After downloading the firmware, firmware status is checked by
reading a register. Polling interval is 100 msecs. Therefore 100
retries means the status is checked for 10 secs which is more than
sufficient for firmware to get ready.

This patch removes 1000 retries macro usage, because 100secs
time is not practical.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Clear the data pointer stored in USB interface structure in
this handler. This helps to return from mwifiex_usb_disconnect()
if driver deinitialization is already performed while handling
an error path for mwifiex_usb_probe().

USB8797 card gets enumerated twice. First enumeration is for
firmware download and second enumeration expects firmware
initialization. mwifiex_usb_probe() always takes care of
deinitialization for first enumeration after firmware download.

Also, this change matches our handling for SDIO and PCIe
interfaces.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

As if_ops.init_if() is called in mwifiex_register(),
corresponding cleanup routine should be called in
mwifiex_unregister().

Currently it's there in mwifiex_adapter_cleanup(), hence
interface specific cleanup is not performed if driver
initialization is failed.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

It is already there in mwifiex_unregister(). So unnecessary
call in mwifiex_adapter_cleanup() is removed in this patch.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Currently it is in mwifiex_adapter_cleanup() which doesn't get
called if driver initialization is failed causing memory leak.

scan_delay_timer is initialized in mwifiex_register(), so it
should be deleted in mwifiex_unregister(). Hence it has been
moved to appropriate place.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

If reboot command is issued when device is in connected state,
system hangs while booting. This issue is fixed by doing cleanup
in shutdown handler.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch is bug fix for an invalid boundry check for WPS IE.
We should check max IE length against defined macro; instead we were
checking it against size of pointer. Fix it.
Also move IE length check before allocation of memory.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

During P2P handshake, P2P client needs to send deauth after EAPOL
FAILURE to GO. We need add bss mode for P2P client when handle deauth
request.

Without this change, deauth can not be sent out from P2P client side.
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Before sending command to firmware, we need to check the frame type.
We skip registering the mgmt frame that has already been registered.
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Some GO will send deauth or disassoc packet at the end of WPS
handshake, which causes P2P connecion failure due to the race
condition between event path and data path.
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In function 'mwifiex_write_data_complete' it need tx info to find
the mwifiex_private to updates statistics and wake up tx queues.
Or we may trigger tx queues timeout when transmitting lots of mgmt
frames.
Signed-off-by: Huawei Yang <harvey.huawei.yang@gmail.com>
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Delete packets from TX queues for this mwifiex_private structure
when bridged packet count reaches maximum threshold. Bridged packets
from each RA List are deleted till they fall to low threshold of 128.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Maintain total outstanding packet count for RA list instead of total
outstanding size as packet count metric seems more reasonable for
checking threshold etc.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

pkt_count is used to determine if BA can be formed on this RA list
by comparing it with randomly generated BA threshold. The pkt_count
variable name here is ambiguous and does not reflect its usage
correctly. Rename it to ba_pkt_count.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Under uAP mode mwifiex may stop all net tx queues on forwarding
packets. This may stop some tx queues and they never have chance
to be waked up. There is also no need to check tx_pending and
stop queues here. Because local host has such kind of check when
transmitting packets and it's not proper to have forwarding affect
local transmitting.
Signed-off-by: Huawei Yang <harvey.huawei.yang@gmail.com>
Reviewed-by: Avinash Patil <patila@marvell.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Steinar reported reallocations of skb->head with IPv6, leading to
a warning in skb_try_coalesce()

It turns out iwl3945 has several problems :

1) skb->truesize is underestimated.
   We really consume PAGE_SIZE bytes for a fragment,
   not the frame length.
2) 128 bytes of initial headroom is a bit low and forces reallocations.
3) We can avoid consuming a full page for small enough frames.
Reported-by: Steinar H. Gunderson <sesse@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paul Stewart <pstew@google.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In production code, don't use -Werror,
as it causes random compilation failures due to compiler version and options used.

With every new version of gcc, it becomes stricter and report more warnings.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The git tree is in github.com nowadays.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

I forgot to add an entry to MAINTAINERS when submitting the driver.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add support for TCP and UDP HW checksum offloading.
RX chain is allways configured for offload mode.
In case of checksum error in RX path the DMA L4 error bit(5)
will be set to 1 and driver will drop the packet.
TX checksum offloading is configrable (ethtool -K).
TX descriptors are configured for checksum offload according
to the SKB protocol type (TCP/UDP, IPV4/6), Upon mismatch drop
the TX packet (checksum required but not TCP/UDP IPV4/6 type).
Signed-off-by: Kirshenbaum Erez <erezk@wilocity.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Release fragments in the order of allocation; including one for skb head
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Note that the driver doesn't directly use this field, but it should be
correctly defined in any case.
Signed-off-by: Solomon Peachy <pizza@shaftnet.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

