- 14 May, 2018 2 commits
-
-
Sean Young authored
A mceusb device has been observed producing invalid irdata. Proactively guard against this. Suggested-by:
Matthias Reichl <hias@horus.com> Signed-off-by:
Sean Young <sean@mess.org> Signed-off-by:
Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-
Sean Young authored
If the IR timeout is set on vid 1784 pid 0011, the device starts behaving strangely. Reported-by:
-
- 11 May, 2018 23 commits
-
-
Mauro Carvalho Chehab authored
This is a core media file... it shoudn't have so many coding style issues! The last patch ended by being submitted with an error like that, very likely due to some cut and paste issue. Maybe it is time to clean it up. Do it with the auto fix logic: ./scripts/checkpatch.pl -f drivers/media/dvb-core/dvb_frontend.c --strict --fix-inplace Then manually fix the errors introduced by it. Signed-off-by: -
Max Kellermann authored
During destruction, a race condition in dvb_media_controller_disable_source() can cause a kernel crash, because the "mdev" pointer has been read successfully while another task executes dvb_usb_media_device_unregister(), which destroys the object. Example for such a crash: general protection fault: 0000 [#1] SMP CPU: 1 PID: 301 Comm: vdr Not tainted 4.8.1-nuc+ #102 [142B blob data] task: ffff8802301f2040 task.stack: ffff880233728000 RIP: 0010:[<ffffffff816c296b>] [<ffffffff816c296b>] dvb_frontend_release+0xcb/0x120 RSP: 0018:ffff88023372bdd8 EFLAGS: 00010202 RAX: 001fd55c000000da RBX: ffff880236bad810 RCX: 0000000000000000 RDX: ffff880235bd81f0 RSI: 0000000000000246 RDI: ffff880235bd81e8 RBP: ffff88023372be00 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: ffff88022f009910 R12: 0000000000000000 R13: ffff880235a21a80 R14: ffff880235bd8000 R15: ffff880235bb8a78 FS: 0000000000000000(0000) GS:ffff88023fd00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f96edd69818 CR3: 0000000002406000 CR4: 00000000001006e0 Stack: ffff88022f009900 0000000000000008 ffff880235bb8a78 ffff8802344fbb20 ffff880236437b40 ffff88023372be48 ffffffff8117a81e ffff880235bb8a78 ffff88022f009910 ffff8802335a7400 ffff8802301f2040 ffff88022f009900 Call Trace: [<ffffffff8117a81e>] __fput+0xde/0x1d0 [<ffffffff8117a949>] ____fput+0x9/0x10 [<ffffffff810a9fce>] task_work_run+0x7e/0xa0 [<ffffffff81094bab>] do_exit+0x27b/0xa50 [<ffffffff810407e3>] ? __do_page_fault+0x1c3/0x430 [<ffffffff81095402>] do_group_exit+0x42/0xb0 [<ffffffff8109547f>] SyS_exit_group+0xf/0x10 [<ffffffff8108bedb>] entry_SYSCALL_64_fastpath+0x13/0x8f Code: 31 c9 49 8d be e8 01 00 00 ba 01 00 00 00 be 03 00 00 00 e8 68 2d a0 ff 48 8b 83 10 03 00 00 48 8b 80 88 00 00 00 48 85 c0 74 12 <48> 8b 80 88 02 00 00 48 85 c0 74 06 49 8b 7d RIP [<ffffffff816c296b>] dvb_frontend_release+0xcb/0x120 [mchehab+samsung@kernel.org: fix a Coding Style issue] Signed-off-by:Max Kellermann <max.kellermann@gmail.com> Signed-off-by:
-
Hans Verkuil authored
Add missing 'inline' to fix this compiler warning: In file included from drivers/media/common/b2c2/flexcop-fe-tuner.c:21:0: drivers/media/dvb-frontends/lgdt330x.h:61:22: warning: 'lgdt330x_attach' defined but not used [-Wunused-function] struct dvb_frontend *lgdt330x_attach(const struct lgdt330x_config *config, ^~~~~~~~~~~~~~~ Signed-off-by:Hans Verkuil <hansverk@cisco.com> Suggested-by:
-
Niklas Söderlund authored
When refactoring the Gen3 enablement series crop and compose handling where broken. This went unnoticed but can result in writing out side the capture buffer. Fix this by restoring the crop and compose to reflect the format dimensions as we have not yet enabled the scaler for Gen3. Fixes: 5e7c6236 ("media: rcar-vin: use different v4l2 operations in media controller mode") Reported-by:
Jacopo Mondi <jacopo+renesas@jmondi.org> Signed-off-by:
Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Signed-off-by:
-
Niklas Söderlund authored
The offending commit was an attempt to fix the issue of writing outside the capture buffer for VIN Gen3. Unfortunately it only fixed the symptom of the problem to such a degree I could no longer reproduce it. Revert the offending commit before a proper fix can be added in a follow-up patch. This reverts commit 015060cb. Signed-off-by:
-
Colin Ian King authored
Trivial fix to spelling mistake in dprintk message text Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
Anders Roxell authored
cx231-417 uses kmalloc/kfree functions, so slab header needs to be included in order to fix the following build errors: drivers/media/usb/cx231xx/cx231xx-417.c: In function ‘cx231xx_bulk_copy’: CC drivers/media/platform/qcom/venus/firmware.o drivers/media/usb/cx231xx/cx231xx-417.c:1389:11: error: implicit declaration of function ‘kmalloc’; did you mean ‘vmalloc’? [-Werror=implicit-function-declaration] buffer = kmalloc(buffer_size, GFP_ATOMIC); ^~~~~~~ vmalloc drivers/media/usb/cx231xx/cx231xx-417.c:1389:9: warning: assignment makes pointer from integer without a cast [-Wint-conversion] buffer = kmalloc(buffer_size, GFP_ATOMIC); ^ drivers/media/usb/cx231xx/cx231xx-417.c:1400:2: error: implicit declaration of function ‘kfree’; did you mean ‘vfree’? [-Werror=implicit-function-declaration] kfree(buffer); ^~~~~ vfree drivers/media/usb/cx231xx/cx231xx-417.c: In function ‘mpeg_open’: drivers/media/usb/cx231xx/cx231xx-417.c:1713:7: error: implicit declaration of function ‘kzalloc’; did you mean ‘vzalloc’? [-Werror=implicit-function-declaration] fh = kzalloc(sizeof(*fh), GFP_KERNEL); ^~~~~~~ vzalloc drivers/media/usb/cx231xx/cx231xx-417.c:1713:5: warning: assignment makes pointer from integer without a cast [-Wint-conversion] fh = kzalloc(sizeof(*fh), GFP_KERNEL); ^ Signed-off-by:Anders Roxell <anders.roxell@linaro.org> Signed-off-by:
-
Christophe JAILLET authored
If 'media_entity_pads_init()' fails, we must free the resources allocated by 'v4l2_ctrl_handler_init()', as already done in the previous error handling path. 'goto' the right label to fix it. Fixes: 9ac0038d ("media: i2c: Add TDA1997x HDMI receiver driver") Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by:
-
Peter Rosin authored
Returning -1 (-EPERM) is not appropriate here, go with -EIO. Signed-off-by:
Peter Rosin <peda@axentia.se> Signed-off-by:
-
Brad Love authored
These two statements are not errors, reduce to appropriate level. Signed-off-by:
Brad Love <brad@nextdimension.cc> Signed-off-by:
-
Colin Ian King authored
Trivial fix to spelling mistake in dev_err message. Signed-off-by:
-
Brad Love authored
Document what these two register calls are doing. Signed-off-by:
-
Brad Love authored
Include some additional useful registers in the output. Signed-off-by:
-
Brad Love authored
This bug affects all of Hauppauge QuadHD boards when used on all Ryzen platforms and some XEON platforms. On these platforms it is possible to error out the RiSC engine and cause it to stall, whereafter the only way to reset the board to a working state is to reboot. This is the fatal condition with current driver: [ 255.663598] cx23885: cx23885[0]: mpeg risc op code error [ 255.663607] cx23885: cx23885[0]: TS1 B - dma channel status dump [ 255.663612] cx23885: cx23885[0]: cmds: init risc lo : 0xffe54000 [ 255.663615] cx23885: cx23885[0]: cmds: init risc hi : 0x00000000 [ 255.663619] cx23885: cx23885[0]: cmds: cdt base : 0x00010870 [ 255.663622] cx23885: cx23885[0]: cmds: cdt size : 0x0000000a [ 255.663625] cx23885: cx23885[0]: cmds: iq base : 0x00010630 [ 255.663629] cx23885: cx23885[0]: cmds: iq size : 0x00000010 [ 255.663632] cx23885: cx23885[0]: cmds: risc pc lo : 0xffe54018 [ 255.663636] cx23885: cx23885[0]: cmds: risc pc hi : 0x00000000 [ 255.663639] cx23885: cx23885[0]: cmds: iq wr ptr : 0x00004192 [ 255.663642] cx23885: cx23885[0]: cmds: iq rd ptr : 0x0000418c [ 255.663645] cx23885: cx23885[0]: cmds: cdt current : 0x00010898 [ 255.663649] cx23885: cx23885[0]: cmds: pci target lo : 0xf85ca340 [ 255.663652] cx23885: cx23885[0]: cmds: pci target hi : 0x00000000 [ 255.663655] cx23885: cx23885[0]: cmds: line / byte : 0x000c0000 [ 255.663659] cx23885: cx23885[0]: risc0: [ 255.663661] 0x1c0002f0 [ write sol eol count=752 ] [ 255.663666] cx23885: cx23885[0]: risc1: [ 255.663667] 0xf85ca050 [ INVALID sol 22 20 19 18 resync 13 count=80 ] [ 255.663674] cx23885: cx23885[0]: risc2: [ 255.663674] 0x00000000 [ INVALID count=0 ] [ 255.663678] cx23885: cx23885[0]: risc3: [ 255.663679] 0x1c0002f0 [ write sol eol count=752 ] [ 255.663684] cx23885: cx23885[0]: (0x00010630) iq 0: [ 255.663685] 0x1c0002f0 [ write sol eol count=752 ] [ 255.663690] cx23885: cx23885[0]: iq 1: 0xf85ca630 [ arg #1 ] [ 255.663693] cx23885: cx23885[0]: iq 2: 0x00000000 [ arg #2 ] [ 255.663696] cx23885: cx23885[0]: (0x0001063c) iq 3: [ 255.663697] 0x1c0002f0 [ write sol eol count=752 ] [ 255.663702] cx23885: cx23885[0]: iq 4: 0xf85ca920 [ arg #1 ] [ 255.663705] cx23885: cx23885[0]: iq 5: 0x00000000 [ arg #2 ] [ 255.663709] cx23885: cx23885[0]: (0x00010648) iq 6: [ 255.663709] 0xf85ca340 [ INVALID sol 22 20 19 18 resync 13 count=832 ] [ 255.663716] cx23885: cx23885[0]: (0x0001064c) iq 7: [ 255.663717] 0x00000000 [ INVALID count=0 ] [ 255.663721] cx23885: cx23885[0]: (0x00010650) iq 8: [ 255.663721] 0x00000000 [ INVALID count=0 ] [ 255.663725] cx23885: cx23885[0]: (0x00010654) iq 9: [ 255.663726] 0x1c0002f0 [ write sol eol count=752 ] [ 255.663731] cx23885: cx23885[0]: iq a: 0xf85c9780 [ arg #1 ] [ 255.663734] cx23885: cx23885[0]: iq b: 0x00000000 [ arg #2 ] [ 255.663737] cx23885: cx23885[0]: (0x00010660) iq c: [ 255.663738] 0x1c0002f0 [ write sol eol count=752 ] [ 255.663743] cx23885: cx23885[0]: iq d: 0xf85c9a70 [ arg #1 ] [ 255.663746] cx23885: cx23885[0]: iq e: 0x00000000 [ arg #2 ] [ 255.663749] cx23885: cx23885[0]: (0x0001066c) iq f: [ 255.663750] 0x1c0002f0 [ write sol eol count=752 ] [ 255.663755] cx23885: cx23885[0]: iq 10: 0xf4fa2920 [ arg #1 ] [ 255.663758] cx23885: cx23885[0]: iq 11: 0x00000000 [ arg #2 ] [ 255.663759] cx23885: cx23885[0]: fifo: 0x00005000 -> 0x6000 [ 255.663760] cx23885: cx23885[0]: ctrl: 0x00010630 -> 0x10690 [ 255.663764] cx23885: cx23885[0]: ptr1_reg: 0x00005980 [ 255.663767] cx23885: cx23885[0]: ptr2_reg: 0x000108a8 [ 255.663770] cx23885: cx23885[0]: cnt1_reg: 0x0000000b [ 255.663773] cx23885: cx23885[0]: cnt2_reg: 0x00000003 Included is checks of the TC_REQ and TC_REQ_SET registers during states of board initialization, reset, DMA start, and DMA stop. If both registers are set, this indicates a stall in the RiSC engine, at which point the bridge error is cleared. A small delay is introduced in stop_dma as well, to allow transfers in progress to finish. After application all models work on Ryzen, occasionally yielding: cx23885_clear_bridge_error: dma in progress detected 0x00000001 0x00000001, clearing Signed-off-by:
-
Brad Love authored
Currently mask is read for pci_status/ts1_status/ts2_status, but otherwise ignored. The masks are now used to determine whether action is warranted. Signed-off-by:
-
Brad Love authored
On Ryzen systems interrupts are occasionally missed: cx23885: cx23885_wakeup: [ffff99b384b83c00/28] wakeup reg=5406 buf=5405 cx23885: cx23885_wakeup: [ffff99b40bf79400/31] wakeup reg=9537 buf=9536 This patch loops up to five times on wakeup, marking any buffers found done. Since the count register is u16, but the vb2 counter is u32, some modulo arithmetic is used to accommodate wraparound and ensure current active buffer is the buffer expected. Signed-off-by:
-
Hans Verkuil authored
