[ Upstream commit 2ab95749 ]

Initial discussion was:
[FYI] xfrm: Don't lookup sk_policy for timewait sockets

Forwarded frames should not have a socket attached. Especially
tw sockets will lead to panics later-on in the stack.

This was observed with TPROXY assigning a tw socket and broken
policy routing (misconfigured). As a result frame enters
forwarding path instead of input. We cannot solve this in
TPROXY as it cannot know that policy routing is broken.

v2:
Remove useless comment
Signed-off-by: Sebastian Poehn <sebastian.poehn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 8b01fc86 upstream.

This prevents a race between chown() and execve(), where chowning a
setuid-user binary to root would momentarily make the binary setuid
root.

This patch was mostly written by Linus Torvalds.
Signed-off-by: Jann Horn <jann@thejh.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d0311314 upstream.

The hardware and firmware for the RTL8192EE utilize a FIFO list of
descriptors. There were some problems with the initial implementation.
The worst of these failed to detect that the FIFO was becoming full,
which led to the device needing to be power cycled. As this condition
is not relevant to most of the devices supported by rtlwifi, a callback
routine was added to detect this situation. This patch implements the
necessary changes in the pci handler, and the linkage into the appropriate
rtl8192ee routine.
Signed-off-by: Troy Tan <troy_tan@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [V3.18]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit e66f17ff upstream.

We have a race condition between move_pages() and freeing hugepages, where
move_pages() calls follow_page(FOLL_GET) for hugepages internally and
tries to get its refcount without preventing concurrent freeing.  This
race crashes the kernel, so this patch fixes it by moving FOLL_GET code
for hugepages into follow_huge_pmd() with taking the page table lock.

This patch intentionally removes page==NULL check after pte_page.
This is justified because pte_page() never returns NULL for any
architectures or configurations.

This patch changes the behavior of follow_huge_pmd() for tail pages and
then tail pages can be pinned/returned.  So the caller must be changed to
properly handle the returned tail pages.

We could have a choice to add the similar locking to
follow_huge_(addr|pud) for consistency, but it's not necessary because
currently these functions don't support FOLL_GET flag, so let's leave it
for future development.

Here is the reproducer:

  $ cat movepages.c
  #include <stdio.h>
  #include <stdlib.h>
  #include <numaif.h>

  #define ADDR_INPUT      0x700000000000UL
  #define HPS             0x200000
  #define PS              0x1000

  int main(int argc, char *argv[]) {
          int i;
          int nr_hp = strtol(argv[1], NULL, 0);
          int nr_p  = nr_hp * HPS / PS;
          int ret;
          void **addrs;
          int *status;
          int *nodes;
          pid_t pid;

          pid = strtol(argv[2], NULL, 0);
          addrs  = malloc(sizeof(char *) * nr_p + 1);
          status = malloc(sizeof(char *) * nr_p + 1);
          nodes  = malloc(sizeof(char *) * nr_p + 1);

          while (1) {
                  for (i = 0; i < nr_p; i++) {
                          addrs[i] = (void *)ADDR_INPUT + i * PS;
                          nodes[i] = 1;
                          status[i] = 0;
                  }
                  ret = numa_move_pages(pid, nr_p, addrs, nodes, status,
                                        MPOL_MF_MOVE_ALL);
                  if (ret == -1)
                          err("move_pages");

                  for (i = 0; i < nr_p; i++) {
                          addrs[i] = (void *)ADDR_INPUT + i * PS;
                          nodes[i] = 0;
                          status[i] = 0;
                  }
                  ret = numa_move_pages(pid, nr_p, addrs, nodes, status,
                                        MPOL_MF_MOVE_ALL);
                  if (ret == -1)
                          err("move_pages");
          }
          return 0;
  }

  $ cat hugepage.c
  #include <stdio.h>
  #include <sys/mman.h>
  #include <string.h>