* CUS217 specific initvals have to be programmed.
* iniAdditional is not used for AR9462/AR9565, remove it.
* Handle channel 2484 for regulatory compliance.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Right now, even though these chips support cross-band
FCC, the code is non-functional since we bail out early if
the channelFlags differ. Fix this so that cross-band
FCC works for cards that support this feature.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fast Channel Change across 2G/5G bands is supported
only by AR9462 and AR9565. Add a HW capability field
to indicate this.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Relegate 2 phy messages to debug status as they create excessive
log spam, noted in multiple bugzillas for brcmsmac v3.8 and up.
This is a follow on to net-next 99e94940:
brcmsmac: Reduce log spam in heavy tx, make err print in debug

 brcmsmac bcma0:0: phyerr 0x10, rate 0x14
 brcmsmac bcma0:0: brcms_c_ampdu_dotxstatus_complete:
ampdu tx phy error (0x10)
Signed-off-by: John Greene <jogreene@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The return value of bcma_erom_get_addr_desc() is a unsigned value and it
could wrap around in the two complement writing. This happens for one
core in the BCM4708 SoC.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

It is better to return the actual error code than just -1.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

These are the chipIDs of some ARM based SoCs from the BCM47xx line.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

To make it possible to use the SoC host interface with ARM SoCs do not
depend on the MIPS driver any more.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

These cores were found on a BCM4708 (chipid 53010), this is a ARM SoC
with two Cortex A9 cores.

bcma: bus0: Found chip with id 0xCF12, rev 0x00 and package 0x02
bcma: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x2A, class 0x0)
bcma: bus0: Core 1 found: DMA (manuf 0x4BF, id 0x502, rev 0x01, class 0x0)
bcma: bus0: Core 2 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x04, class 0x0)
bcma: bus0: Core 3 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x04, class 0x0)
bcma: bus0: Core 4 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x04, class 0x0)
bcma: bus0: Core 5 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x04, class 0x0)
bcma: bus0: Core 6 found: PCIe Gen 2 (manuf 0x4BF, id 0x501, rev 0x01, class 0x0)
bcma: bus0: Core 7 found: PCIe Gen 2 (manuf 0x4BF, id 0x501, rev 0x01, class 0x0)
bcma: bus0: Core 8 found: ARM Cortex A9 core (ihost) (manuf 0x4BF, id 0x510, rev 0x01, class 0x0)
bcma: bus0: Core 9 found: USB 2.0 (manuf 0x4BF, id 0x504, rev 0x01, class 0x0)
bcma: bus0: Core 10 found: USB 3.0 (manuf 0x4BF, id 0x505, rev 0x01, class 0x0)
bcma: bus0: Core 11 found: SDIO3 (manuf 0x4BF, id 0x503, rev 0x01, class 0x0)
bcma: bus0: Core 12 found: ARM Cortex A9 JTAG (manuf 0x4BF, id 0x506, rev 0x01, class 0x0)
bcma: bus0: Core 13 found: Denali DDR2/DDR3 memory controller (manuf 0x4BF, id 0x507, rev 0x01, class 0x0)
bcma: bus0: Core 14 found: ROM (manuf 0x4BF, id 0x508, rev 0x01, class 0x0)
bcma: bus0: Core 15 found: NAND flash controller (manuf 0x4BF, id 0x509, rev 0x01, class 0x0)
bcma: bus0: Core 16 found: SPI flash controller (manuf 0x4BF, id 0x50A, rev 0x01, class 0x0)
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Finish all SW context modifications prior to notifying hardware

It used to be race condition: if HW finish Tx and issue Tx completion IRQ very fast,
prior to SW context update in wil_tx_vring, Tx completion will mis-handle descriptor, as
SW part will have no skb pointer stored.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Enable adding more data to the SW context.
For now, add flag "mapped_as_page", to separate decisions on free-ing skb
and type of DMA mapping.
This allows linking skb itself to any descriptor of fragmented skb.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

No need to modify HW descriptor, as it will be re-initialized on Tx.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When destroying Rx vring, branch for Rx used wrong Tx descriptor:
while SW context was taken for "head", HW descriptor was, by mistake,
taken from "tail"
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

FW guys changed header structure; align driver code
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The Linksys AE3000 device is based on the RT3573
chipset. The support for this chipset is available
already, and the AE3000 device works with the driver.

Only managed mode works correctly at the moment,
for AP mode additional changes are needed in the
driver.

Also add a new RT2800USB_RT3573 Kconfig option and
only enable support for RT3573 based devices if
that is enabled.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>