This patch adds support for the watchdog hardware found in A31 and
newer SoCs. This new hardware has registers at different offsets, and
the system reset control has been split out of the "mode" register
into a new "configuration" register.

Differences not supported by this driver include separate interrupt
lines for each watchdog, instead of sharing an interrupt line and
registers with the timer block.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

This patch adds support for hardware parameters tied to compatible
strings, so similar hardware can reuse the driver.

This will be used to support the newer watchdog found in A31 and
later SoCs. Differences in the new hardware include separate
interrupt lines for each watchdog, and corresponding interrupt
control/status registers. Watchdog control registers were also
slightly rearranged.

Also replace ioread32()/iowrite32() with readl()/writel() in various
places changed.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

  Register the watchdog as the system restart function
to the new introducing kernel restart call chain in the
driver instead of providing the restart in machine desc.
  This restart handler function is from the mxc_restart()
in arch/arm/mach-imx/system.c
Signed-off-by: Jingchang Lu <jingchang.lu@freescale.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

The WDT's BITE_TIME warm-reset behavior can be leveraged as a last
resort mechanism for triggering chip reset.  Usually, other restart
methods (such as PS_HOLD) are preferrable for issuing a more complete
reset of the chip.  As such, keep the priority of the watchdog notifier
low.
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

On a lot of Samsung systems the watchdog is responsible for restarting the
system and until now this code was contained in plat-samsung/watchdog-reset.c.

With the introduction of the restart handlers, this code can now move into
driver itself, removing the need for arch-specific code.

Tested on a S3C2442 based GTA02
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

The kernel core now provides an API to trigger a system restart.
Register with it to support restarting the system via. watchdog.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Update the multi_v7_defconfig enabling the watchdog driver for Meson
SoCs.
Signed-off-by: Carlo Caione <carlo@caione.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

This patch adds the watchdog driver for the Amlogic Meson SoCs used also
to reboot the device.
Signed-off-by: Carlo Caione <carlo@caione.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Signed-off-by: Carlo Caione <carlo@caione.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

There is no conflict with rtc/rtc-stmp3xxx.c parent
because modified registers in PM functions of stmp3xxx_rtc_wdt
are different.
Signed-off-by: Janusz Uzycki <j.uzycki@elproma.com.pl>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

This driver supports the watchdog device inside the DA9063 PMIC.
Signed-off-by: Krystian Garbaciak <krystian.garbaciak@diasemi.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Tested-by: Steve Twiss <stwiss.opensource@diasemi.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

This adds a driver for the watchdog timer available in Ricoh RN5T618
PMIC. The device supports a programmable expiration time of 1, 8, 32
or 128 seconds.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Exynos7 SoC has a Watchdog for Atlas (A57) cores
This patch adds support for the Atlas watchdog.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

The Qualcomm Krait Processor Sub-system (KPSS) contains one or more
instances of the WDT.  Provide documentation on how to describe these in
the device tree.
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Add a driver for the watchdog timer block found in the Krait Processor
Subsystem (KPSS) on the MSM8960, APQ8064, and IPQ8064.
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

The TOP_INIT, ie bit 4-7 of the WDOG_TIMEOUT_RANGE_REG_OFFSET register
may be zero, so the timeout period may be very short after initialization
is done, thus the system may be reset soon after enabling. We fix this
problem by also initialising the TOP_INIT when setting TOP in function
dw_wdt_set_top().
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Add cadence-wdt bindings documentation.
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Add Cadence WDT driver. This is used by Xilinx Zynq.
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Signed-off-by: Uwe Kleine-K=C3=B6nig <u.kleine-koenig@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

There is no need to store the return value of misc_deregister() in a
variable. Instead we can just return the value directly.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Building booke_wdt fails when trying to build as a module as there is no
early_param() in module. Fix by using module_param() instead of early_param().
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

There is no need to init .owner field.

Based on the patch from Peter Griffin <peter.griffin@linaro.org>
"mmc: remove .owner field for drivers using module_platform_driver"

This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway."
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Pull ARM SoC fixes from Olof Johansson:
 "A batch of fixes that have come in during the merge window.

  Some of them are defconfig updates for things that have now landed,
  some errata additions and a few general scattered fixes.

