The aliases are board-specific and shouldn't be included in the common
SoC dtsi. Move them over to the boards.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The failsafe partitions for the DP firmware and for AT-F are unused. If
AT-F will ever be supported in the failsafe mode, then it will be a FIT
image. Thus fold the unused partitions into the failsafe bootloader one
to have enough storage if the bootloader image will grow.

While at it, remove the reserved partition. It served no purpose other
than having no hole in the map.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Move the MTD partitions to the partitions subnode. This is the new way
to specify the partitions, see
  Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

According to the datasheet RTL8211, it must be asserted low for at least
10ms and at least 72ms "for internal circuits settling time" before
accessing the PHY registers.

Add properties to describe such requirements.
Reported-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Commit 99e71c02 ("arm64: dts: imx8mq-librem5: Don't mark buck3 as always on")
removed always-on marking from GPU regulator, which is great for power
saving - however it introduces additional i2c0 traffic which can be deadly
for devices from the Dogwood batch.

To workaround the i2c0 shutdown issue on Dogwood, this commit marks
buck3 as always-on again - but only for Dogwood (r3).
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

There was an additional alias in the specifier it hogged line 27
instead of line 1.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add 2x2 SFP+ cage support for clearfog-itx boards.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

With the first redesign the debug UART had changed from
UART2 to UART1.
As the first hardware revision is considered as alpha and
will not be supported in future. The old setup will not
be preserved.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Reorder flexspi clock-names entry to make it compliant with bindings.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Reorder flexspi clock-names entry to make it compliant with bindings.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

In NXP LS1028A there is a MAC-to-MAC internal link between enetc_port2
and mscc_felix_port4. This link operates at 2.5Gbps and is described as
such for the mscc_felix_port4 node.

The reason for the discrepancy is a limitation in the PHY library
support for fixed-link nodes. Due to the fact that the PHY library
registers a software PHY which emulates the clause 22 register map, the
drivers/net/phy/fixed_phy.c driver only supports speeds up to 1Gbps.

The mscc_felix_port4 node is probed by DSA, which does not use the PHY
library directly, but phylink, and phylink has a different representation
for fixed-link nodes, one that does not have the limitation of not being
able to represent speeds > 1Gbps.

Since the enetc driver was converted to phylink too as of commit
71b77a7a ("enetc: Migrate to PHYLINK and PCS_LYNX"), the limitation
has been practically lifted there too, and we can describe the real link
speed in the device tree now.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add the description for ecspi2 support.
Signed-off-by: Adrien Grassein <adrien.grassein@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The i.MX8QuadMax is a Dual (2x) Cortex-A72 and Quad (4x) Cortex-A53
proccessor with powerful graphic and multimedia features.
This patch adds i.MX8QuadMax MEK board support.

Note that MX8QM needs a special workaround for TLB flush due to a SoC
errata, otherwise there may be random crash if enable both clusters of
A72 and A53. As the errata workaround is still not in mainline, so we
disable A72 cluster first for MX8QM MEK.

Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The i.MX8QuadMax is a Dual (2x) Cortex-A72 and Quad (4x) Cortex-A53
proccessor with powerful graphic and multimedia features. It uses
the same architecture as MX8QXP, so many SS can be reused.
This patch adds i.MX8QuadMax SoC dtsi file.

Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The DMA SS of MX8QM is mostly the same as the DMA part in MX8QXP ADMA SS
while it has one more instance for each of LPUART, ADC and LPI2C. And unlike
MX8QXP that flexcan clocks are shared between multiple CAN instances,
MX8QM has separate flexcan clock slice.

So we reuse the most part of common imx8-ss-dma.dtsi and add new things
based on it.

Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

amda ss is consisted of dma and audio ss in qxp which are
also used in qm.
Let's split them into two ss for better code reuse.
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The CONN SS of MX8QM is mostly the same as MX8QXP except it has one more
USB HSIC module support. So we can fully reuse the exist CONN SS dtsi.
Add <soc>-ss-conn.dtsi with compatible string updated according to
imx8-ss-conn.dtsi.

Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The LSIO SS of MX8QM is exactly the same as MX8QXP. So we can fully
reuse the exist LSIO SS dtsi. Add <soc>-ss-lsio.dtsi with compatible
string updated according to imx8-ss-lsio.dtsi.

Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

switch to new lpcg clock binding
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

switch to two cell scu clock binding
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add adma lpcg clocks

Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add conn lpcg clocks

Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add lsio lpcg clocks

Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

MX8 SoC is comprised of a few HW subsystems while some of them can be
reused in the different SoCs. So let's re-orginize them into subsystems
in device tree as well for the possible reuse of the common part.

Note, as there's still no devices of hsio subsys, so removed it
first instead of creating a subsys headfile with no devices.
They will be added back when new devices added.

Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

SCU clock depends on SCU Power domain. Moving scu pd node before
scu clock can save a hundred of defer probes of all system devices
which depends on power domain and clocks.

Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

According to binding doc, add the fallback compatible string for
scu pd.

Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

There is wdog[2,3] in i.MX8MP, so add them.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The Kontron pitx-imx8m board is based on an i.MX8MQ soc.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The board has both MACs routed out, enable the EQOS.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dong Aisheng <aisheng.dong@nxp.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add EQOS GMAC node per Documentation/devicetree/bindings/net/imx-dwmac.txt ,
leave out the nvmem entries as that is not yet available, so the MAC has to
be passed in via DT by the bootloader.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dong Aisheng <aisheng.dong@nxp.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Engicam EDIMM2.2 Starter Kit is an EDIMM 2.2 Form Factor Capacitive
Evaluation Board.

Genaral features:
- LCD 7" C.Touch
- microSD slot
- Ethernet 1Gb
- Wifi/BT
- 2x LVDS Full HD interfaces
- 3x USB 2.0
- 1x USB 3.0
- HDMI Out
- Mini PCIe
- MIPI CSI
- 2x CAN
- Audio Out

i.Core MX8M Mini is an EDIMM SoM based on NXP i.MX8M Mini from Engicam.

i.Core MX8M Mini needs to mount on top of this Evaluation board for
creating complete i.Core MX8M Mini EDIMM2.2 Starter Kit.

PCIe, DSI, CSI nodes will add it into imx8mm-engicam-edimm2.2.dtsi once
Mainline Linux supported.

Add support for it.
Signed-off-by: Matteo Lisi <matteo.lisi@engicam.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Engicam C.TOUCH 2.0 is an EDIMM compliant general purpose Carrier
board.

Genaral features:
- Ethernet 10/100
- Wifi/BT
- USB Type A/OTG
- Audio Out
- CAN
- LVDS panel connector

i.Core MX8M Mini is an EDIMM SoM based on NXP i.MX8M Mini from Engicam.

i.Core MX8M Mini needs to mount on top of this Carrier board for
creating complete i.Core MX8M Mini C.TOUCH 2.0 board.

Add support for it.
Signed-off-by: Matteo Lisi <matteo.lisi@engicam.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

i.Core MX8M Mini is an EDIMM SoM based on NXP i.MX8M Mini
from Engicam.

General features:
- NXP i.MX8M Mini
- Up to 2GB LDDR4
- 8/16GB eMMC
- Gigabit Ethernet
- USB 2.0 Host/OTG
- PCIe Gen2 interface
- I2S
- MIPI DSI to LVDS
- rest of i.MX8M Mini features

i.Core MX8M Mini needs to mount on top of Engicam baseboards
for creating complete platform solutions.

Add support for it.
Signed-off-by: Matteo Lisi <matteo.lisi@engicam.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Per dt-bindings, the clock-names sequence should be ipg ahb per to pass
dtbs_check.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add audio description and pin muxing.
Signed-off-by: Adrien Grassein <adrien.grassein@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add FlexSPI description an pin muxing.
Signed-off-by: Adrien Grassein <adrien.grassein@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add description for the four PWMs.
Signed-off-by: Adrien Grassein <adrien.grassein@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Remove useless clocks in UART 2
Signed-off-by: Adrien Grassein <adrien.grassein@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add description and pin muxing for UARTs.
Signed-off-by: Adrien Grassein <adrien.grassein@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add description of USB.
usbotg2 seems to not working on all boards (including ones
from variscite).
Signed-off-by: Adrien Grassein <adrien.grassein@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>