UART3 pins are available in the J1003 connector.

Add support for it.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add new board based on the Toradex Verdin iMX8M Mini SoM, the MX8Menlo.
The board is a compatible replacement for i.MX53 M53Menlo and features
USB, multiple UARTs, ethernet, LEDs, SD and eMMC.
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Francesco Dolcini <francesco.dolcini@toradex.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: NXP Linux Team <linux-imx@nxp.com>
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The Gateworks GW7400 is an ARM based single board computer (SBC)
featuring:
 - i.MX8M Plus SoC
 - LPDDR4 DRAM
 - eMMC FLASH
 - Gateworks System Controller (GSC)
 - QOS GbE
 - Microchip GbE Switch
 - Multiple multi-protocol RS232/RS485/RS422 Serial ports
 - USB 3.0 Front panel connector
 - onboard 802.11ac WiFi / BT
 - 3x miniPCIe socket with PCIe and USB 2.0
 - 1x M.2 B/A-E socket with PCIe, USB 3.0 and dual nano-SIM sockets
 - off-board connectors for: MIPI DSI, MIPI CSI, SPI, GPIO, I2C
 - Wide range DC power input
 - Passive PoE
 - 802.3at PoE
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Krzysztof Kozlowski <krzk+dt@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add pwm1/backlight support nodes for imx8mm_evk board.
Align with u-boot dts

References:
 - https://patchwork.ozlabs.org/project/uboot/patch/20220326111911.13720-9-tommaso.merciai@amarulasolutions.com/Signed-off-by: Tommaso Merciai <tommaso.merciai@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add a device tree for the 8MNANOD3L-EVK eval board which features an
IMX8MN SoC. It is similar to the 8MNANODLPD4-EVK eval board except it
has an IMX8MN UltraLite SoC and DDR3L memory. It esp. differs in the
PMIC configuration because the SoC has a smaller package and thus the
ARM core voltage is combined with the SoC voltage and the DDR voltage
is 1.35V for the DDR3L memory.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add the missing 'uart-has-rtscts' property to UART's that have hardware
flow control capability.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add the Video Processing Unit node for IMX8Q SoC.
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Shijie Qin <shijie.qin@nxp.com>
Signed-off-by: Zhou Peng <eagle.zhou@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The SDHC controller in the imx8mp has the same controller
as the imx8mm which supports HS400-ES. Change the compatible
fallback to imx8mm to enable it, but keep the imx7d-usdhc
to prevent breaking backwards compatibility.
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The SDHC controller in the imx8mn has the same controller
as the imx8mm which supports HS400-ES. Change the compatible
fallback to imx8mm to enable it, but keep the imx7d-usdhc
to prevent breaking backwards compatibility.
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This patch adds the device tree to support Toradex Verdin iMX8M Plus [1]
a computer on module which can be used on different carrier boards.

The module consists of an NXP i.MX 8M Plus family SoC (either i.MX 8M
Plus Quad or 8M Plus QuadLite), a PCA9450C PMIC, a Gigabit Ethernet PHY,
1, 2, 4 or 8 GB of LPDDR4 RAM, an eMMC, a TLA2024 ADC, an I2C EEPROM, an
RX8130 RTC, an optional I2C temperature sensor plus an optional
Bluetooth/Wi-Fi module.

Anything that is not self-contained on the module is disabled by
default.

The device tree for the Dahlia includes the module's device tree and
enables the supported peripherals of the carrier board.

The device tree for the Verdin Development Board includes the module's
device tree as well as the Dahlia one as it is a superset and supports
almost all peripherals available.

So far there is no display functionality supported at all but basic
console UART, USB host, eMMC and Ethernet functionality work fine.

[1] https://www.toradex.com/computer-on-modules/verdin-arm-family/nxp-imx-8m-plusSigned-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add DMA properties to uart2 node.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The node names should be generic and SPI NOR dtschema expects "flash".
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

fsl,clk-source property is of type uint8 and need to be defined as
"/bits/ 8 <0>". Simply setting value to 0 raise warning:
can@2180000: fsl,clk-source:0: [0, 0, 0, 0] is too long
Signed-off-by: Kuldeep Singh <singh.kuldeep87k@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

At the moment, the dtsi will force the dr_mode to host. This is
problematic because it will always turn on the Vbus voltage regardless
if the port is host or device. This might lead to a "shortcut" between
the two USB endpoints because both might have their Vbus supplies
enabled. Therefore, the default should be "otg" for any ports which
aren't host only (from a SoC point of view) and have a user of the dtsi
file overwrite that explicitly.

