- 06 Jun, 2012 19 commits
-
-
Sujith Manoharan authored
ASPM has to be disabled when BTCOEX is in use, do this properly by calling the bus-specific ASPM init routine after the BTCOEX scheme has been determined. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Sujith Manoharan authored
Instead of cluttering ath9k_init_device() with 'ath_softc' specific initialization code, use ath9k_init_softc() to setup driver-specific work routines, timers etc. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Arik Nemtsov authored
When performing a HW restart for an AP mode interface, add stations back only after the AP is beaconing. This mimics the normal flow of STA addition on AP. Some devices (wlcore) do not support adding stations before beaconing, so this has the added benefit of making recovery work for them. Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Chris Yungmann authored
Fixed checkpatch and sparse warnings related to aiutils.* Signed-off-by: Chris Yungmann <yungmann.chris@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
The remain-on-channel time validation shouldn't depend on the value of HZ, as it does now with the check against jiffies, since then you might use a value that works on one system but not on another. Fix it by checking against a minimum that's fixed. Also add validation of the wait duration for a management frame TX since this also translates into remain-on-channel internally. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Hauke Mehrtens authored
I found this core on a BCM4322, a PCI card in the Linksys WRT610N V1. This core is not used by the driver, this patch just makes ssb show the correct name. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Pontus Fuchs authored
drv_resume can get called without a prior call to drv_suspend. Consider the following steps: 1. Suspend is started but driver's drv_suspend returns error. 2. Suspend is aborted. local->wowlan flag is left set. 3. Interface is removed. 4. Suspend again. This time open_count is 0 so drv_suspend is not called and local->wowlan not cleared. 5. On resume ieee80211_reconfig will call drv_resume since local->wowlan is set. Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Chun-Yeow Yeoh authored
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
Make mac80211 print a message when it disables HT due to the connection using WEP/TKIP or due to the AP not supporting WMM/QoS. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Stanislaw Gruszka authored
For each EDCA TX queue change default settings (in STA mode) to conform old 802.11b/g channel access rules. This is needed for drivers that do not have QoS enable/disable "switch" (like rt2x00) to make them work properly with legacy APs. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Vivek Natarajan authored
Configure CWmin based on slot time for IBSS mode. This helps in increasing the beacon distribution of ath9k to accepted levels in 11a mode. Signed-off-by: Vivek Natarajan <nataraja@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Zero.Lin authored
Signed-off-by: Zero.Lin <Zero.Lin@mediatek.com> Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Stanislaw Gruszka authored
Similar like other drivers including iwl3945, do not configure group keys to the hardware (on Ad-Hoc mode) to make IBSS RSN work. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Stanislaw Gruszka authored
Similar like other drivers, do not configure group keys to the hardware (on Ad-Hoc mode) to make IBSS RSN work. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Zefir Kurtisi authored
Updates for spectral scanning register modification for AR93x: * fix bits for spectral_scan_count * add bits for new parameters Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Alex Hung authored
__rfkill_switch_all() switches the state of devices of a given type; however, it does not switch devices of all type (RFKILL_TYPE_ALL). As a result, it ignores the keycode "KEY_RFKILL" from another module, i.e. eeepc-wmi. This fix is to make __rfkill_switch_all() to be able to switch not only devices of a given type but also all devices. Signed-off-by: Alex Hung <alex.hung@canonical.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
Now that we've removed all uses of the set_channel API except for the monitor channel and in libertas, clarify this. Split the libertas mesh use into a new libertas_set_mesh_channel() operation, just to keep backward compatibility, and rename the normal set_channel() to set_monitor_channel(). Also describe the desired set_monitor_channel() semantics more clearly. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wirelessJohn W. Linville authored
Conflicts: drivers/net/wireless/iwlwifi/iwl-drv.c
-
- 05 Jun, 2012 21 commits
-
-
Stanislav Yakovlev authored
We separate reading of device's eeprom content from writing it back to the device's sram. Signed-off-by: Stanislav Yakovlev <stas.yakovlev@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Avinash Patil authored
mwifiex uAP supports NL80211_HIDDEN_SSID_ZERO_LEN type of hidden SSID only. NL80211_HIDDEN_SSID_ZERO_CONTENTS is not supported. Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Kiran Divekar <dkiran@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Avinash Patil authored
Mark bss_config parameters as invalid before setting AP channel. This prevents from setting invalid parameters while setting AP channel to FW. Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Kiran Divekar <dkiran@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
Just like the AP mode patch, instead of setting the channel and then joining the mesh network, provide the channel to join the network on to the join_mesh() function. Like in AP mode, you can also give the channel to the join-mesh nl80211 command now. Unlike AP mode, it picks a default channel if none was given. As libertas uses mesh mode interfaces but has no join_mesh callback and we can't simply break it, keep some compatibility code for that case and configure the channel directly for it. In the non-libertas case, where we store the channel until join, allow setting it while the interface is down. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
If it worked (Felix says it doesn't right now), the typical use-case for WDS interfaces would be to be slaved to AP mode interfaces. Therefore, it isn't necessary to set the channel on WDS interfaces. As they don't support powersave or anything like that, they also couldn't use a different channel anyway. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
Instead of setting the channel first and then starting the AP, let cfg80211 store the channel and provide it as one of the AP settings. This means that now you have to set the channel before you can start an AP interface, but since hostapd/wpa_supplicant always do that we're OK with this change. Alternatively, it's now possible to give the channel as an attribute to the start-ap nl80211 command, overriding any preset channel. Cc: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
Change cfg80211_can_beacon_sec_chan() to return true if there is no secondary channel to simplify all the current users of it. They all check the channel type before calling the function because it returns false if there's no secondary channel. Also actually document the return value. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
Move the set_channel function up so it can be used by other code in this file in the future. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
There's no need for ieee80211_set_channel to check whether a change in configuration happened since ieee80211_hw_config() auto-detects it. Additionally, it's wrong to pretend the HT config for the BSS changed, it didn't, the BSS can't be up & running (AP beaconing etc.) when the channel type is changed anyway. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
Instead of passing around the entire HT information IE, extract only the HT parameters field and disable HT if the HT information IE isn't present and well- formed. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
Almost all wireless tools have transitioned to or at least added compatibility with nl80211 so there's no real need for CONFIG_CFG80211_WEXT any more. Mark it for removal, and also change the default to not be enabled. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
The only user of this was hal prior to its 0.5.12 release which happened over two years ago, so I'm sure this can be removed without issues. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Meenakshi Venkataraman authored
Add a debugging log when using shadow registers. Also fix a minor typo in this connection. Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
Mostly clean up indentation around parentheses after if, function calls, etc. and also a few unneeded line breaks and some other things. Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Reviewed-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
This code is a library to be used by multiple opmodes, so move it into the iwlwifi module. Reviewed-by: Donald H Fry <donald.h.fry@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Don Fry authored
This is the next step in splitting up the driver, making the uCode API dependent pieces of it live in separate modules. Right now there's only one so it's not user-selectable, but we're actively working on more. Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Don Fry <donald.h.fry@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
This is common, not uCode API specific, so move it to the transport together with the command header struct definition. Reviewed-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com> Reviewed-by: Guy Cohen <guy.cohen@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
This is intended to be set whenever wakeup will be needed upon suspend, not only when suspending, so use the new callbacks to set it then. Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Gregory Greenman authored
This macro is needed by other transports besides PCIe, thus moving to a common location. Signed-off-by: Gregory Greenman <gregory.greenman@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Reviewed-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Emmanuel Grumbach authored
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Reviewed-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Emmanuel Grumbach authored
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Reviewed-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-