- 09 Jan, 2017 40 commits
-
-
Geoff Levand authored
commit 6dff5b67 upstream. GCC 5 generates different code for this bootwrapper null check that causes the PS3 to hang very early in its bootup. This check is of limited value, so just get rid of it. Signed-off-by:
Geoff Levand <geoff@infradead.org> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Al Viro authored
commit c0cf3ef5 upstream. What matters when deciding if we should make a page uptodate is not how much we _wanted_ to copy, but how much we actually have copied. As it is, on architectures that do not zero tail on short copy we can leave uninitialized data in page marked uptodate. Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Ilya Dryomov authored
commit 5c056fdc upstream. After sending an authorizer (ceph_x_authorize_a + ceph_x_authorize_b), the client gets back a ceph_x_authorize_reply, which it is supposed to verify to ensure the authenticity and protect against replay attacks. The code for doing this is there (ceph_x_verify_authorizer_reply(), ceph_auth_verify_authorizer_reply() + plumbing), but it is never invoked by the the messenger. AFAICT this goes back to 2009, when ceph authentication protocols support was added to the kernel client in 4e7a5dcd ("ceph: negotiate authentication protocol; implement AUTH_NONE protocol"). The second param of ceph_connection_operations::verify_authorizer_reply is unused all the way down. Pass 0 to facilitate backporting, and kill it in the next commit. Signed-off-by:
Ilya Dryomov <idryomov@gmail.com> Reviewed-by:
Sage Weil <sage@redhat.com> Signed-off-by:
-
Alan Stern authored
commit 6496ebd7 upstream. One some systems, the firmware does not allow certain PCI devices to be put in deep D-states. This can cause problems for wakeup signalling, if the device does not support PME# in the deepest allowed suspend state. For example, Pierre reports that on his system, ACPI does not permit his xHCI host controller to go into D3 during runtime suspend -- but D3 is the only state in which the controller can generate PME# signals. As a result, the controller goes into runtime suspend but never wakes up, so it doesn't work properly. USB devices plugged into the controller are never detected. If the device relies on PME# for wakeup signals but is not capable of generating PME# in the target state, the PCI core should accurately report that it cannot do wakeup from runtime suspend. This patch modifies the pci_dev_run_wake() routine to add this check. Reported-by:
Pierre de Villemereuil <flyos@mailoo.org> Tested-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Acked-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> CC: Lukas Wunner <lukas@wunner.de> Signed-off-by:
-
Jingkui Wang authored
commit 5a8a6b89 upstream. We were assigning I2C bus controller instead of client as parent device. Besides being logically wrong, it messed up with devm handling of input device. As a result we were leaving input device and event node behind after rmmod-ing the driver, which lead to a kernel oops if one were to access the event node later. Let's remove the assignment and rely on devm_input_allocate_device() to set it up properly for us. Signed-off-by:
Jingkui Wang <jkwang@google.com> Fixes: 7132fe4f ("Input: drv260x - add TI drv260x haptics driver") Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Andrey Utkin authored
commit 5fc4b067 upstream. This fixes a lockup at device probing which happens on some solo6010 hardware samples. This is a regression introduced by commit e1ceb25a ("[media] SOLO6x10: remove unneeded register locking and barriers") The observed lockup happens in solo_set_motion_threshold() called from solo_motion_config(). This extra "flushing" is not fundamentally needed for every write, but apparently the code in driver assumes such behaviour at last in some places. Actual fix was proposed by Hans Verkuil. Fixes: e1ceb25a ("[media] SOLO6x10: remove unneeded register locking and barriers") Signed-off-by:
Andrey Utkin <andrey.utkin@corp.bluecherry.net> Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@s-opensource.com> Signed-off-by:
-
Bart Van Assche authored
commit fba332b0 upstream. Code that dereferences the struct net_device ip_ptr member must be protected with an in_dev_get() / in_dev_put() pair. Hence insert calls to these functions. Fixes: commit 7b85627b ("IB/cma: IBoE (RoCE) IP-based GID addressing") Signed-off-by:
Bart Van Assche <bart.vanassche@sandisk.com> Reviewed-by:
Moni Shoua <monis@mellanox.com> Cc: Or Gerlitz <ogerlitz@mellanox.com> Cc: Roland Dreier <roland@purestorage.com> Signed-off-by:
Doug Ledford <dledford@redhat.com> Signed-off-by:
-
Bart Van Assche authored
commit d3a2418e upstream. This patch avoids that Coverity complains about not checking the ib_find_pkey() return value. Fixes: commit 547af765 ("IB/multicast: Report errors on multicast groups if P_key changes") Signed-off-by:
-
Bart Van Assche authored
commit 11b642b8 upstream. This patch avoids that Coverity reports the following: Using uninitialized value port_attr.state when calling printk Fixes: commit 94232d9c ("IPoIB: Start multicast join process only on active ports") Signed-off-by:
Leon Romanovsky <leonro@mellanox.com> Signed-off-by:
-
Bart Van Assche authored
commit 2fe2f378 upstream. The array ib_mad_mgmt_class_table.method_table has MAX_MGMT_CLASS (80) elements. Hence compare the array index with that value instead of with IB_MGMT_MAX_METHODS (128). This patch avoids that Coverity reports the following: Overrunning array class->method_table of 80 8-byte elements at element index 127 (byte offset 1016) using index convert_mgmt_class(mad_hdr->mgmt_class) (which evaluates to 127). Fixes: commit b7ab0b19 ("IB/mad: Verify mgmt class in received MADs") Signed-off-by:
Hal Rosenstock <hal@mellanox.com> Signed-off-by:
-
Steven Rostedt (Red Hat) authored
commit 794de08a upstream. Both the wakeup and irqsoff tracers can use the function graph tracer when the display-graph option is set. The problem is that they ignore the notrace file, and record the entry of functions that would be ignored by the function_graph tracer. This causes the trace->depth to be recorded into the ring buffer. The set_graph_notrace uses a trick by adding a large negative number to the trace->depth when a graph function is to be ignored. On trace output, the graph function uses the depth to record a stack of functions. But since the depth is negative, it accesses the array with a negative number and causes an out of bounds access that can cause a kernel oops or corrupt data. Have the print functions handle cases where a tracer still records functions even when they are in set_graph_notrace. Also add warnings if the depth is below zero before accessing the array. Note, the function graph logic will still prevent the return of these functions from being recorded, which means that they will be left hanging without a return. For example: # echo '*spin*' > set_graph_notrace # echo 1 > options/display-graph # echo wakeup > current_tracer # cat trace [...] _raw_spin_lock() { preempt_count_add() { do_raw_spin_lock() { update_rq_clock(); Where it should look like: _raw_spin_lock() { preempt_count_add(); do_raw_spin_lock(); } update_rq_clock(); Cc: Namhyung Kim <namhyung.kim@lge.com> Fixes: 29ad23b0 ("ftrace: Add set_graph_notrace filter") Signed-off-by:
Steven Rostedt <rostedt@goodmis.org> Signed-off-by:
-
Marcos Paulo de Souza authored
commit e74e2599 upstream. Without this patch, the Asus X45U wireless card can't be turned on (hard-blocked), but after a suspend/resume it just starts working. Following this bug report[1], there are other cases like this one, but this Asus is the only model that I can test. [1] https://ubuntuforums.org/showthread.php?t=2181558Signed-off-by:
Marcos Paulo de Souza <marcos.souza.org@gmail.com> Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
-
Steven Rostedt (Red Hat) authored
commit 847fa1a6 upstream. With new binutils, gcc may get smart with its optimization and change a jmp from a 5 byte jump to a 2 byte one even though it was jumping to a global function. But that global function existed within a 2 byte radius, and gcc was able to optimize it. Unfortunately, that jump was also being modified when function graph tracing begins. Since ftrace expected that jump to be 5 bytes, but it was only two, it overwrote code after the jump, causing a crash. This was fixed for x86_64 with commit 8329e818, with the same subject as this commit, but nothing was done for x86_32. Fixes: d61f82d0 ("ftrace: use dynamic patching for updating mcount calls") Reported-by:
Colin Ian King <colin.king@canonical.com> Tested-by:
-
Jim Mattson authored
commit ef85b673 upstream. When L2 exits to L0 due to "exception or NMI", software exceptions (#BP and #OF) for which L1 has requested an intercept should be handled by L1 rather than L0. Previously, only hardware exceptions were forwarded to L1. Signed-off-by:
Jim Mattson <jmattson@google.com> Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
-
Paul Mackerras authored