  There's also a qcom DT update that adds support for SATA on AP148, and
  basic support for Sony Xperia Z1 and CM-QS600 platforms that seemed
  isolated enough that we could merge it even if it's late"

* tag 'arm-soc-fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  MAINTAINERS: corrected bcm2835 search
  ARM: dts: Explicitly set dr_mode on exynos5420-arndale-octa
  ARM: dts: Explicitly set dr_mode on exynos Peach boards
  ARM: dts: qcom: add CM-QS600 board
  ARM: dts: qcom: Add initial DTS file for Sony Xperia Z1 phone
  ARM: dts: qcom: Add SATA support on IPQ8064/AP148
  MAINTAINERS: Update Santosh Shilimkar's email id
  ARM: sunxi_defconfig: enable CONFIG_REGULATOR
  ARM: dts: Disable smc91x on n900 until bootloader dependency is removed
  ARM: omap2plus_defconfig: Enable ARM erratum 430973 for omap3
  ARM: exynos_defconfig: enable USB gadget support
  ARM: exynos_defconfig: Enable Maxim 77693 and I2C GPIO drivers
  ARM: mm: Fix ifdef around cpu_*_do_[suspend, resume] ops
  ARM: EXYNOS: Fix build with PM_SLEEP=n and ARM_EXYNOS_CPUIDLE=n
  ARM: SAMSUNG: Restore Samsung PM Debug functionality
  ARM: dts: Fix pull setting in sd4_width8 pin group for exynos4x12
  ARM: exynos_defconfig: Enable SBS battery support
  ARM: exynos_defconfig: Enable Control Groups support
  ARM: exynos_defconfig: Enable Atmel maXTouch support
  ARM: exynos_defconfig: Enable MAX77802

Pull audit updates from Eric Paris:
 "So this change across a whole bunch of arches really solves one basic
  problem.  We want to audit when seccomp is killing a process.  seccomp
  hooks in before the audit syscall entry code.  audit_syscall_entry
  took as an argument the arch of the given syscall.  Since the arch is
  part of what makes a syscall number meaningful it's an important part
  of the record, but it isn't available when seccomp shoots the
  syscall...

  For most arch's we have a better way to get the arch (syscall_get_arch)
  So the solution was two fold: Implement syscall_get_arch() everywhere
  there is audit which didn't have it.  Use syscall_get_arch() in the
  seccomp audit code.  Having syscall_get_arch() everywhere meant it was
  a useless flag on the stack and we could get rid of it for the typical
  syscall entry.

  The other changes inside the audit system aren't grand, fixed some
  records that had invalid spaces.  Better locking around the task comm
  field.  Removing some dead functions and structs.  Make some things
  static.  Really minor stuff"

* git://git.infradead.org/users/eparis/audit: (31 commits)
  audit: rename audit_log_remove_rule to disambiguate for trees
  audit: cull redundancy in audit_rule_change
  audit: WARN if audit_rule_change called illegally
  audit: put rule existence check in canonical order
  next: openrisc: Fix build
  audit: get comm using lock to avoid race in string printing
  audit: remove open_arg() function that is never used
  audit: correct AUDIT_GET_FEATURE return message type
  audit: set nlmsg_len for multicast messages.
  audit: use union for audit_field values since they are mutually exclusive
  audit: invalid op= values for rules
  audit: use atomic_t to simplify audit_serial()
  kernel/audit.c: use ARRAY_SIZE instead of sizeof/sizeof[0]
  audit: reduce scope of audit_log_fcaps
  audit: reduce scope of audit_net_id
  audit: arm64: Remove the audit arch argument to audit_syscall_entry
  arm64: audit: Add audit hook in syscall_trace_enter/exit()
  audit: x86: drop arch from __audit_syscall_entry() interface
  sparc: implement is_32bit_task
  sparc: properly conditionalize use of TIF_32BIT
  ...

Merge tag 'qcom-dt-for-3.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom into fixes

Merge "qcom DT changes for v3.18-3" from Kumar Gala:

Qualcomm ARM Based Device Tree Updates for v3.18-3

* Added Board support for CM-QS600 and Sony Xperia Z1 phone
* Added SATA support on IPQ8064/AP148

* tag 'qcom-dt-for-3.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom:
  ARM: dts: qcom: add CM-QS600 board
  ARM: dts: qcom: Add initial DTS file for Sony Xperia Z1 phone
  ARM: dts: qcom: Add SATA support on IPQ8064/AP148

Merge tag 'samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes

Pull more fixes from Kukjin Kim:

2nd Samsung fixes for v3.18
- Explicitly set dr_mode on exynos5800-peach-pi, exynos5420-peach-pit
  and exynos5420-arndale-octa boards, because the USB dwc3 controller
  will not work properly without dr_mode as host on above boards if
  the USB host and gadget are enabled in kernel configuration both.

