Initialize mtd->writebufsize to the value obtained
by CFI query command at probe time.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

This field will be used to indicate the write buffer size
of the MTD device. UBI will set it's minimal I/O unit size
(min_io_size) to the indicated write buffer size. By this
change we intend to fix failed recovery of UBIFS partitions
we currently observe on NOR flash when mounting the partition
after unclean unmount.

Currently the min_io_size is set to mtd->writesize (which is 1
byte for NOR flash). But flash programming is often done from
prepared write buffer containing multiple bytes and is performed
in one programming operation which could be interrupted by a power
cut or a system reset causing corrupted (partially written) areas
in a flash sector. Knowing the size of potentially corrupted areas
UBIFS scanning and recovery algorithms are able to perform
successful recovery.

In case of NOR flash minimal I/O size must be equal to the
maximal size of the write buffer used by embedded flash
programming algorithm. In case of NAND flash mtd->writebufsize
should be equivalent to mtd->writesize.

The subsequent patches will add mtd->writebufsize initialization
where needed.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Prevent OneNAND's voltage regulator from going to sleep while
OneNAND is in use, by explicitly enabling and disabling the
regulator as appropriate.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Add enable / disable methods called from get_device() / release_device().
These can be used, for example, to allow the driver to prevent the voltage
regulator from being put to sleep while OneNAND is in use.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

The last byte of the ID should be zero for this chip. Was added in
commit d0e8c47c . Reported by Tomi
Varjo.
Signed-off-by: Aleksandr Koltsoff <aleksandr.koltsoff@ebts.fi>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

See commit: c0cbfd0e
Using __nand_correct_data() helper function, this driver can read 512
byte (with 6 byte ECC) at a time.

This is correct, but not more:
With NAND chips providing page sizes > 512 Bytes
chip->ecc.bytes are calculated > 6 in txx9ndfmc_nand_scan.
According the data sheet there are (only) 6 bytes ECC available.

After applying the patch a Hynix 512M*8 with 2KiB page size could be
successfully formatted and used with an ubifs file system.
Signed-off-by: Ralf Roesch <ralf.roesch@rw-gmbh.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Acked-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

These chips report CFI v3.3 [1], so patch them on the fly to the more
correct v1.3.
Discussed and tested by the OpenWRT people [2].

[1] http://www.samsung.com/global/system/business/semiconductor/product/2007/6/11/NORFlash/32Mbit/K8D3216UBC/ds_K8D3x16UxC_rev17.pdf
[2] https://dev.openwrt.org/ticket/866Signed-off-by: Guillaume LECERF <glecerf@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

These chips report CFI v0.0 [1], so extend cfi_fixup_major_minor()
to patch all Samsung chips from 0.0 to 1.0.
Discussed and tested by the OpenWRT people [2].

[1] http://www.samsung.com/global/system/business/semiconductor/product/2007/6/11/NORFlash/64Mbit/K8D6316UTM/ds_K8D6x16UxM_rev16.pdf
[2] https://dev.openwrt.org/ticket/7348Signed-off-by: Guillaume LECERF <glecerf@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

There is a common requirement for not using OMAP specific omap_readw() /
omap_writew() function calls in drivers/, but replace them with
readw() / writew() on ioremap()ped addresses passed from arch/ instead.

The patch implements this idea for the Amstrad Delta NAND driver. To be
able to use the modified driver, the board file is updated with the
platform device I/O resource declaration, which is passed from there.

Created and tested against linux-2.6.37-rc5, on top of recent patch
'MTD: NAND: ams-delta: convert to platform driver'.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Add a DEBUG(MTD_DEBUG_LEVEL2, ..) trace at beginning of sst_write() function as
it is done in m25p80_write() function.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Now that the Amstrad Delta NAND driver is converted to a platform driver,
which prevents it from interfering with other unrelated hardware in multiple
OMAP1 cpu and machine configurations, it can be automatically configured for
being built into the kernel if the Amstrad Delta board is also selected.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Initial bad blocks are normal but the messages look like
errors.  Make the messages less scary, make the main
message an informational message not a warning, make the
message displaying registers a debug message and include
the address there instead of in the informational message.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Add the ability to parse MTD partition information from the
kernel command line.

Note that a pointless BUG_ON is removed, as are redundant
calls to 'del_mtd_partitions()' and 'del_mtd_device()'
because they are also done by 'onenand_release()'.

Finally note that 'add_mtd_device()' returns 1 on failure
so the error condition was incorrect.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

In checking for the ONFI revision, the first conditional (for checking
"unsupported" ONFI) seems unnecessary.  All ONFI revisions should be
backwards-compatible; even if this is not the case on some newer ONFI
revision, it should simply fail the second version-checking if-else block
(i.e., the bit-fields for 1.0, 2.0, etc. would not be set to 1). Thus, we
move our "unsupported" condition after having checked each bit field.

Also, it's simple enough to add a condition for ONFI revision 2.3. Note
that this does *NOT* mean we handle all new features of ONFI versions
above 1.0.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Florian Fainelli <ffainelli@freebox.fr>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

We have the order of the conditional wrong for choosing the ONFI chip name
vs. the ID table name. Without this fix, we will almost *always* choose a
NULL string to print out instead of the correct one.

