- 09 May, 2023 6 commits
-
-
Aloka Dixit authored
Security parameters for each non-transmitting profile can be different when MBSSID is enabled and this information is included in the MBSSID element in the Beacon frame. Current implementation to set rsnie_present and wpaie_present does not parse this element hence it applies only to the transmitting interface. Move the code to a separate function to make additions for non-transmitting interfaces cleaner. Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1 Signed-off-by:
Aloka Dixit <quic_alokad@quicinc.com> Signed-off-by:
Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20230405221648.17950-6-quic_alokad@quicinc.com
-
Aloka Dixit authored
Include MBSSID parameters in WMI vdev up operation. Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1 Signed-off-by:
John Crispin <john@phrozen.org> Signed-off-by:
-
Aloka Dixit authored
Rename trans_bssid to tx_vdev_bssid to make it similar to vdev_bssid. Rename profile_num to nontx_profile_cnt, and profile_idx to nontx_profile_idx which makes it clear that these store configurations related to MBSSID non-transmitting profiles. Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1 Signed-off-by:
-
Aloka Dixit authored
Configure multiple BSSID flags and index of the transmitting interface in vdev create/start commands depending on the service bit WMI_TLV_SERVICE_MBSS_PARAM_IN_VDEV_START_SUPPORT. Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1 Signed-off-by:
-
Aloka Dixit authored
Advertise the driver support for multiple BSSID (MBSSID) and enhanced multi-BSSID advertisements (EMA) by setting extended capabilities. Configure mbssid_max_interfaces and ema_max_profile_periodicity fields in structure wiphy which are used to advertise maximum number of interfaces and profile periodicity supported by the driver. Add new WMI fields to configure maximum vdev count supported for MBSSID and profile periodicity in case of EMA. Setting WMI_RSRC_CFG_FLAG2_CALC_NEXT_DTIM_COUNT_SET flag indicates that the firmware should track and update the DTIM counts for each non-transmitted profile. Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1 Signed-off-by:
-
Arnd Bergmann authored
In a rare arm64 randconfig build, I got multiple warnings for ath11k and ath12k: In function 'ath11k_peer_assoc_h_ht', inlined from 'ath11k_peer_assoc_prepare' at drivers/net/wireless/ath/ath11k/mac.c:2665:2: drivers/net/wireless/ath/ath11k/mac.c:1709:13: error: 'ath11k_peer_assoc_h_ht_masked' reading 10 bytes from a region of size 0 [-Werror=stringop-overread] 1709 | if (ath11k_peer_assoc_h_ht_masked(ht_mcs_mask)) | ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ This happens whenever gcc-13 fails to inline one of the functions that take a fixed-length array argument but gets passed a pointer. Change these functions to all take a regular pointer argument instead. Signed-off-by:Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
- 05 May, 2023 5 commits
-
-
Christophe JAILLET authored
ath11k_wmi_fw_stats_num_vdevs() and ath11k_wmi_fw_stats_num_bcn() really look the same as list_count_nodes(), so use the latter instead of hand writing it. The first ones use list_for_each_entry() and the other list_for_each(), but they both count the number of nodes in the list. While at it, also remove to prototypes of non-existent functions. Based on the names and prototypes, it is likely that they should be equivalent to list_count_nodes(). Compile tested only. Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by:
Simon Horman <simon.horman@corigine.com> Signed-off-by:
-
Christophe JAILLET authored