* tag 'samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
  ARM: dts: Explicitly set dr_mode on exynos5420-arndale-octa
  ARM: dts: Explicitly set dr_mode on exynos Peach boards
Signed-off-by: Olof Johansson <olof@lixom.net>

Corrected bcm2835 maintainer info by using N: to specify any files with
bcm2835 in are directed to the proper maintainer.
Also corrected minor mispelling of ARCHITECTURE in 2 comment locations.
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

Pull ntb (non-transparent bridge) updates from Jon Mason:
 "Add support for Haswell NTB split BARs, a debugfs entry for basic
  debugging info, and some code clean-ups"

* tag 'ntb-3.18' of git://github.com/jonmason/ntb:
  ntb: Adding split BAR support for Haswell platforms
  ntb: use errata flag set via DID to implement workaround
  ntb: conslidate reading of PPD to move platform detection earlier
  ntb: move platform detection to separate function
  NTB: debugfs device entry

Pull i2c updates from Wolfram Sang:
 "Highlights from the I2C subsystem for 3.18:

   - new drivers for Axxia AM55xx, and Hisilicon hix5hd2 SoC.

   - designware driver gained AMD support, exynos gained exynos7 support

  The rest is usual driver stuff.  Hopefully no lowlights this time"

* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: i801: Add Device IDs for Intel Sunrise Point PCH
  i2c: hix5hd2: add i2c controller driver
  i2c-imx: Disable the clock on probe failure
  i2c: designware: Add support for AMD I2C controller
  i2c: designware: Rework probe() to get clock a bit later
  i2c: designware: Default to fast mode in case of ACPI
  i2c: axxia: Add I2C driver for AXM55xx
  i2c: exynos: add support for HSI2C module on Exynos7
  i2c: mxs: detect No Slave Ack on SELECT in PIO mode
  i2c: cros_ec: Remove EC_I2C_FLAG_10BIT
  i2c: cros-ec-tunnel: Add of match table
  i2c: rcar: remove sign-compare flaw
  i2c: ismt: Use minimum descriptor size
  i2c: imx: Add arbitration lost check
  i2c: rk3x: Remove unlikely() annotations
  i2c: rcar: check for no IRQ in rcar_i2c_irq()
  i2c: rcar: make rcar_i2c_prepare_msg() *void*
  i2c: rcar: simplify check for last message
  i2c: designware: add support of platform data to set I2C mode
  i2c: designware: add support of I2C standard mode

Pull sound fixes from Takashi Iwai:
 "Here are a collection of small fixes after 3.18 merge.

  The urgent one is the fix for kernel panics with linked PCM substream
  triggered by the recent nonatomic PCM ops support.  Other two fixes
  (emu10k1 and bebob) are stable fixes, and one easy PCI ID addition for
  a new Intel HD-audio controller"

* tag 'sound-fix-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda_intel: Add Device IDs for Intel Sunrise Point PCH
  ALSA: emu10k1: Fix deadlock in synth voice lookup
  ALSA: pcm: Fix referred substream in snd_pcm_action_group() unlock loop
  ALSA: bebob: Fix failure to detect source of clock for Terratec Phase 88

Pull second round of input updates from Dmitry Torokhov:
 "Mostly simple bug fixes, although we do have one brand new driver for
  Microchip AR1021 i2c touchscreen.

  Also there is the change to stop trying to use i8042 active
  multiplexing by default (it is still possible to activate it via
  i8042.nomux=0 on boxes that implement it)"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: xpad - add Thrustmaster as Xbox 360 controller vendor
  Input: xpad - add USB ID for Thrustmaster Ferrari 458 Racing Wheel
  Input: max77693-haptic - fix state check in imax77693_haptic_disable()
  Input: xen-kbdfront - free grant table entry in xenkbd_disconnect_backend
  Input: alps - fix v4 button press recognition
  Input: i8042 - disable active multiplexing by default
  Input: i8042 - add noloop quirk for Asus X750LN
  Input: synaptics - gate forcepad support by DMI check
  Input: Add Microchip AR1021 i2c touchscreen
  Input: cros_ec_keyb - add of match table
  Input: serio - avoid negative serio device numbers
  Input: avoid negative input device numbers
  Input: automatically set EV_ABS bit in input_set_abs_params
  Input: adp5588-keys - cancel workqueue in failure path
  Input: opencores-kbd - switch to using managed resources
  Input: evdev - fix EVIOCG{type} ioctl

