Move the station state modification right before insert,
this just makes the current code more readable (you can
tell that it's before insertion looking at a single
screenful of code) right now, but some upcoming changes
will require this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Added a check on the direct register access.
Checks that the address is in the lower ragnge (0x0-0x2000),
which belongs to CSR, HBUS and FH registers.
Signed-off-by: Amit Beka <amit.beka@intel.com>
Signed-off-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com>

smatch correctly complains:
iwl-trans-pcie.c +1528 iwl_trans_pcie_start_hw(50) warn: 'trans->irq' was not released on error

Fix it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com>

The routines dealing with the ucode are spread through several files.
Move them all to the same file and create a iwl-ucode.h file with the
ucode file definitions.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

There is nothing device specific in the initialization of the
bcast_sta_id so move it to the common inititalization routine.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

change a comment to be a little more clear
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

The message was misleading when a queue is deactivated. The fifo
number is irrelevant then, so don't print it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

This trans_ops->stop_hw leaves the RFKILL interrupt enabled,
we can call that one instead of enable_rfkill_int. By that,
we reduce the numbers of acceesses to the NIC from the upper
layers.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

The HW revision is now read by the transport layer in its allocation.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

Get this information from the transport layer.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

Get this information from the transport layer.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

Get this information from the transport layer which is now in charge
of the APM too.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

This handler was called from the transport layer only. Merge it
to the transport's apm_init.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

Now there is only one transport function that launch a specific fw:
trans_ops->start_fw. This one replaces trans_ops->start_device and
trans_ops->kick_nic. The code that actually loads the fw to the
device has been moved to the transport specific code.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

This is another clean up of the proble flow.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

This handler stops the HW and puts it in low power state.
It will allow to clean up the flows in the upper layers.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

This is transport related
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

Kill the trans_ops->prepare_card_hw which is now useless.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

This handler will become thicker, reflect its real role now.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

This is transport related
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

From now on, the transport layer in charge of providing access to the
device. So change all the driver to give a pointer to the transport
to all the low level functions that actually access the device.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

Most of the accesses to the registers are done from the transport layer.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

All the bus configuration is now done in the transport
allocation fucntion.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

Change the way we alloc the transport on the way.
Since the transport is allocated from a bus specific area, we can
give the bus specific parameters (i.e. pci_dev for PCI) to the
transport. This will be useful when the bus layer will be killed.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

Allocating the shrd area dynamically will allow more agility
while revamping the flows.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

There is no link between the two. Ensure that the NIC is on outside
the code of the EEPROM handling.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

This patch connects IDI transport to driver. It does so
by using a number of ifdefs at this stage.
IDI is a new transport that is under development.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

Define a new handler in the transport layer API: fw_alive.
Move iwl_reset_ict to this new handler, and move the content
of tx_start to this handler.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into wireless-next

ath6kl: initialize the 'nominal_phy' field in the 'wmi_create_pstream_cmd' struct for create_qos command

The nominal_phy field is uninitialized. Initialize it to min_phy_rate for
create_qos.

kvalo: simplified the equation as checkpatch complained for a too long line
Signed-off-by: Chilam Ng <chilamng@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Both Luis and John reported that they see a compiler warning:

drivers/net/wireless/ath/ath6kl/init.c: In function 'ath6kl_init_hw_params':
drivers/net/wireless/ath/ath6kl/init.c:1377:26: warning: ‘hw’
may be used uninitialized in this function

Oddly enough I have never seen it. But AFAICT the code is correct and
hw is not used uninitalized so add uninitialized_var() to inform that to
the compiler.
Reported-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Reported-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Correct spelling "spported" to "supported" in
drivers/net/wireless/ath/ath6kl/cfg80211.c
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Set the host pm flag MMC_PM_WAKE_SDIO_IRQ to allow host
to disable the sdc2_clk and sdc2_h_clk,so that the MSM device
enter into TCXO shutdown.
Signed-off-by: Santosh Sajjan <ssajjan@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This patch addresses a kernel bugzilla report and two recent mail threads.

The kernel bugzilla report is https://bugzilla.kernel.org/show_bug.cgi?id=42632,
which reports a udev timeout on boot.

The first mail thread, which was on LKML (http://lkml.indiana.edu/hypermail/
linux/kernel/1112.3/00965.html) was for a WARNING that occurs after a
suspend/resume cycle for rtl8192cu.

The scond mail thread (http://marc.info/?l=linux-wireless&m=132655490826766&w=2)
concerned changes in udev that break drivers that delay while firmware is loaded
on modprobe.

This patch converts all rtlwifi-based drivers to use the asynchronous firmware
loading mechanism. Drivers rtl8192ce, rtl8192cu and rtl8192de share a common
callback routine. Driver rtl8192se needs different handling of the firmware,
thus it has its own code.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

channelFlags doesn't contain the operating HT mode.
Use IS_CHAN_HT40 to determine if the current channel is
in HT40 mode.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch modifies ath9k_htc to load the needed
firmware in an asynchronous manner, fixing timeouts
that were introduced with the new udev changes.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>