There are only a few things in the misc branch:

   - Fix for bugon.cocci semantic patch
   - Kdevelop4 files are .gitignored
   - Put make binrpm-pkg on diet"

* 'misc' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
  scripts/package: binrpm-pkg do not create source and devel package
  .gitignore: Add Kdevelop4 project files
  bugon.cocci: fix Options at the macro

Pull kbuild updates from Michal Marek:
 "Here are the kbuild changes for v3.19-rc1:

   - Cleanups and deduplication in the main Makefile and
     scripts/Makefile.*
   - Sort the output of *config targets in make help
   - Old <linux/version.h> is always removed to avoid a surprise during
     bisecting
   - Warning fix in kconfig"

* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
  kbuild: remove redundant -rR flag of hdr-inst
  kbuild: Fix make help-<board series> on powerpc
  kbuild: Automatically remove stale <linux/version.h> file
  kconfig: Fix warning "‘jump’ may be used uninitialized"
  Makefile: sort list of defconfig targets in make help output
  kbuild: Remove duplicate $(cmd) definition in Makefile.clean
  kbuild: collect shorthands into scripts/Kbuild.include

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Pull vfs pile #3 from Al Viro:
 "Assorted fixes and patches from the last cycle"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  [regression] chunk lost from bd9b51
  vfs: make mounts and mountstats honor root dir like mountinfo does
  vfs: cleanup show_mountinfo
  init: fix read-write root mount
  unfuck binfmt_misc.c (broken by commit e6084d4a)
  vm_area_operations: kill ->migrate()
  new helper: iter_is_iovec()
  move_extent_per_page(): get rid of unused w_flags
  lustre: get rid of playing with ->fs
  btrfs: filp_open() returns ERR_PTR() on failure, not NULL...

Merge tag 'ecryptfs-3.19-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs

Pull eCryptfs fixes from Tyler Hicks:
 "Fixes for filename decryption and encrypted view plus a cleanup

   - The filename decryption routines were, at times, writing a zero
     byte one character past the end of the filename buffer

   - The encrypted view feature attempted, and failed, to roll its own
     form of enforcing a read-only mount instead of letting the VFS
     enforce it"

* tag 'ecryptfs-3.19-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
  eCryptfs: Remove buggy and unnecessary write in file name decode routine
  eCryptfs: Remove unnecessary casts when parsing packet lengths
  eCryptfs: Force RO mount when encrypted view is enabled

Pull more btrfs updates from Chris Mason:
 "This is part two of our merge window patches.

  These are all from Filipe, and fix some really hard to find races that
  can cause corruptions.  Most of them involved block group removal
  (balance) or discard"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: remove non-sense btrfs_error_discard_extent() function
  Btrfs: fix fs corruption on transaction abort if device supports discard
  Btrfs: always clear a block group node when removing it from the tree
  Btrfs: ensure deletion from pinned_chunks list is protected

Pull sound fixes from Takashi Iwai:
 "Here are a few fixes that have landed after the previous pull request.
  All are driver specific fixes including:

   - error/int value fixes in OXFW,
   - Intel Skylake HD-audio HDMI codec support,
   - Additional HD-audio Realtek codecs and AD1986A codec fixes/quirks,
   - a few more DSD support and a quirk for Arcam rPAC in usb-audio,
   - a typo fix for Scarlett 6i6,
   - fixes for new ASIHPI firmware,
   - ASoC Exynos7 cleanups,
   - Intel ACPI support, and
   - a fix for PCM512 register cache sync"

* tag 'sound-fix-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (24 commits)
  ALSA: usb-audio: extend KEF X300A FU 10 tweak to Arcam rPAC
  ALSA: hda/realtek - New codec support for ALC298
  ALSA: asihpi: update to HPI version 4.14
  ALSA: asihpi: increase tuner pad cache size
  ALSA: asihpi: relax firmware version check
  ALSA: usb-audio: Fix Scarlett 6i6 initialization typo
  ALSA: hda - Add quirk for Packard Bell EasyNote MX65
  ALSA: usb-audio: add native DSD support for Matrix Audio DACs
  ALSA: hda/realtek - New codec support for ALC256
  ALSA: hda/realtek - Add new Dell desktop for ALC3234 headset mode
  ASoC: Intel: fix possible acpi enumeration panic
  ALSA: hda/hdmi - apply Haswell fix-ups to Skylake display codec
  ASoC: Intel: fix return value check in sst_acpi_probe()
  ALSA: hda - Make add_stereo_mix_input flag tristate
  ALSA: hda - Create capture source ctls when stereo mix input is added
  ALSA: hda - Fix typos in snd_hda_get_int_hint() kerneldoc comments
  ALSA: hda - add codec ID for Skylake display audio codec
  ALSA: oxfw: some signedness bugs
  ALSA: oxfw: fix detect_loud_models() return value
  ASoC: rt5677: add REGMAP_I2C and REGMAP_IRQ dependency
  ...