  #define ADDR_INPUT      0x700000000000UL
  #define HPS             0x200000

  int main(int argc, char *argv[]) {
          int nr_hp = strtol(argv[1], NULL, 0);
          char *p;

          while (1) {
                  p = mmap((void *)ADDR_INPUT, nr_hp * HPS, PROT_READ | PROT_WRITE,
                           MAP_PRIVATE | MAP_ANONYMOUS | MAP_HUGETLB, -1, 0);
                  if (p != (void *)ADDR_INPUT) {
                          perror("mmap");
                          break;
                  }
                  memset(p, 0, nr_hp * HPS);
                  munmap(p, nr_hp * HPS);
          }
  }

  $ sysctl vm.nr_hugepages=40
  $ ./hugepage 10 &
  $ ./movepages 10 $(pgrep -f hugepage)


[n-horiguchi@ah.jp.nec.com: resolve conflict to apply to v3.19.1]
Fixes: e632a938 ("mm: migrate: add hugepage migration code to move_pages()")
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Reported-by: Hugh Dickins <hughd@google.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Rik van Riel <riel@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Luiz Capitulino <lcapitulino@redhat.com>
Cc: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Cc: Lee Schermerhorn <lee.schermerhorn@hp.com>
Cc: Steve Capper <steve.capper@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 61f77eda upstream.

Currently we have many duplicates in definitions around
follow_huge_addr(), follow_huge_pmd(), and follow_huge_pud(), so this
patch tries to remove the m.  The basic idea is to put the default
implementation for these functions in mm/hugetlb.c as weak symbols
(regardless of CONFIG_ARCH_WANT_GENERAL_HUGETL B), and to implement
arch-specific code only when the arch needs it.

For follow_huge_addr(), only powerpc and ia64 have their own
implementation, and in all other architectures this function just returns
ERR_PTR(-EINVAL).  So this patch sets returning ERR_PTR(-EINVAL) as
default.

As for follow_huge_(pmd|pud)(), if (pmd|pud)_huge() is implemented to
always return 0 in your architecture (like in ia64 or sparc,) it's never
called (the callsite is optimized away) no matter how implemented it is.
So in such architectures, we don't need arch-specific implementation.

In some architecture (like mips, s390 and tile,) their current
arch-specific follow_huge_(pmd|pud)() are effectively identical with the
common code, so this patch lets these architecture use the common code.

One exception is metag, where pmd_huge() could return non-zero but it
expects follow_huge_pmd() to always return NULL.  This means that we need
arch-specific implementation which returns NULL.  This behavior looks
strange to me (because non-zero pmd_huge() implies that the architecture
supports PMD-based hugepage, so follow_huge_pmd() can/should return some
relevant value,) but that's beyond this cleanup patch, so let's keep it.

Justification of non-trivial changes:
- in s390, follow_huge_pmd() checks !MACHINE_HAS_HPAGE at first, and this
  patch removes the check. This is OK because we can assume MACHINE_HAS_HPAGE
  is true when follow_huge_pmd() can be called (note that pmd_huge() has
  the same check and always returns 0 for !MACHINE_HAS_HPAGE.)
- in s390 and mips, we use HPAGE_MASK instead of PMD_MASK as done in common
  code. This patch forces these archs use PMD_MASK, but it's OK because
  they are identical in both archs.
  In s390, both of HPAGE_SHIFT and PMD_SHIFT are 20.
  In mips, HPAGE_SHIFT is defined as (PAGE_SHIFT + PAGE_SHIFT - 3) and
  PMD_SHIFT is define as (PAGE_SHIFT + PAGE_SHIFT + PTE_ORDER - 3), but
  PTE_ORDER is always 0, so these are identical.

[n-horiguchi@ah.jp.nec.com: resolve conflict to apply to v3.19.1]
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Rik van Riel <riel@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Luiz Capitulino <lcapitulino@redhat.com>
Cc: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Cc: Lee Schermerhorn <lee.schermerhorn@hp.com>
Cc: Steve Capper <steve.capper@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit abe46b89 upstream.

Reading of analog input channels by the `INSN_READ` comedi instruction
is broken for all except channel 0.  `pci171x_ai_insn_read()` calls
`pci171x_ai_read_sample()` with the wrong value for the third parameter.
It is supposed to be the current index in a channel list (which is
always of length 1 in this case, so the index should be 0), but instead
it is passing the actual channel number.  `pci171x_ai_read_sample()`
checks the channel number encoded in the raw sample value read from the
hardware matches the channel number stored in the specified index of the
previously set up channel list and returns `-ENODATA` if it doesn't
match.  Since the index should always be 0 in this case, the match will
fail unless the channel number is also 0.  Fix it by passing 0 as the
channel index.

