Convert DEBUGOUTx to pr_debug
Convert DEBUGFUNC to more commonly used ENTER
Convert mac address output to %pM
Use #define pr_fmt
Convert a few printks to pr_<level>
Improve ixgb_mc_addr_list_update: use a temporary for current mc address
Use etherdevice.h functions for mac address testing
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a small race between when the tx queues are stopped
and when netif_carrier_off() is called in ixgbe_down.  If the
dev_watchdog() timer fires during this time it is possible for
a false tx timeout to occur.

This patch moves the netif_carrier_off() so that it is called before
the tx queues are stopped preventing the dev_watchdog timer from
detecting false tx timeouts.  The race is seen occosionally when
FCoE or DCB settings are being configured or changed.

Testing note, running ifconfig up/down will not reproduce this
issue because dev_open/dev_close call dev_deactivate() and then
dev_activate().
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This change corrects the fact that we were not reporting Gen2 link speeds
when we were in fact connected at Gen2 rates.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

writebacks can be held indefinitely by hardware if EITR=0, when
combined with TXDCTL.WTHRESH=8.  When EITR=0, WTHRESH should be
set back to zero.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

82598/82599 can support EITR == 0, which allows for the
absolutely lowest latency setting in the hardware.  This disables
writeback batching and anything else that relies upon a delayed
interrupt. This patch enables the feature of "override" when a
user sets rx-usecs to zero, the driver will respect that setting
over using RSC, and automatically disable RSC.  If rx-usecs is
used to set the EITR value to 0, then the driver should disable
LRO (aka RSC) internally until EITR is set to non-zero again.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no need to increment nr_frags because skb_fill_page_desc increments
it.
Signed-off-by: Koki Sanagi <sanagi.koki@jp.fujitsu.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no need to increment nr_frags because skb_fill_page_desc increments
it.
Signed-off-by: Koki Sanagi <sanagi.koki@jp.fujitsu.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

__sk_dst_set() might be called while no state can be integrated in a
rcu_dereference_check() condition.

So use rcu_dereference_raw() to shutup lockdep warnings (if
CONFIG_PROVE_RCU is set)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

const qualifier on sock argument is misleading, since we can modify rxhash.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RFC 1122 says the following:
...
  Keep-alive packets MUST only be sent when no data or
  acknowledgement packets have been received for the
  connection within an interval.
...

The acknowledgement packet is reseting the keepalive
timer but the data packet isn't. This patch fixes it by
checking the timestamp of the last received data packet
too when the keepalive timer expires.
Signed-off-by: Flavio Leitner <fleitner@redhat.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>

I prefer that the hlist be only accessed through the hlist macro
objects. Explicit twiddling of links (especially with RCU) exposes
the code to future bugs.

Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use existing inline function.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	drivers/net/e100.c
	drivers/net/e1000e/netdev.c

Calls to twsk_net() are in some cases protected by reference counting
as an alternative to RCU protection.  Cases covered by reference counts
include __inet_twsk_kill(), inet_twsk_free(), inet_twdr_do_twkill_work(),
inet_twdr_twcal_tick(), and tcp_timewait_state_process().  RCU is used
by inet_twsk_purge().  Locking is used by established_get_first()
and established_get_next().  Finally, __inet_twsk_hashdance() is an
initialization case.

It appears to be non-trivial to locate the appropriate locks and
reference counts from within twsk_net(), so used rcu_dereference_raw().
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In some Power7 platforms, when using VIOS (Virtual I/O Server), we
need to wait longer for control packets to finish transfer during
initialization.
Without this change, initialization may fail prematurely.
Signed-off-by: Wen Xiong <wenxiong@us.ibm.com>
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Acked-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Prompted by a previous patch submitted by Matthew Garret <mjg@redhat.com>,
further digging into errata documentation reveals the current enabling or
disabling of ASPM L0s and L1 states for certain parts supported by this
driver are incorrect.  82571 and 82572 should always disable L1.  For
standard frames, 82573/82574/82583 can enable L1 but L0s must be disabled,
and for jumbo frames 82573/82574 must disable L1.  This allows for some
parts to enable L1 in certain configurations leading to better power
savings.

Also according to the same errata, Early Receive (ERT) should be disabled
on 82573 when using jumbo frames.

Cc: Matthew Garret <mjg@redhat.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The PHY laser is still on during driver init.  It's allowing
garbage to hit our FIFO, which eventually can cause the entire
device to die.  Power down the laser while setting up the device,
and re-enable the laser before getting link.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Based upon a report from Stephen Rothwell:

--------------------
net/bridge/br_multicast.c: In function 'br_ip6_multicast_alloc_query':
net/bridge/br_multicast.c:469: error: implicit declaration of function 'csum_ipv6_magic'

Introduced by commit 08b202b6 ("bridge
br_multicast: IPv6 MLD support") from the net tree.

csum_ipv6_magic is declared in net/ip6_checksum.h ...
--------------------
Signed-off-by: David S. Miller <davem@davemloft.net>

78f1cd02 ("fix broken register writes")
does not work for Al Viro's r8169 (XID 18000000).
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Few (6) network drivers enable mwi explicitly. Fewer worry about a
failure.

