- 23 Feb, 2018 14 commits
-
-
James Smart authored
Updated Copyright in files updated as part of 12.0.0.0 Signed-off-by:
Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by:
James Smart <james.smart@broadcom.com> Reviewed-by:
Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com>
-
James Smart authored
Update the driver version to 12.0.0.0 Signed-off-by:
-
James Smart authored
The hardware offload for NVME commands was created when the FC-NVME standard was setting SGL Descriptor Type to SGL Data Block Descriptor (0h) and SGL Descriptor Sub Type to Address (0h). A late change in NVMe-over-Fabrics obsoleted these values, creating a transport SGL descriptor type with new values to go into these fields. For initial hardware support, in order to be compliant to the spec, use host-supplied cmd IU buffers instead of the adapter generated values. Later hardware will correct this. Add a module parameter to override this offload disablement if looking for lowest latency. This is reasonable as nothing in FC-NVME uses the SQE SGL values. Signed-off-by:
-
James Smart authored
Newer hardware more strictly enforces buffer lenghts, causing an mis-set value to be identified. Older hardware won't catch it. The difference is benign on old hardware. Set the right embedded buffer length for nvme ios. Signed-off-by:
-
James Smart authored
The current driver isn't taking advantage of a performance hint whereby the initial data buffer descriptor can be placed in the WQE as well as the SGL. Add the logic to detect support for the feature and to use it when supported. Signed-off-by:
-
James Smart authored
Current code is very explicit in what it allows to be downloaded. The driver checking prevented G7 firmware download. The driver checking is unnecessary as the device will validate what it receives. Revise the firmware download interface checking. Added a little debug support in case there is still a failure. Signed-off-by:
-
James Smart authored
Traditional SLI4 required the driver to clear Valid bits on EQEs and CQEs after consuming them. The new if_type=6 hardware will cycle the value for what is valid on each queue itteration. The driver no longer has to touch the valid bits. This also means all the cpu cache dirtying and perhaps flush/refill's done by the hardware in accessing the EQ/CQ elements is eliminated. Signed-off-by:
-
James Smart authored
The G7 adapter supports 64G link speeds. Add support to the driver. In addition, a small cleanup to replace the odd bitmap logic with a switch case. Signed-off-by:
-
James Smart authored
Add PCI ids for the new G7 adapter Signed-off-by:
-
James Smart authored
New if_type=6 adapters support an additional BAR that provides apertures to allow direct WQE to adapter push support - termed Direct Packet Push (DPP). WQ creation differs slightly to ask for a WQ to be DPP-ized. When submitting a WQE to a DPP WQ, it is submitted to the host memory for the WQ normally, but is also written by the host cpu directly to a BAR aperture. Write buffer coalescing in hardware is (hopefully) turned on, enabling single pci write operation support. The doorbell is thing rung to indicate the WQE is available and was pushed to the aperture. This patch: - Updates the WQ Create commands for the DPP options - Adds the bar mapping for if_type=6 DPP bar - Adds the WQE pushing to the DDP aperture received from WQ create - Adds a new module parameter to disable DPP operation if desired. Default is enabled. Signed-off-by:
-
James Smart authored
New hardware supports a SLI-4 interface, but with a new if_type variant of 6. If_type=6 has a different PCI BAR map, separate EQ/CQ doorbells, and some changes in doorbell formats. Add the changes for the if_type into headers, adapter initialization and control flows. Add new eq and cq handlers. Signed-off-by:
-
James Smart authored
Up until now, all SLI-4 devices had the same doorbells at the same bar locations. With newer hardware, there are now independent EQ and CQ doorbells and the bar locations differ. Prepare the code for new hardware by separating the eq/cq doorbell into separate components. The components can be set based on if_type. Signed-off-by:
-
James Smart authored
Up until now, an SLI-4 device had no variance in the way it handled its EQs and CQs. With newer hardware, there are now differences in doorbells and some differences in how entries are valid. Prepare the code for new hardware by creating a sli4-based callout table that can be set based on if_type. Signed-off-by:
-
Souptick Joarder authored
Use dma_pool_zalloc() instead of dma_pool_alloc + memset Signed-off-by:
Souptick Joarder <jrdr.linux@gmail.com> Acked-by:
Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by:
-
- 22 Feb, 2018 1 commit
-
-
Souptick Joarder authored
Use dma_pool_zalloc() instead of dma_pool_alloc + memset Signed-off-by:
Manish Rangankar <Manish.Rangankar@cavium.com> Signed-off-by:
-
- 15 Feb, 2018 13 commits
-
-
Stanislav Nijnikov authored