Note that when the bug first appeared, it was `pci171x_ai_dropout()`
that was called with the wrong parameter value.  `pci171x_ai_dropout()`
got replaced with `pci171x_ai_read_sample()` in commit 7fd2dae2
("staging: comedi: adv_pci1710: introduce pci171x_ai_read_sample()").

Fixes: 16c7eb60 ("staging: comedi: adv_pci1710: always enable PCI171x_PARANOIDCHECK code")
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 0790ec17 upstream.

If EPT was enabled, unrestricted_guest was allowed in L1 regardless of
L0.  L1 triple faulted when running L2 guest that required emulation.

Another side effect was 'WARN_ON_ONCE(vmx->nested.nested_run_pending)'
in L0's dmesg:
  WARNING: CPU: 0 PID: 0 at arch/x86/kvm/vmx.c:9190 nested_vmx_vmexit+0x96e/0xb00 [kvm_intel] ()

Prevent this scenario by masking SECONDARY_EXEC_UNRESTRICTED_GUEST when
the host doesn't have it enabled.

Fixes: 78051e3b ("KVM: nVMX: Disable unrestricted mode if ept=0")
Cc: stable@vger.kernel.org
Tested-By: Kashyap Chamarthy <kchamart@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit d0af71a3 ]

tg3_init_one() calls tg3_halt() without tp->lock despite its assumption
and causes deadlock.
If lockdep is enabled, a warning like this shows up before the stall:

  [ BUG: bad unlock balance detected! ]
  3.19.0test #3 Tainted: G            E
  -------------------------------------
  insmod/369 is trying to release lock (&(&tp->lock)->rlock) at:
  [<ffffffffa02d5a1d>] tg3_chip_reset+0x14d/0x780 [tg3]
  but there are no more locks to release!

tg3_init_one() doesn't call tg3_halt() under normal situation but
during kexec kdump I hit this problem.

Fixes: 932f19de ("tg3: Release tp->lock before invoking synchronize_irq()")
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 7a1e890e ]

cdc_ncm disagrees with usbnet about how much framing overhead should
be counted in the tx_bytes statistics, and tries 'fix' this by
decrementing tx_bytes on the transmit path.  But statistics must never
be decremented except due to roll-over; this will thoroughly confuse
user-space.  Also, tx_bytes is only incremented by usbnet in the
completion path.

Fix this by requiring drivers that set FLAG_MULTI_FRAME to set a
tx_bytes delta along with the tx_packets count.

Fixes: beeecd42 ("net: cdc_ncm/cdc_mbim: adding NCM protocol statistics")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 1e9e39f4 ]

Currently the usbnet core does not update the tx_packets statistic for
drivers with FLAG_MULTI_PACKET and there is no hook in the TX
completion path where they could do this.

cdc_ncm and dependent drivers are bumping tx_packets stat on the
transmit path while asix and sr9800 aren't updating it at all.

Add a packet count in struct skb_data so these drivers can fill it
in, initialise it to 1 for other drivers, and add the packet count
to the tx_packets statistic on completion.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Tested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit b736a623 ]

handle_offloads() calls skb_reset_inner_headers() to store
the layer pointers to the encapsulated packet. However, we
currently push the vlag tag (if there is one) onto the packet
afterwards. This changes the MAC header for the encapsulated
packet but it is not reflected in skb->inner_mac_header, which
breaks GSO and drivers which attempt to use this for encapsulation
offloads.

