- 14 Jul, 2020 4 commits
-
-
Bryan O'Donoghue authored
BugLink: https://bugs.launchpad.net/bugs/1885932 [ Upstream commit f47ab3c2 ] During the process of debugging a processor derived from the msm8916 which we found the new processor was not starting one of its PLLs. After tracing the addresses and writes that downstream was doing and comparing to upstream it became obvious that we were writing to a different register location than downstream when trying to configure the PLL. This error is also present in upstream msm8916. As an example clk-pll.c::clk_pll_recalc_rate wants to write to pll->config_reg updating the bit-field POST_DIV_RATIO. That bit-field is defined in PLL_USER_CTL not in PLL_CONFIG_CTL. Taking the BIMC PLL as an example lm80-p0436-13_c_qc_snapdragon_410_processor_hrd.pdf 0x01823010 GCC_BIMC_PLL_USER_CTL 0x01823014 GCC_BIMC_PLL_CONFIG_CTL This pattern is repeated for gpll0, gpll1, gpll2 and bimc_pll. This error is likely not apparent since the bootloader will already have initialized these PLLs. This patch corrects the location of config_reg from PLL_CONFIG_CTL to PLL_USER_CTL for all relevant PLLs on msm8916. Fixes commit 3966fab8 ("clk: qcom: Add MSM8916 Global Clock Controller support") Cc: Georgi Djakov <georgi.djakov@linaro.org> Cc: Andy Gross <agross@kernel.org> Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Michael Turquette <mturquette@baylibre.com> Cc: Stephen Boyd <sboyd@kernel.org> Signed-off-by:
Bryan O'Donoghue <bryan.odonoghue@linaro.org> Link: https://lkml.kernel.org/r/20200329124116.4185447-1-bryan.odonoghue@linaro.orgSigned-off-by:
Stephen Boyd <sboyd@kernel.org> Signed-off-by:
Sasha Levin <sashal@kernel.org> Signed-off-by:
Kamal Mostafa <kamal@canonical.com> Signed-off-by:
Kelsey Skunberg <kelsey.skunberg@canonical.com>
-
Adam Honse authored
BugLink: https://bugs.launchpad.net/bugs/1885932 [ Upstream commit f27237c1 ] The AMD X370 and other AM4 chipsets (A/B/X 3/4/5 parts) and Threadripper equivalents have a secondary SMBus controller at I/O port address 0x0B20. This bus is used by several manufacturers to control motherboard RGB lighting via embedded controllers. I have been using this bus in my OpenRGB project to control the Aura RGB on many motherboards and ASRock also uses this bus for their Polychrome RGB controller. I am not aware of any CZ-compatible platforms which do not have the second SMBus channel. All of AMD's AM4- and Threadripper- series chipsets that OpenRGB users have tested appear to have this secondary bus. I also noticed this secondary bus is present on older AMD platforms including my FM1 home server. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=202587Signed-off-by:
Adam Honse <calcprogrammer1@gmail.com> Reviewed-by:
Jean Delvare <jdelvare@suse.de> Reviewed-by:
Sebastian Reichel <sebastian.reichel@collabora.com> Tested-by:
Wolfram Sang <wsa@the-dreams.de> Signed-off-by:
-
Rikard Falkeborn authored
BugLink: https://bugs.launchpad.net/bugs/1885932 [ Upstream commit ee25d974 ] round_down() can only round to powers of 2. If round_down() is asked to round to something that is not a power of 2, incorrect results are produced. The incorrect results can be both too large and too small. Instead, use rounddown() which can round to any number. Fixes: 6a721db1 ("clk: sunxi: Add A31 clocks support") Signed-off-by:
Rikard Falkeborn <rikard.falkeborn@gmail.com> Signed-off-by:
Maxime Ripard <maxime@cerno.tech> Signed-off-by:
-
Dmitry V. Levin authored
BugLink: https://bugs.launchpad.net/bugs/1885932 commit b3583fca upstream. If both the tracer and the tracee are compat processes, and gprs[2] is assigned a value by __poke_user_compat, then the higher 32 bits of gprs[2] are cleared, IS_ERR_VALUE() always returns false, and syscall_get_error() always returns 0. Fix the implementation by sign-extending the value for compat processes the same way as x86 implementation does. The bug was exposed to user space by commit 201766a2 ("ptrace: add PTRACE_GET_SYSCALL_INFO request") and detected by strace test suite. This change fixes strace syscall tampering on s390. Link: https://lkml.kernel.org/r/20200602180051.GA2427@altlinux.org Fixes: 753c4dd6 ("[S390] ptrace changes") Cc: Elvira Khabirova <lineprinter@altlinux.org> Cc: stable@vger.kernel.org # v2.6.28+ Signed-off-by:
Dmitry V. Levin <ldv@altlinux.org> Signed-off-by:
Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by:
Vasily Gorbik <gor@linux.ibm.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
- 01 Jul, 2020 3 commits
-
-
Khalid Elmously authored
Signed-off-by:Khalid Elmously <khalid.elmously@canonical.com>
-
Khalid Elmously authored
BugLink: https://bugs.launchpad.net/bugs/1885514 Properties: no-test-build Signed-off-by:
-
Khalid Elmously authored
Ignore: yes Signed-off-by:
-
- 30 Jun, 2020 33 commits
-
-
Kamal Mostafa authored
BugLink: https://bugs.launchpad.net/bugs/1884564 Ignore: yes Signed-off-by:
-
