- 27 Nov, 2012 4 commits
-
-
Fabio Baltieri authored
This adds hrefprev60, hrefv60plus and ccu9540 to device trees compiled during build. Acked-by:
Linus Walleij <linus.walleij@linaro.org> Acked-by:
Lee Jones <lee.jones@linaro.org> Signed-off-by:
Fabio Baltieri <fabio.baltieri@linaro.org>
-
Lee Jones authored
We now initialise the PCM driver through the MSP DAI, so there is no need to register it though platform code anymore. This patch strips out all PCM platform registration. Acked-by:
-
Lee Jones authored
GPIO numbers for the newly created gpio-regulator will differ from board to board. Therefore it's not sensible to leave this information in the top level DTSI file. Let's move them out to the DTS files where they can correctly vary. Acked-by:
-
Lee Jones authored
Not all supported boards will require a MMCI gpio-regulator, therefore it's a good idea to only enable the node when and if it is required. Let's disable it by default. Acked-by:
-
- 20 Nov, 2012 7 commits
-
-
Lee Jones authored
UARTs no longer require call-back information, since the reset call-back was removed in 43b5f0d6. The only AUXDATA dependencies remaining for UARTs are DMA settings. Acked-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Lee Jones authored
The u9540 supports 3 MMC devices. This patch enables two of them and updates the configuration of the already enabled SDI4 port. Acked-by:
-
Lee Jones authored
Here we add the device node for the SDI4 (MMC) port to the u9540 Device Tree source file. This will allow successful probing of the internal MMC storage device when booting with DT enabled. Acked-by:
-
Lee Jones authored
Add the 3 UART nodes required to enable serial ports on the u9540. Acked-by:
-
Lee Jones authored
This patch sees the creation of a sparse Device Tree file for ST-Ericsson's latest development board supporting the latest dual-core Cortex-a9 u9540 SoC. Acked-by:
-
Lee Jones authored
Here we add the Device Tree nodes which are required to successfully probe the MMCI driver which will enable the four cards available on ST-Ericsson's HREF hardware development platform. Acked-by:
-
Lee Jones authored
Regulator supply names should be allocated by board rather than per SoC, as the same SoC could be wired differently on varying hardware. Here we push all regulator-name allocation out to the dbx5x0 subordinate board files; HREF and Snowball. Requested-by:
Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by:
-
- 01 Nov, 2012 29 commits
-
-
Lee Jones authored
The Device Tree machine description for the ux5x0 was moved recently and as a consequence missed the addition of SMP operations. Without this patch SMP doesn't work and only one CPU is present after booting. Acked-by:
-
Lee Jones authored
It is the intention to convert the MMC voltage changing from GPIO flipping to using a proper GPIO regulator interface. A prerequisite of that is to enable the GPIO regulator functionality. As this affects all ux5x0 based boards we'll do it here instead of in the Kconfigs. Acked-by:
-
Lee Jones authored
On boot the Nomadik GPIO controller complains that an IRQ can't be configured as active high level-sensitive, so this patch converts it to be low-to-high edge triggered instead. Acked-by:
-
Lee Jones authored
There is a very simple mechanism to change and SDI's voltage which consists of toggling some GPIOs. This scenario can be better handled if we convert it to a GPIO regulator. This patch provides one which can be read from Device Tree. Acked-by:
-
Lee Jones authored
So far, each ST-Ericsson board supported by Device Tree has been similar enough to run though a single DT_MACHINE_INIT call. On the back of that it has been suggested that we should reduce the number of compatible strings in our dt_compat structure. After subsequent discussion with Arnd Bergmann the conclusion was to list entries by platform as opposed to by board. The other suggestion was to use a single string which would cover all supported platforms, but any wildcard entries would include unsupported chipsets, such as the u5500 and potential new chips which no not yet have DT functionality. Hence, the best solution which encompasses all supported platforms, but no unsupported ones was to list the currently enabled four chipsets; u8500, u8540, u9500 and u9540 instead. Acked-by:
-
Lee Jones authored
The u8500 and u9540 DT_MACHINE_START calls are almost identical at the moment, referencing exactly the same function pointers. Until this changes we may as well convert the original one to be more generic and use that instead. Acked-by:
-
Lee Jones authored
When enabling ST-Ericsson's ccu9540 development board the board's full name has not been used. This patch adapts all references of the board's short name to how it should be referenced. Reviewed-by:
-
Lee Jones authored
The u9540 supports 3 MMC devices. This patch enables two of them and updates the configuration of the already enabled SDI4 port. Acked-by:
-
Lee Jones authored