Fixes: 1eaa8178 ("vxlan: Add tx-vlan offload support.")
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 213dd74a ]

On Wed, Apr 15, 2015 at 05:41:26PM +0200, Nicolas Dichtel wrote:
> Le 15/04/2015 15:57, Herbert Xu a écrit :
> >On Wed, Apr 15, 2015 at 06:22:29PM +0800, Herbert Xu wrote:
> [snip]
> >Subject: skbuff: Do not scrub skb mark within the same name space
> >
> >The commit ea23192e ("tunnels:
> Maybe add a Fixes tag?
> Fixes: ea23192e ("tunnels: harmonize cleanup done on skb on rx path")
>
> >harmonize cleanup done on skb on rx path") broke anyone trying to
> >use netfilter marking across IPv4 tunnels.  While most of the
> >fields that are cleared by skb_scrub_packet don't matter, the
> >netfilter mark must be preserved.
> >
> >This patch rearranges skb_scurb_packet to preserve the mark field.
> nit: s/scurb/scrub
>
> Else it's fine for me.

Sure.

PS I used the wrong email for James the first time around.  So
let me repeat the question here.  Should secmark be preserved
or cleared across tunnels within the same name space? In fact,
do our security models even support name spaces?

---8<---
The commit ea23192e ("tunnels:
harmonize cleanup done on skb on rx path") broke anyone trying to
use netfilter marking across IPv4 tunnels.  While most of the
fields that are cleared by skb_scrub_packet don't matter, the
netfilter mark must be preserved.

This patch rearranges skb_scrub_packet to preserve the mark field.

Fixes: ea23192e ("tunnels: harmonize cleanup done on skb on rx path")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 4c0ee414 ]

This patch reverts commit b8fb4e06
because the secmark must be preserved even when a packet crosses
namespace boundaries.  The reason is that security labels apply to
the system as a whole and is not per-namespace.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit c3de6317 ]

Due to missing bounds check the DAG pass of the BPF verifier can corrupt
the memory which can cause random crashes during program loading:

[8.449451] BUG: unable to handle kernel paging request at ffffffffffffffff
[8.451293] IP: [<ffffffff811de33d>] kmem_cache_alloc_trace+0x8d/0x2f0
[8.452329] Oops: 0000 [#1] SMP
[8.452329] Call Trace:
[8.452329]  [<ffffffff8116cc82>] bpf_check+0x852/0x2000
[8.452329]  [<ffffffff8116b7e4>] bpf_prog_load+0x1e4/0x310
[8.452329]  [<ffffffff811b190f>] ? might_fault+0x5f/0xb0
[8.452329]  [<ffffffff8116c206>] SyS_bpf+0x806/0xa30

Fixes: f1bca824 ("bpf: add search pruning optimization to verifier")
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 074975d0 ]

Commit 9a2620c8 ("bnx2x: prevent WARN during driver unload")
switched the napi/busy_lock locking mechanism from spin_lock() into
spin_lock_bh(), breaking inter-operability with netconsole, as netpoll
disables interrupts prior to calling our napi mechanism.

This switches the driver into using atomic assignments instead of the
spinlock mechanisms previously employed.

Based on initial patch from Yuval Mintz & Ariel Elior

I basically added softirq starvation avoidance, and mixture
of atomic operations, plain writes and barriers.

Note this slightly reduces the overhead for this driver when no
busy_poll sockets are in use.

Fixes: 9a2620c8 ("bnx2x: prevent WARN during driver unload")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit b50edd78 ]

I noticed tcpdump was giving funky timestamps for locally
generated SYNACK messages on loopback interface.

11:42:46.938990 IP 127.0.0.1.48245 > 127.0.0.2.23850: S
945476042:945476042(0) win 43690 <mss 65495,nop,nop,sackOK,nop,wscale 7>

20:28:58.502209 IP 127.0.0.2.23850 > 127.0.0.1.48245: S
3160535375:3160535375(0) ack 945476043 win 43690 <mss
65495,nop,nop,sackOK,nop,wscale 7>

This is because we need to clear skb->tstamp before
entering lower stack, otherwise net_timestamp_check()
does not set skb->tstamp.

Fixes: 7faee5c0 ("tcp: remove TCP_SKB_CB(skb)->when")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit fde913e2 ]

Commit 1daa4303 ("net/mlx4_core: Deprecate error message at
ConnectX-2 cards startup to debug") did the deprecation only for port 1
of the card. Need to deprecate for port 2 as well.

