Merge tag 'iio-for-4.21b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next

Jonathan writes:

Second set of IIO new device support, features and cleanups for the 4.21 cycle.

Staging graduation
* ad2s90
  - Driver for this resolver to digital chip.

New drivers and device support.
* ad5686
  - Add support for ad5310r DAC and associated fix in value read back.
* exynos-adc
  - Support for S5PV210 which is slightly different from other parts.
* mcp41010
  - Driver supporting MCP41010, MCP41050, MCP41100, MCP42010, MCP42050 and
  MCP42100 microchip potentiometers.

New ACPI ids.
* ak8975
  - AKM9911 ACPI HID.
* kxcjk-1013
  - KXJ2109 ACPI HID.
  - KIOX010A ACPI HID.

New features
* ad5933
  - Explicit DT binding.
* ad2s90
  - Explicit DT binding including dropping spi setup that is done via dt
    in favour of verifying the settings form DT.
* adt7316
  - Explicit DT binding and support for gpio, irq_flags etc.
* stm32-adc
  - Runtime power management.

Minor fixes and cleanups
* core
  - Protect against missing info structure.
* ad2s90
  - SPDX
  - Add documentation fo the mutex.
* ad7280a
  - Check allocation failure.
  - Fix an accidental replacement of an error return.
* adt7316
  - Switch some variables to be local and rename for consistency with other
    drivers.
  - Revert a false handling of 0 as an error introduced earlier this cycle.
* bmi160
  - Use devm functions throughout probe() to avoid need for remove().
* hid-sensor-hub
  - White space cleanup.
* hts221
  - MAINTAINERS entry.
* lis302
  - Use generic name in the DT binding doc.
* Messon-saradc
  - Check for allocation error.
  - Fix some presented clock names that break clk debugfs.
* qcom-spmi-adc
  - A fix for initialization of the prescale property. Came late in the
    cycle, so merge window is probably the best route for this.
* st_lsm6dsx
  - Allow for variable read length to support wider range of slave devices.

* tag 'iio-for-4.21b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (37 commits)
  iio: adc: qcom-spmi-adc5: Initialize prescale properly
  dt-bindings: iio: adc: exynos-adc: Add S5PV210 variant
  iio: adc: Allow selection of Exynos ADC on S5PV210
  iio: adc: exynos-adc: Add S5PV210 variant
  iio: bmi160: use all devm functions in probe
  iio: dac: ad5686: fix bit shift read register
  iio:dac:ad5686: Add AD5310R support
  Revert "Staging: iio: adt7316: Add an extra check for 'ret' equals to 0"
  dt-bindings: iio: accel: use a generic node name for lis302
  iio: core: check 'info' value before registering the device
  staging: iio: adc: ad7280a: fix overwrite of the returned value
  staging: iio: adc: ad7280a: check for devm_kasprint() failure
  iio: humidity: hts221: add entry in MAINTAINERS file
  iio: magnetometer: ak8975: Add the "AKM9911" ACPI HID
  staging:iio:ad2s90: Move out of staging
  staging:iio:ad2s90: Add comment to device state mutex
  staging:iio:ad2s90: Replace license text w/ SPDX identifier
  dt-bindings:iio:resolver: Add docs for ad2s90
  staging:iio:ad2s90: Add max frequency check at probe
  staging:iio:ad2s90: Remove spi setup that should be done via dt
  ...

adc5_get_dt_data uses a local, prop, feeds it to adc5_get_dt_channel_data,
and then puts the result into adc->chan_props. The problem is
adc5_get_dt_channel_data may not initialize that structure fully, so a
garbage value is used for prescale if the optional "qcom,pre-scaling" is
not defined in DT. adc5_read_raw then uses this as an array index,
generating a crash that looks like this:

[    6.683186] Unable to handle kernel paging request at virtual address ffffff90e78c7964
Call trace:
qcom_vadc_scale_code_voltage_factor+0x74/0x104
qcom_vadc_scale_hw_calib_die_temp+0x20/0x60
qcom_adc5_hw_scale+0x78/0xa4
adc5_read_raw+0x3d0/0x65c
iio_channel_read+0x240/0x30c
iio_read_channel_processed+0x10c/0x150
qpnp_tm_get_temp+0xc0/0x40c
of_thermal_get_temp+0x7c/0x98
thermal_zone_get_temp+0xac/0xd8
thermal_zone_device_update+0xc0/0x38c
qpnp_tm_probe+0x624/0x81c
platform_drv_probe+0xe4/0x11c
really_probe+0x188/0x3fc
driver_probe_device+0xb8/0x188
__device_attach_driver+0x114/0x180
bus_for_each_drv+0xd8/0x118
__device_attach+0x180/0x27c
device_initial_probe+0x20/0x2c
bus_probe_device+0x78/0x124
deferred_probe_work_func+0xfc/0x138
process_one_work+0x3d8/0x8b0
process_scheduled_works+0x48/0x6c
worker_thread+0x488/0x7cc
kthread+0x24c/0x264
ret_from_fork+0x10/0x18

Unfortunately, when I went to add the initializer for this and tried to
boot it, my machine shut down immediately, complaining that it was
hotter than the sun. It appears that adc5_chans_pmic and adc5_chans_rev2
were initializing prescale_index as if it were directly a divisor,
rather than the index into adc5_prescale_ratios that it is.

