- 02 Feb, 2015 25 commits
-
-
Philipp Zabel authored
Now that the bitstream buffer is only allocated for the BIT decoder case, we can use bitstream.size to check for bitstream ringbuffer operation. Signed-off-by:
Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by:
Kamil Debski <k.debski@samsung.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-
Philipp Zabel authored
The BIT encoder does not use a per-context bitstream ringbuffer as it encodes directly into the videobuf2 capture queue's buffers. Avoid allocation of the bitstream ringbuffer for encoder contexts. Signed-off-by:
-
Philipp Zabel authored
In preparation for CODA9 JPEG support, allow contexts that control hardware units directly, without the BIT processor. Signed-off-by:
-
Philipp Zabel authored
Make sure the buffer_mutex lock is taken in coda_bit_release while coda_free_framebuffers and coda_free_context_buffers are called. Signed-off-by:
-
Philipp Zabel authored
In preparation for CODA9 JPEG support, which doesn't have to call SEQ_END on the BIT processor. Signed-off-by:
-
Philipp Zabel authored
Since we have to copy from input buffers into the bitstream ringbuffer with the CPU, there is no need for contiguous DMA buffers on the decoder input side. Signed-off-by:
-
Philipp Zabel authored
Call coda_estimate_sizeimage from both try_fmt and set_defaults to avoid this v4l2-compliance warning on the h.264 decoder video device: G_FMT: 1920x1088, 32315559, 1, 1920, 1048576, 3, 0, 0, feedcafe TRY/S_FMT: 1920x1088, 32315559, 1, 1920, 3133440, 3, 0, 0, feedcafe fail: v4l2-test-formats.cpp(948): Video Capture: S_FMT(G_FMT) != G_FMT Signed-off-by: -
Philipp Zabel authored
On i.MX6, two subsampling ping-pong buffers are used for motion estimation and deblocking They should not be counted as framebuffers, or they will be also used to store reconstructed frames, causing visible artifacts in P-frames. Signed-off-by:
-
Philipp Zabel authored
This patch queues seq_end_work and flushes the queue during stop_streaming and clears the ctx->initialized flag. This allows to start streaming again after stopping streaming without releasing the context. Signed-off-by:
-
Philipp Zabel authored
The isequence counter is never used, qsequence counts the buffers queued into the bit decoder bitstream ringbuffer. It needs to be reset in stop_streaming. Signed-off-by:
-
Markus Pargmann authored
Compare rounded up width to fit into bytesperline. Signed-off-by:
Markus Pargmann <mpa@pengutronix.de> Signed-off-by:
-
Philipp Zabel authored
To make sure a set RET_DEC_PIC_SUCCESS flag is not a leftover from a previous successful run, clear it in prepare_decode. Signed-off-by:
-
Philipp Zabel authored
Zeroing the SRAM on probe helps with debugging SRAM contents. Signed-off-by:
-
Philipp Zabel authored
Properly zero the structure on the stack before using it. Signed-off-by:
-
Philipp Zabel authored
v4l2-compliance complains about invalid colorspace settings being accepted on the output side. This patch only allows REC709 and JPEG. Signed-off-by:
-
Philipp Zabel authored
Clarify whether job_ready returns false because the context is on hold, waiting for new input buffers, whether there are not enough input buffers to fill two into the bitstream, or whether there is not enough data in the bitstream buffer for the bitstream reader hardware to read a whole frame. Signed-off-by:
-
Lucas Stach authored
If userspace doesn't properly separate the bitstream input into individual frames (which may happen for example on slightly corrupted streams) the CODA hardware may decode more frames than we expect. We already log an error in this case, but it's also necessary to adjust the sequence offset. Otherwise we spam the log with a sequence number mismatch on every frame frame after the unexpected one. Signed-off-by:
Lucas Stach <l.stach@pengutronix.de> Signed-off-by:
-
Philipp Zabel authored
Handle an empty buffer metadata list without crashing. This can happen if the decoder is fed a broken stream, or multiple compressed frames in a single queued buffer. Signed-off-by:
-
Philipp Zabel authored
Do not remove the per-context debugfs directory before the per-buffer debugfs entries contained therein. Signed-off-by:
-
Philipp Zabel authored
This patch fixes the ENC_SEQ_RC_PARA initial delay and bitrate masks. These bit fields are 15 bit wide, not 7 bit. Signed-off-by:
-
Fabian Frederick authored
Based on versioncheck. Signed-off-by:
Fabian Frederick <fabf@skynet.be> Signed-off-by:
-
Fabian Frederick authored
Based on versioncheck. Signed-off-by:
-
Nicolas Dufresne authored
The V4L2_CID_MPEG_MFC51_VIDEO_DECODER_H264_DISPLAY_DELAY_ENABLE control is a boolean but was documented as a integer. The documentation was also slightly miss-leading. Signed-off-by:
Nicolas Dufresne <nicolas.dufresne@collabora.com> Acked-by:
-
Nicolas Dufresne authored
The decoder should handle V4L2_DEC_CMD_STOP to trigger drain, but it currently expecting V4L2_ENC_CMD_STOP. Signed-off-by:
-
Nicolas Dufresne authored
The MFC driver has two controls, DISPLAY_DELAY and DISPLAY_DELAY_ENABLE that allow forcing the decoder to return a decoded frame sooner regardless of the order. The added support for firmware version 6 and higher was not taking into account the DISPLAY_DELAY_ENABLE boolean. Instead it had a comment stating that DISPLAY_DELAY should be set to a negative value to disable it. This is not possible since the control range is from 0 to 65535. This feature was also supposed to be disabled by default in order to produce frames in display order. Signed-off-by:
-
- 29 Jan, 2015 15 commits
-
-
Hans Verkuil authored
Remove obsolete text files for drivers that have been removed. Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
-
Hans Verkuil authored
These drivers haven't been tested in a long, long time. The hardware is ancient and hopelessly obsolete. These drivers also need to be converted to newer media frameworks but due to the lack of hardware that's going to be impossible. In addition, cheaper and vastly better hardware is available today. These drivers are already deprecated, so now remove them altogether. Signed-off-by:
-
Hans Verkuil authored
These drivers haven't been tested in a long, long time. The hardware is ancient and hopelessly obsolete. These drivers also need to be converted to newer media frameworks but due to the lack of hardware that's going to be impossible. So these drivers are a prime candidate for removal. If someone is interested in working on these drivers to prevent their removal, then please contact the linux-media mailinglist. These drivers are already deprecated, so now remove them altogether. Signed-off-by:
-
Hans Verkuil authored
This driver hasn't been tested in a long, long time. The company that made this chip has gone bust many years ago and hardware using this chip is next to impossible to find. This driver needs to be converted to newer media frameworks but due to the lack of hardware that's going to be impossible. Since cheap alternatives are easily available, there is little point in keeping this driver alive. This driver is already deprecated, so now remove it altogether. Signed-off-by:
-
Antti Palosaari authored
Rename firmware variable from fw_file to fw_name and change its type from u8 to const char as request_firmware() input is. Signed-off-by:
Antti Palosaari <crope@iki.fi> Signed-off-by:
-
Antti Palosaari authored
Print chip version once using log level into when init() is called. Remove cold/warm state printing as those are not very useful. Signed-off-by:
-
Antti Palosaari authored
Firmware version could be printed similarly than si2168 driver does. Signed-off-by:
-
Antti Palosaari authored
Use own goto label for error case mem free is needed, even kfree could be called with NULL. I think it is better to have it, even not required. Signed-off-by:
-
Antti Palosaari authored
- Rename ID table. - Remove magic numbers from ID table driver data field. Signed-off-by:
-
Antti Palosaari authored
Rename firmare download error path goto label. Remove firmware NULL set as NULL value is not needed anymore, due to recent change which started using goto labels for firmware error handling. Cc: Olli Salonen <olli.salonen@iki.fi> Signed-off-by:
-
Antti Palosaari authored
Carry struct i2c_client pointer in tuner_priv. This driver is I2C driver, which is represented as a struct i2c_client, so better to carry this top level structure for each routine in order to unify things. Signed-off-by:
-
Antti Palosaari authored
Remove if () from firmware command error path as there should not be any error prone conditional logic there. Use goto labels instead. Signed-off-by:
-
Antti Palosaari authored
'dev' is likely most common name in kernel for structure containing device state instance, so rename it in order to keep things consistent. Signed-off-by:
-
Antti Palosaari authored
Rename firmware variable from fw_file to fw_name and change its type from u8 to const char as request_firmware() input defines. Signed-off-by:
-
Antti Palosaari authored
Print chip version once using log level into when init() is called. Remove cold/warm state printing as those are not very useful. old printing: si2168 6-0064: found a 'Silicon Labs Si2168' in cold state si2168 6-0064: downloading firmware from file 'dvb-demod-si2168-b40-01.fw' si2168 6-0064: firmware version: 4.0.11 si2168 6-0064: found a 'Silicon Labs Si2168' in warm state new printing: si2168 6-0064: found a 'Silicon Labs Si2168-B40' si2168 6-0064: downloading firmware from file 'dvb-demod-si2168-b40-01.fw' si2168 6-0064: firmware version: 4.0.11 Signed-off-by:
-