Fixes: 1daa4303 ("net/mlx4_core: Deprecate error message at ConnectX-2 cards startup to debug")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit f60e5990 ]

We should not consult skb->sk for output decisions in xmit recursion
levels > 0 in the stack. Otherwise local socket settings could influence
the result of e.g. tunnel encapsulation process.

ipv6 does not conform with this in three places:

1) ip6_fragment: we do consult ipv6_npinfo for frag_size

2) sk_mc_loop in ipv6 uses skb->sk and checks if we should
   loop the packet back to the local socket

3) ip6_skb_dst_mtu could query the settings from the user socket and
   force a wrong MTU

Furthermore:
In sk_mc_loop we could potentially land in WARN_ON(1) if we use a
PF_PACKET socket ontop of an IPv6-backed vxlan device.

Reuse xmit_recursion as we are currently only interested in protecting
tunnel devices.

Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 666b8051 ]

On processing cumulative ACKs, the FRTO code was not checking the
SACKed bit, meaning that there could be a spurious FRTO undo on a
cumulative ACK of a previously SACKed skb.

The FRTO code should only consider a cumulative ACK to indicate that
an original/unretransmitted skb is newly ACKed if the skb was not yet
SACKed.

The effect of the spurious FRTO undo would typically be to make the
connection think that all previously-sent packets were in flight when
they really weren't, leading to a stall and an RTO.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Fixes: e33099f9 ("tcp: implement RFC5682 F-RTO")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 0c36820e ]

xen-netfront limits transmitted skbs to be at most 44 segments in size. However,
GSO permits up to 65536 bytes, which means a maximum of 45 segments of 1448
bytes each. This slight reduction in the size of packets means a slight loss in
efficiency.

Since c/s 9ecd1a75, xen-netfront sets gso_max_size to
    XEN_NETIF_MAX_TX_SIZE - MAX_TCP_HEADER,
where XEN_NETIF_MAX_TX_SIZE is 65535 bytes.

The calculation used by tcp_tso_autosize (and also tcp_xmit_size_goal since c/s
6c09fa09) in determining when to split an skb into two is
    sk->sk_gso_max_size - 1 - MAX_TCP_HEADER.

So the maximum permitted size of an skb is calculated to be
    (XEN_NETIF_MAX_TX_SIZE - MAX_TCP_HEADER) - 1 - MAX_TCP_HEADER.

Intuitively, this looks like the wrong formula -- we don't need two TCP headers.
Instead, there is no need to deviate from the default gso_max_size of 65536 as
this already accommodates the size of the header.

Currently, the largest skb transmitted by netfront is 63712 bytes (44 segments
of 1448 bytes each), as observed via tcpdump. This patch makes netfront send
skbs of up to 65160 bytes (45 segments of 1448 bytes each).

Similarly, the maximum allowable mtu does not need to subtract MAX_TCP_HEADER as
it relates to the size of the whole packet, including the header.

Fixes: 9ecd1a75 ("xen-netfront: reduce gso_max_size to account for max TCP header")
Signed-off-by: Jonathan Davies <jonathan.davies@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit fa2d8ff4 ]

Return module reference before invoking the respective vport
->destroy() function. This is needed as ovs_vport_del() is not
invoked inside an RCU read side critical section so the kfree
can occur immediately before returning to ovs_vport_del().

Returning the module reference before ->destroy() is safe because
the module unregistration is blocked on ovs_lock which we hold
while destroying the datapath.

Fixes: 62b9c8d0 ("ovs: Turn vports with dependencies into separate modules")
Reported-by: Pravin Shelar <pshelar@nicira.com>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit f5e2dc5d ]

Before commit 3900f290 ("bonding: slight
optimizztion for bond_slave_override()") the override logic was to send packets
with non-zero queue_id through the slave with corresponding queue_id, under two
conditions only - if the slave can transmit and it's up.