Fix the uninitialized value, and change the static initialization to use
indices into adc5_prescale_ratios.
Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Add information about new compatible for S5PV210
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Make it possible to use Exynos ADC driver on S5PV210 based devices.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

S5PV210's ADC variant is almost the same as v1 except that it has 10
channels and doesn't require the pmu register
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Commit 2a54e325 ("staging: mt7621-mmc: Remove #if 0 blocks in sd.c")
does not completely remove an #if 0 block in sd.c. This causes the function
msdc_select_clksrc() which was eariler not compiled, to be compiled.
That causes an error - MSDC_CLKSRC_REG is not defined.

This patch completely removes the #if 0 block
Reported-by: NeilBrown <neil@brown.name>
Fixes: 2a54e325 ("staging: mt7621-mmc: Remove #if 0 blocks in sd.c")
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Reviewed-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

As per default the GPU memory config of the Raspberry Pi isn't sufficient
for the camera usage. Even worse the bcm2835 camera driver doesn't provide a
helpful error message in this case. So let's add a hint to point the user
to the likely cause.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently there is only a catch-all info message which print the
relevant error code without any context. So add more specific error
messages in order to narrow down possible issues.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Just like the bcm2835-video make this a platform driver which is probed
by vchiq. In order to change the number of channels use a module
parameter instead, but use the maximum as default.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

There is not much value behind this boilerplate, so use
module_platform_driver() instead.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Enable the compilation test for bcm2835-audio to gain more build coverage.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Following Eric's commit 37b7b308 ("staging/vc04_services: Register a
platform device for the camera driver.") this register the audio driver as
a platform device, too.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Since the camera driver isn't probed via DT, we need to properly setup DMA.

Fixes: 37b7b308 ("staging/vc04_services: Register a platform device for the camera driver.")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In order to have this more consistent between the vc04 services move
the module information to the end of the file.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In order to make the module bcm2835-camera load automatically, we need to
add a module alias.

Fixes: 4bebb031 ("staging/bcm2835-camera: Set ourselves up as a platform driver.")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Abort the probing of the camera driver in case there isn't a camera
actually connected to the Raspberry Pi. This solution also avoids a
NULL ptr dereference of mmal instance on driver unload.

Fixes: 7b3ad5ab ("staging: Import the BCM2835 MMAL-based V4L2 camera driver.")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The device-tree checking code sees node names  "i2c" and "spi" in the
pinctrl definition and thinks these are defining i2c or spi devices,
and complains that they look wrong.

So add a '0' to the end of each name (much like "uart" and "rgmii"
have numbers at the end) to avoid the warning.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cmd_buf is only used when MT6575_SD_DEBUG is defined.
So only declare it in that case.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

<linux/interrupt.h> is sometimes included by other include files,
and sometimes not, depending on config, particularly CONFIG_HIGHMEM.

So include it explicitly rather than relying on implicit inclusion.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This code generates a waring as PHY_GBIT_FEATURES is "long" but
->supported in "int".

It looks likely that "PHY_1000BT_FEATURES" is the correct define to
use - it is intended to be used with the ->features field.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Since commit bb276262 ("mtd: spi-nor: only apply reset hacks to
broken hardware"), we need to mark the spi-nor as "broken" for reboot
to work.
Note that nothing is actually broken here.  The hardware-watchdog in
the SoC isn't wired in a way that works, but then the board doesn't
claim to support a hardware watchdog - and the SPI certain isn't
"broken".

This causes an annoying warning on every boot, but that is better than
failing on ever reboot.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Since commit f8c55dc6 ("MIPS: use generic dma noncoherent ops for
simple noncoherent platforms") changed MIPS dma handling, the mmc
driver fails because it doesn't have a dma mask is set.

So set the correct dma mask.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Since commit f8c55dc6 ("MIPS: use generic dma noncoherent ops for
simple noncoherent platforms") changed MIPS dma handling, the eth
driver fails because the dma mask is set on the wrong 'struct device'.

Move the setting to the correct struct device.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

I had started the removal of semaphores in this driver without knowing
that Nicolas Saenz Julienne also worked on this. In case of the "remote
event" infrastructure, my solution seemed significantly better, so I'm
proposing this as a change on top.

The problem with using either semaphores or completions here is that
it's an overly complex way of waking up a thread, and it looks like the
'count' of the semaphore can easily get out of sync, even though I found
it hard to come up with a specific example.