This patch introduces a sysfs group entry for the UFS attributes. The group adds "attributes" folder under the UFS driver sysfs entry (/sys/bus/platform/drivers/ufshcd/*). The attributes are shown as hexadecimal numbers. The full information about the attributes could be found at UFS specifications 2.1. Signed-off-by:
Stanislav Nijnikov <stanislav.nijnikov@wdc.com> Reviewed-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Stanislav Nijnikov authored
This patch introduces a sysfs group entry for the UFS flags. The group adds "flags" folder under the UFS driver sysfs entry (/sys/bus/platform/drivers/ufshcd/*). The flags are shown as boolean value ("true" or "false"). The full information about the UFS flags could be found at UFS specifications 2.1. Signed-off-by: -
Stanislav Nijnikov authored
This patch introduces a sysfs group entry for the UFS unit descriptor parameters. The group adds "unit_descriptor" folder under the corresponding SCSI device sysfs entry (/sys/class/scsi_device/*/device/). The parameters are shown as hexadecimal numbers. The full information about the parameters could be found at UFS specifications 2.1. Signed-off-by:
-
Stanislav Nijnikov authored
The patch introduces an additional field in the scsi_host_template structure - struct attribute_group **sdev_group. This field allows to define groups of attributes. It will provide an ability to use binary attributes as well as device attributes and to group them under subfolders if necessary. Signed-off-by:
-
Stanislav Nijnikov authored
This patch introduces a sysfs group entry for the UFS string descriptors. The group adds "string_descriptors" folder under the UFS driver sysfs entry (/sys/bus/platform/drivers/ufshcd/*). The folder will contain 5 files that will show string values defined by the UFS spec: a manufacturer name, a product name, an OEM id, a serial number and a product revision. The full information about the string descriptors could be found at UFS specifications 2.1. Signed-off-by:
-
Stanislav Nijnikov authored
This patch introduces a sysfs group entry for the UFS power descriptor parameters. The group adds "power_descriptor" folder under the UFS driver sysfs entry (/sys/bus/platform/drivers/ufshcd/*). The parameters are shown as hexadecimal numbers. The full information about the parameters could be found at UFS specifications 2.1. Signed-off-by:
-
Stanislav Nijnikov authored
This patch introduces a sysfs group entry for the UFS health descriptor parameters. The group adds "health_descriptor" folder under the UFS driver sysfs entry (/sys/bus/platform/drivers/ufshcd/*). The parameters are shown as hexadecimal numbers. The full information about the parameters could be found at UFS specifications 2.1. Signed-off-by:
-
Stanislav Nijnikov authored
This patch introduces a sysfs group entry for the UFS geometry descriptor parameters. The group adds "geometry_descriptor" folder under the UFS driver sysfs entry (/sys/bus/platform/drivers/ufshcd/*). The parameters are shown as hexadecimal numbers. The full information about the parameters could be found at UFS specifications 2.1. Signed-off-by:
-
Stanislav Nijnikov authored
This patch introduces a sysfs group entry for the UFS interconnect descriptor parameters. The group adds "interconnect_descriptor" folder under the UFS driver sysfs entry (/sys/bus/platform/drivers/ufshcd/*). The parameters are shown as hexadecimal numbers. The full information about the parameters could be found at UFS specifications 2.1. Signed-off-by:
-
Stanislav Nijnikov authored
This patch introduces a sysfs group entry for the UFS device descriptor parameters. The group adds "device_descriptor" folder under the UFS driver sysfs entry (/sys/bus/platform/drivers/ufshcd/*). The parameters are shown as hexadecimal numbers. The full information about the parameters could be found at UFS specifications 2.1. Signed-off-by:
-
Stanislav Nijnikov authored
This patch introduces attribute group to show existing sysfs entries. Signed-off-by:
-
Martin Wilck authored
Error injection in scsi_debug (e.g. opts=16, SDEBUG_OPT_TRANSPORT_ERR) currently doesn't work correctly because the test for sqcp in resp_read_dt0() and similar resp_*() functions always fails. sqcp is set from cmnd->host_scribble, which is set in schedule_resp(), which is called from scsi_debug_queuecommand() after calling the resp_* function. Defer calling resp_*() until after cmnd->host_scribble is set in schedule_resp(). Fixes: c4837394 "scsi_debug: add multiple queue support" Signed-off-by:
Martin Wilck <mwilck@suse.com> Acked-by:
Douglas Gilbert <dgilbert@interlog.com> Signed-off-by:
-
Colin Ian King authored
Don't populate the const read-only arrays spi_test_unit_ready and spi_test_unit_ready on the stack but instead make them static. Makes the object code smaller by over 100 bytes: Before: text data bss dec hex filename 40171 12832 128 53131 cf8b drivers/scsi/scsi_transport_spi.o After: text data bss dec hex filename 39922 12976 128 53026 cf22 drivers/scsi/scsi_transport_spi.o (gcc version 7.2.0 x86_64) Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
- 14 Feb, 2018 12 commits
-
-
Martin Wilck authored
