- 12 Apr, 2013 32 commits
-
-
Philipp Zabel authored
Remove the tve_di clock from the CCM clock tree. It will be provided by the Television Encoder driver, as this clock is an output signal of the TVE module. Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
-
Philipp Zabel authored
This is needed so the Television Encoder driver can set the rate on tve_clk and have it propagated up to pll4_sw. Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
-
Philipp Zabel authored
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
-
Philipp Zabel authored
On i.MX53, there is only tve_ext_sel. Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
-
Sascha Hauer authored
This adds the clock gates and the binding documentation for PATA and SRTC. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
-
Shawn Guo authored
The i.MX6 Quad can be fused as i.MX6 Dual chip, and similarly i.MX6 DualLite can be fused as i.MX6 Solo. The actual number of available cores can be found out from SCU. Since we do not reflect the fusing thing in device tree, the function arm_dt_init_cpu_maps() will always call set_cpu_possible(true) for 4 cores on i.MX6 Quad/Dual and 2 cores for i.MX6 DualLite/Solo. This causes failures when kernel tries to bring those unavailable cores online. For example, the following failure message will be seen when booting an i.MX6 Solo chip. CPU1: failed to come online Though kernel will still boot fine, the message is somehow annoying. Let's get rid of it by calling set_cpu_possible(false) on those unavailable cores. While at it, the set_cpu_possible(true) for available cores is removed, since it's already been done in arm_dt_init_cpu_maps(). Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
-
Shawn Guo authored
The i.MX6 DualLite/Solo is another i.MX6 family SoC, which is highly compatible with i.MX6 Quad/Dual. And that's why we choose to support it using imx6q code with cpu_is_imx6dl() check when necessary. Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
-
Gwenhael Goavec-Merou authored
mxc_device_init() is mandatory for mxc_aips and mxc_ahb bus registration, needed as parents, at least, for gpio and dma. Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
-
Fabio Estevam authored
Add CONFIG_GPIO_SYSFS as it is helpful for accessing GPIO from userspace. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
-
Fabio Estevam authored
Select CONFIG_PERF_EVENTS so that oprofile can be used. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Dirk Behme <dirk.behme@gmail.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
-
Martin Fuzzey authored
These two clocks connect to external pins and can be muxed to various internal clocks. They are typically used either for debugging or to provide clocks to external chips (eg audio codecs). Currently only the selectable clocks that already exist in the clock tree have been added. Signed-off-by: Martin Fuzzey <mfuzzey@parkeon.com> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
-
Philipp Zabel authored
Request the System Reset Controller to reset the IPU if specified via device tree phandle. Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Reviewed-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Marek Vasut <marex@denx.de> Reviewed-by: Pavel Machek <pavel@ucw.cz> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
-
Philipp Zabel authored
The SRC has auto-deasserting reset bits that control reset lines to the GPU, VPU, IPU, and OpenVG IP modules. This patch adds a reset controller that can be controlled by those devices using the reset controller API. Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Reviewed-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Marek Vasut <marex@denx.de> Reviewed-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
-
Shawn Guo authored
Function imx_anatop_get_digprog() that reads register ANADIG_DIGPROG is called to identify silicon version. Users might query silicon version earlier than regmap subsystem is ready. For example, imx6q clock driver query revision in mx6q_clocks_init(), where regmap is not initialized yet. Change imx_anatop_get_digprog() to map anatop block and read ANADIG_DIGPROG in the native way, so that the function can work at very early stage. While at it, let's move imx_print_silicon_rev() back to imx6q_timer_init() to have the message show up a little earlier. Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
-
Philipp Zabel authored