Pull infiniband/RDMA updates from Roland Dreier:
 - large set of iSER initiator improvements
 - hardware driver fixes for cxgb4, mlx5 and ocrdma
 - small fixes to core midlayer

* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (47 commits)
  RDMA/cxgb4: Fix ntuple calculation for ipv6 and remove duplicate line
  RDMA/cxgb4: Add missing neigh_release in find_route
  RDMA/cxgb4: Take IPv6 into account for best_mtu and set_emss
  RDMA/cxgb4: Make c4iw_wr_log_size_order static
  IB/core: Fix XRC race condition in ib_uverbs_open_qp
  IB/core: Clear AH attr variable to prevent garbage data
  RDMA/ocrdma: Save the bit environment, spare unncessary parenthesis
  RDMA/ocrdma: The kernel has a perfectly good BIT() macro - use it
  RDMA/ocrdma: Don't memset() buffers we just allocated with kzalloc()
  RDMA/ocrdma: Remove a unused-label warning
  RDMA/ocrdma: Convert kernel VA to PA for mmap in user
  RDMA/ocrdma: Get vlan tag from ib_qp_attrs
  RDMA/ocrdma: Add default GID at index 0
  IB/mlx5, iser, isert: Add Signature API additions
  Target/iser: Centralize ib_sig_domain setting
  IB/iser: Centralize ib_sig_domain settings
  IB/mlx5: Use extended internal signature layout
  IB/iser: Set IP_CSUM as default guard type
  IB/iser: Remove redundant assignment
  IB/mlx5: Use enumerations for PI copy mask
  ...

Pull more perf updates from Ingo Molnar:
 "A second (and last) round of late coming fixes and changes, almost all
  of them in perf tooling:

  User visible tooling changes:

   - Add period data column and make it default in 'perf script' (Jiri
     Olsa)

   - Add a visual cue for toggle zeroing of samples in 'perf top'
     (Taeung Song)

   - Improve callchains when using libunwind (Namhyung Kim)

  Tooling fixes and infrastructure changes:

   - Fix for double free in 'perf stat' when using some specific invalid
     command line combo (Yasser Shalabi)

   - Fix off-by-one bugs in map->end handling (Stephane Eranian)

   - Fix off-by-one bug in maps__find(), also related to map->end
     handling (Namhyung Kim)

   - Make struct symbol->end be the first addr after the symbol range,
     to make it match the convention used for struct map->end.  (Arnaldo
     Carvalho de Melo)

   - Fix perf_evlist__add_pollfd() error handling in 'perf kvm stat
     live' (Jiri Olsa)

   - Fix python test build by moving callchain_param to an object linked
     into the python binding (Jiri Olsa)

   - Document sysfs events/ interfaces (Cody P Schafer)

   - Fix typos in perf/Documentation (Masanari Iida)

   - Add missing 'struct option' forward declaration (Arnaldo Carvalho
     de Melo)

   - Add option to copy events when queuing for sorting across cpu
     buffers and enable it for 'perf kvm stat live', to avoid having
     events left in the queue pointing to the ring buffer be rewritten
     in high volume sessions.  (Alexander Yarygin, improving work done
     by David Ahern):

   - Do not include a struct hists per perf_evsel, untangling the
     histogram code from perf_evsel, to pave the way for exporting a
     minimalistic tools/lib/api/perf/ library usable by tools/perf and
     initially by the rasd daemon being developed by Borislav Petkov,
     Robert Richter and Jean Pihet.  (Arnaldo Carvalho de Melo)

   - Make perf_evlist__open(evlist, NULL, NULL), i.e. without cpu and
     thread maps mean syswide monitoring, reducing the boilerplate for
     tools that only want system wide mode.  (Arnaldo Carvalho de Melo)

   - Move exit stuff from perf_evsel__delete to perf_evsel__exit, delete
     should be just a front end for exit + free (Arnaldo Carvalho de
     Melo)

