Turns out that Tiger Lake GPIO will be enumerated using _HID method where
there is only a single ACPI device and multiple BARs so rework the driver
to support that scheme instead.

Fixes: c9ccf71f ("pinctrl: intel: Add Intel Tiger Lake pin controller support")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Intel Coffee Lake-S PCH has the same GPIO hardware than Sunrisepoint-H
PCH but the ACPI ID is different. Add this new ACPI ID to the list of
supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.

For chained irqchips this is a pretty straight-forward conversion.

Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

When IRQ chip is instantiated via GPIO library flow, the few functions,
in particular the ACPI event registration mechanism, on some of ACPI based
platforms expect that the pin ranges are initialized to that point.

Add GPIO <-> pin mapping ranges via callback in the GPIO library flow.

Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Suspending Goodix touchscreens requires changing the interrupt pin to
output before sending them a power-down command. Followed by wiggling
the interrupt pin to wake the device up, after which it is put back
in input mode.

On Cherry Trail device the interrupt pin is listed as a GpioInt ACPI
resource so we can do this without problems as long as we release the
IRQ before changing the pin to output mode.

On Bay Trail devices with a Goodix touchscreen direct-irq mode is used
in combination with listing the pin as a normal GpioIo resource. This
works fine, but this triggers the WARN in byt_gpio_set_direction-s output
path because direct-irq support is enabled on the pin.

This commit replaces the WARN call with a dev_info_once call, fixing a
bunch of WARN splats in dmesg on each suspend/resume cycle.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Suspending Goodix touchscreens requires changing the interrupt pin to
output before sending them a power-down command. Followed by wiggling
the interrupt pin to wake the device up, after which it is put back
in input mode.

On Bay Trail devices with a Goodix touchscreen direct-irq mode is used
in combination with listing the pin as a normal GpioIo resource.

This works fine, until the goodix driver gets rmmod-ed and then insmod-ed
again. In this case byt_gpio_disable_free() calls
byt_gpio_clear_triggering() which clears the IRQ flags and after that the
(direct) IRQ no longer triggers.

This commit fixes this by adding a check for the BYT_DIRECT_IRQ_EN flag
to byt_gpio_clear_triggering().

Note that byt_gpio_clear_triggering() only gets called from
byt_gpio_disable_free() for direct-irq enabled pins, as these are excluded
from the irq_valid mask by byt_init_irq_valid_mask().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Commit 179e5a61 ("pinctrl: intel: Remove default Interrupt Status
offset") removes default interrupt status offset of GPIO controllers,
with previous commits explicitly providing the previously default
offsets. However, the is_offset value in SPTH_COMMUNITY is missing,
preventing related irq from being properly detected and handled.

Fixes: f702e0b9 ("pinctrl: sunrisepoint: Provide Interrupt Status register offset")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=205745
Cc: stable@vger.kernel.org
Signed-off-by: Boyan Ding <boyan.j.ding@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Reflect in the driver that it is now a pin control one.

While here, update copyright years and authors.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>

When all preparations are done, we may switch to pin control API.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>

When IRQ chip is instantiated via GPIO library flow, the few functions,
in particular the ACPI event registration mechanism, on some of ACPI based
platforms expect that the pin ranges are initialized to that point.

Add GPIO <-> pin mapping ranges via callback in the GPIO library flow.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>

The introduced callback ->pin_dbg_show() is useful for debugging.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>

Add implementation for:
    - pin control, group information retrieval: count, name and pins
    - pin muxing:
      - function information (count, name and groups)
      - mux setting
      - GPIO control (enable, disable, set direction)
    - pin configuration:
      - pull disable, up and down
      - any other option is treated as not supported.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>

We may use now available struct intel_pinctrl in the driver.
No functional change implied.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>

In order to implement pin control for Intel Lynxpoint, we need
data structures in which to store and pass along pin, community
and SoC data information.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>

Allows querying GPIO direction from the pad config register.
If the pad is not in GPIO mode, return an error.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>

Instead of playing tricks with registers in the interrupt handler,
utilize the IRQ chip core for ACKing interrupts properly.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>

There is nothing wrong with requesting pin that owned by ACPI.
The only difference is how interrupt status will be reflected.
It means that in ACPI mode we may not use pin as GPIO-backed IRQ.