On i.MX6q revision 1.1 and later, set the video PLL as parent for the LDB clock branch. On revision 1.0, the video PLL is useless due to missing dividers, so keep the default parent (mmdc_ch1_axi). Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
-
Philipp Zabel authored
Query silicon revision to determine clock tree and add post dividers for newer revisions. Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
-
Philipp Zabel authored
Use imx_clk_mux_flags and imx_clk_divider_flags to set the appropriate flags for the LDB display interface divider and selector clocks. Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
-
Philipp Zabel authored
Use imx_clk_mux_flags and imx_clk_divider_flags to set the appropriate flags for the LDB display interface divider and selector clocks. Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
-
Philipp Zabel authored
The default is for dividers to set CLK_SET_PARENT_RATE and for muxes to not set that flag. In the LDB clock tree, we need the opposite, so add functions to create divider and mux clocks with configurable flags. Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
-
Philipp Zabel authored
So it can be used in clk-imx6q.c for revision dependent clock tree setup. Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
-
Markus Pargmann authored
There are some config options not selected by imx27 and imx5 that are necessary to use the cpufreq-cpu0 driver. Signed-off-by: Markus Pargmann <mpa@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
-
Philipp Zabel authored
This patch adds the missing GPU2D and GPU3D mux and gate clocks, and the graphics arbiter gate clock. Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
-
Fabio Estevam authored
Fix the following sparse warnings: arch/arm/mach-imx/anatop.c:56:6: warning: symbol 'imx_anatop_pre_suspend' was not declared. Should it be static? arch/arm/mach-imx/anatop.c:62:6: warning: symbol 'imx_anatop_post_resume' was not declared. Should it be static? arch/arm/mach-imx/anatop.c:68:6: warning: symbol 'imx_anatop_usb_chrg_detect_disable' was not declared. Should it be static? arch/arm/mach-imx/anatop.c:78:5: warning: symbol 'imx_anatop_get_digprog' was not declared. Should it be static? arch/arm/mach-imx/anatop.c:86:13: warning: symbol 'imx_anatop_init' was not declared. Should it be static? Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
-
Anson Huang authored
RBC is to control whether some ANATOP sub modules can enter lpm mode when SOC is into STOP mode, if RBC is enabled and PMIC_VSTBY_REQ is set, ANATOP will have below behaviors: 1. Digital LDOs(CORE, SOC and PU) are bypassed; 2. Analog LDOs(1P1, 2P5, 3P0) are disabled; As the 2P5 is necessary for DRAM IO pre-drive in STOP mode, so we need to enable weak 2P5 in STOP mode when 2P5 LDO is disabled. For RBC settings, there are some rules as below due to hardware design: 1. All interrupts must be masked during operating RBC registers; 2. At least 2 CKIL(32K) cycles is needed after the RBC setting is changed. Signed-off-by: Anson Huang <b20788@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
-
Anson Huang authored
Enable periphery charge pump for well biasing at suspend to reduce periphery leakage. Signed-off-by: Anson Huang <b20788@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
-
Anson Huang authored
Anatop module have sereval configurations for user to reduce the power consumption in suspend, provide suspend/resume interface for further use and enable fet_odrive to reduce CORE LDO leakage during suspend. As we have a common anatop file, remove all the operations of anatop module in other files, use anatop interfaces to do that. Signed-off-by: Anson Huang <b20788@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
-
Shawn Guo authored
-
Shawn Guo authored
The imx cleanup for 3.10: * Clean up a couple of unneeded function declarations * Remove imx specific cpufreq driver as generic cpufreq-cpu0 works well as the replacement * Remove platform ahci support * Clean up unused ARCH/MACH Kconfig symbols * Remove a couple of unused files
-
Shawn Guo authored
The imx fixes for 3.9, take 5: * A couple imx35 clock fixes for regressions caused by common clock framework conversion. The admux and iomux get disabled by common clock framework late initcall, and hence causes problems. * Add missing twd clock lookup in device tree. This becomes required since commit bd603455 (ARM: use device tree to get smp_twd clock) forces all DT boot to find lookup from device tree. * Fix imx6q ldb_di clock parents mismatch per reference manual.