ath10k_wmi_fw_stats_num_peers() and ath10k_wmi_fw_stats_num_vdevs() really look the same as list_count_nodes(), so use the latter instead of hand writing it. The first ones use list_for_each_entry() and the other list_for_each(), but they both count the number of nodes in the list. Compile tested only. Signed-off-by:
-
Alexander Wetzel authored
Serialize the ath10k implementation of the wake_tx_queue ops. ath10k_mac_op_wake_tx_queue() must not run concurrent since it's using ieee80211_txq_schedule_start(). The intend of this patch is to sort out an issue discovered in the discussion referred to by the Link tag. I can't test it with real hardware and thus just implemented the per-ac queue lock Felix suggested. One obvious alternative to the per-ac lock would be to bring back the txqs_lock commit bb2edb73 ("ath10k: migrate to mac80211 txq scheduling") dropped. Fixes: bb2edb73 ("ath10k: migrate to mac80211 txq scheduling") Reported-by:
Felix Fietkau <nbd@nbd.name> Link: https://lore.kernel.org/r/519b5bb9-8899-ae7c-4eff-f3116cdfdb56@nbd.name CC: <stable@vger.kernel.org> Signed-off-by:
Alexander Wetzel <alexander@wetzel-home.de> Signed-off-by:
-
Karthik M authored
During stress test with maximum VAPs and peer connected, below warning is seen: [ 1079.110967] ath12k_pci 0004:01:00.0: mgmt tx queue is full [ 1079.117708] ath12k_pci 0004:01:00.0: failed to queue management frame -28 [ 1079.123191] ath12k_pci 0004:01:00.0: mgmt tx queue is full [ 1079.129960] ath12k_pci 0004:01:00.0: failed to queue management frame -28 [ 1079.135641] ath12k_pci 0004:01:00.0: mgmt tx queue is full This is caused by potential race condition while accessing skb_queue_len(). When ath12k_mgmt_over_wmi_tx_work() and ath12k_mac_mgmt_tx() is called concurrently, then skb_queue_len() might fetch list length which is modified by skb_queue_tail() or skb_dequeue(). Replace skb_queue_len() with skb_queue_len_lockless() which will prevent concurrent modified access using READ_ONCE(). And also use '>=', in case we queue a few SKBs simultaneously. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Signed-off-by:
Karthik M <quic_karm@quicinc.com> Signed-off-by:
Ramya Gnanasekar <quic_rgnanase@quicinc.com> Signed-off-by:
-
Karthik M authored
Transmission of management packets are done in a work queue. Sometimes the workqueue does not finish Tx immediately, then it lead after the next step of vdev delete finished, it start to send the management packet to firmware and lead firmware crash. ieee80211_set_disassoc() have logic of ieee80211_flush_queues() after it send_deauth_disassoc() to ath12k, its purpose is make sure the deauth was actually sent, so it need to change ath12k to match the purpose of mac80211. To address these issues wait for Tx management as well as Tx data packets. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Signed-off-by:
-
- 28 Apr, 2023 4 commits
-
-
Maxime Bizon authored
Because of what seems to be a typo, a 6Ghz-only phy for which the BDF does not allow the 7115Mhz channel will fail to register: WARNING: CPU: 2 PID: 106 at net/wireless/core.c:907 wiphy_register+0x914/0x954 Modules linked in: ath11k_pci sbsa_gwdt CPU: 2 PID: 106 Comm: kworker/u8:5 Not tainted 6.3.0-rc7-next-20230418-00549-g1e096a17625a-dirty #9 Hardware name: Freebox V7R Board (DT) Workqueue: ath11k_qmi_driver_event ath11k_qmi_driver_event_work pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : wiphy_register+0x914/0x954 lr : ieee80211_register_hw+0x67c/0xc10 sp : ffffff800b123aa0 x29: ffffff800b123aa0 x28: 0000000000000000 x27: 0000000000000000 x26: 0000000000000000 x25: 0000000000000006 x24: ffffffc008d51418 x23: ffffffc008cb0838 x22: ffffff80176c2460 x21: 0000000000000168 x20: ffffff80176c0000 x19: ffffff80176c03e0 x18: 0000000000000014 x17: 00000000cbef338c x16: 00000000d2a26f21 x15: 00000000ad6bb85f x14: 0000000000000020 x13: 0000000000000020 x12: 