Here we add the device node for the SDI4 (MMC) port to the u9540 Device Tree source file. This will allow successful probing of the internal MMC storage device when booting with DT enabled. Acked-by:
-
Lee Jones authored
Add the 3 UART nodes required to enable serial ports on the u9540. Acked-by:
-
Lee Jones authored
First level board support for the u9540. Acked-by:
-
Lee Jones authored
This patch sees the creation of a sparse Device Tree file for ST-Ericsson's latest development board supporting the latest dual-core Cortex-a9 u9540 SoC. Acked-by:
-
Lee Jones authored
'st-ericsson,u8500' is too much of a broad name to be used for any of the supported development boards supported by ST-Ericsson. As such it was never used. It has no place to remain in the board compatible list, hence why it's being removed. Acked-by:
-
Lee Jones authored
This patch allows the STMPE keypad driver to be successfully probed and initialised during a Device Tree enabled boot sequence. It contains all of the required properties needed to setup and map each key on the 6x3 keypad located on the ST User Interface Board. Acked-by:
-
Lee Jones authored
Here we apply the STMPE Multi-Functional Device's node to the ST User Interface Board Device Tree file. It includes all of the properties required for correct device initialsation. Acked-by:
-
Lee Jones authored
The regulator_has_full_constraints() call is not required if we are booting with Device Tree as it's assumed in this case. Acked-by:
-
Lee Jones authored
It is possible to connect a BU21013 Touch Screen to all version of the HREF which support the ST-UIB. This patch applies all the necessary settings to the pre-v60 and v60+ HREF Device Trees. Acked-by:
-
Lee Jones authored
As there will be a Device Tree created for the UIBs, there is no need to call the UIB initiation functions. Each device will be detailed and registered from the Device Tree instead. Acked-by:
-
Lee Jones authored
This is a skeleton creation which will be populated with the devices found on one of ST-Ericsson's (UIB) User Interface Board. Acked-by:
-
Lee Jones authored
Here we apply required documentation for the Rohm BU21013 Touch Screen driver which describe available properties and how to use them. Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com> Cc: linux-input@vger.kernel.org Cc: devicetree-discuss@lists.ozlabs.org Acked-by:
-
Lee Jones authored
We're currently carrying two 'struct bu21013_platform_device's which are identical for no apparent reason. Here we remove the extra burden and apply the same information to the two different instances of the bu21012_tp driver registration. Acked-by:
-
Lee Jones authored
To aid the kernel in its effort to move to DT only booting, we're transplanting all Device Tree related code to cpu-db8500 which will remain persistent throughout the transition. This change paths the way for complete removal of board-mop500, which will be done once the all DMA settings are moved into the respective DT source files. Acked-by:
-
Lee Jones authored
Most devices have now been successfully DT:ed and each supported platform has its own Device Tree source file. Hence the majority of the platform specific device registration calls can now be successfully removed. Acked-by:
-
Lee Jones authored
Here we ensure the SFH7741 Proximity Sensor is registered through gpio-keys when booting with Device Tree enabled. Acked-by:
-
Lee Jones authored
In ux500 platform code we currently support a number of devices. Two of these devices are fairly similar, but have key differences. Early (pre-v60) HREFs and the more up-to-date versions (v60+), and they both need to be supported by Device Tree. Here we apply a DT source file for the earlier versions. Acked-by:
-
Lee Jones authored
There are two main versions of the ST-Ericsson hardware reference board, each with subtle differences. These versions are described in current platform data as 'mop500' for HREF v1.1 & v2.0 and 'hrefv60+' for latter incarnations. However, the boards have much in common, so this patch creates a .dtsi (Device Tree Source Include) file which describes the similarities between the two boards and individual 'hrefprev60' and 'hrefv60plus' .dts files which depict the differences. Acked-by:
-
Lee Jones authored
Snowball's external SD/MMC slot is only capable of 4 bit data transfer, not 8 bits as previously thought. This is a simple fixup moving to the correct settings. Acked-by:
-
Lee Jones authored
Here we add the Device Tree nodes which are required to successfully probe the MMCI driver which will enable the four cards available on ST-Ericsson's HREF hardware development platform. Acked-by:
-
Lee Jones authored
In the DB8500 Reference Manual SDI devices are described as being part of peripheral blocks. This is more in line with how these devices are actually represented in hardware, so here we detail which peripheral block each of the SDI devices belong in the node name. Requested-by:
-