Pull SCSI target fixes from Nicholas Bellinger:
 "The highlights this merge window include:

   - Allow target fabric drivers to function as built-in.  (Roland)
   - Fix tcm_loop multi-TPG endpoint nexus bug.  (Hannes)
   - Move per device config_item_type into se_subsystem_api, allowing
     configfs attributes to be defined at module_init time.  (Jerome +
     nab)
   - Convert existing IBLOCK/FILEIO/RAMDISK/PSCSI/TCMU drivers to use
     external configfs attributes.  (nab)
   - A number of iser-target fixes related to active session + network
     portal shutdown stability during extended stress testing.  (Sagi +
     Slava)
   - Dynamic allocation of T10-PI contexts for iser-target, fixing a
     potentially bogus iscsi_np->tpg_np pointer reference in >= v3.14
     code.  (Sagi)
   - iser-target performance + scalability improvements.  (Sagi)
   - Fixes for SPC-4 Persistent Reservation AllRegistrants spec
     compliance.  (Ilias + James + nab)
   - Avoid potential short kern_sendmsg() in iscsi-target for now until
     Al's conversion to use msghdr iteration is merged post -rc1.
     (Viro)

  Also, Sagi has requested a number of iser-target patches (9) that
  address stability issues he's encountered during extended stress
  testing be considered for v3.10.y + v3.14.y code.  Given the amount of
  LOC involved, it will certainly require extra backporting effort.

  Apologies in advance to Greg-KH & Co on this.  Sagi and I will be
  working post-merge to ensure they each get applied correctly"

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (53 commits)
  target: Allow AllRegistrants to re-RESERVE existing reservation
  uapi/linux/target_core_user.h: fix headers_install.sh badness
  iscsi-target: Fail connection on short sendmsg writes
  iscsi-target: nullify session in failed login sequence
  target: Avoid dropping AllRegistrants reservation during unregister
  target: Fix R_HOLDER bit usage for AllRegistrants
  iscsi-target: Drop left-over bogus iscsi_np->tpg_np
  iser-target: Fix wc->wr_id cast warning
  iser-target: Remove code duplication
  iser-target: Adjust log levels and prettify some prints
  iser-target: Use debug_level parameter to control logging level
  iser-target: Fix logout sequence
  iser-target: Don't wait for session commands from completion context
  iser-target: Reduce CQ lock contention by batch polling
  iser-target: Introduce isert_poll_budget
  iser-target: Remove an atomic operation from the IO path
  iser-target: Remove redundant call to isert_conn_terminate
  iser-target: Use single CQ for TX and RX
  iser-target: Centralize completion elements to a context
  iser-target: Cast wr_id with uintptr_t instead of unsinged long
  ...

Pull arch/hexagon updates from Richard Kuo:
 "Build cleanup and a few misc fixes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rkuo/linux-hexagon-kernel:
  Hexagon: fix signal delivery for debug traps
  Hexagon: set ARCH_DMA_MINALIGN
  Hexagon: fix alignment of init_task in RW_DATA_SECTION
  hexagon: Fix build failures in linux-next

Pull arch/chris updates from Jesper Nilsson:
 "Mostly cleanup and build fixes for CRISv32 allmodconfig

  God Jul och Gott Nytt år!"

* tag 'cris-changes-for-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris:
  CRISv32: Remove last remnants of ETRAX_SPI_MMC_BOARD
  CRISv32: ETRAXFS: Fix recursive spinlock
  CRISv32: Select MTDRAM for axisflashmap
  CRISv32: Implement early console
  CRIS: Use KALLSYMs if available in call stack dump
  CRISv32: Fix declaration mismatch
  CRISv32: Rewrite of synchronous serial port driver
  CRIS: Update init memory handling
  CRISv32: Better handling of watchdog bite
  CRIS: Export missing function symbols
  CRIS: Export ioremap_nocache
  CRIS: Fix headers_install
  CRISv32: Add missing include for mm.h
  CRISv32: Drop obsolete file for SPI driver

Pull ia64 __get_cpu_var removal from Tony Luck:
 "__get_cpu_var removed from rest of tree, drop reference from comments
  in arch/ia64"

* tag 'please-pull-misc-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
  [IA64] Update comment that references __get_cpu_var