   - Add support to new style format of kernel PMU event.  (Kan Liang)

  and other misc fixes"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (45 commits)
  perf script: Add period as a default output column
  perf script: Add period data column
  perf evsel: No need to drag util/cgroup.h
  perf evlist: Add missing 'struct option' forward declaration
  perf evsel: Move exit stuff from __delete to __exit
  kprobes/x86: Remove stale ARCH_SUPPORTS_KPROBES_ON_FTRACE define
  perf kvm stat live: Enable events copying
  perf session: Add option to copy events when queueing
  perf Documentation: Fix typos in perf/Documentation
  perf trace: Use thread_{,_set}_priv helpers
  perf kvm: Use thread_{,_set}_priv helpers
  perf callchain: Create an address space per thread
  perf report: Set callchain_param.record_mode for future use
  perf evlist: Fix for double free in tools/perf stat
  perf test: Add test case for pmu event new style format
  perf tools: Add support to new style format of kernel PMU event
  perf tools: Parse the pmu event prefix and suffix
  Revert "perf tools: Default to cpu// for events v5"
  perf Documentation: Remove Ruplicated docs for powerpc cpu specific events
  perf Documentation: sysfs events/ interfaces
  ...

Pull sparc fixes from David Miller:
 "Here we have two bug fixes:

  1) The current thread's fault_code is not setup properly upon entry to
     do_sparc64_fault() in some paths, leading to spurious SIGBUS.

  2) Don't use a zero length array at the end of thread_info on sparc64,
     otherwise end_of_stack() isn't right"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc64: Do not define thread fpregs save area as zero-length array.
  sparc64: Fix corrupted thread fault code.

Pull networking fixes from David Miller:
 "A quick batch of bug fixes:

  1) Fix build with IPV6 disabled, from Eric Dumazet.

  2) Several more cases of caching SKB data pointers across calls to
     pskb_may_pull(), thus referencing potentially free'd memory.  From
     Li RongQing.

  3) DSA phy code tests operation presence improperly, instead of going:

        if (x->ops->foo)
                r = x->ops->foo(args);

     it was going:

        if (x->ops->foo(args))
                r = x->ops->foo(args);

   Fix from Andew Lunn"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  Net: DSA: Fix checking for get_phy_flags function
  ipv6: fix a potential use after free in sit.c
  ipv6: fix a potential use after free in ip6_offload.c
  ipv4: fix a potential use after free in gre_offload.c
  tcp: fix build error if IPv6 is not enabled

The check for the presence or not of the optional switch function
get_phy_flags() called the function, rather than checked to see if it
is a NULL pointer. This causes a derefernce of a NULL pointer on all
switch chips except the sf2, the only switch to implement this call.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Fixes: 6819563e ("net: dsa: allow switch drivers to specify phy_device::dev_flags")
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This breaks the stack end corruption detection facility.

What that facility does it write a magic value to "end_of_stack()"
and checking to see if it gets overwritten.

"end_of_stack()" is "task_thread_info(p) + 1", which for sparc64 is
the beginning of the FPU register save area.

So once the user uses the FPU, the magic value is overwritten and the
debug checks trigger.

Fix this by making the size explicit.

Due to the size we use for the fpsaved[], gsr[], and xfsr[] arrays we
are limited to 7 levels of FPU state saves.  So each FPU register set
is 256 bytes, allocate 256 * 7 for the fpregs area.
Reported-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>

Every path that ends up at do_sparc64_fault() must install a valid
FAULT_CODE_* bitmask in the per-thread fault code byte.

Two paths leading to the label winfix_trampoline (which expects the
FAULT_CODE_* mask in register %g4) were not doing so:

1) For pre-hypervisor TLB protection violation traps, if we took
   the 'winfix_trampoline' path we wouldn't have %g4 initialized
   with the FAULT_CODE_* value yet.  Resulting in using the
   TLB_TAG_ACCESS register address value instead.

2) In the TSB miss path, when we notice that we are going to use a
   hugepage mapping, but we haven't allocated the hugepage TSB yet, we
   still have to take the window fixup case into consideration and
   in that particular path we leave %g4 not setup properly.

Errors on this sort were largely invisible previously, but after
commit 4ccb9272 ("sparc64: sun4v TLB
error power off events") we now have a fault_code mask bit
(FAULT_CODE_BAD_RA) that triggers due to this bug.

FAULT_CODE_BAD_RA triggers because this bit is set in TLB_TAG_ACCESS
(see #1 above) and thus we get seemingly random bus errors triggered
for user processes.

Fixes: 4ccb9272 ("sparc64: sun4v TLB error power off events")
Reported-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>