If every_nth > 0, the injection flags must be reset for commands that aren't supposed to fail (i.e. that aren't "nth"). Otherwise, commands will continue to fail, like in the every_nth < 0 case. Signed-off-by:
-
Douglas Gilbert authored
The Start Stop Unit (SSU) command takes in the order of a second to complete on some SAS SSDs and longer on hard disks. Synchronize Cache (SC) can also take some time. Both commands have an IMMED bit in their cdbs for those apps that don't want to wait. This patch introduces a long delay for those commands when the IMMED bit is clear. Since SC is a media access command then when the fake_rw option is active, its cdb processing is skipped and it returns immediately. The SSU command is not altered by the setting of the fake_rw option. These actions are not changed by this patch. Changes since v1: - clear the cdb mask of SYNCHRONIZE CACHE(16) cdb in byte 1, bit 0 Changes: - add the SYNCHRONIZE CACHE(16) command - together with the existing START STOP UNIT and SYNCHRONIZE CACHE(10) commands process the IMMED bit in their cdbs - if the IMMED bit is set, return immediately - if the IMMED bit is clear, treat the delay parameter as having a unit of one second - in the SYNCHRONIZE CACHE processing do a bounds check Signed-off-by: -
John Pittman authored
Pointer styling issues exposed by checkpatch.pl in scsi_debug.c: ERROR: "foo * bar" should be "foo *bar" Fixed 37 total errors reported. [mkp: fixed typo noticed by Doug] Signed-off-by:
John Pittman <jpittman@redhat.com> Acked-by:
-
Bart Van Assche authored
Make scsi_test_unit_ready() send at most as many TURs as specified in the 'retries' argument instead of retries * (retries + 1) / 2. Signed-off-by:
Bart Van Assche <bart.vanassche@wdc.com> Reviewed-by:
Hannes Reinecke <hare@suse.com> Signed-off-by:
-
Bart Van Assche authored
The eh_deadline definition occurs in the middle of the code for releasing a host. Avoid splitting the host release code by moving the definition of the eh_deadline parameter to the top of the hosts.c source file. Signed-off-by:
Bart Van Assche <bart.vanassche@sandisk.com> Reviewed-by:
-
Bart Van Assche authored
After the patch that introduced this function was posted on the linux-scsi mailing list an explanation was posted why this patch is correct. Since that explanation contains important information, add a summary of it above the code that explanation applies to. See also http://www.spinics.net/lists/linux-scsi/msg106326.html. References: e494f6a7 ("[SCSI] improved eh timeout handler") Signed-off-by:
Hannes Reinecke <hare@suse.de> Cc: Christoph Hellwig <hch@lst.de> Cc: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by:
-
Bart Van Assche authored
Use the sgl_alloc_order() and sgl_free_order() functions instead of open coding these functions. Signed-off-by:
-
Bart Van Assche authored
Signed-off-by:
-
Bart Van Assche authored
Use the sgl_alloc_order() and sgl_free_order() functions instead of open coding these functions. Signed-off-by:
Brian King <brking@linux.vnet.ibm.com> Reviewed-by:
-
Colin Ian King authored
There are several occurrances where pointer ioadl is initialized with a value that is never read and where it is re-assigned a new value later on, hence the initialization is redundant and can be removed. Cleans up clang warnings: drivers/scsi/pmcraid.c:1028:29: warning: Value stored to 'ioadl' during its initialization is never read drivers/scsi/pmcraid.c:3178:29: warning: Value stored to 'ioadl' during its initialization is never read drivers/scsi/pmcraid.c:5495:29: warning: Value stored to 'ioadl' during its initialization is never read drivers/scsi/pmcraid.c:5668:29: warning: Value stored to 'ioadl' during its initialization is never read Signed-off-by:
-
Colin Ian King authored
Variable bit is initialized with a value that is never read and is being updated immediately after the initialization, hence the initialization is redundant and can be removed. Cleans up clang warning: drivers/scsi/isci/host.c:2769:8: warning: Value stored to 'bit' during its initialization is never read Signed-off-by:
-
Arnd Bergmann authored
Building with link time optimizations produces a false-positive section mismatch warning: WARNING: vmlinux.o(.data+0xf8c8): Section mismatch in reference from the variable driver_template.lto_priv.6915 to the function .init.text:sym53c416_detect() The variable driver_template.lto_priv.6915 references the function __init sym53c416_detect() If the reference is valid then annotate the variable with __init* or __refdata (see linux/init.h) or name the variable: *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console The ->detect callback is always entered from the init_this_scsi_driver() init function, but apparently LTO turns the optimized direct function call into an indirect call through a non-__initdata pointer. All drivers using init_this_scsi_driver() are for ancient hardware, and most don't mark the detect() callback as __init(), so I'm just removing the annotation here to kill off the warning instead of doing a larger rework. [mkp: typo] Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