The mdev field is only present if CONFIG_MEDIA_CONTROLLER is set. But since we will need to pass the media_device to vb2 and the control framework it is very convenient to just make this field available all the time. If CONFIG_MEDIA_CONTROLLER is not set, then it will just be NULL. Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Acked-by:
Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by:
-
Sami Tolvanen authored
This change removes IOCTL_INFO_STD and adds stub functions where needed using the DEFINE_V4L_STUB_FUNC macro. This fixes indirect call mismatches with Control-Flow Integrity, caused by calling standard ioctls using a function pointer that doesn't match the function type. Signed-off-by:
Sami Tolvanen <samitolvanen@google.com> Signed-off-by:
-
Gustavo Padovan authored
Instead of putting V4L2_CAP_STREAMING and V4L2_CAP_READWRITE everywhere, set device_caps earlier with these values. Signed-off-by:
Gustavo Padovan <gustavo.padovan@collabora.com> Signed-off-by:
-
Gustavo Padovan authored
To better organize the code we concentrate the setting of V4L2_CAP_STREAMING in one place. Signed-off-by:
-
Julia Lawall authored
The data protected is video_out2 and the lock that is released is &video_out2->dma_queue_lock, so it seems that that lock should be taken as well. Signed-off-by:
Julia Lawall <Julia.Lawall@lip6.fr> Reviewed-by:
Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> Signed-off-by:
-
Wei Yongjun authored
Add the missing clk_disable_unprepare() before return from jpu_open() in the software reset error handling case. Signed-off-by:
Wei Yongjun <yongjun_wei@trendmicro.com.cn> Acked-by:
Mikhail Ulyanov <mikhail.ulyanov@cogentembedded.com> Reviewed-by:
-
Jacopo Mondi authored
Add R-Mobile A1 R8A7740 SoC to the list of compatible values for the CEU unit. Signed-off-by:
Rob Herring <robh@kernel.org> Reviewed-by:
Simon Horman <horms+renesas@verge.net.au> Signed-off-by:
-
- 10 May, 2018 4 commits
-
-
Mauro Carvalho Chehab authored
There are two places pointing to an unexisting "m.chehab@kernel.org" email. I never had such email, so, I'm unsure how it ends there. Anyway, it is plain wrong. While here, use my canonical e-mail on a bunch of places that are pointing to another e-mail. The idea is that, from now on, all places will be pointing to the same SMTP server. Signed-off-by: -
Mauro Carvalho Chehab authored
Linux 4.17-rc4 * tag 'v4.17-rc4': (920 commits) Linux 4.17-rc4 KVM: x86: remove APIC Timer periodic/oneshot spikes genksyms: fix typo in parse.tab.{c,h} generation rules kbuild: replace hardcoded bison in cmd_bison_h with $(YACC) gcc-plugins: fix build condition of SANCOV plugin MAINTAINERS: Update Kbuild entry with a few paths Revert "usb: host: ehci: Use dma_pool_zalloc()" platform/x86: Kconfig: Fix dell-laptop dependency chain. platform/x86: asus-wireless: Fix NULL pointer dereference arm64: vgic-v2: Fix proxying of cpuif access KVM: arm/arm64: vgic_init: Cleanup reference to process_maintenance KVM: arm64: Fix order of vcpu_write_sys_reg() arguments MAINTAINERS & files: Canonize the e-mails I use at files media: imx-media-csi: Fix inconsistent IS_ERR and PTR_ERR tools: power/acpi, revert to LD = gcc bdi: Fix oops in wb_workfn() RDMA/cma: Do not query GID during QP state transition to RTR IB/mlx4: Fix integer overflow when calculating optimal MTT size IB/hfi1: Fix memory leak in exception path in get_irq_affinity() IB/{hfi1, rdmavt}: Fix memory leak in hfi1_alloc_devdata() upon failure ... -
Mauro Carvalho Chehab authored
Right now, there are two mutexes serializing r/w ops: one "generic" and another one specifically for stream on/off. Clean it a little bit, getting rid of one of the mutexes. Signed-off-by: -
Mauro Carvalho Chehab authored