commit f064a0de upstream. The hashed page table MMU in POWER processors can update the R (reference) and C (change) bits in a HPTE at any time until the HPTE has been invalidated and the TLB invalidation sequence has completed. In kvmppc_h_protect, which implements the H_PROTECT hypercall, we read the HPTE, modify the second doubleword, invalidate the HPTE in memory, do the TLB invalidation sequence, and then write the modified value of the second doubleword back to memory. In doing so we could overwrite an R/C bit update done by hardware between when we read the HPTE and when the TLB invalidation completed. To fix this we re-read the second doubleword after the TLB invalidation and OR in the (possibly) new values of R and C. We can use an OR since hardware only ever sets R and C, never clears them. This race was found by code inspection. In principle this bug could cause occasional guest memory corruption under host memory pressure. Fixes: a8606e20 ("KVM: PPC: Handle some PAPR hcalls in the kernel", 2011-06-29) Signed-off-by:
Paul Mackerras <paulus@ozlabs.org> Signed-off-by:
-
Paul Mackerras authored
commit 0d808df0 upstream. When switching from/to a guest that has a transaction in progress, we need to save/restore the checkpointed register state. Although XER is part of the CPU state that gets checkpointed, the code that does this saving and restoring doesn't save/restore XER. This fixes it by saving and restoring the XER. To allow userspace to read/write the checkpointed XER value, we also add a new ONE_REG specifier. The visible effect of this bug is that the guest may see its XER value being corrupted when it uses transactions. Fixes: e4e38121 ("KVM: PPC: Book3S HV: Add transactional memory support") Fixes: 0a8eccef ("KVM: PPC: Book3S HV: Add missing code for transaction reclaim on guest exit") Signed-off-by:
Thomas Huth <thuth@redhat.com> Signed-off-by:
-
Konstantin Khlebnikov authored
commit e8d7c332 upstream. Current implementation employ 16bit counter of active stripes in lower bits of bio->bi_phys_segments. If request is big enough to overflow this counter bio will be completed and freed too early. Fortunately this not happens in default configuration because several other limits prevent that: stripe_cache_size * nr_disks effectively limits count of active stripes. And small max_sectors_kb at lower disks prevent that during normal read/write operations. Overflow easily happens in discard if it's enabled by module parameter "devices_handle_discard_safely" and stripe_cache_size is set big enough. This patch limits requests size with 256Mb - 8Kb to prevent overflows. Signed-off-by:
Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Cc: Shaohua Li <shli@kernel.org> Cc: Neil Brown <neilb@suse.com> Signed-off-by:
Shaohua Li <shli@fb.com> Signed-off-by:
-
Josh Cartwright authored
commit 04da7380 upstream. The use of IRQF_ONESHOT when registering an interrupt handler with request_irq() is non-sensical. Not only that, it also prevents the handler from being threaded when it otherwise should be w/ IRQ_FORCED_THREADING is enabled. This causes the following deadlock observed by Sean Nyekjaer on -rt: Internal error: Oops - BUG: 0 [#1] PREEMPT SMP ARM [..] rt_spin_lock_slowlock from queue_kthread_work queue_kthread_work from sc16is7xx_irq sc16is7xx_irq [sc16is7xx] from handle_irq_event_percpu handle_irq_event_percpu from handle_irq_event handle_irq_event from handle_level_irq handle_level_irq from generic_handle_irq generic_handle_irq from mxc_gpio_irq_handler mxc_gpio_irq_handler from mx3_gpio_irq_handler mx3_gpio_irq_handler from generic_handle_irq generic_handle_irq from __handle_domain_irq __handle_domain_irq from gic_handle_irq gic_handle_irq from __irq_svc __irq_svc from rt_spin_unlock rt_spin_unlock from kthread_worker_fn kthread_worker_fn from kthread kthread from ret_from_fork Fixes: 9e6f4ca3 ("sc16is7xx: use kthread_worker for tx_work and irq") Reported-by:
Sean Nyekjaer <sean.nyekjaer@prevas.dk> Signed-off-by:
Josh Cartwright <joshc@ni.com> Cc: linux-rt-users@vger.kernel.org Cc: Jakub Kicinski <moorray3@wp.pl> Cc: linux-serial@vger.kernel.org Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by:
Julia Cartwright <julia@ni.com> Acked-by:
Jakub Kicinski <kubakici@wp.pl> Signed-off-by:
-
Gerald Schaefer authored
commit 5457e03d upstream. The buffer for iucv_message_receive() needs to be below 2 GB. In __iucv_message_receive(), the buffer address is casted to an u32, which would result in either memory corruption or an addressing exception when using addresses >= 2 GB. Fix this by using GFP_DMA for the buffer allocation. Signed-off-by:
Gerald Schaefer <gerald.schaefer@de.ibm.com> Signed-off-by:
Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by:
-
Yves-Alexis Perez authored
commit 2e700f8d upstream. When you use the firmware usermode helper fallback with a timeout value set to a value greater than INT_MAX (2147483647) a cast overflow issue causes the timeout value to go negative and breaks all usermode helper loading. This regression was introduced through commit 68ff2a00 ("firmware_loader: handle timeout via wait_for_completion_interruptible_timeout()") on kernel v4.0. The firmware_class drivers relies on the firmware usermode helper fallback as a mechanism to look for firmware if the direct filesystem search failed only if: a) You've enabled CONFIG_FW_LOADER_USER_HELPER_FALLBACK (not many distros): Then all of these callers will rely on the fallback mechanism in case the firmware is not found through an initial direct filesystem lookup: o request_firmware() o request_firmware_into_buf() o request_firmware_nowait() b) If you've only enabled CONFIG_FW_LOADER_USER_HELPER (most distros): Then only callers using request_firmware_nowait() with the second argument set to false, this explicitly is requesting the UMH firmware fallback to be relied on in case the first filesystem lookup fails. Using Coccinelle SmPL grammar we have identified only two drivers explicitly requesting the UMH firmware fallback mechanism: - drivers/firmware/dell_rbu.c - drivers/leds/leds-lp55xx-common.c Since most distributions only enable CONFIG_FW_LOADER_USER_HELPER the biggest impact of this regression are users of the dell_rbu and leds-lp55xx-common device driver which required the UMH to find their respective needed firmwares. The default timeout for the UMH is set to 60 seconds always, as of commit 68ff2a00 ("firmware_loader: handle timeout via wait_for_completion_interruptible_timeout()") the timeout was bumped to MAX_JIFFY_OFFSET ((LONG_MAX >> 1)-1). Additionally the MAX_JIFFY_OFFSET value was also used if the timeout was configured by a user to 0. The following works: echo 2147483647 > /sys/class/firmware/timeout But both of the following set the timeout to MAX_JIFFY_OFFSET even if we display 0 back to userspace: echo 2147483648 > /sys/class/firmware/timeout cat /sys/class/firmware/timeout 0 echo 0> /sys/class/firmware/timeout cat /sys/class/firmware/timeout 0 A max value of INT_MAX (2147483647) seconds is therefore implicit due to the another cast with simple_strtol(). This fixes the secondary cast (the first one is simple_strtol() but its an issue only by forcing an implicit limit) by re-using the timeout variable and only setting retval in appropriate cases. Lastly worth noting systemd had ripped out the UMH firmware fallback mechanism from udev since udev 2014 via commit be2ea723b1d023b3d ("udev: remove userspace firmware loading support"), so as of systemd v217. Signed-off-by:
Yves-Alexis Perez <corsac@corsac.net> Fixes: 68ff2a00 "firmware_loader: handle timeout via wait_for_completion_interruptible_timeout()" Cc: Luis R. Rodriguez <mcgrof@kernel.org> Cc: Ming Lei <ming.lei@canonical.com> Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by:
Luis R. Rodriguez <mcgrof@kernel.org> Reviewed-by:
Bjorn Andersson <bjorn.andersson@linaro.org> [mcgrof@kernel.org: gave commit log a whole lot of love] Signed-off-by:
-
Vineet Gupta authored
commit 08fe0079 upstream. An ARC700 customer reported linux boot crashes when upgrading to bigger L1 dcache (64K from 32K). Turns out they had an aliasing VIPT config and current code only assumed 2 colours, while theirs had 4. So default to 4 colours and complain if there are fewer. Ideally this needs to be a Kconfig option, but heck that's too much of hassle for a single user. Signed-off-by:
Vineet Gupta <vgupta@synopsys.com> Signed-off-by:
-
Wei Fang authored
commit d2a14525 upstream. A race between scanning and fc_remote_port_delete() may result in a permanent stop if the device gets blocked before scsi_sysfs_add_sdev() and unblocked after. The reason is that blocking a device sets both the SDEV_BLOCKED state and the QUEUE_FLAG_STOPPED. However, scsi_sysfs_add_sdev() unconditionally sets SDEV_RUNNING which causes the device to be ignored by scsi_target_unblock() and thus never have its QUEUE_FLAG_STOPPED cleared leading to a device which is apparently running but has a stopped queue. We actually have two places where SDEV_RUNNING is set: once in scsi_add_lun() which respects the blocked flag and once in scsi_sysfs_add_sdev() which doesn't. Since the second set is entirely spurious, simply remove it to fix the problem. Reported-by:
Zengxi Chen <chenzengxi@huawei.com> Signed-off-by:
Wei Fang <fangwei1@huawei.com> Reviewed-by:
Ewan D. Milne <emilne@redhat.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Steffen Maier authored
commit 6f2ce1c6 upstream. It is unavoidable that zfcp_scsi_queuecommand() has to finish requests with DID_IMM_RETRY (like fc_remote_port_chkready()) during the time window when zfcp detected an unavailable rport but fc_remote_port_delete(), which is asynchronous via zfcp_scsi_schedule_rport_block(), has not yet blocked the rport. However, for the case when the rport becomes available again, we should prevent unblocking the rport too early. In contrast to other FCP LLDDs, zfcp has to open each LUN with the FCP channel hardware before it can send I/O to a LUN. So if a port already has LUNs attached and we unblock the rport just after port recovery, recoveries of LUNs behind this port can still be pending which in turn force zfcp_scsi_queuecommand() to unnecessarily finish requests with DID_IMM_RETRY. This also opens a time window with unblocked rport (until the followup LUN reopen recovery has finished). If a scsi_cmnd timeout occurs during this time window fc_timed_out() cannot work as desired and such command would indeed time out and trigger scsi_eh. This prevents a clean and timely path failover. This should not happen if the path issue can be recovered on FC transport layer such as path issues involving RSCNs. Fix this by only calling zfcp_scsi_schedule_rport_register(), to asynchronously trigger fc_remote_port_add(), after all LUN recoveries as children of the rport have finished and no new recoveries of equal or higher order were triggered meanwhile. Finished intentionally includes any recovery result no matter if successful or failed (still unblock rport so other successful LUNs work). For simplicity, we check after each finished LUN recovery if there is another LUN recovery pending on the same port and then do nothing. We handle the special case of a successful recovery of a port without LUN children the same way without changing this case's semantics. For debugging we introduce 2 new trace records written if the rport unblock attempt was aborted due to still unfinished or freshly triggered recovery. The records are only written above the default trace level. Benjamin noticed the important special case of new recovery that can be triggered between having given up the erp_lock and before calling zfcp_erp_action_cleanup() within zfcp_erp_strategy(). We must avoid the following sequence: ERP thread rport_work other context ------------------------- -------------- -------------------------------- port is unblocked, rport still blocked, due to pending/running ERP action, so ((port->status & ...UNBLOCK) != 0) and (port->rport == NULL) unlock ERP zfcp_erp_action_cleanup() case ZFCP_ERP_ACTION_REOPEN_LUN: zfcp_erp_try_rport_unblock() ((status & ...UNBLOCK) != 0) [OLD!] zfcp_erp_port_reopen() lock ERP zfcp_erp_port_block() port->status clear ...UNBLOCK unlock ERP zfcp_scsi_schedule_rport_block() port->rport_task = RPORT_DEL queue_work(rport_work) zfcp_scsi_rport_work() (port->rport_task != RPORT_ADD) port->rport_task = RPORT_NONE zfcp_scsi_rport_block() if (!port->rport) return zfcp_scsi_schedule_rport_register() port->rport_task = RPORT_ADD queue_work(rport_work) zfcp_scsi_rport_work() (port->rport_task == RPORT_ADD) port->rport_task = RPORT_NONE zfcp_scsi_rport_register() (port->rport == NULL) rport = fc_remote_port_add() port->rport = rport; Now the rport was erroneously unblocked while the zfcp_port is blocked. This is another situation we want to avoid due to scsi_eh potential. This state would at least remain until the new recovery from the other context finished successfully, or potentially forever if it failed. In order to close this race, we take the erp_lock inside zfcp_erp_try_rport_unblock() when checking the status of zfcp_port or LUN. With that, the possible corresponding rport state sequences would be: (unblock[ERP thread],block[other context]) if the ERP thread gets erp_lock first and still sees ((port->status & ...UNBLOCK) != 0), (block[other context],NOP[ERP thread]) if the ERP thread gets erp_lock after the other context has already cleard ...UNBLOCK from port->status. Since checking fields of struct erp_action is unsafe because they could have been overwritten (re-used for new recovery) meanwhile, we only check status of zfcp_port and LUN since these are only changed under erp_lock