The above mentioned commit changed this logic by introducing an additional
condition - whether the bond is active (indirectly, using the slave_can_tx and
later - bond_is_active_slave), that prevents the user from implementing more
complex policies according to the Documentation/networking/bonding.txt.
Signed-off-by: Anton Nayshtut <anton@swortex.com>
Signed-off-by: Alexey Bogoslavsky <alexey@swortex.com>
Signed-off-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 4ad19de8 ]

tcp_v6_fill_cb() will be called twice if socket's state changes from
TCP_TIME_WAIT to TCP_LISTEN. That can result in control buffer data
corruption because in the second tcp_v6_fill_cb() call it's not copying
IP6CB(skb) anymore, but 'seq', 'end_seq', etc., so we can get weird and
unpredictable results. Performance loss of up to 1200% has been observed
in LTP/vxlan03 test.

This can be fixed by copying inet6_skb_parm to the beginning of 'cb'
only if xfrm6_policy_check() and tcp_v6_fill_cb() are going to be
called again.

Fixes: 2dc49d16 ("tcp6: don't move IP6CB before xfrm6_policy_check()")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 957f094f ]

Instead of -1 with EAGAIN, read on a O_NONBLOCK tun fd will return 0.  This
fixes this by properly returning the error code from __skb_recv_datagram.
Signed-off-by: Alex Gartrell <agartrell@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 6fd99094 ]

A local route may have a lower hop_limit set than global routes do.

RFC 3756, Section 4.2.7, "Parameter Spoofing"

>   1.  The attacker includes a Current Hop Limit of one or another small
>       number which the attacker knows will cause legitimate packets to
>       be dropped before they reach their destination.

>   As an example, one possible approach to mitigate this threat is to
>   ignore very small hop limits.  The nodes could implement a
>   configurable minimum hop limit, and ignore attempts to set it below
>   said limit.
Signed-off-by: D.S. Ljungmark <ljungmark@modio.se>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit e5eda89d ]

Netdevice registration should be performed a the end of the driver
initialization flow. If we don't do that, after calling register_netdevice,
device callbacks may be issued by higher layers of the stack before
final configuration of the device is done.

For example (VXLAN configuration race), mlx4_SET_PORT_VXLAN was issued
after the register_netdev command. System network scripts may configure
the interface (UP) right after the registration, which also attach
unicast VXLAN steering rule, before mlx4_SET_PORT_VXLAN was called,
causing the firmware to fail the rule attachment.

Fixes: 837052d0 ("net/mlx4_en: Add netdev support for TCP/IP offloads of vxlan tunneling")
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit a6e95cc7 ]

Master change notifications may occur other than when joining or
leaving a bridge, for example when being added to or removed from
a bond or Open vSwitch.

Previously in those cases rocker_port_bridge_leave() was called
which results in a null-pointer dereference as rocker_port->bridge_dev
is NULL because there is no bridge device.

This patch makes provision for doing nothing in such cases.

Fixes: 6c707945 ("rocker: implement L2 bridge offloading")
Acked-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit d0c294c5 ]

On s390x, gcc 4.8 compiles this part of tcp_v6_early_demux()

        struct dst_entry *dst = sk->sk_rx_dst;

        if (dst)
                dst = dst_check(dst, inet6_sk(sk)->rx_dst_cookie);

to code reading sk->sk_rx_dst twice, once for the test and once for
the argument of ip6_dst_check() (dst_check() is inline). This allows
ip6_dst_check() to be called with null first argument, causing a crash.

Protect sk->sk_rx_dst access by READ_ONCE() both in IPv4 and IPv6
TCP early demux code.

Fixes: 41063e9d ("ipv4: Early TCP socket demux.")
Fixes: c7109986 ("ipv6: Early TCP socket demux")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 74496134 upstream.

KVM guest can fail to startup with following trace on host:

qemu-system-x86: page allocation failure: order:4, mode:0x40d0
Call Trace:
  dump_stack+0x47/0x67
  warn_alloc_failed+0xee/0x150
  __alloc_pages_direct_compact+0x14a/0x150
  __alloc_pages_nodemask+0x776/0xb80
  alloc_kmem_pages+0x3a/0x110
  kmalloc_order+0x13/0x50
  kmemdup+0x1b/0x40
  __kvm_set_memory_region+0x24a/0x9f0 [kvm]
  kvm_set_ioapic+0x130/0x130 [kvm]
  kvm_set_memory_region+0x21/0x40 [kvm]
  kvm_vm_ioctl+0x43f/0x750 [kvm]

Failure happens when attempting to allocate pages for
'struct kvm_memslots', however it doesn't have to be
present in physically contiguous (kmalloc-ed) address
space, change allocation to kvm_kvzalloc() so that
it will be vmalloc-ed when its size is more then a page.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f9b61ff6 upstream.