Move the 'dr_mode = "host";' into the board dts. Now that the dtsi
doesn't set the dr_mode anymore, we can also drop the 'dr_mode = "otg";'
in the board dts because that is the default value if dr_mode is not
set.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Enable the ocelot-8021q tagger by default which supports ethernet flow
control.

The new default is set in the common board dtsi. The actual switch
node is enabled on a per board variant basis. Because of this we
set the new tagger default for both internal ports and a particular
variant is free to choose among the two port.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add SD1 sleep pinctrl to avoid backfeeding during sleep.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add a note about us using discrete external on-module resistors
pulling-up to the on-module +V3.3_1.8_SD (LDO5) rail and explicitly
disabling the internal pull-ups due to ERR050080 [1]:

IO: Degradation of internal IO pullup/pulldown current capability for
IO’s continuously driven in a 3.3V operating mode

[1] https://www.nxp.com/webapp/Download?colCode=IMX8MM_0N87WSigned-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Fix capitalisation of Verdin in comments.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Alphabetically re-order pinctrl groups.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Update IOMUX configuration as required by the hardware design team.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add a note about the bootloader being expected to switch on the I2C
level shifter for the TLA2024 ADC behind this PMIC.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Make sure we only have dashes rather than underscores in node names by
renaming ctrl_sleep_moci-hog to ctrl-sleep-moci-hog.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Alphabetically re-order nodes.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Fix multi-line comment style.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Annotate regulators which are on-module.
Rename usb_otg{1/2}_vbus to USB_{1/2}_EN more in-line with Verdin spec.
Annotate PMIC regulators with information on which BUCK/LDO they are on.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

i.MX8MP use synopsys V3.70a ddr controller IP, so add edac support
for i.MX8MP based on "snps,ddrc-3.80a" synopsys edac driver.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add A53 OPP table and cpu regulator to support cpu-freq driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Anson Huang <Anson.Huang@nxp.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: NXP Linux Team <linux-imx@nxp.com>
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

And missing speed grade phandle to cpu@0 node.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Anson Huang <Anson.Huang@nxp.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: NXP Linux Team <linux-imx@nxp.com>
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add the DT nodes for both the 3D and 2D GPU cores found on the i.MX8MP.

etnaviv-gpu 38000000.gpu: model: GC7000, revision: 6204
etnaviv-gpu 38008000.gpu: model: GC520, revision: 5341
[drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Tested-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add the power domains for the GPUs, which do not require any interaction with
a blk-ctrl, but are simply two PU domains nested inside a MIX domain.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

There is a 32MiB Micron MT25QU256ABA1 serial NOR flash on the EVK board.
Add a device tree node for it.

Tested on a 8MNANOD3L-EVK.
Signed-off-by: Michael Walle <michael@walle.cc>
Tested-by: Heiko Thiery <heiko.thiery@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The r4 ("Evergreen") hardware revision of the Librem 5 phone includes a
slightly different panel than the revisions before it. Since its'
description is available, describe it properly for the board.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This partition will hold a squashfs firmware jail. Only one read-only
partition is needed.
Signed-off-by: Angus Ainslie <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

1,5A is what's used by the type-c controller on the Librem 5 board so
increase ti,boost-max-current to 1,5A too.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

That pin is not connected on the board so no need to describe it.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

They turn on the display currently so to be consistent, let's make
them wake the system from suspend as well.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The i.MX8MQ PLL support hdmi phy 27m as pll reference clock,
so add a fixed clock for it.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Use the proper voltages as supported by the board instead of the ones
supported by the PMIC. The voltages were taken from both the schematic
of the 8MNANOLPD4-EVK eval board and the datasheet of the IMX8MN SoC.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Heiko Thiery <heiko.thiery@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Use the power signal names as given in the schematics of the reference
board.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The node name of Ethernet controller should be "ethernet" instead of
"usbether" as required by Ethernet controller devicetree schema:
 Documentation/devicetree/bindings/net/ethernet-controller.yaml

This patch can potentially affect boot loaders patching against full
node path instead of using device aliases.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>