Pass device pointer instead of device name as parameter to iio_channel_get_all
and iio_channel_get_all_cb. This will enable us to use OF information to
retrieve consumer channel information.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

For chips with more than 8 bit ADC resolution, received data was always
masked against 0xfff, ie with a 12 bit mask. This can result in bad data
for chips with 10 bit resolution if those chips have higher bits set
(seen with MAX1139).

The receive buffer was defined as char array. This could result in
unintentional sign extensions if the upper bit in a received byte
was set. Since the chip is configured for unipolar mode, we never
have to handle negative values, and sign extensions are never needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Add 'iio-hwmon' OF compatibility table entry to enable OF matches.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

The 'name' attribute is mandatory for hwmon devices.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

This patch remove st_sensors_get_sampling_frequency_avl and
st_sensors_get_scale_avl functions used only in
st_sensors_sysfs_sampling_frequency_avail and st_sensors_sysfs_scale_avail
sysfs functions.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

This patch adds support for the InvenSense itg3200.
The itg3200 is a three-axis gyro with 16-bit ADC and
I2C interface.
Signed-off-by: Manuel Stahl <manuel.stahl@iis.fraunhofer.de>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

The adxrs450 is in a reasonable shape now. It follows the IIO ABI and non of the
standard code checker tools report any issue, so move it out of staging.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

The contents of the adxrs450 header file is not used outside the main drivers
file, so just move the contents from the header file into the drivers main file.
Also rename the adxrs450 driver file from adxrs450_core.c to adxrs450.c.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Fix the name of the iio_device parameter for a few functions and add
documentation for one missing function parameter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

The adxrs450 requires a delay of at least 0.1 ms between register writes.  Using
msleep() for such small delays is not recommended. So use usleep_range instead.

Fixes the following checkpatch warning:
	WARNING: msleep < 20ms can sleep for up to 20ms; see Documentation/timers/timers-howto.txt
	+	msleep(1);
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

This is one of the exceptions to the 80 chars per line rule since breaking the
string in half it badly affects the grep-ability.

Fixes the following checkpatch warning:
	WARNING: quoted string split across lines
	#203: FILE: staging/iio/gyro/adxrs450_core.c:203:
		+		dev_warn(&st->us->dev, "The initial power on response "
		+			 "is not correct! Restart without reset?\n");
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Reflow two lines to meet the 80 characters per line limit.

Fixes the following checkpatch warnings:
	WARNING: line over 80 characters
	#29: FILE: staging/iio/gyro/adxrs450_core.c:29:
	+ * @reg_address: the address of the lower of the two registers,which should be an even address,

	WARNING: line over 80 characters
	#81: FILE: staging/iio/gyro/adxrs450_core.c:81:
	+ * @reg_address: the address of the lower of the two registers,which should be an even address,
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Don't spam the bootlog with the devices part id and serial number.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Instead of silently discarding the upper bits reject out of range values for the
calibscale property.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

The calibbias (DNC) register contains a 10-bit twos complement value. Perform a
proper sign extension when reading the register, otherwise negative will
incorrectly be displayed as large positive values.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Fixes the following sparse warnings:

	drivers/staging/iio/gyro/adxrs450_core.c:46:15: warning: cast to restricted __be32
	drivers/staging/iio/gyro/adxrs450_core.c:62:17: warning: cast to restricted __be32
	drivers/staging/iio/gyro/adxrs450_core.c:89:15: warning: cast to restricted __be32
	drivers/staging/iio/gyro/adxrs450_core.c:129:17: warning: cast to restricted __be32
	drivers/staging/iio/gyro/adxrs450_core.c:168:16: warning: cast to restricted __be32
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

This partially reverts commit cb449687. There is
no apparent reason why we should split a transaction which consists out of
multiple transfers into multiple transactions each having one transfer. While
this works it introduces a bunch of unnecessary context switch and additional
setup costs.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

__iio_update_buffer updates the buffer's bytes_per_datum and length fields.
But the only user of this function just passes in these exact fields, so the
call basically looks like this:

	buffer->bytes_per_datum = buffer->bytes_per_datum;
	buffer->length = buffer->length;

Which means it is a noop and can be removed. Also remove the function itself,
since it is now unused.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

This patch adds a generic magnetometer driver for STMicroelectronics
magnetometers, currently it supports:
LSM303DLHC, LSM303DLM, LIS3MDL.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

This patch adds a generic gyroscope driver for STMicroelectronics
gyroscopes, currently it supports:
L3G4200D, LSM330DL, L3GD20, L3GD20H, LSM330DLC, L3G4IS, LSM330.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

This patch adds a generic accelerometer driver for STMicroelectronics
accelerometers, currently it supports:
LSM303DLH, LSM303DLHC, LIS3DH, LSM330D, LSM330DL, LSM330DLC,
LIS331DLH, LSM303DL, LSM303DLM, LSM330.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

This patch add a generic library for STMicroelectronics 3-axis sensors.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

These functions are only used by the comedi core. Move the
prototypes to comedi_internal.h so they are not exposed to
the comedi drivers.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

These functions are only used by the comedi core. Move the
prototypes to comedi_internal.h so they are not exposed to
the comedi drivers.