Greg Kroah-Hartman authored
BugLink: https://bugs.launchpad.net/bugs/1884564Signed-off-by:
-
Adrian Hunter authored
BugLink: https://bugs.launchpad.net/bugs/1884564 commit 85afd355 upstream. Reportedly, from 19.10 Ubuntu has begun mixing up the location of some debug symbol files, putting files expected to be in /usr/lib/debug/usr/lib into /usr/lib/debug/lib instead. Fix by adding another dso_binary_type. Example on Ubuntu 20.04 Before: $ perf record -e intel_pt//u uname Linux [ perf record: Woken up 1 times to write data ] [ perf record: Captured and wrote 0.030 MB perf.data ] $ perf script --call-trace | head -5 uname 14003 [005] 15321.764958566: cbr: 42 freq: 4219 MHz (156%) uname 14003 [005] 15321.764958566: (/usr/lib/x86_64-linux-gnu/ld-2.31.so ) 7f1e71cc4100 uname 14003 [005] 15321.764961566: (/usr/lib/x86_64-linux-gnu/ld-2.31.so ) 7f1e71cc4df0 uname 14003 [005] 15321.764961900: (/usr/lib/x86_64-linux-gnu/ld-2.31.so ) 7f1e71cc4e18 uname 14003 [005] 15321.764963233: (/usr/lib/x86_64-linux-gnu/ld-2.31.so ) 7f1e71cc5128 After: $ perf script --call-trace | head -5 uname 14003 [005] 15321.764958566: cbr: 42 freq: 4219 MHz (156%) uname 14003 [005] 15321.764958566: (/usr/lib/x86_64-linux-gnu/ld-2.31.so ) _start uname 14003 [005] 15321.764961566: (/usr/lib/x86_64-linux-gnu/ld-2.31.so ) _dl_start uname 14003 [005] 15321.764961900: (/usr/lib/x86_64-linux-gnu/ld-2.31.so ) _dl_start uname 14003 [005] 15321.764963233: (/usr/lib/x86_64-linux-gnu/ld-2.31.so ) _dl_start Reported-by:
Travis Downs <travis.downs@gmail.com> Signed-off-by:
Adrian Hunter <adrian.hunter@intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: stable@vger.kernel.org Link: http://lore.kernel.org/lkml/20200526155207.9172-1-adrian.hunter@intel.comSigned-off-by:
Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
-
Masami Hiramatsu authored
BugLink: https://bugs.launchpad.net/bugs/1884564 commit f41ebe9d upstream. When a probe point is expanded to several places (like inlined) and if some of them are skipped because of blacklisted or __init function, those trace_events has no event name. It must be skipped while showing results. Without this fix, you can see "(null):(null)" on the list, # ./perf probe request_resource reserve_setup is out of .text, skip it. Added new events: (null):(null) (on request_resource) probe:request_resource (on request_resource) You can now use it in all perf tools, such as: perf record -e probe:request_resource -aR sleep 1 # With this fix, it is ignored: # ./perf probe request_resource reserve_setup is out of .text, skip it. Added new events: probe:request_resource (on request_resource) You can now use it in all perf tools, such as: perf record -e probe:request_resource -aR sleep 1 # Fixes: 5a51fcd1 ("perf probe: Skip kernel symbols which is out of .text") Signed-off-by:
Masami Hiramatsu <mhiramat@kernel.org> Tested-by:
-
H. Nikolaus Schaller authored
BugLink: https://bugs.launchpad.net/bugs/1884564 commit 5e02f3b3 upstream. Otherwise it will corrupt the console log during debugging. Fixes: 7b5362a6 ("w1: omap_hdq: Fix some error/debug handling.") Cc: stable@vger.kernel.org Acked-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
H. Nikolaus Schaller <hns@goldelico.com> Link: https://lore.kernel.org/r/cd0d55749a091214106575f6e1d363c6db56622f.1590255176.git.hns@goldelico.comSigned-off-by:
-
NeilBrown authored
BugLink: https://bugs.launchpad.net/bugs/1884564 commit 24c5efe4 upstream. gss_mech_register() calls svcauth_gss_register_pseudoflavor() for each flavour, but gss_mech_unregister() does not call auth_domain_put(). This is unbalanced and makes it impossible to reload the module. Change svcauth_gss_register_pseudoflavor() to return the registered auth_domain, and save it for later release. Cc: stable@vger.kernel.org (v2.6.12+) Link: https://bugzilla.kernel.org/show_bug.cgi?id=206651Signed-off-by:
NeilBrown <neilb@suse.de> Signed-off-by:
J. Bruce Fields <bfields@redhat.com> Signed-off-by:
-
NeilBrown authored
BugLink: https://bugs.launchpad.net/bugs/1884564 commit d47a5dc2 upstream. There is no valid case for supporting duplicate pseudoflavor registrations. Currently the silent acceptance of such registrations is hiding a bug. The rpcsec_gss_krb5 module registers 2 flavours but does not unregister them, so if you load, unload, reload the module, it will happily continue to use the old registration which now has pointers to the memory were the module was originally loaded. This could lead to unexpected results. So disallow duplicate registrations. Link: https://bugzilla.kernel.org/show_bug.cgi?id=206651 Cc: stable@vger.kernel.org (v2.6.12+) Signed-off-by:
-
Masahiro Yamada authored