-
Dan Carpenter authored
"rstc" is NULL here and we should use "rcdev" instead of "rstc->rcdev". Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
-
Philipp Zabel authored
This adds a simple API for devices to request being reset by separate reset controller hardware and implements the reset signal device tree binding. Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Reviewed-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Shawn Guo <shawn.guo@linaro.org> Reviewed-by: Marek Vasut <marex@denx.de> Reviewed-by: Pavel Machek <pavel@ucw.cz>
-
Stephen Warren authored
This binding is intended to represent the hardware reset signals present internally in most IC (SoC, FPGA, ...) designs. It consists of a binding for a reset controller device (provider), and a pair of properties, "resets" and "reset-names", to link a device node (consumer) to its reset controller via phandle, similarly to the clock and interrupt bindings. The reset controller has all information necessary to reset the consumer device. That could be provided via device tree, or it could be implemented in hardware. The aim is to enable device drivers to request a framework API to issue a reset simply by providing their struct device pointer as the most common case. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Reviewed-by: Shawn Guo <shawn.guo@linaro.org> Reviewed-by: Marek Vasut <marex@denx.de> Reviewed-by: Pavel Machek <pavel@ucw.cz> Acked-by: Rob Herring <rob.herring@calxeda.com>
-
- 09 Apr, 2013 6 commits
-
-
Paul Bolle authored
This removes the unused Kconfig options ARCH_MX5, ARCH_MX51, ARCH_MX53 and MACH_MX21. Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
-
Sascha Hauer authored
The i.MX53 ahci platform support is unused in mainline. To demotivate people using it just remove it from the tree. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
-
Dirk Behme authored
According to the recent i.MX6 Quad technical reference manual, mode 0x4 (100b) of the CCM_CS2DCR register (address 0x020C402C) bits [11-9] and [14-12] select the PLL3 clock, and not the PLL3 PFD1 540M clock. In our code, the PLL3 root clock is named 'pll3_usb_otg', select this instead of the 540M clock. Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
-
Shawn Guo authored
While booting from device tree, imx6q used to provide twd clock lookup by calling clk_register_clkdev() in clock driver. However, the commit bd603455 (ARM: use device tree to get smp_twd clock) forces DT boot to look up the clock from device tree. It causes the failure below when twd driver tries to get the clock, and hence kernel has to calibrate the local timer frequency. smp_twd: clock not found -2 ... Calibrating local timer... 396.13MHz. Fix the regression by providing twd clock lookup from device tree, and remove the unused twd clk_register_clkdev() call from clock driver. Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
-
Markus Pargmann authored
The admux clock seems to be the audmux clock as tests show. audmux does not work without this clock enabled. Currently imx35 does not register a clock device for audmux. This patch adds this registration. imx-audmux driver already handles a clock device, so no changes are necessary there. Signed-off-by: Markus Pargmann <mpa@pengutronix.de> Cc: stable@vger.kernel.org Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
-
Markus Pargmann authored
This patch enables iomuxc_gate clock. It is necessary to be able to reconfigure iomux pads. Without this clock enabled, the clk_disable_unused function will disable this clock and the iomux pads are not configurable anymore. This happens at every boot. After a reboot (watchdog system reset) the clock is not enabled again, so all iomux pad reconfigurations in boot code are without effect. The iomux pads should be always configurable, so this patch always enables it. Signed-off-by: Markus Pargmann <mpa@pengutronix.de> Cc: stable@vger.kernel.org Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
-
- 08 Apr, 2013 1 commit
-
-
Linus Torvalds authored
-
- 07 Apr, 2013 1 commit
-
-
git://git.kernel.org/pub/scm/virt/kvm/kvmLinus Torvalds authored
Pull KVM fix from Gleb Natapov: "Bugfix for the regression introduced by commit c300aa64" * git://git.kernel.org/pub/scm/virt/kvm/kvm: KVM: Allow cross page reads and writes from cached translations.
-