Taking above into consideration, move the check from GPIO to IRQ chip
callback.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>

Consolidate IRQ routines for better maintenance.

While here, rename lp_irq_type() to lp_irq_set_type() to be in align
with a callback name.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>

Consolidate ->remove and ->probe() callbacks for better maintenance.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>

We may need this function for other features in the pin control driver.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>

Simple type conversion with no functional change implied.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>

Convert driver to use memory mapped IO accessors.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>

There is no need to keep pointer to struct platform_device, which is container
of struct device, because the latter is what have been used everywhere outside
of ->probe() path. In any case we may derive pointer to the container when
needed.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>

A pin in native mode still can be requested as GPIO, though we assume
that firmware has configured it properly, which sometimes is not the case.

Here we allow turning the pin as GPIO to avoid potential issues,
but issue warning that something might be wrong.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>

New generations can use 2 bits for mode selector.
Update the code to support it.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>

The pattern
	foo = kmalloc(sizeof(*foo), GFP_KERNEL);
has an advantage when foo type is changed. Since we are planning a such,
better to be prepared by using standard pattern for memory allocation.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>

Replace explicit casting by pointer to struct resource with
specifier replacement to %pR to print the IO resource.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>

There is no need to assign ret variable in ->probe().
Drop useless assignment.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>

When we count from 0 it's possible to get into off-by-one error.
That's what had happened to this driver. So, correct amount of pins
and related typos in the code.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>

The Intel Lynxpoint pinctrl driver implements irqchip callbacks which are
called with desc->lock raw_spinlock held. In mainline this is fine because
spinlock resolves to raw_spinlock. However, running the same code in -rt
we will get a BUG() asserted.

This is because in -rt spinlocks are preemptible so taking the driver
private spinlock in irqchip callbacks causes might_sleep() to trigger.

In order to keep -rt happy but at the same time make sure that register
accesses get serialized, convert the driver to use raw_spinlock instead.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>

Move Lynxpoint GPIO driver under Intel pin control umbrella
for further transformation to a real pin control driver.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>

We may use now available struct intel_pinctrl in the driver.
No functional change implied.
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Use local variable to keep device pointer in order to increase readability
of the driver.
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

There is no need to keep pointer to struct platform_device, which is container
of struct device, because the latter is what have been used everywhere outside
of ->probe() path. In any case we may derive pointer to the container when
needed.
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

There are few drivers for Intel SoC GPIO which may utilize
the same data structure to describe this IP.

Share struct intel_pinctrl for wider user.
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Use new GPIO_LINE_DIRECTION_IN and GPIO_LINE_DIRECTION_OUT when
returning GPIO direction to GPIO framework.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>

Use new GPIO_LINE_DIRECTION_IN and GPIO_LINE_DIRECTION_OUT when
returning GPIO direction to GPIO framework.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>

Use new GPIO_LINE_DIRECTION_IN and GPIO_LINE_DIRECTION_OUT when
returning GPIO direction to GPIO framework.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

There is a logical continuation of the commit 5fbe5b58 ("gpio: Initialize
the irqchip valid_mask with a callback") to split IRQ initialization to
hardware and valid mask setup parts.
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

After commit 5ea422750a9f ("pinctrl: baytrail: Pass irqchip when
adding gpiochip") the GPIO IRQ chip structure is being initialized
under conditional when IRQ resource has been discovered. But that
commit left aside the assignment of ->init_valid_mask() callback
that is done unconditionally.

For sake of consistency and preventing some garbage in GPIO IRQ chip
structure group initialization together.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>