BugLink: https://bugs.launchpad.net/bugs/1884564 commit 4b50c8c4 upstream. This code does not work as stated in the comment. $(CONFIG_MODVERSIONS) is always empty because it is expanded before include/config/auto.conf is included. Hence, 'make modules' with CONFIG_MODVERSION=y cannot record the version CRCs. This has been broken since 2003, commit ("kbuild: Enable modules to be build using the "make dir/" syntax"). [1] [1]: https://git.kernel.org/pub/scm/linux/kernel/git/history/history.git/commit/?id=15c6240cdc44bbeef3c4797ec860f9765ef4f1a7 Cc: linux-stable <stable@vger.kernel.org> # v2.5.71+ Signed-off-by:
Masahiro Yamada <masahiroy@kernel.org> Signed-off-by:
-
Michael Ellerman authored
BugLink: https://bugs.launchpad.net/bugs/1884564 commit 93900337 upstream. create_cpu_loop() calls smu_sat_get_sdb_partition() which does kmalloc() and returns the allocated buffer. In fact it's called twice, and neither buffer is freed. This results in a memory leak as reported by Erhard: unreferenced object 0xc00000047081f840 (size 32): comm "kwindfarm", pid 203, jiffies 4294880630 (age 5552.877s) hex dump (first 32 bytes): c8 06 02 7f ff 02 ff 01 fb bf 00 41 00 20 00 00 ...........A. .. 00 07 89 37 00 a0 00 00 00 00 00 00 00 00 00 00 ...7............ backtrace: [<0000000083f0a65c>] .smu_sat_get_sdb_partition+0xc4/0x2d0 [windfarm_smu_sat] [<000000003010fcb7>] .pm112_wf_notify+0x104c/0x13bc [windfarm_pm112] [<00000000b958b2dd>] .notifier_call_chain+0xa8/0x180 [<0000000070490868>] .blocking_notifier_call_chain+0x64/0x90 [<00000000131d8149>] .wf_thread_func+0x114/0x1a0 [<000000000d54838d>] .kthread+0x13c/0x190 [<00000000669b72bc>] .ret_from_kernel_thread+0x58/0x64 unreferenced object 0xc0000004737089f0 (size 16): comm "kwindfarm", pid 203, jiffies 4294880879 (age 5552.050s) hex dump (first 16 bytes): c4 04 01 7f 22 11 e0 e6 ff 55 7b 12 ec 11 00 00 ...."....U{..... backtrace: [<0000000083f0a65c>] .smu_sat_get_sdb_partition+0xc4/0x2d0 [windfarm_smu_sat] [<00000000b94ef7e1>] .pm112_wf_notify+0x1294/0x13bc [windfarm_pm112] [<00000000b958b2dd>] .notifier_call_chain+0xa8/0x180 [<0000000070490868>] .blocking_notifier_call_chain+0x64/0x90 [<00000000131d8149>] .wf_thread_func+0x114/0x1a0 [<000000000d54838d>] .kthread+0x13c/0x190 [<00000000669b72bc>] .ret_from_kernel_thread+0x58/0x64 Fix it by rearranging the logic so we deal with each buffer separately, which then makes it easy to free the buffer once we're done with it. Fixes: ac171c46 ("[PATCH] powerpc: Thermal control for dual core G5s") Cc: stable@vger.kernel.org # v2.6.16+ Reported-by:
Erhard F. <erhard_f@mailbox.org> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Tested-by:
-
Dmitry Osipenko authored
BugLink: https://bugs.launchpad.net/bugs/1884564 commit 35509737 upstream. The PL310 Auxiliary Control Register shouldn't have the "Full line of zero" optimization bit being set before L2 cache is enabled. The L2X0 driver takes care of enabling the optimization by itself. This patch fixes a noisy error message on Tegra20 and Tegra30 telling that cache optimization is erroneously enabled without enabling it for the CPU: L2C-310: enabling full line of zeros but not enabled in Cortex-A9 Cc: <stable@vger.kernel.org> Signed-off-by:
Dmitry Osipenko <digetx@gmail.com> Tested-by:
Nicolas Chauvet <kwizart@gmail.com> Signed-off-by:
Thierry Reding <treding@nvidia.com> Signed-off-by:
-
Douglas Anderson authored
BugLink: https://bugs.launchpad.net/bugs/1884564 commit b5945214 upstream. cpu_pm_notify() is basically a wrapper of notifier_call_chain(). notifier_call_chain() doesn't initialize *nr_calls to 0 before it starts incrementing it--presumably it's up to the callers to do this. Unfortunately the callers of cpu_pm_notify() don't init *nr_calls. This potentially means you could get too many or two few calls to CPU_PM_ENTER_FAILED or CPU_CLUSTER_PM_ENTER_FAILED depending on the luck of the stack. Let's fix this. Fixes: ab10023e ("cpu_pm: Add cpu power management notifiers") Cc: stable@vger.kernel.org Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reviewed-by:
Stephen Boyd <swboyd@chromium.org> Reviewed-by:
Douglas Anderson <dianders@chromium.org> Link: https://lore.kernel.org/r/20200504104917.v6.3.I2d44fc0053d019f239527a4e5829416714b7e299@changeidSigned-off-by:
Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by:
-
Al Viro authored
BugLink: https://bugs.launchpad.net/bugs/1884564 commit cf51e129 upstream. It needs access_process_vm() if the traced process does not share mm with the caller. Solution is similar to what sparc64 does. Note that genregs32_set() is only ever called with pos being 0 or 32 * sizeof(u32) (the latter - as part of PTRACE_SETREGS handling). Cc: stable@kernel.org Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Jonathan Bakker authored
BugLink: https://bugs.launchpad.net/bugs/1884564 commit f354157a upstream. Currently, for EINT_TYPE GPIOs, the CON and FLTCON registers are saved and restored over a suspend/resume cycle. However, the EINT_MASK registers are not. On S5PV210 at the very least, these registers are not retained over suspend, leading to the interrupts remaining masked upon resume and therefore no interrupts being triggered for the device. There should be no effect on any SoCs that do retain these registers as theoretically we would just be re-writing what was already there. Fixes: 7ccbc60c ("pinctrl: exynos: Handle suspend/resume of GPIO EINT registers") Cc: <stable@vger.kernel.org> Signed-off-by:
Jonathan Bakker <xc-racer2@live.ca> Signed-off-by:
Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by:
-
Anders Roxell authored
BugLink: https://bugs.launchpad.net/bugs/1884564 commit 73174acc upstream. Make sure that the POWER_RESET_VEXPRESS driver won't have bind/unbind attributes available via the sysfs, so lets be explicit here and use ".suppress_bind_attrs = true" to prevent userspace from doing something silly. Link: https://lore.kernel.org/r/20200527112608.3886105-2-anders.roxell@linaro.org Cc: stable@vger.kernel.org Signed-off-by:
Anders Roxell <anders.roxell@linaro.org> Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Kai-Heng Feng authored
BugLink: https://bugs.launchpad.net/bugs/1884564 commit 165ae7a8 upstream. igb device gets runtime suspended when there's no link partner. We can't get correct speed under that state: $ cat /sys/class/net/enp3s0/speed 1000 In addition to that, an error can also be spotted in dmesg: [ 385.991957] igb 0000:03:00.0 enp3s0: PCIe link lost Since device can only be runtime suspended when there's no link partner, we can skip reading register and let the following logic set speed and duplex with correct status. The more generic approach will be wrap get_link_ksettings() with begin() and complete() callbacks. However, for this particular issue, begin() calls igb_runtime_resume() , which tries to rtnl_lock() while the lock is already hold by upper ethtool layer. So let's take this approach until the igb_runtime_resume() no longer needs to hold rtnl_lock. CC: stable <stable@vger.kernel.org> Suggested-by:
Alexander Duyck <alexander.duyck@gmail.com> Signed-off-by:
Kai-Heng Feng <kai.heng.feng@canonical.com> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by:
-
Larry Finger authored
BugLink: https://bugs.launchpad.net/bugs/1884564 commit 6a29d134 upstream. Since the driver was first introduced into the kernel, it has only handled the ciphers associated with WEP, WPA, and WPA2. It fails with WPA3 even though mac80211 can handle those additional ciphers in software, b43legacy did not report that it could handle them. By setting MFP_CAPABLE using ieee80211_set_hw(), the problem is fixed. With this change, b43legacy will handle the ciphers it knows in hardware, and let mac80211 handle the others in software. It is not necessary to use the module parameter NOHWCRYPT to turn hardware encryption off. Although this change essentially eliminates that module parameter, I am choosing to keep it for cases where the hardware is broken, and software encryption is required for all ciphers. Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@vger.kernel.org> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200526155909.5807-3-Larry.Finger@lwfinger.netSigned-off-by:
-
Larry Finger authored
BugLink: https://bugs.launchpad.net/bugs/1884564 commit 75d057bd upstream. Since the driver was first introduced into the kernel, it has only handled the ciphers associated with WEP, WPA, and WPA2. It fails with WPA3 even though mac80211 can handle those additional ciphers in software, b43 did not report that it could handle them. By setting MFP_CAPABLE using ieee80211_set_hw(), the problem is fixed. With this change, b43 will handle the ciphers it knows in hardware, and let mac80211 handle the others in software. It is not necessary to use the module parameter NOHWCRYPT to turn hardware encryption off. Although this change essentially eliminates that module parameter, I am choosing to keep it for cases where the hardware is broken, and software encryption is required for all ciphers. Reported-and-tested-by:
Rui Salvaterra <rsalvaterra@gmail.com> Signed-off-by:
-
Larry Finger authored
BugLink: https://bugs.launchpad.net/bugs/1884564 commit ec4d3e3a upstream. This patch fixes commit 75388acd ("add mac80211-based driver for legacy BCM43xx devices") In https://bugzilla.kernel.org/show_bug.cgi?id=207093, a defect in b43legacy is reported. Upon testing, thus problem exists on PPC and X86 platforms, is present in the oldest kernel tested (3.2), and has been present in the driver since it was first added to the kernel. The problem is a corrupted channel status received from the device. Both the internal card in a PowerBook G4 and the PCMCIA version (Broadcom BCM4306 with PCI ID 14e4:4320) have the problem. Only Rev, 2 (revision 4 of the 802.11 core) of the chip has been tested. No other devices using b43legacy are available for testing. Various sources of the problem were considered. Buffer overrun and other sources of corruption within the driver were rejected because the faulty channel status is always the same, not a random value. It was concluded that the faulty data is coming from the device, probably due to a firmware bug. As that source is not available, the driver must take appropriate action to recover. At present, the driver reports the error, and them continues to process the bad packet. This is believed that to be a mistake, and the correct action is to drop the correpted packet. Fixes: 75388acd ("add mac80211-based driver for legacy BCM43xx devices") Cc: Stable <stable@vger.kernel.org> Signed-off-by:
-
Chuhong Yuan authored
BugLink: https://bugs.launchpad.net/bugs/1884564 commit 9453264e upstream. go7007_snd_init() misses a snd_card_free() in an error path. Add the missed call to fix it. Signed-off-by:
Chuhong Yuan <hslester96@gmail.com> Signed-off-by:
Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by:
Mauro Carvalho Chehab <mchehab+huawei@kernel.org> [Salvatore Bonaccorso: Adjust context for backport to versions which do not contain c0decac1 ("media: use strscpy() instead of strlcpy()") and ba78170e ("media: go7007: Fix misuse of strscpy")] Signed-off-by:
Salvatore Bonaccorso <carnil@debian.org> Signed-off-by:
-
Christian Lamparter authored
BugLink: https://bugs.launchpad.net/bugs/1884564 commit b14fba7e upstream. This patch follows up on a bug-report by Frank Schäfer that discovered P2P GO wasn't working with wpa_supplicant. This patch removes part of the broken P2P GO support but keeps the vif switchover code in place. Cc: <stable@vger.kernel.org> Link: <https://lkml.kernel.org/r/3a9d86b6-744f-e670-8792-9167257edef8@googlemail.com> Reported-by:
Frank Schäfer <fschaefer.oss@googlemail.com> Signed-off-by:
Christian Lamparter <chunkeey@gmail.com> Signed-off-by:
-
Punit Agrawal authored
BugLink: https://bugs.launchpad.net/bugs/1884564 commit d601afca upstream. It's an error if the value of the RX/TX tail descriptor does not match what was written. The error condition is true regardless the duration of the interference from ME. But the driver only performs the reset if E1000_ICH_FWSM_PCIM2PCI_COUNT (2000) iterations of 50us delay have transpired. The extra condition can lead to inconsistency between the state of hardware as expected by the driver. Fix this by dropping the check for number of delay iterations. While at it, also make __ew32_prepare() static as it's not used anywhere else. CC: stable <stable@vger.kernel.org> Signed-off-by:
Punit Agrawal <punit1.agrawal@toshiba.co.jp> Reviewed-by:
Alexander Duyck <alexander.h.duyck@linux.intel.com> Tested-by:
-
Ashok Raj authored
BugLink: https://bugs.launchpad.net/bugs/1884564 commit aa0ce96d upstream. Root Complex Integrated Endpoints (RCiEPs) do not have an upstream bridge, so pci_configure_mps() previously ignored them, which may result in reduced performance. Instead, program the Max_Payload_Size of RCiEPs to the maximum supported value (unless it is limited for the PCIE_BUS_PEER2PEER case). This also affects the subsequent programming of Max_Read_Request_Size because Linux programs MRRS based on the MPS value. Fixes: 9dae3a97 ("PCI: Move MPS configuration check to pci_configure_device()") Link: https://lore.kernel.org/r/1585343775-4019-1-git-send-email-ashok.raj@intel.comTested-by:
Dave Jiang <dave.jiang@intel.com> Signed-off-by:
Ashok Raj <ashok.raj@intel.com> Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Cc: stable@vger.kernel.org Signed-off-by:
-
Roberto Sassu authored
BugLink: https://bugs.launchpad.net/bugs/1884564 [ Upstream commit 067a436b ] This patch prevents the following oops: [ 10.771813] BUG: kernel NULL pointer dereference, address: 0000000000000 [...] [ 10.779790] RIP: 0010:ima_match_policy+0xf7/0xb80 [...] [ 10.798576] Call Trace: [ 10.798993] ? ima_lsm_policy_change+0x2b0/0x2b0 [ 10.799753] ? inode_init_owner+0x1a0/0x1a0 [ 10.800484] ? _raw_spin_lock+0x7a/0xd0 [ 10.801592] ima_must_appraise.part.0+0xb6/0xf0 [ 10.802313] ? ima_fix_xattr.isra.0+0xd0/0xd0 [ 10.803167] ima_must_appraise+0x4f/0x70 [ 10.804004] ima_post_path_mknod+0x2e/0x80 [ 10.804800] do_mknodat+0x396/0x3c0 It occurs when there is a failure during IMA initialization, and ima_init_policy() is not called. IMA hooks still call ima_match_policy() but ima_rules is NULL. This patch prevents the crash by directly assigning the ima_default_policy pointer to ima_rules when ima_rules is defined. This wouldn't alter the existing behavior, as ima_rules is always set at the end of ima_init_policy(). Cc: stable@vger.kernel.org # 3.7.x Fixes: 07f6a794 ("ima: add appraise action keywords and default rules") Reported-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
Roberto Sassu <roberto.sassu@huawei.com> Signed-off-by:
Mimi Zohar <zohar@linux.ibm.com> Signed-off-by:
-
Omar Sandoval authored