elsewhere. Regarding the check of the proper status flags (port or port_forced are similar to the shown adapter recovery): [zfcp_erp_adapter_shutdown()] zfcp_erp_adapter_reopen() zfcp_erp_adapter_block() * clear UNBLOCK ---------------------------------------+ zfcp_scsi_schedule_rports_block() | write_lock_irqsave(&adapter->erp_lock, flags);-------+ | zfcp_erp_action_enqueue() | | zfcp_erp_setup_act() | | * set ERP_INUSE -----------------------------------|--|--+ write_unlock_irqrestore(&adapter->erp_lock, flags);--+ | | .context-switch. | | zfcp_erp_thread() | | zfcp_erp_strategy() | | write_lock_irqsave(&adapter->erp_lock, flags);------+ | | ... | | | zfcp_erp_strategy_check_target() | | | zfcp_erp_strategy_check_adapter() | | | zfcp_erp_adapter_unblock() | | | * set UNBLOCK -----------------------------------|--+ | zfcp_erp_action_dequeue() | | * clear ERP_INUSE ---------------------------------|-----+ ... | write_unlock_irqrestore(&adapter->erp_lock, flags);-+ Hence, we should check for both UNBLOCK and ERP_INUSE because they are interleaved. Also we need to explicitly check ERP_FAILED for the link down case which currently does not clear the UNBLOCK flag in zfcp_fsf_link_down_info_eval(). Signed-off-by:
Steffen Maier <maier@linux.vnet.ibm.com> Fixes: 8830271c ("[SCSI] zfcp: Dont fail SCSI commands when transitioning to blocked fc_rport") Fixes: a2fa0aed ("[SCSI] zfcp: Block FC transport rports early on errors") Fixes: 5f852be9 ("[SCSI] zfcp: Fix deadlock between zfcp ERP and SCSI") Fixes: 338151e0 ("[SCSI] zfcp: make use of fc_remote_port_delete when target port is unavailable") Fixes: 3859f6a2 ("[PATCH] zfcp: add rports to enable scsi_add_device to work again") Reviewed-by:
Benjamin Block <bblock@linux.vnet.ibm.com> Signed-off-by:
-
Steffen Maier authored
commit 56d23ed7 upstream. Since quite a while, Linux issues enough SCSI commands per scsi_device which successfully return with FCP_RESID_UNDER, FSF_FCP_RSP_AVAILABLE, and SAM_STAT_GOOD. This floods the HBA trace area and we cannot see other and important HBA trace records long enough. Therefore, do not trace HBA response errors for pure benign residual under counts at the default trace level. This excludes benign residual under count combined with other validity bits set in FCP_RSP_IU, such as FCP_SNS_LEN_VAL. For all those other cases, we still do want to see both the HBA record and the corresponding SCSI record by default. Signed-off-by:
-
Benjamin Block authored
commit dac37e15 upstream. When SCSI EH invokes zFCP's callbacks for eh_device_reset_handler() and eh_target_reset_handler(), it expects us to relent the ownership over the given scsi_cmnd and all other scsi_cmnds within the same scope - LUN or target - when returning with SUCCESS from the callback ('release' them). SCSI EH can then reuse those commands. We did not follow this rule to release commands upon SUCCESS; and if later a reply arrived for one of those supposed to be released commands, we would still make use of the scsi_cmnd in our ingress tasklet. This will at least result in undefined behavior or a kernel panic because of a wrong kernel pointer dereference. To fix this, we NULLify all pointers to scsi_cmnds (struct zfcp_fsf_req *)->data in the matching scope if a TMF was successful. This is done under the locks (struct zfcp_adapter *)->abort_lock and (struct zfcp_reqlist *)->lock to prevent the requests from being removed from the request-hashtable, and the ingress tasklet from making use of the scsi_cmnd-pointer in zfcp_fsf_fcp_cmnd_handler(). For cases where a reply arrives during SCSI EH, but before we get a chance to NULLify the pointer - but before we return from the callback -, we assume that the code is protected from races via the CAS operation in blk_complete_request() that is called in scsi_done(). The following stacktrace shows an example for a crash resulting from the previous behavior: Unable to handle kernel pointer dereference at virtual kernel address fffffee17a672000 Oops: 0038 [#1] SMP CPU: 2 PID: 0 Comm: swapper/2 Not tainted task: 00000003f7ff5be0 ti: 00000003f3d38000 task.ti: 00000003f3d38000 Krnl PSW : 0404d00180000000 00000000001156b0 (smp_vcpu_scheduled+0x18/0x40) R:0 T:1 IO:0 EX:0 Key:0 M:1 W:0 P:0 AS:3 CC:1 PM:0 EA:3 Krnl GPRS: 000000200000007e 0000000000000000 fffffee17a671fd8 0000000300000015 ffffffff80000000 00000000005dfde8 07000003f7f80e00 000000004fa4e800 000000036ce8d8f8 000000036ce8d9c0 00000003ece8fe00 ffffffff969c9e93 00000003fffffffd 000000036ce8da10 00000000003bf134 00000003f3b07918 Krnl Code: 00000000001156a2: a7190000 lghi %r1,0 00000000001156a6: a7380015 lhi %r3,21 #00000000001156aa: e32050000008 ag %r2,0(%r5) >00000000001156b0: 482022b0 lh %r2,688(%r2) 00000000001156b4: ae123000 sigp %r1,%r2,0(%r3) 00000000001156b8: b2220020 ipm %r2 00000000001156bc: 8820001c srl %r2,28 00000000001156c0: c02700000001 xilf %r2,1 Call Trace: ([<0000000000000000>] 0x0) [<000003ff807bdb8e>] zfcp_fsf_fcp_cmnd_handler+0x3de/0x490 [zfcp] [<000003ff807be30a>] zfcp_fsf_req_complete+0x252/0x800 [zfcp] [<000003ff807c0a48>] zfcp_fsf_reqid_check+0xe8/0x190 [zfcp] [<000003ff807c194e>] zfcp_qdio_int_resp+0x66/0x188 [zfcp] [<000003ff80440c64>] qdio_kick_handler+0xdc/0x310 [qdio] [<000003ff804463d0>] __tiqdio_inbound_processing+0xf8/0xcd8 [qdio] [<0000000000141fd4>] tasklet_action+0x9c/0x170 [<0000000000141550>] __do_softirq+0xe8/0x258 [<000000000010ce0a>] do_softirq+0xba/0xc0 [<000000000014187c>] irq_exit+0xc4/0xe8 [<000000000046b526>] do_IRQ+0x146/0x1d8 [<00000000005d6a3c>] io_return+0x0/0x8 [<00000000005d6422>] vtime_stop_cpu+0x4a/0xa0 ([<0000000000000000>] 0x0) [<0000000000103d8a>] arch_cpu_idle+0xa2/0xb0 [<0000000000197f94>] cpu_startup_entry+0x13c/0x1f8 [<0000000000114782>] smp_start_secondary+0xda/0xe8 [<00000000005d6efe>] restart_int_handler+0x56/0x6c [<0000000000000000>] 0x0 Last Breaking-Event-Address: [<00000000003bf12e>] arch_spin_lock_wait+0x56/0xb0 Suggested-by:
-
Kashyap Desai authored
scsi: megaraid_sas: Do not set MPI2_TYPE_CUDA for JBOD FP path for FW which does not support JBOD sequence map commit d5573584 upstream. Signed-off-by:
Sumit Saxena <sumit.saxena@broadcom.com> Reviewed-by:
Hannes Reinecke <hare@suse.com> Reviewed-by:
Tomas Henzl <thenzl@redhat.com> Signed-off-by:
-
Kashyap Desai authored
commit 18e1c7f6 upstream. For SRIOV enabled firmware, if there is a OCR(online controller reset) possibility driver set the convert flag to 1, which is not happening if there are outstanding commands even after 180 seconds. As driver does not set convert flag to 1 and still making the OCR to run, VF(Virtual function) driver is directly writing on to the register instead of waiting for 30 seconds. Setting convert flag to 1 will cause VF driver will wait for 30 secs before going for reset. Signed-off-by:
Kiran Kumar Kasturi <kiran-kumar.kasturi@broadcom.com> Signed-off-by:
-
Maciej S. Szmigiero authored
commit 31b5929d upstream. There is a disagreement between drivers/tty/vt/keyboard.c and drivers/input/input-leds.c with regard to what is a Scroll Lock LED trigger name: input calls it "kbd-scrolllock", but vt calls it "kbd-scrollock" (two l's). This prevents Scroll Lock LED trigger from binding to this LED by default. Since it is a scroLL Lock LED, this interface was introduced only about a year ago and in an Internet search people seem to reference this trigger only to set it to this LED let's simply rename it to "kbd-scrolllock". Also, it looks like this was supposed to be changed before this code was merged: https://lkml.org/lkml/2015/6/9/697 but it was done only on the input side. Signed-off-by:
Maciej S. Szmigiero <mail@maciej.szmigiero.name> Acked-by:
Samuel Thibault <samuel.thibault@ens-lyon.org> Signed-off-by:
-
Rabin Vincent authored
commit af309226 upstream. If a block device is closed while iterate_bdevs() is handling it, the following NULL pointer dereference occurs because bdev->b_disk is NULL in bdev_get_queue(), which is called from blk_get_backing_dev_info() (in turn called by the mapping_cap_writeback_dirty() call in __filemap_fdatawrite_range()): BUG: unable to handle kernel NULL pointer dereference at 0000000000000508 IP: [<ffffffff81314790>] blk_get_backing_dev_info+0x10/0x20 PGD 9e62067 PUD 9ee8067 PMD 0 Oops: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC Modules linked in: CPU: 1 PID: 2422 Comm: sync Not tainted 4.5.0-rc7+ #400 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996) task: ffff880009f4d700 ti: ffff880009f5c000 task.ti: ffff880009f5c000 RIP: 0010:[<ffffffff81314790>] [<ffffffff81314790>] blk_get_backing_dev_info+0x10/0x20 RSP: 0018:ffff880009f5fe68 EFLAGS: 00010246 RAX: 0000000000000000 RBX: ffff88000ec17a38 RCX: ffffffff81a4e940 RDX: 7fffffffffffffff RSI: 0000000000000000 RDI: ffff88000ec176c0 RBP: ffff880009f5fe68 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000001 R11: 0000000000000000 R12: ffff88000ec17860 R13: ffffffff811b25c0 R14: ffff88000ec178e0 R15: ffff88000ec17a38 FS: 00007faee505d700(0000) GS:ffff88000fb00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b CR2: 0000000000000508 CR3: 0000000009e8a000 CR4: 00000000000006e0 Stack: ffff880009f5feb8 ffffffff8112e7f5 0000000000000000 7fffffffffffffff 0000000000000000 0000000000000000 7fffffffffffffff 0000000000000001 ffff88000ec178e0 ffff88000ec17860 ffff880009f5fec8 ffffffff8112e81f Call Trace: [<ffffffff8112e7f5>] __filemap_fdatawrite_range+0x85/0x90 [<ffffffff8112e81f>] filemap_fdatawrite+0x1f/0x30 [<ffffffff811b25d6>] fdatawrite_one_bdev+0x16/0x20 [<ffffffff811bc402>] iterate_bdevs+0xf2/0x130 [<ffffffff811b2763>] sys_sync+0x63/0x90 [<ffffffff815d4272>] entry_SYSCALL_64_fastpath+0x12/0x76 Code: 0f 1f 44 00 00 48 8b 87 f0 00 00 00 55 48 89 e5 <48> 8b 80 08 05 00 00 5d RIP [<ffffffff81314790>] blk_get_backing_dev_info+0x10/0x20 RSP <ffff880009f5fe68> CR2: 0000000000000508 ---[ end trace 2487336ceb3de62d ]--- The crash is easily reproducible by running the following command, if an msleep(100) is inserted before the call to func() in iterate_devs(): while :; do head -c1 /dev/nullb0; done > /dev/null & while :; do sync; done Fix it by holding the bd_mutex across the func() call and only calling func() if the bdev is opened. Fixes: 5c0d6b60 ("vfs: Create function for iterating over block devices") Reported-and-tested-by:
Rabin Vincent <rabinv@axis.com> Signed-off-by:
Jan Kara <jack@suse.cz> Reviewed-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
Jens Axboe <axboe@fb.com> Signed-off-by:
-
Alexander Usyskin authored
commit d5f8e166 upstream. pm_runtime_autosuspend can take synchronous or asynchronous paths, Because we are calling pm_runtime_mark_last_busy just before this most of the cases it takes the asynchronous way. However, when the FW or driver resets during already running runtime suspend, the call will result in calling to the driver's rpm callback and results in a deadlock on device_lock. The simplest fix is to replace pm_runtime_autosuspend with asynchronous pm_request_autosuspend. Signed-off-by:
Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by:
Tomas Winkler <tomas.winkler@intel.com> Signed-off-by:
-
Russell Currey authored
commit 298360af upstream. ast_get_dram_info() configures a window in order to access BMC memory. A BMC register can be configured to disallow this, and if so, causes an infinite loop in the ast driver which renders the system unusable. Fix this by erroring out if an error is detected. On powerpc systems with EEH, this leads to the device being fenced and the system continuing to operate. Signed-off-by:
Russell Currey <ruscur@russell.cc> Reviewed-by:
Joel Stanley <joel@jms.id.au> Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/20161215051241.20815-1-ruscur@russell.ccSigned-off-by:
-
Patrik Jakobsson authored
commit 0a97c81a upstream. Hook up drm_compat_ioctl to support 32-bit userspace on 64-bit kernels. It turns out that N2600 and N2800 comes with 64-bit enabled. We previously assumed there where no such systems out there. Signed-off-by:
Patrik Jakobsson <patrik.r.jakobsson@gmail.com> Signed-off-by:
Sean Paul <seanpaul@chromium.org> Link: http://patchwork.freedesktop.org/patch/msgid/20161101144315.2955-1-patrik.r.jakobsson@gmail.comSigned-off-by:
-
Alex Deucher authored
commit 8729675c upstream. New variant. Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Michel Dänzer authored
commit 6b16cf77 upstream. Fixes hangs in that case under some circumstances. v2: * Only use non-0 x/yorigin if the cursor is (partially) outside of the top/left edge of the total surface with AVIVO/DCE Bugzilla: https://bugzilla.suse.com/show_bug.cgi?id=1000433Signed-off-by:
Michel Dänzer <michel.daenzer@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> (v1) Signed-off-by:
-
Michel Dänzer authored
commit dcab0fa6 upstream. The cursor size also affects the register programming. Signed-off-by:
-
Ben Skeggs authored
commit 5b3800a6 upstream. DPAUX registers moved on Kepler, these chipsets were still using the Fermi implementation for some reason. This fixes detection of hotplug/sink IRQs on DP connectors. Signed-off-by:
Ben Skeggs <bskeggs@redhat.com> Signed-off-by:
-
Ben Skeggs authored
commit b27add13 upstream. This avoids an issue that occurs when we're attempting to preempt multiple channels simultaneously. HW seems to ignore preempt requests while it's still processing a previous one, which, well, makes sense. Fixes random "fifo: SCHED_ERROR 0d []" + GPCCS page faults during parallel piglit runs on (at least) GM107. Signed-off-by:
-
Ben Skeggs authored
commit f4e65efc upstream. Signed-off-by:
-
Ben Skeggs authored
commit 5dc7f4aa upstream. Signed-off-by:
-
Ben Skeggs authored
commit 768e8477 upstream. Signed-off-by:
-