It is platform/output depenedent when exactly the pipe will start
running. Sometimes we just need the (cpu) pipe enabled, in other cases
the pch transcoder is enough and in yet other cases the (DP) port is
sending the frame start signal.

In a perfect world we'd put the drm_crtc_vblank_on call exactly where
the pipe starts running, but due to cloning and similar things this
will get messy. And the current approach of picking the most
conservative place for all combinations also doesn't work since that
results in legit vblank waits (in encoder->enable hooks, e.g. the 2
vblank waits for sdvo) failing.

Completely going back to the old world before

commit 51e31d49
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Mon Sep 15 12:36:02 2014 +0200

    drm/i915: Use generic vblank wait

isn't great either since screaming when the vblank wait work because
the pipe is off is kinda nice.

Pick a compromise and move the drm_crtc_vblank_on right before the
encoder->enable call. This is a lie on some outputs/platforms, but
after the ->enable callback the pipe is guaranteed to run everywhere.
So not that bad really. Suggested by Ville.

v2: Same treatment for drm_crtc_vblank_off and encoder->disable: I've
missed the ibx pipe B select w/a, which also has a vblank wait in the
disable function (while the pipe is obviously still running).

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 5885ebda upstream.

A new fsync vs power fail test in xfstests indicated that XFS can
have unreliable data consistency when doing extending truncates that
require block zeroing. The blocks beyond EOF get zeroed in memory,
but we never force those changes to disk before we run the
transaction that extends the file size and exposes those blocks to
userspace. This can result in the blocks not being correctly zeroed
after a crash.

Because in-memory behaviour is correct, tools like fsx don't pick up
any coherency problems - it's not until the filesystem is shutdown
or the system crashes after writing the truncate transaction to the
journal but before the zeroed data in the page cache is flushed that
the issue is exposed.

Fix this by also flushing the dirty data in memory region between
the old size and new size when we've found blocks that need zeroing
in the truncate process.
Reported-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 6f30b7e3 upstream.

Commit 4f579ae7 (ext4: fix punch hole on files with indirect
mapping) rewrote FALLOC_FL_PUNCH_HOLE for ext4 files with indirect
mapping. However, there are bugs in several corner cases. This fixes 5
distinct bugs:

1. When there is at least one entire level of indirection between the
start and end of the punch range and the end of the punch range is the
first block of its level, we can't return early; we have to free the
intervening levels.

2. When the end is at a higher level of indirection than the start and
ext4_find_shared returns a top branch for the end, we still need to free
the rest of the shared branch it returns; we can't decrement partial2.

3. When a punch happens within one level of indirection, we need to
converge on an indirect block that contains the start and end. However,
because the branches returned from ext4_find_shared do not necessarily
start at the same level (e.g., the partial2 chain will be shallower if
the last block occurs at the beginning of an indirect group), the walk
of the two chains can end up "missing" each other and freeing a bunch of
extra blocks in the process. This mismatch can be handled by first
making sure that the chains are at the same level, then walking them
together until they converge.

4. When the punch happens within one level of indirection and
ext4_find_shared returns a top branch for the start, we must free it,
but only if the end does not occur within that branch.

5. When the punch happens within one level of indirection and
ext4_find_shared returns a top branch for the end, then we shouldn't
free the block referenced by the end of the returned chain (this mirrors
the different levels case).
Signed-off-by: Omar Sandoval <osandov@osandov.com>
Cc: Chris J Arges <chris.j.arges@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit a127d2bc upstream.