This has already been suggested by Matthieu Castet.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Florian Fainelli <ffainelli@freebox.fr>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

In its current form, the driver may interfere with different hardware on
different boards if built into the kernel, hence is not suitable for
inclusion into a defconfig, inteded to be usable with multiple OMAP1 cpu and
machine types.

Convert it to a platform driver, that should be free from this issue.

Created and tested against linux-2.6.37-rc5 on Amstrad Delta.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

flush_scheduled_work() is deprecated and scheduled to be removed.
Directly flush cxt->work_{erase|write} on removal instead.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Original 4KiB pagesize chip (SLC) doesn't support Multi block erase at Spec.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

This reverts commit e14feafb.

The commit limits the maximum amount of bytes which can be read
at one go to the OOB size, which is incorrect, because mtd->read_oob()
allows reading multiple pages at a time, see comment near
"struct mtd_oob_ops" at include/linux/mtd/mtd.h. So this patch
breaks ABI and hence, has to be reverted.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

This bug becomes visible in 2x mode when chip->writesize
is different from mtd->writesize (= 2 * chip->writesize).
At this case the bad block information is read from
the first and the third physical pages instead of
the first and the second as specification states.
Signed-off-by: Roman Tereshonkov <roman.tereshonkov@nokia.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Original 4KiB pagesize chip (SLC) doesn't support OOB operations at Spec.
And it's also same at Flex-OneNAND.

Remove the MLC macro if possible and use 4KiB pagesize macro since MLC has 4KiB pagesize.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Fix spelling in the interface file.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

The FSMC actually has a standard ARM PrimeCell ID register, and
the "revision" part of that register contains the thing that
the code is looking at. Reuse the infrastructure from the AMBA
bus abstraction and rid local defines.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

This removes the PARTITION macro that David didn't like and also
removes a local variable that was dangling unused in some #ifdefs
by being a bit more clever.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Building the kernel with 'make CONFIG_DEBUG_SECTION_MISMATCH=y´

resulted in:

WARNING: vmlinux.o(.data+0x15938): Section mismatch in reference from
the variable sst25l_driver to the function .init.text:sst25l_probe()
The variable sst25l_driver references
the function __init sst25l_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,

Fix the section mismatch.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

If CONFIG_MTD_PARTITIONS is not selected, then the following warning is generated:

  CC      drivers/mtd/nand/mxc_nand.o
drivers/mtd/nand/mxc_nand.c: In function 'mxcnd_probe':
drivers/mtd/nand/mxc_nand.c:1014: warning: unused variable 'nr_parts'

Fix it by marking nr_parts as __maybe_unused.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

This patch should fix the following problem:
 1. the  jffs2-image update in the u-boot was ok
 2. first restart and first mount of the NAND-flash-partition was also ok
 3. before the restart of controller there are no any activity on NAND-flash except of the jffs2_gcd_mtdX-process ...
 4. BUT after the second restart the NAND-flash-partition could not be really used after the second mount,
    dmesg filled with messages:
...
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x03ce0000: 0xc0ff instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x03d00000: 0xc0ff instead
....
Just for for info:
the behaviour observed on mpc8313-based board with the large-page NAND.
The only activity on NAND-flash was the garbage collector process, that looks for CLEANMARKER-nodes

As Scott said it was broken by commit 3ab8f2a2Signed-off-by: Sergej Stepanov <Sergej.Stepanov@ids.de>
--
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Function mtd_has_master renamed as mtd_is_partition to follow the function logic.
The patch fixes the problem of checking the right mtd device for partition creation.
To delete partition checking is not needed here so as it is done in mtd_del_partition.
By master we consider the mtd device which does not belong to any partition.
Signed-off-by: Roman Tereshonkov <roman.tereshonkov@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

When run mtd_oobtest case, there will be one error for step(4),
which turned out it need add one check for out of page read in
nand_do_read_oob just like mtd_do_write_oob did it already.
This commit also fix one typo error for comments in mtd_do_write_oob
Signed-off-by: Jason Liu <r64343@freescale.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Warning(include/linux/mtd/nand.h:543): No description found for parameter 'badblockbits'
Warning(drivers/mtd/nand/nand_bbt.c:1101): No description found for parameter 'mtd'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc:	David Woodhouse <dwmw2@infradead.org>
Cc:	linux-mtd@lists.infradead.org
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

The 'param' parameter has never been used since its introduction, so
simply remove it.
Signed-off-by: Guillaume LECERF <glecerf@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

It says FB instead of FS (file system).
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

do_verify_xattr_datum(), do_load_xattr_datum(), load_xattr_datum()
and verify_xattr_ref() should return negative value on error.
Sometimes they return EIO that is positive.  Change this to -EIO.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Using %pR standardizes the struct resource output.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Using %pR standardizes the struct resource output.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Now that the mtd core supports more then 64 ecc bytes we can use it instead of
some a custom hack in the jz4740 nand driver.
This patch removes the custom {read,write}_page handlers from the jz4740 nand
driver. Thus the driver will now fallback to the default handlers from the nand
core.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

The [vk][cmz]alloc(_node) family of functions return void pointers which
it's completely unnecessary/pointless to cast to other pointer types since
that happens implicitly.

This patch removes such casts from drivers/mtd/
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>