Tidy up comedi_internal.h a bit so that all the internal stuff
in drivers.c is grouped.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Group all the general comedi driver register/config/attach
prototypes into one place in comedidev.h.

Reorder the functions in drivers.c a bit so they are in a more
logical usage order (bottom to top).
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Convert this pcmcia driver to the comedi auto attach mechanism.

This allows getting rid of the "hack" needed to pass the pcmcia_device
pointer from the pcmcia_driver to the comedi_driver.

We can also get rid of the boardinfo since it was only used to
provide the "name" that was used with the manual attach.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Convert this pcmcia driver to the comedi auto attach mechanism.

This allows getting rid of the "hack" needed to pass the pcmcia_device
pointer from the pcmcia_driver to the comedi_driver.

We still need the boardinfo because the das08 driver uses it. But we
can get rid of the duplicate that allowed attaching with the driver
name.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Convert this pcmcia driver to the comedi auto attach mechanism.

This allows getting rid of the "hack" needed to pass the pcmcia_device
pointer from the pcmcia_driver to the comedi_driver.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Introduce some helper functions to allow converting the comedi
pcmcia drivers to the comedi auto_attach mechanism.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Separate the comedi_pcmcia_* functions out of drivers.c into a new
source file, comedi_pcmcia.c. This allows conditionally building
support for comedi pcmcia drivers into the comedi core without the
need for the #if'defery. Fix the Kconfig and Makefile appropriately.

Group all the comedi_pcmcia_* prototypes into one place in comedidev.h.
Protect these prototypes with an #ifdef so that building a comedi
pcmcia driver without PCMCIA support will cause a build error. This
will normally not happen as long as the comedi pcmcia driver is placed
in the proper group in the Kconfig.

Remove the #include <pcmcia/*.h> from drivers.c. These includes are only
needed by the comedi pcmcia driver support code and the pcmcia drivers.
The include should occur in those files.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Separate the comedi_pci_* functions out of drivers.c into a new
source file, comedi_pci.c. This allows conditionally building
support for comedi PCI drivers into the comedi core. Fix the
Kconfig and Makefile appropriately.

Group all the comedi_pci_* prototypes and related defines into one
place in comedidev.h. Protect these prototypes with an #ifdef and
provide some dummy functions so that the mixed ISA/PCI comedi
drivers will still build correctly.

Remove the #include <linux/pci.h> from comedidev.h and drivers.c. This
include is only needed by the comedi PCI driver support code and the
PCI drivers. The include should occur in those files.

Also, remove the #include <linux/pci.h> from a couple non-PCI drivers
since it's not needed.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Separate the comedi_usb_* functions out of drivers.c into a new
source file, comedi_usb.c. This allows conditionally building
support for comedi USB drivers into the comedi core without the
need for the #if'defery. Fix the Kconfig and Makefile appropriately.
For aesthetic reasons, add some whitespace to the Makefile to keep
everything lined up.

Group all the comedi_usb_* prototypes into one place in comedidev.h.
Protect these prototypes with an #ifdef so that building a comedi
usb driver without USB support will cause a build error. This will
normally not happen as long as the comedi USB driver is placed in
the proper group in the Kconfig.

Remove the #include<linux/usb.h> from comedidev.h and drivers.c. This
include is only needed by the comedi USB driver support code and the
USB drivers. The include should occur in those files.

Removing the include of usb.h exposed a couple drivers that need
<linux/interrupt.h> and <linux/sched.h>. Add the missing includes.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This error happens because PIPEnsControlOut and PIPEnsControlIn unlock the
spin lock for delay, letting in another thread.

The patch moves the current MP_SET_FLAG to before filling
of sUsbCtlRequest for pControlURB and clears it in event of failing.

Any thread calling either function while fMP_CONTROL_READS or fMP_CONTROL_WRITES
flags set will return STATUS_FAILURE.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Cc: stable@vger.kernel.org # 3.8
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix:
drivers/staging/fwserial/fwserial.c:581:3: warning: format '%ld' expects argument of type 'long int', but argument 4 has type 'size_t'
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fixes these sparse warnings:
drivers/staging/fwserial/fwserial.c:430:16: sparse: incompatible types in comparison expression (different address spaces)
drivers/staging/fwserial/fwserial.c:699:30: sparse: incompatible types in comparison expression (different address spaces)
drivers/staging/fwserial/fwserial.c:802:16: sparse: incompatible types in comparison expression (different address spaces)
drivers/staging/fwserial/fwserial.c:898:16: sparse: incompatible types in comparison expression (different address spaces)
drivers/staging/fwserial/fwserial.c:1842:14: sparse: incompatible types in comparison expression (different address spaces)
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

zs_create_pool() currently takes a name argument which is
never used in any useful way.

This patch removes it.
Signed-off-by: Seth Jennings <sjenning@linux.vnet.ibm.com>
Acked-by: Nitin Gupta <ngupta@vflare.org>
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>