The hrtimer mode of broadcast queues hrtimers in the idle entry
path so as to wakeup cpus in deep idle states. The associated
call graph is :

	cpuidle_idle_call()
	|____ clockevents_notify(CLOCK_EVT_NOTIFY_BROADCAST_ENTER, ....))
	     |_____tick_broadcast_set_event()
		   |____clockevents_program_event()
			|____bc_set_next()

The hrtimer_{start/cancel} functions call into tracing which uses RCU.
But it is not legal to call into RCU in cpuidle because it is one of the
quiescent states. Hence protect this region with RCU_NONIDLE which informs
RCU that the cpu is momentarily non-idle.

As an aside it is helpful to point out that the clock event device that is
programmed here is not a per-cpu clock device; it is a
pseudo clock device, used by the broadcast framework alone.
The per-cpu clock device programming never goes through bc_set_next().
Signed-off-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: linuxppc-dev@ozlabs.org
Cc: mpe@ellerman.id.au
Cc: tglx@linutronix.de
Link: http://lkml.kernel.org/r/20150318104705.17763.56668.stgit@preeti.in.ibm.comSigned-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 61a3855b upstream.

For RoCE ports, we set the u32 PMA values based on u64 HCA counters. In case of
overflow, according to the IB spec, we have to saturate a counter to its
max value, do that.

Fixes: c3779134 ('IB/mlx4: Support PMA counters for IBoE')
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit da321133 upstream.

The rate provided at the output of a clk-divider is calculated as:

	DIV_ROUND_UP(parent_rate, div)

since commit b11d282d (clk: divider: fix rate calculation for
fractional rates). So to yield a rate not bigger than r parent_rate
must be <= r * div.

The effect of choosing a parent rate that is too big as was done before
this patch results in wrongly ruling out good dividers.

Note that this is not a complete fix as __clk_round_rate might return a
value >= its 2nd parameter. Also for dividers with
CLK_DIVIDER_ROUND_CLOSEST set the calculation is not accurate. But this
fixes the test case by Sascha Hauer that uses a chain of three dividers
under a fixed clock.

Fixes: b11d282d (clk: divider: fix rate calculation for fractional rates)
Suggested-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 26bac95a upstream.

It's an invalid approach to assume that among two divider values
the one nearer the exact divider is the better one.

Assume a parent rate of 1000 Hz, a divider with CLK_DIVIDER_POWER_OF_TWO
and a target rate of 89 Hz. The exact divider is ~ 11.236 so 8 and 16
are the candidates to choose from yielding rates 125 Hz and 62.5 Hz
respectivly. While 8 is nearer to 11.236 than 16 is, the latter is still
the better divider as 62.5 is nearer to 89 than 125 is.

Fixes: 774b5143 (clk: divider: Add round to closest divider)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 0e661006 upstream.

Stopping the vb2 thread (as used by several DVB devices) can result
in an 'UNBALANCED' warning such as this:

vb2: counters for queue ffff880407ee9828: UNBALANCED!
vb2:     setup: 1 start_streaming: 1 stop_streaming: 1
vb2:     wait_prepare: 249333 wait_finish: 249334

This is due to a race condition between stopping the thread and
calling vb2_internal_streamoff(). While I have not been able to deduce
the exact mechanism how this race condition can produce this warning,
I can see that the way the stream is stopped is likely to lead to a
race somewhere.

This patch simplifies how this is done by first ensuring that the
thread is completely stopped before cleaning up the vb2 queue. It
does that by setting threadio->stop to true, followed by a call to
vb2_queue_error() which will wake up the thread. The thread sees that
'stop' is true and it will exit.

The call to kthread_stop() waits until the thread has exited, and only
then is the queue cleaned up by calling __vb2_cleanup_fileio().

This is a much cleaner sequence and the warning has now disappeared.
Reported-by: Jurgen Kramer <gtmkramer@xs4all.nl>
Tested-by: Jurgen Kramer <gtmkramer@xs4all.nl>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 4879785e upstream.

The last argument of vb2_dc_get_user_pages() is of type enum
dma_data_direction, but the caller, vb2_dc_get_userptr() passes a value
which is the result of comparison dma_dir == DMA_FROM_DEVICE. This results
in the write parameter to get_user_pages() being zero in all cases, i.e.
that the caller has no intent to write there.

This was broken by patch "vb2: replace 'write' by 'dma_dir'".
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>