This is in preparation for restoring saved tuning parameters
when resuming the TMIO driver.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add support for r7s72100 SoC.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

For the r7s72100 SOC, the DATA_PORT register was changed to 32-bits wide.
Therefore a new flag has been created that will allow 32-bit reads/writes
to the DATA_PORT register instead of 16-bit (because 16-bits accesses are
not supported).
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

In moving platforms from board files to DT, there still needs to be a way
to set the ocr_mask setting for the tmio driver during probe. Without this
setting, the probe will fail because the supported voltages are not known.

This patch will also traditional platform registration platforms to
migrate to DT.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

There were several instances of code using the
enum mmc_blk_status by arbitrarily converting it to an int and
throwing it around to different functions. This makes the code
hard to understand to may give rise to strange errors.

Especially the function prototype mmc_start_req() had to be
modified to take a pointer to an enum mmc_blk_status and the
function pointer .err_check() inside struct mmc_async_req
needed to return an enum mmc_blk_status.

In every case: instead of assigning the block layer error code
to an int, use the enum, also change the signature of all
functions actually passing this enum to use the enum.

To make it possible to use the enum everywhere applicable, move
it to <linux/mmc/core.h> so that all code actually using it can
also see it.

An interesting case was encountered in the MMC test code which
did not return a enum mmc_blk_status at all in the .err_check
function supposed to check whether asynchronous requests worked
or not: instead it returned a normal -ERROR or even the test
frameworks internal error codes.

The test code would also pass on enum mmc_blk_status codes as
error codes inside the test code instead of converting them
to the local RESULT_* codes.

I have tried to fix all instances properly and run some tests
on the result.

Cc: Chunyan Zhang <zhang.chunyan@linaro.org>
Cc: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The ecc_err flag is only assigned 0 or 1 and treated as a bool,
so convert it to a bool.

Cc: Chunyan Zhang <zhang.chunyan@linaro.org>
Cc: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

This gen_err flag is only assigned 0 or 1 and treated as a bool,
so convert it to a bool.

Cc: Chunyan Zhang <zhang.chunyan@linaro.org>
Cc: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The sdhci capabilities register can be incorrect. The sdhci-caps-mask
and sdhci-caps dt properties specify which bits of the register are
incorrect and what their values should be. This patch makes the sdhci
driver use those properties to correct the caps during
__sdhci_read_caps.

During __sdhci_read_caps
Use the sdhci-caps-mask property to turn off the incorrect bits of the
sdhci register after reading them.
Use the sdhci-caps to turn on bits after using sdhci-caps-mask to turn
off the incorrect ones.
Signed-off-by: Zach Brown <zach.brown@ni.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

On some systems the sdhci capabilty register is incorrect for one
reason or another.

The sdhci-caps-mask property specifies which bits in the register
are incorrect and should be turned off before using sdhci-caps to turn
on bits.

The sdhci-caps property specifies which bits should be turned on.
Signed-off-by: Zach Brown <zach.brown@ni.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The ST Micro-specific busy detection was made after the assumption
that only this variant supports busy detection. So when doing busy
detection, the host immediately tries to use some ST-specific
register bits.

Since the qualcomm variant also supports some busy detection
schemes, encapsulate the variant flags better in the variant struct
and prepare to add more variants by just providing some bitmasks
to the logic.

Put the entire busy detection logic within an if()-clause in the
mmci_cmd_irq() function so the code is only executed when busy
detection is enabled, and so that it is kept in (almost) one
place, and add comments describing what is going on so the
code can be understood.

Tested on the Ux500 by introducing some prints in the busy
detection path and noticing how the IRQ is enabled, used and
disabled successfully.

Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

There was some confusion in the CPSM (Command Path State Machine)
and DPSM (Data Path State Machine) regarding the naming of the
registers, clarify the meaning of this acronym so the naming is
understandable, and consistently use BIT() to define these fields.

Consequently name the register bit defines MCI_[C|D]PSM_* and
adjust the driver as well.

Include new definitions for a few bits found in a patch from
Srinivas Kandagatla.

Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Support for DMA slave map has been added to the s3c24xx-dma
controller in commit 34681d84
"dmaengine: s3c24xx: Add dma_slave_map for s3c2440 devices"
This patch converts the s3cmci driver to also use it, so we can
eventually get rid of the exported filter function once all
related DMA clients are updated.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The MMC_CAP2_NO_PRESCAN_POWERUP was invented to avoid running the power up
sequence, mmc_power_up(), during ->probe() of the mmc host driver, but
instead defer this to the mmc detect work. This is especially useful for
those hosts that suffers from a long initialization time, as this time
would otherwise add up to the total boot time.

However, due to the introduction of runtime PM of mmc host devices in the
mmc core, this behaviour changed a bit. More precisely, it caused the mmc
core to runtime resume the host device during ->probe() of the host driver.
In cases like the rtsx_usb_sdmmc, runtime resuming the device may be costly
and thus affecting the total boot time.

To improve this behaviour when using MMC_CAP2_NO_PRESCAN_POWERUP, let's
postpone also calling mmc_power_off() when starting the host. This change
allows the mmc core to avoid runtime resuming the device, as it don't need
to claim the host for that execution path.