00000000ffffffbd x11: 0000000000000208 x10: 00000000fffffdf7 x9 : ffffffc009394718 x8 : ffffff80176c0528 x7 : 000000007fffffff x6 : 0000000000000006 x5 : 0000000000000005 x4 : ffffff800b304284 x3 : ffffff800b304284 x2 : ffffff800b304d98 x1 : 0000000000000000 x0 : 0000000000000000 Call trace: wiphy_register+0x914/0x954 ieee80211_register_hw+0x67c/0xc10 ath11k_mac_register+0x7c4/0xe10 ath11k_core_qmi_firmware_ready+0x1f4/0x570 ath11k_qmi_driver_event_work+0x198/0x590 process_one_work+0x1b8/0x328 worker_thread+0x6c/0x414 kthread+0x100/0x104 ret_from_fork+0x10/0x20 ---[ end trace 0000000000000000 ]--- ath11k_pci 0002:01:00.0: ieee80211 registration failed: -22 ath11k_pci 0002:01:00.0: failed register the radio with mac80211: -22 ath11k_pci 0002:01:00.0: failed to create pdev core: -22 Signed-off-by:
Maxime Bizon <mbizon@freebox.fr> Signed-off-by:
-
Christophe JAILLET authored
ATH12K_HE_MCS_MAX = 11, so this test and the following one are the same. Remove the one with the hard coded 11 value. Signed-off-by:
-
Fedor Pchelkin authored
For the reasons also described in commit b383e8ab ("wifi: ath9k: avoid uninit memory read in ath9k_htc_rx_msg()"), ath9k_htc_rx_msg() should validate pkt_len before accessing the SKB. For example, the obtained SKB may have been badly constructed with pkt_len = 8. In this case, the SKB can only contain a valid htc_frame_hdr but after being processed in ath9k_htc_rx_msg() and passed to ath9k_wmi_ctrl_rx() endpoint RX handler, it is expected to have a WMI command header which should be located inside its data payload. Implement sanity checking inside ath9k_wmi_ctrl_rx(). Otherwise, uninit memory can be referenced. Tested on Qualcomm Atheros Communications AR9271 802.11n . Found by Linux Verification Center (linuxtesting.org) with Syzkaller. Fixes: fb9987d0 ("ath9k_htc: Support for AR9271 chipset.") Reported-and-tested-by: syzbot+f2cb6e0ffdb961921e4d@syzkaller.appspotmail.com Signed-off-by:
Fedor Pchelkin <pchelkin@ispras.ru> Acked-by:
Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by:
-
Peter Seiderer authored
Fix ath9k_hw_verify_hang()/ar9003_hw_detect_mac_hang() register offset calculation (do not overflow the shift for the second register/queues above five, use the register layout described in the comments above ath9k_hw_verify_hang() instead). Fixes: 222e0483 ("ath9k: Fix MAC HW hang check for AR9003") Reported-by:
Gregg Wonderly <greggwonderly@seqtechllc.com> Link: https://lore.kernel.org/linux-wireless/E3A9C354-0CB7-420C-ADEF-F0177FB722F4@seqtechllc.com/Signed-off-by:
Peter Seiderer <ps.report@gmx.net> Acked-by:
-
- 26 Apr, 2023 3 commits
-
-
Carl Huang authored
Low receive throughput is seen on WCN7850 because ADDBA related parameters are not updated to firmware when receive ADDBA session starts. Fix it by sending WMI_PEER_REORDER_QUEUE_SETUP_CMDID again to firmware to update the ADDBA related parameters for chips which have false reoq_lut_support in hw_params. For chips which have true reoq_lut_support in hw_params don't need this command to send to firmware. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Signed-off-by:
Carl Huang <quic_cjhuang@quicinc.com> Signed-off-by:
-
Carl Huang authored
The PCIe PERST pin is currently pulled down on WCN7850 and it causes some power leakage. Fix it by notifying firmware not to pull down PCIe PERST pin in QMI message for WCN7850. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Signed-off-by:
-
Carl Huang authored
Currently the CNSS (Connectivity Subsystem) QMI feature is assigned to qmi_wlanfw_host_cap_req_msg_v01 request directly, this prevents chip-specific CNSS features from being added easily. Solve this by adding a new field qmi_cnss_feature_bitmap to hw_params so chip-specific CNSS features can be assigned to this field and later assigned to qmi_wlanfw_host_cap_req_msg_v01 request. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Signed-off-by:
-
- 20 Apr, 2023 22 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.gitKalle Valo authored
ath.git patches for v6.4. Major changes: wcn36xx * support for pronto v3 hardware ath11k * PCIe DeviceTree bindings * WCN6750: enable SAR support ath10k * convert DeviceTree bindings to YAML
-
https://github.com/nbd168/wirelessKalle Valo authored
mt76 patches for 6.4 - fixes - connac code unification - mt7921 p2p support - mt7996 mesh a-msdu support - mt7996 eht support - mt7996 coredump support
-
Simon Horman authored
Update spelling in comments in main.h Found by inspection. Signed-off-by:
Simon Horman <horms@kernel.org> Reviewed-by:
Ping-Ke Shih <pkshih@realtek.com> Signed-off-by:
Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20230418-rtw88-starspell-v1-1-70e52a23979b@kernel.org
-
Arnd Bergmann authored
This driver does not actually use the ISA DMA API, it is purely PIO based, so remove the dependency. Signed-off-by:
-
Bitterblue Smith authored
The goal of writing 0x6954341e / 0x6955341e to REG_OFDM0_XA_AGC_CORE1 appears to be setting the initial gain, which is stored in bits 0..6. Bits 7..31 are the same as what the phy init tables write. Modify only bits 0..6 so that we don't have to care about the values of the others. This way we don't have to add another "else if" for the RTL8192FU. Why we need to change the initial gain from the default 0x20 to 0x1e? Not sure. Some of the vendor drivers change it to 0x1e before scanning and then restore it to the original value after. Signed-off-by:
Bitterblue Smith <rtl8821cerfe2@gmail.com> Reviewed-by:
-
Bitterblue Smith authored
Also add rtl8xxxu_write32_mask, rtl8xxxu_write_rfreg_mask. These helper functions make it easier to modify only parts of a register by eliminating the call to the register reading function and the bit manipulations. Signed-off-by:
-
Bitterblue Smith authored
Most devices have a vendor name, product name, and serial number in the efuse, but it's pretty useless. It duplicates the information already printed by the USB subsystem: usb 1-4: New USB device found, idVendor=0bda, idProduct=8178, bcdDevice= 2.00 usb 1-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3 usb 1-4: Product: 802.11n WLAN Adapter usb 1-4: Manufacturer: Realtek usb 1-4: SerialNumber: 00e04c000001 -> usb 1-4: Vendor: Realtek -> usb 1-4: Product: 802.11n WLAN Adapter usb 1-4: New USB device found, idVendor=0bda, idProduct=818b, bcdDevice= 2.00 usb 1-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3 usb 1-4: Product: 802.11n NIC usb 1-4: Manufacturer: Realtek usb 1-4: SerialNumber: 00e04c000001 -> usb 1-4: Vendor: Realtek -> usb 1-4: Product: 802.11n NIC -> usb 1-4: Serial not available. usb 1-4: New USB device found, idVendor=0bda, idProduct=f179, bcdDevice= 0.00 usb 1-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3 usb 1-4: Product: 802.11n usb 1-4: Manufacturer: Realtek usb 1-4: SerialNumber: 002E2DC0041F -> usb 1-4: Vendor: Realtek -> usb 1-4: Product: 802.11n usb 1-4: New USB device found, idVendor=0bda, idProduct=8179, bcdDevice= 0.00 usb 1-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3 usb 1-4: Product: 802.11n NIC usb 1-4: Manufacturer: Realtek usb 1-4: SerialNumber: 00E04C0001 -> usb 1-4: Vendor: Realtek -> usb 1-4: Product: 802.11n NIC -> usb 1-4: Serial: 00E04C0001 Also, that data is not interpreted correctly in all cases: usb 3-1.1.2: New USB device found, idVendor=0bda, idProduct=8179, bcdDevice= 0.00 usb 3-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 usb 3-1.1.2: Product: 802.11n NIC usb 3-1.1.2: Manufacturer: Realtek usb 3-1.1.2: Vendor: Realtek usb 3-1.1.2: Product: \x03802.11n NI usb 3-1.1.2: Serial: \xff\xff\xff\xff\xff\xff\xff\xff\xff\xff\xff Link: https://bugzilla.kernel.org/show_bug.cgi?id=217231Signed-off-by:
-
Larry Finger authored
Kmemleak shows the following leak arising from routine in the usb probe routine: unreferenced object 0xffff895cb29bba00 (size 512): comm "(udev-worker)", pid 534, jiffies 4294903932 (age 102751.088s) hex dump (first 32 bytes): 77 30 30 30 00 00 00 00 02 2f 2d 2b 30 00 00 00 w000...../-+0... 02 00 2a 28 00 00 00 00 ff 55 ff ff ff 00 00 00 ..*(.....U...... backtrace: [<ffffffff9265fa36>] kmalloc_trace+0x26/0x90 [<ffffffffc17eec41>] rtw_usb_probe+0x2f1/0x680 [rtw_usb] [<ffffffffc03e19fd>] usb_probe_interface+0xdd/0x2e0 [usbcore] [<ffffffff92b4f2fe>] really_probe+0x18e/0x3d0 [<ffffffff92b4f5b8>] __driver_probe_device+0x78/0x160 [<ffffffff92b4f6bf>] driver_probe_device+0x1f/0x90 [<ffffffff92b4f8df>] __driver_attach+0xbf/0x1b0 [<ffffffff92b4d350>] bus_for_each_dev+0x70/0xc0 [<ffffffff92b4e51e>] bus_add_driver+0x10e/0x210 [<ffffffff92b50935>] driver_register+0x55/0xf0 [<ffffffffc03e0708>] usb_register_driver+0x88/0x140 [usbcore] [<ffffffff92401153>] do_one_initcall+0x43/0x210 [<ffffffff9254f42a>] do_init_module+0x4a/0x200 [<ffffffff92551d1c>] __do_sys_finit_module+0xac/0x120 [<ffffffff92ee6626>] do_syscall_64+0x56/0x80 [<ffffffff9300006a>] entry_SYSCALL_64_after_hwframe+0x46/0xb0 The leak was verified to be real by unloading the driver, which resulted in a dangling pointer to the allocation. The allocated memory is freed in rtw_usb_intf_deinit(). Signed-off-by:Larry Finger <Larry.Finger@lwfinger.net> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Ping-Ke Shih <pkshih@realtek.com> Reviewed-by:
-
Sascha Hauer authored
We have to call rtw8821c_switch_rf_set() with SWITCH_TO_WLG or SWITCH_TO_BTG according to the chip variant as denoted in rfe_option. The information which argument to use for which variant has been taken from the vendor driver. Signed-off-by:
Sascha Hauer <s.hauer@pengutronix.de> Reviewed-by:
-
Sascha Hauer authored
According to the vendor driver the pkg_type has to be set to '1' for some rtw8821c variants. As the pkg_type has been hardcoded to '0', add a field for it in struct rtw_hal and set this correctly in the rtw8821c part. With this parsing of a rtw_table is influenced and check_positive() in phy.c returns true for some cases here. The same is done in the vendor driver. However, this has no visible effect on the driver here. Signed-off-by:
-
Sascha Hauer authored
On my RTW8821CU chipset rfe_option reads as 0x22. Looking at the vendor driver suggests that the field width of rfe_option is 5 bit, so rfe_option should be masked with 0x1f. Without this the rfe_option comparisons with 2 further down the driver evaluate as false when they should really evaluate as true. The effect is that 2G channels do not work. rfe_option is also used as an array index into rtw8821c_rfe_defs[]. rtw8821c_rfe_defs[34] (0x22) was added as part of adding USB support, likely because rfe_option reads as 0x22. As this now becomes 0x2, rtw8821c_rfe_defs[34] is no longer used and can be removed. Note that this might not be the whole truth. In the vendor driver there are indeed places where the unmasked rfe_option value is used. However, the driver has several places where rfe_option is tested with the pattern if (rfe_option == 2 || rfe_option == 0x22) or if (rfe_option == 4 || rfe_option == 0x24), so that rfe_option BIT(5) has no influence on the code path taken. We therefore mask BIT(5) out from rfe_option entirely until this assumption is proved wrong by some chip variant we do not know yet. Signed-off-by:
Alexandru gagniuc <mr.nuke.me@gmail.com> Tested-by:
ValdikSS <iam@valdikss.org.ru> Cc: stable@vger.kernel.org Reviewed-by:
-
Sascha Hauer authored
The RTW88 chipsets have four different priority queues in hardware. For the USB type chipsets the packets destined for a specific priority queue must be sent through the endpoint corresponding to the queue. This was not fully understood when porting from the RTW88 USB out of tree driver and thus violated. This patch implements the qsel to endpoint mapping as in get_usb_bulkout_id_88xx() in the downstream driver. Without this the driver often issues "timed out to flush queue 3" warnings and often TX stalls completely. Signed-off-by:
-
Po-Hao Huang authored
Allow 8822c to operate two interface concurrently, only 1 AP mode plus 1 station mode under same frequency is supported. Combination of other types will not be added until requested. Signed-off-by:
Po-Hao Huang <phhuang@realtek.com> Signed-off-by:
-
Po-Hao Huang authored
This patch allows vifs sharing same hardware with the AP mode vif to do scan, do note that this could lead to packet loss or disconnection of the AP's clients. Since we don't have chanctx, update scan info upon set channel so bandwidth changes won't go unnoticed and get misconfigured after scan. Download beacon just before scan starts to allow hardware to get proper content to do beaconing. Last, beacons should only be transmitted in AP's operating channel. Turn related beacon functions off while we're in other channels so the receiving stations won't get confused. Signed-off-by:
-
Po-Hao Huang authored
Only abort scan with current scanning VIF. If we have more than one interface, we could call rtw_hw_scan_abort() with the wrong VIF as input. This avoids potential null pointer being accessed when actually the other VIF is scanning. Signed-off-by:
-
Po-Hao Huang authored
Only gather reserved pages from AP interface after it has started. Or else ieee80211_beacon_get_*() returns NULL and causes other VIFs' reserved pages fail to download. Update location of current reserved page after beacon renews so offsets changed by beacon can be recognized. Signed-off-by:
-
Po-Hao Huang authored
Firmware can't support PS mode during AP mode, so disallow this case. Signed-off-by:
-
Po-Hao Huang authored
Extend 8822c's reserved page number to accommodate additional required pages. Reserved page is an area of memory in the FIFO dedicated for special purposes. Previously only one interface is supported so 8 pages should suffice, extend it so we can support 2 interfaces concurrently. Signed-off-by:
-
Po-Hao Huang authored
Switch port settings if AP mode does not start on port 0 because of hardware limitation. For some ICs, beacons on ports other than zero could misbehave and do not issue properly, to fix this we change AP VIFs to port zero when multiple interfaces is active. Signed-off-by:
-
Po-Hao Huang authored
In order to support multiple interfaces, multiple port settings will be required. Current code always uses port 0 and should be changed. Declare a bitmap with size equal to hardware port number to record the current usage. Signed-off-by:
-
Ping-Ke Shih authored
The function to request DLE (data link engine) buffer uses 'u16' as return value that mixes error code, so change it to 'int' as regular error code. Also, treat invalid register value (0xfff) as an error. Signed-off-by:
-
Yingsha Xu authored
Smatch complains that: debugfs_hw_add() warn: 'statsd' is an error pointer or valid Debugfs checks are generally not supposed to be checked for errors and it is not necessary here. Just delete the dead code. Signed-off-by:
Yingsha Xu <ysxu@hust.edu.cn> Reviewed-by:
Dongliang Mu <dzm91@hust.edu.cn> Link: https://lore.kernel.org/r/20230419104548.30124-1-ysxu@hust.edu.cnSigned-off-by:
Johannes Berg <johannes.berg@intel.com>
-