Changing it to a 'wait_queue_head_t' instead of a completion simplifies
this by letting us wait directly on the 'event->fired' variable that is
set by the videocore.

Another simplification is passing the wait queue directly into the helper
functions instead of going through the fragile logic of recording the
offset inside of a structure as part of a shared memory variable. This
also avoids one uncached memory read and should be faster.

Note that I'm changing it back to 'killable' after the previous patch
changed 'killable' to 'interruptible', apparently based on a misunderstanding
of the subtle down_interruptible() macro override in vchiq_killable.h.

Fixes: f27e47bc ("staging: vchiq: use completions instead of semaphores")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Nothing uses the semaphores any more in this driver, so remove
all references to that type.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This semaphore is used like a mutex, so it should use the regular
mutex API, as we do in the other copies of this driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This driver uses many semaphores, most of them are equivalent to
completions. The other copies of this driver got moved over to
completions a while ago, so do the same here.

In this usage scenario, the two are equivalent, so the behavior
should not change.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

HGz -> GHz
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The function rtw_port_switch_chk() returns always false.
Remove the function and related dead code.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use Hal_GetChnlGroup88E() instead of duplicating it's code
in get_rx_power_val_by_reg().
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Zeroing the array result[m][n] and setting only the values at
even 'n's simplifies the code and slightly reduces object file
size.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Changes do_insn*_ioctl functions to allow for data lengths for each
comedi_insn of up to 2^16.  This patch also changes these functions to only
allocate as much memory as is necessary for each comedi_insn, rather than
allocating a fixed-sized scratch space.

In testing some user-space code for the new INSN_DEVICE_CONFIG_GET_ROUTES
facility with some newer hardware, I discovered that do_insn_ioctl and
do_insnlist_ioctl limited the amount of data that can be passed into the
kernel for insn's to a length of 256.  For some newer hardware, the number
of routes can be greater than 1000.  Working around the old limits (256)
would complicate the user-space/kernel interaction.

The new upper limit is reasonable with current memory available and does
not otherwise impact the memory footprint for any current or otherwise
typical configuration.
Signed-off-by: Spencer E. Olson <olsonse@umich.edu>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

As explained in previous patch, this SPI controller seems to be
tested on SPI flash only before mass production and some bits are
swizzled under other SPI modes probably due to incorrect wiring
inside the silicon. Drop implementation of SPI mode 1/2/3 since
they are broken.

Also drop RT2880_SPI_MODE_BITS macro because we now have only
SPI_LSB_FIRST implemented and the mode_bits is so short that we
don't need a macro there.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Reviewed-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

According to John Crispin (aka blogic) on IRC on Nov 26 2018:
  so basically i made cs1 work for MTK/labs when i built
  the linkit smart for them. the req-sheet said that cs1 should be proper
  duplex spi. however ....
   1) the core will always send 1 byte before any transfer, this is the
      m25p80 command.
   2) mode 3 is broken and bit reversed (?)
   3) some bit are incorrectly wired in hw for mode2/3
  we wrote a test script and test for [0-0xffff] on all modes and certain
  bits are swizzled under certain conditions and it was not possible to
  fix this even using a hack.
  we then decided to use spi-gpio and i never removed the errornous code
  basically the spi is fecked for anything but half duplex spi mode0
  running a sflash on it

The controller will always send some data from OPCODE register under half
duplex mode before starting a full-duplex transfer, so the full-duplex
mode is broken.
This piece of code also make CS1 unavailable since it forces the
broken full-duplex mode to be used on CS1.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Reviewed-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In this driver, both function the same way, but we want to eventually
kill off semaphores, so a completion is the better choice here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Changed "stoped" to "stopped".
Signed-off-by: Aaron Strahlberger <aaron.strahlberger@posteo.de>
Signed-off-by: Julius Wiedmann <julius.wiedmann@fau.de>
Signed-off-by: Dominik Huber <domi250@gmx.de>
Reviewed-by: Gao Xiang <gaoxiang25@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

It's better to use pre-calculated values to make
on-disk definition more straight-forward and human-readable.

Since there is the only one user, let's remove
__EROFS_BIT entirely.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Gao Xiang <hsiangkao@aol.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

remove all redundant BUG_ONs, and turn the rest
useful usages to DBG_BUGONs.
Signed-off-by: Gao Xiang <gaoxiang25@huawei.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

remove all redundant BUG_ONs, and turn the rest
useful usages to DBG_BUGONs.
Signed-off-by: Gao Xiang <gaoxiang25@huawei.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently, we're using the devm version of some but not all functions.
Switch to the devm version of iio_triggered_buffer_setup and
iio_device_register to simplify the code a bit and decrease the chance of
bugs.
Signed-off-by: Martin Kelly <martin@martingkelly.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>