Cc: Ritesh Raj Sarraf <rrs@researchut.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Initial support for the SD/eMMC controller in the Amlogic S905/GX*
family of SoCs.
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Now there are no variant drivers using dw_mci_suspend
and dw_mci_resume, so let's remove it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Let's migrate it to use runtime PM and remove the system
PM callback from this driver. With this patch, it could
handle system PM properly and could also use runtime PM
if we enable it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Let's migrate it to use runtime PM and remove the system
PM callback from this driver. With this patch, it could
handle system PM properly and could also use runtime PM
if we enable it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Let's migrate it to use runtime PM and remove the system
PM callback from this driver. With this patch, it could
handle system PM properly and could also use runtime PM
if we enable it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Let's migrate it to use runtime PM and remove the system
PM callback from this driver. With this patch, it could
handle system PM properly and could also use runtime PM
if we enable it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

We could disable biu clk if gpio card detect available,
or it is a non-removable device.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add new helper API mmc_can_gpio_cd for slot-gpio to make
host drivers know whether it supports gpio card detect.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

This patch adds runtime PM support for dw_mmc-rockchip.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

This patch add dw_mci_runtime_suspend/resume interfaces
and expose it to dw_mci variant driver to support runtime
PM.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

When polling for busy after sending a MMC_SWITCH command, both the optional
->card_busy() callback and CMD13 are being used in conjunction.

This doesn't make sense. Instead it's more reasonable to rely solely on the
->card_busy() callback when it exists. Let's change that and instead use
the CMD13 as a fall-back. In this way we avoid sending CMD13, unless it's
really needed.

Within this context, let's also take the opportunity to make some
additional clean-ups and clarifications to the related code.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>

In yet another step of cleaning up __mmc_switch(), let's factor out the
code that deals with card busy polling.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>

The __mmc_switch() deserves a clean-up. In this step, let's move some code
outside of the do-while loop, which deal deals with the card busy polling.

This change simplifies the code in that sense that it becomes easier to follow
what is being executed during card busy polling, but it also gives a better
understanding for when polling isn't done.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>

Following changes needs mmc_switch_status() to be available both from mmc.c
and mmc_ops.c. Allow that by moving its implementation to mmc_ops.c and
make it available via mmc_ops.h.

Moving mmc_switch_status() to mmc_ops.c, also enables us to turn
mmc_switch_status_error() into static function. So let's take the
opportunity to change this as well.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>

Provides runtime PM callbacks to enable and disable clock resources
when idle. Also support system PM callbacks to be called during system
suspend and resume.
Reviewed-by: Ritesh Harjani <riteshh@codeaurora.org>
Reviewed-by: Georgi Djakov <georgi.djakov@linaro.org>
Tested-by: Ritesh Harjani <riteshh@codeaurora.org>
Signed-off-by: Pramod Gurav <pramod.gurav@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

VMMC is an optional regulator, which means that mmc_regulator_get_supply
will only return an error in case of a deferred probe, but not when the
regulator is not set in the DT.

However, the sunxi driver assumes that VMMC is always there, and doesn't
check the value of the regulator pointer before using it, which obviously
leads to a (close to) null pointer dereference.

Add proper checks to prevent that.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

It is used for limitation of buffer size during IOCTL such as FFU.
However, eMMC FW size is bigger than (512L*256).
(For instance, currently, Samsung eMMC FW size is over 300KB.)
So, it needs to increase to execute FFU.
Signed-off-by: Jeonghan Kim <jh4u.kim@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.

Export the module alias information using the MODULE_DEVICE_TABLE() macro.

Before this patch:

$ modinfo drivers/mmc/host/sdhci-of-at91.ko | grep alias
$

After this patch:

$ modinfo drivers/mmc/host/sdhci-of-at91.ko | grep alias
alias:          of:N*T*Catmel,sama5d2-sdhciC*
alias:          of:N*T*Catmel,sama5d2-sdhci
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.

Export the module alias information using the MODULE_DEVICE_TABLE() macro.

Before this patch:

$ modinfo drivers/mmc/host/mtk-sd.ko | grep alias
$

After this patch:

$ modinfo drivers/mmc/host/mtk-sd.ko | grep alias
alias:          of:N*T*Cmediatek,mt8135-mmcC*
alias:          of:N*T*Cmediatek,mt8135-mmc
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Enable runtime PM autosuspend for the rtsx_usb_sdmmc driver to avoid the
device being runtime suspended and runtime resumed between each request.
Let's use a default timeout of 50ms, to be consistent with other mmc hosts.

Cc: Ritesh Raj Sarraf <rrs@researchut.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

value of ios->timing is not related with SDCHI v3.0.  If Controller version
is v3.0, SDHCI_QUIRK_NO_HISPD_BIT is meaningless.  To prevent the setting
wrong bit moves into one condition checking.  (e.g sdhci-s3c doesn't use
SDHCI_CTRL_HISPD bit, instead using this bit as other purpose.)
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Pull IOMMU fixes from David Woodhouse:
 "Two minor fixes.

  The first fixes the assignment of SR-IOV virtual functions to the
  correct IOMMU unit, and the second fixes the excessively large (and
  physically contiguous) PASID tables used with SVM"

* git://git.infradead.org/intel-iommu:
  iommu/vt-d: Fix PASID table allocation
  iommu/vt-d: Fix IOMMU lookup for SR-IOV Virtual Functions

Pull MIPS fixes from Ralf Baechle:
 "Another round of MIPS fixes for 4.9:

   - Fix unreadable output in __do_page_fault due to the KERN_CONT
     patchset

   - Correctly handle MIPS R6 fixes to the c0_wired register"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: mm: Fix output of __do_page_fault
  MIPS: Mask out limit field when calculating wired entry count

Pull vfs splice fix from Al Viro.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  fix default_file_splice_read()

Botched calculation of number of pages.  As the result,
we were dropping pieces when doing splice to pipe from
e.g. 9p.
Reported-by: Alexei Starovoitov <ast@kernel.org>
Tested-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>