It is not a fix but it should avoid some annoyance like
http://bugzilla.kernel.org/show_bug.cgi?id=15454Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Conrad Kostecki <conikost@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Even with commit 32dec5dd ("bridge
br_multicast: Don't refer to BR_INPUT_SKB_CB(skb)->mrouters_only
without IGMP snooping."), BR_INPUT_SKB_CB(skb)->mrouters_only is
not appropriately initialized if IGMP/MLD snooping support is
compiled and disabled, so we can see garbage.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Even with commit 32dec5dd ("bridge
br_multicast: Don't refer to BR_INPUT_SKB_CB(skb)->mrouters_only
without IGMP snooping."), BR_INPUT_SKB_CB(skb)->mrouters_only is
not appropriately initialized if IGMP snooping support is
compiled and disabled, so we can see garbage.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Trying to run izlisten (from lowpan-tools tests) on a device that does not
exists I got the oops below. The problem is that we are using get_dev_by_name
without checking if we really get a device back. We don't in this case and
writing to dev->type generates this oops.

[Oops code removed by Dmitry Eremin-Solenikov]

If possible this patch should be applied to the current -rc fixes branch.
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit aa395145 (net: sk_sleep() helper) missed three files in the
conversion.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As in for example pppoe introduce phonet_pernet and use it instead of calling
net_generic directly.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tg3: Fix INTx fallback when MSI fails

MSI setup changes the value of irq_vec in struct tg3 *tp.
This attribute must be taken into account and restored before
we try to do a new request_irq for INTx fallback.

In powerpc, the original code was leading to an EINVAL return within
request_irq, because the driver was trying to use the disabled MSI
virtual irq number instead of tp->pdev->irq.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit fda48a0d (tcp: bind() fix when many ports are bound)
introduced a bug on IPV6 part.
We should not call ipv6_addr_any(inet6_rcv_saddr(sk2)) but
ipv6_addr_any(inet6_rcv_saddr(sk)) because sk2 can be IPV4, while sk is
IPV6.
Reported-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Stay consistent with other functions and with comment also and name
pernet_operations parameter properly.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

optimize rps_get_cpu().

don't initialize ports when we can get the ports. one memory access
for ports than two.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Nothing stops the workqueue being left to run in parallel with close or a
few other operations. This causes double unmaps and the like.

See kerneloops.org #1041230 for an example
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sky2 hardware supports hardware receive hash calculation.
Now that Receive Packet Steering is available, add support
to enable it.

This version does not depend on CONFIG_RPS. Also set_flags rejects
all values except RXHASH, so driver won't have to change next time
somebody adds a new one.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'net-next-2.6_20100423a/br/br_multicast_v3' of git://git.linux-ipv6.org/gitroot/yoshfuji/linux-2.6-next

Finally add support to detect a local IPV6_DONTFRAG event
and return the relevant data to the user if they've enabled
IPV6_RECVPATHMTU on the socket.  The next recvmsg() will
return no data, but have an IPV6_PATHMTU as ancillary data.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add dontfrag argument to relevant functions for
IPV6_DONTFRAG support, as well as allowing the value
to be passed-in via ancillary cmsg data.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add underlying data structure changes and basic setsockopt()
and getsockopt() support for IPV6_RECVPATHMTU, IPV6_PATHMTU,
and IPV6_DONTFRAG.  IPV6_PATHMTU is actually fully functional
at this point.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since .size is set properly in "struct pernet_operations l2tp_eth_net_ops",
allocating space for "struct l2tp_eth_net" by hand is not correct, even causes
memory leakage.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since .size is set properly in "struct pernet_operations l2tp_net_ops",
allocating space for "struct l2tp_net" by hand is not correct, even causes
memory leakage.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

gianfar driver may pass NULL pointer to the of_translate_address(),
which may lead to a kernel oops. Fix this by using of_iomap(), which
is also much simpler and shorter.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Old P1020RDB device trees were not specifing tbipa address for
MDIO nodes, which is now causing this kernel oops:

 ...
 eth2: TX BD ring size for Q[6]: 256
 eth2: TX BD ring size for Q[7]: 256
 Unable to handle kernel paging request for data at address 0x00000000
 Faulting instruction address: 0xc0015504
 Oops: Kernel access of bad area, sig: 11 [#1]
 ...
 NIP [c0015504] memcpy+0x3c/0x9c
 LR [c000a9f8] __of_translate_address+0xfc/0x21c
 Call Trace:
 [df839e00] [c000a94c] __of_translate_address+0x50/0x21c (unreliable)
 [df839e50] [c01a33e8] get_gfar_tbipa+0xb0/0xe0
 ...

The old device trees are buggy, though having a dead ethernet is
better than a dead kernel, so fix the issue by using of_iomap().

Also, a somewhat similar issue exist in the probe() routine, though
there the oops is only a possibility. Nonetheless, fix it too.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>