- 17 Jun, 2014 8 commits
-
-
Ben Skeggs authored
I don't know of anything this fixes, but it seems wrong anyway. Signed-off-by:Ben Skeggs <bskeggs@redhat.com>
-
Mario Kleiner authored
Need to drm_vblank_get/put() the crtc involved in a pending pageflip, or we might not get vblank irqs and updates of vblank counts and timestamps for pageflip events and flip completion. Signed-off-by:
Mario Kleiner <mario.kleiner.de@gmail.com> Signed-off-by:
-
Ben Skeggs authored
Signed-off-by: -
Pierre Moreau authored
The blob does not seem to write at that place for my NVAC, though it does for my NV96, agreeing with what is done in the if/else structure below. I guess someone forgot to remove the line when the if/else was put in place. Signed-off-by:
Pierre Moreau <pierre.morrow@free.fr> Signed-off-by:
-
Pierre Moreau authored
The specified stride was not correct, resulting in erases overlapping and part of the zcull regions being not erased at all. Signed-off-by:
-
Ben Skeggs authored
Signed-off-by: -
Ben Skeggs authored
Fixes (at least) PTHERM accesses timing out at higher clock speeds. Values and registers taken from what the binary driver does. Signed-off-by: -
Ben Skeggs authored
Signed-off-by:
-
- 11 Jun, 2014 32 commits
-
-
Dave Airlie authored
Merge branch 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6 into drm-next display rework fixes lots of displayport issues. * 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6: (43 commits) drm/nouveau/disp/dp: fix tmds passthrough on dp connector drm/nouveau/dp: probe dpcd to determine connectedness drm/nv50-: trigger update after all connectors disabled drm/nv50-: prepare for attaching a SOR to multiple heads drm/gf119-/disp: fix debug output on update failure drm/nouveau/disp/dp: make use of postcursor when its available drm/g94-/disp/dp: take max pullup value across all lanes drm/nouveau/bios/dp: parse lane postcursor data drm/nouveau/dp: fix support for dpms drm/nouveau: register a drm_dp_aux channel for each dp connector drm/g94-/disp: add method to power-off dp lanes drm/nouveau/disp/dp: maintain link in response to hpd signal drm/g94-/disp: bash and wait for something after changing lane power regs drm/nouveau/disp/dp: split link config/power into two steps drm/nv50/disp: train PIOR-attached DP from second supervisor drm/nouveau/disp/dp: make use of existing output data for link training drm/gf119/disp: start removing direct vbios parsing from supervisor drm/nv50/disp: start removing direct vbios parsing from supervisor drm/nouveau/disp/dp: maintain receiver caps in response to hpd signal drm/nouveau/disp/dp: create subclass for dp outputs ...
-
Ben Skeggs authored
Signed-off-by: -
Ben Skeggs authored
Signed-off-by: -
Ben Skeggs authored
We were sending the necessary state changes to unset the mode, but never actually hit the big GO button unless another modeset happens afterwards. Signed-off-by: -
Ben Skeggs authored
Signed-off-by: -
Ben Skeggs authored
Signed-off-by: -
Ben Skeggs authored
And at the same time, obey the spec better wrt out-of-range requests. Signed-off-by: -
Ben Skeggs authored
Signed-off-by: -
Ben Skeggs authored
Signed-off-by: -
Ben Skeggs authored
SOR_PWR has no effect to power-off DP links, unlike other SOR protocols. Instead, on the source side, we cut power to the lanes after having put the sink into D3. Link training takes care of everything required to bring it back again. Signed-off-by: -
Ben Skeggs authored
Signed-off-by: -
Ben Skeggs authored
Signed-off-by: -
Ben Skeggs authored
This previously worked for the most part due to userspace doing a modeset in response to HPD interrupts. This will allow us to properly handle cases where sync is lost for other reasons, or if userspace isn't caring. Signed-off-by: -
Ben Skeggs authored
Some kind of update? Needed to make the power-down take effect at least. Signed-off-by: -
Ben Skeggs authored
We want to be able to power down the lanes for DPMS off. Signed-off-by: -
Ben Skeggs authored
Same place as for SOR, between detach and attach phases. Signed-off-by: -
Ben Skeggs authored
Signed-off-by: -
Ben Skeggs authored
Signed-off-by: -
Ben Skeggs authored
Signed-off-by: -
Ben Skeggs authored
Signed-off-by: -
Ben Skeggs authored
Signed-off-by: -
Ben Skeggs authored
Signed-off-by: -
Ben Skeggs authored
This will, at some point, be used to replace various bits and pieces of code doing direct bios parsing. For now, it'll just be used for some DP improvements. Signed-off-by: -
Ben Skeggs authored
Signed-off-by: -
Ben Skeggs authored
Signed-off-by: -
Ben Skeggs authored
Signed-off-by: -
Ben Skeggs authored
There's also provisions to allow a pad to be locked with a specific routing, for an indefinite period of time. This will be used in future patches. The G94+ pad driver will now also power-down pads when not required. Signed-off-by: -
Ben Skeggs authored
This was a half-finished hack before, just enough to handle the shared aux/i2c pad thing on G94 and up. We got lucky with locking etc up until now, as this was (generally) all protected by the DRM mode_config lock. It's about to become a lot more likely to hit the races. Signed-off-by: -
Ben Skeggs authored
Signed-off-by: -
Ben Skeggs authored
Signed-off-by: -
Ben Skeggs authored
Signed-off-by: -
Ben Skeggs authored
Signed-off-by:
-