BugLink: https://bugs.launchpad.net/bugs/1884564 [ Upstream commit 6d3113a1 ] In btrfs_submit_direct_hook(), if a direct I/O write doesn't span a RAID stripe or chunk, we submit orig_bio without cloning it. In this case, we don't increment pending_bios. Then, if btrfs_submit_dio_bio() fails, we decrement pending_bios to -1, and we never complete orig_bio. Fix it by initializing pending_bios to 1 instead of incrementing later. Fixing this exposes another bug: we put orig_bio prematurely and then put it again from end_io. Fix it by not putting orig_bio. After this change, pending_bios is really more of a reference count, but I'll leave that cleanup separate to keep the fix small. Fixes: e65e1535 ("btrfs: fix panic caused by direct IO") CC: stable@vger.kernel.org # 4.4+ Reviewed-by:
Nikolay Borisov <nborisov@suse.com> Reviewed-by:
Josef Bacik <josef@toxicpanda.com> Reviewed-by:
Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by:
Omar Sandoval <osandov@fb.com> Signed-off-by:
David Sterba <dsterba@suse.com> Signed-off-by:
-
Marcos Paulo de Souza authored
BugLink: https://bugs.launchpad.net/bugs/1884564 [ Upstream commit 89efda52 ] Whenever a chown is executed, all capabilities of the file being touched are lost. When doing incremental send with a file with capabilities, there is a situation where the capability can be lost on the receiving side. The sequence of actions bellow shows the problem: $ mount /dev/sda fs1 $ mount /dev/sdb fs2 $ touch fs1/foo.bar $ setcap cap_sys_nice+ep fs1/foo.bar $ btrfs subvolume snapshot -r fs1 fs1/snap_init $ btrfs send fs1/snap_init | btrfs receive fs2 $ chgrp adm fs1/foo.bar $ setcap cap_sys_nice+ep fs1/foo.bar $ btrfs subvolume snapshot -r fs1 fs1/snap_complete $ btrfs subvolume snapshot -r fs1 fs1/snap_incremental $ btrfs send fs1/snap_complete | btrfs receive fs2 $ btrfs send -p fs1/snap_init fs1/snap_incremental | btrfs receive fs2 At this point, only a chown was emitted by "btrfs send" since only the group was changed. This makes the cap_sys_nice capability to be dropped from fs2/snap_incremental/foo.bar To fix that, only emit capabilities after chown is emitted. The current code first checks for xattrs that are new/changed, emits them, and later emit the chown. Now, __process_new_xattr skips capabilities, letting only finish_inode_if_needed to emit them, if they exist, for the inode being processed. This behavior was being worked around in "btrfs receive" side by caching the capability and only applying it after chown. Now, xattrs are only emmited _after_ chown, making that workaround not needed anymore. Link: https://github.com/kdave/btrfs-progs/issues/202 CC: stable@vger.kernel.org # 4.4+ Suggested-by:
Filipe Manana <fdmanana@suse.com> Reviewed-by:
Marcos Paulo de Souza <mpdesouza@suse.com> Signed-off-by:
-
Filipe Manana authored
BugLink: https://bugs.launchpad.net/bugs/1884564 [ Upstream commit 1ec9a1ae ] If we delete a snapshot, fsync its parent directory and crash/power fail before the next transaction commit, on the next mount when we attempt to replay the log tree of the root containing the parent directory we will fail and prevent the filesystem from mounting, which is solvable by wiping out the log trees with the btrfs-zero-log tool but very inconvenient as we will lose any data and metadata fsynced before the parent directory was fsynced. For example: $ mkfs.btrfs -f /dev/sdc $ mount /dev/sdc /mnt $ mkdir /mnt/testdir $ btrfs subvolume snapshot /mnt /mnt/testdir/snap $ btrfs subvolume delete /mnt/testdir/snap $ xfs_io -c "fsync" /mnt/testdir < crash / power failure and reboot > $ mount /dev/sdc /mnt mount: mount(2) failed: No such file or directory And in dmesg/syslog we get the following message and trace: [192066.361162] BTRFS info (device dm-0): failed to delete reference to snap, inode 257 parent 257 [192066.363010] ------------[ cut here ]------------ [192066.365268] WARNING: CPU: 4 PID: 5130 at fs/btrfs/inode.c:3986 __btrfs_unlink_inode+0x17a/0x354 [btrfs]() [192066.367250] BTRFS: Transaction aborted (error -2) [192066.368401] Modules linked in: btrfs dm_flakey dm_mod ppdev sha256_generic xor raid6_pq hmac drbg ansi_cprng aesni_intel acpi_cpufreq tpm_tis aes_x86_64 tpm ablk_helper evdev cryptd sg parport_pc i2c_piix4 psmouse lrw parport i2c_core pcspkr gf128mul processor serio_raw glue_helper button loop autofs4 ext4 crc16 mbcache jbd2 sd_mod sr_mod cdrom ata_generic virtio_scsi ata_piix libata virtio_pci virtio_ring crc32c_intel scsi_mod e1000 virtio floppy [last unloaded: btrfs] [192066.377154] CPU: 4 PID: 5130 Comm: mount Tainted: G W 4.4.0-rc6-btrfs-next-20+ #1 [192066.378875] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS by qemu-project.org 04/01/2014 [192066.380889] 0000000000000000 ffff880143923670 ffffffff81257570 ffff8801439236b8 [192066.382561] ffff8801439236a8 ffffffff8104ec07 ffffffffa039dc2c 00000000fffffffe [192066.384191] ffff8801ed31d000 ffff8801b9fc9c88 ffff8801086875e0 ffff880143923710 [192066.385827] Call Trace: [192066.386373] [<ffffffff81257570>] dump_stack+0x4e/0x79 [192066.387387] [<ffffffff8104ec07>] warn_slowpath_common+0x99/0xb2 [192066.388429] [<ffffffffa039dc2c>] ? __btrfs_unlink_inode+0x17a/0x354 [btrfs] [192066.389236] [<ffffffff8104ec68>] warn_slowpath_fmt+0x48/0x50 [192066.389884] [<ffffffffa039dc2c>] __btrfs_unlink_inode+0x17a/0x354 [btrfs] [192066.390621] [<ffffffff81184b55>] ? iput+0xb0/0x266 [192066.391200] [<ffffffffa039ea25>] btrfs_unlink_inode+0x1c/0x3d [btrfs] [192066.391930] [<ffffffffa03ca623>] check_item_in_log+0x1fe/0x29b [btrfs] [192066.392715] [<ffffffffa03ca827>] replay_dir_deletes+0x167/0x1cf [btrfs] [192066.393510] [<ffffffffa03cccc7>] replay_one_buffer+0x417/0x570 [btrfs] [192066.394241] [<ffffffffa03ca164>] walk_up_log_tree+0x10e/0x1dc [btrfs] [192066.394958] [<ffffffffa03cac72>] walk_log_tree+0xa5/0x190 [btrfs] [192066.395628] [<ffffffffa03ce8b8>] btrfs_recover_log_trees+0x239/0x32c [btrfs] [192066.396790] [<ffffffffa03cc8b0>] ? replay_one_extent+0x50a/0x50a [btrfs] [192066.397891] [<ffffffffa0394041>] open_ctree+0x1d8b/0x2167 [btrfs] [192066.398897] [<ffffffffa03706e1>] btrfs_mount+0x5ef/0x729 [btrfs] [192066.399823] [<ffffffff8108ad98>] ? trace_hardirqs_on+0xd/0xf [192066.400739] [<ffffffff8108959b>] ? lockdep_init_map+0xb9/0x1b3 [192066.401700] [<ffffffff811714b9>] mount_fs+0x67/0x131 [192066.402482] [<ffffffff81188560>] vfs_kern_mount+0x6c/0xde [192066.403930] [<ffffffffa03702bd>] btrfs_mount+0x1cb/0x729 [btrfs] [192066.404831] [<ffffffff8108ad98>] ? trace_hardirqs_on+0xd/0xf [192066.405726] [<ffffffff8108959b>] ? lockdep_init_map+0xb9/0x1b3 [192066.406621] [<ffffffff811714b9>] mount_fs+0x67/0x131 [192066.407401] [<ffffffff81188560>] vfs_kern_mount+0x6c/0xde [192066.408247] [<ffffffff8118ae36>] do_mount+0x893/0x9d2 [192066.409047] [<ffffffff8113009b>] ? strndup_user+0x3f/0x8c [192066.409842] [<ffffffff8118b187>] SyS_mount+0x75/0xa1 [192066.410621] [<ffffffff8147e517>] entry_SYSCALL_64_fastpath+0x12/0x6b [192066.411572] ---[ end trace 2de42126c1e0a0f0 ]--- [192066.412344] BTRFS: error (device dm-0) in __btrfs_unlink_inode:3986: errno=-2 No such entry [192066.413748] BTRFS: error (device dm-0) in btrfs_replay_log:2464: errno=-2 No such entry (Failed to recover log tree) [192066.415458] BTRFS error (device dm-0): cleaner transaction attach returned -30 [192066.444613] BTRFS: open_ctree failed This happens because when we are replaying the log and processing the directory entry pointing to the snapshot in the subvolume tree, we treat its btrfs_dir_item item as having a location with a key type matching BTRFS_INODE_ITEM_KEY, which is wrong because the type matches BTRFS_ROOT_ITEM_KEY and therefore must be processed differently, as the object id refers to a root number and not to an inode in the root containing the parent directory. So fix this by triggering a transaction commit if an fsync against the parent directory is requested after deleting a snapshot. This is the simplest approach for a rare use case. Some alternative that avoids the transaction commit would require more code to explicitly delete the snapshot at log replay time (factoring out common code from ioctl.c: btrfs_ioctl_snap_destroy()), special care at fsync time to remove the log tree of the snapshot's root from the log root of the root of tree roots, amongst other steps. A test case for xfstests that triggers the issue follows. seq=`basename $0` seqres=$RESULT_DIR/$seq echo "QA output created by $seq" tmp=/tmp/$$ status=1 # failure is the default! trap "_cleanup; exit \$status" 0 1 2 3 15 _cleanup() { _cleanup_flakey cd / rm -f $tmp.* } # get standard environment, filters and checks . ./common/rc . ./common/filter . ./common/dmflakey # real QA test starts here _need_to_be_root _supported_fs btrfs _supported_os Linux _require_scratch _require_dm_target flakey _require_metadata_journaling $SCRATCH_DEV rm -f $seqres.full _scratch_mkfs >>$seqres.full 2>&1 _init_flakey _mount_flakey # Create a snapshot at the root of our filesystem (mount point path), delete it, # fsync the mount point path, crash and mount to replay the log. This should # succeed and after the filesystem is mounted the snapshot should not be visible # anymore. _run_btrfs_util_prog subvolume snapshot $SCRATCH_MNT $SCRATCH_MNT/snap1 _run_btrfs_util_prog subvolume delete $SCRATCH_MNT/snap1 $XFS_IO_PROG -c "fsync" $SCRATCH_MNT _flakey_drop_and_remount [ -e $SCRATCH_MNT/snap1 ] && \ echo "Snapshot snap1 still exists after log replay" # Similar scenario as above, but this time the snapshot is created inside a # directory and not directly under the root (mount point path). mkdir $SCRATCH_MNT/testdir _run_btrfs_util_prog subvolume snapshot $SCRATCH_MNT $SCRATCH_MNT/testdir/snap2 _run_btrfs_util_prog subvolume delete $SCRATCH_MNT/testdir/snap2 $XFS_IO_PROG -c "fsync" $SCRATCH_MNT/testdir _flakey_drop_and_remount [ -e $SCRATCH_MNT/testdir/snap2 ] && \ echo "Snapshot snap2 still exists after log replay" _unmount_flakey echo "Silence is golden" status=0 exit Signed-off-by:
Liu Bo <bo.li.liu@oracle.com> Reviewed-by:
Chris Mason <clm@fb.com> Signed-off-by:
-
Harshad Shirwadkar authored
BugLink: https://bugs.launchpad.net/bugs/1884564 commit c36a71b4 upstream. If eh->eh_max is 0, EXT_MAX_EXTENT/INDEX would evaluate to unsigned (-1) resulting in illegal memory accesses. Although there is no consistent repro, we see that generic/019 sometimes crashes because of this bug. Ran gce-xfstests smoke and verified that there were no regressions. Signed-off-by:
Harshad Shirwadkar <harshadshirwadkar@gmail.com> Link: https://lore.kernel.org/r/20200421023959.20879-2-harshadshirwadkar@gmail.comSigned-off-by:
Theodore Ts'o <tytso@mit.edu> Cc: stable@kernel.org Signed-off-by:
-
Krzysztof Struczynski authored
BugLink: https://bugs.launchpad.net/bugs/1884564 commit 1129d31b upstream. Function hash_long() accepts unsigned long, while currently only one byte is passed from ima_hash_key(), which calculates a key for ima_htable. Given that hashing the digest does not give clear benefits compared to using the digest itself, remove hash_long() and return the modulus calculated on the first two bytes of the digest with the number of slots. Also reduce the depth of the hash table by doubling the number of slots. Cc: stable@vger.kernel.org Fixes: 3323eec9 ("integrity: IMA as an integrity service provider") Co-developed-by:
Krzysztof Struczynski <krzysztof.struczynski@huawei.com> Acked-by: David.Laight@aculab.com (big endian system concerns) Signed-off-by:
-
Qiushi Wu authored
BugLink: https://bugs.launchpad.net/bugs/1884564 [ Upstream commit c343bf1b ] kobject_init_and_add() takes reference even when it fails. If this function returns an error, kobject_put() must be called to properly clean up the memory associated with the object. Previous commit "b8eb7183" fixed a similar problem. Signed-off-by:
Qiushi Wu <wu000273@umn.edu> [ rjw: Subject ] Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Serge Semin authored
BugLink: https://bugs.launchpad.net/bugs/1884564 [ Upstream commit f0410bbf ] DW APB SSI DMA-part of the driver may need to perform the requested SPI-transfer synchronously. In that case the dma_transfer() callback will return 0 as a marker of the SPI transfer being finished so the SPI core doesn't need to wait and may proceed with the SPI message trasnfers pumping procedure. This will be needed to fix the problem when DMA transactions are finished, but there is still data left in the SPI Tx/Rx FIFOs being sent/received. But for now make dma_transfer to return 1 as the normal dw_spi_transfer_one() method. Signed-off-by:
Serge Semin <Sergey.Semin@baikalelectronics.ru> Cc: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru> Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Feng Tang <feng.tang@intel.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-mips@vger.kernel.org Cc: devicetree@vger.kernel.org Link: https://lore.kernel.org/r/20200529131205.31838-3-Sergey.Semin@baikalelectronics.ruSigned-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Xie XiuQi authored
BugLink: https://bugs.launchpad.net/bugs/1884564 [ Upstream commit 3b70683f ] ubsan report this warning, fix it by adding a unsigned suffix. UBSAN: signed-integer-overflow in drivers/net/ethernet/intel/ixgbe/ixgbe_common.c:2246:26 65535 * 65537 cannot be represented in type 'int' CPU: 21 PID: 7 Comm: kworker/u256:0 Not tainted 5.7.0-rc3-debug+ #39 Hardware name: Huawei TaiShan 2280 V2/BC82AMDC, BIOS 2280-V2 03/27/2020 Workqueue: ixgbe ixgbe_service_task [ixgbe] Call trace: dump_backtrace+0x0/0x3f0 show_stack+0x28/0x38 dump_stack+0x154/0x1e4 ubsan_epilogue+0x18/0x60 handle_overflow+0xf8/0x148 __ubsan_handle_mul_overflow+0x34/0x48 ixgbe_fc_enable_generic+0x4d0/0x590 [ixgbe] ixgbe_service_task+0xc20/0x1f78 [ixgbe] process_one_work+0x8f0/0xf18 worker_thread+0x430/0x6d0 kthread+0x218/0x238 ret_from_fork+0x10/0x18 Reported-by:
Hulk Robot <hulkci@huawei.com> Signed-off-by:
Xie XiuQi <xiexiuqi@huawei.com> Tested-by:
Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by:
-
YuanJunQing authored
BugLink: https://bugs.launchpad.net/bugs/1884564 [ Upstream commit 31e1b3ef ] Register "a1" is unsaved in this function, when CONFIG_TRACE_IRQFLAGS is enabled, the TRACE_IRQS_OFF macro will call trace_hardirqs_off(), and this may change register "a1". The changed register "a1" as argument will be send to do_fpe() and do_msa_fpe(). Signed-off-by:
YuanJunQing <yuanjunqing66@163.com> Signed-off-by:
Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by:
-
Jiaxun Yang authored
BugLink: https://bugs.launchpad.net/bugs/1884564 [ Upstream commit b6caa1d8 ] Don't disable MEM/IO decoding when a device have both non_compliant_bars and mmio_always_on. That would allow us quirk devices with junk in BARs but can't disable their decoding. Signed-off-by:
Jiaxun Yang <jiaxun.yang@flygoat.com> Acked-by:
Bjorn Helgaas <helgaas@kernel.org> Signed-off-by:
-