As warned by gcc: drivers/media/tuners/qm1d1b0004.c:62:39: warning: 'default_cfg' defined but not used [-Wunused-const-variable=] static const struct qm1d1b0004_config default_cfg = { ^~~~~~~~~~~ This var is currently unused. So, comment it out. Signed-off-by:
-
- 09 May, 2018 11 commits
-
-
Sakari Ailus authored
The isp stat driver allocates memory for DMA and uses GFP_DMA flag for dev_alloc_coherent. The flag is no longer needed as the DMA mask is used for the purpose. Remove it. Reported-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
-
Sakari Ailus authored
The omap3isp driver checked whether the second argument (the new configuration) to the ISP statistics is NULL. This is the pointer to the user-given argument and is never NULL. Remove the check. Reported-by:
"Gustavo A. R. Silva" <gustavo@embeddedor.com> Suggested-by:
-
Arnd Bergmann authored
C libraries with 64-bit time_t use an incompatible format for struct omap3isp_stat_data. This changes the kernel code to support either version, by moving over the normal handling to the 64-bit variant, and adding compatiblity code to handle the old binary format with the existing ioctl command code. Fortunately, the command code includes the size of the structure, so the difference gets handled automatically. In the process of eliminating the references to 'struct timeval' from the kernel, I also change the way the timestamp is generated internally, basically by open-coding the v4l2_get_timestamp() call. [Sakari Ailus: Alphabetical order of headers, clean up compat code] Cc: Sakari Ailus <sakari.ailus@iki.fi> Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Reviewed-by:
-
Sami Tolvanen authored
This change fixes function types for media device ioctls to avoid indirect call mismatches with Control-Flow Integrity checking. Signed-off-by:
-
Jan Luebbe authored
A burst_size of 4 does not work for the 16 bit passthrough formats, so we use 8 instead. Signed-off-by:
Jan Luebbe <jlu@pengutronix.de> Acked-by:
Philipp Zabel <p.zabel@pengutronix.de> Acked-by:
Steve Longerbeam <steve_longerbeam@mentor.com> Signed-off-by:
-
Philipp Zabel authored
Since commit 50b0f0ae ("gpu: ipu-csi: add 10/12-bit grayscale support to mbus_code_to_bus_cfg") the IPU CSI can be configured to capture 10-bit and 12-bit grayscale formats, expanded to 16-bit grayscale, in bayer/generic data mode. This patch adds support for V4L2_PIX_FMT_Y16 captured from sensors that provide MEDIA_BUS_FMT_Y10_1X10 or MEDIA_BUS_FMT_Y12_1X12 data. Cc: Jan Luebbe <jlu@pengutronix.de> Signed-off-by:
-
Jasmin Jessich authored
This reverts 8b0e1953, because media-tree drivers should use the API functions to initialize variables of type ktime_t. Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
Jasmin Jessich <jasmin@anw.at> Signed-off-by:
-
Jasmin Jessich authored
In commit 20a63349 a new variable ktime_t delay has been added. We decided to use the API functions to initialize ktime_t variables within media-tree. Thus variable delay needs to be initialized with ktime_set() instead of setting it directly. Signed-off-by:
-
Julia Lawall authored
pvrusb2-video-v4l.h only declares pvr2_saa7115_subdev_update and includes pvrusb2-hdw-internal.h. pvrusb2-cx2584x-v4l.c does not use pvr2_saa7115_subdev_update and it explicitly includes pvrusb2-hdw-internal.h. Signed-off-by:
-
Brad Love authored
This issue was reported by a user who downloaded a corrupt saa7164 firmware, then went looking for a valid xc5000 firmware to fix the error displayed...but the device in question has no xc5000, thus after much effort, the wild goose chase eventually led to a support call. The xc5000 has nothing to do with saa7164 (as far as I can tell), so replace the string with saa7164 as well as give a meaningful hint on the firmware mismatch. Signed-off-by:
-
Jacopo Mondi authored
The renesas-ceu driver intializes the desired mbus_format at 'complete' time, inspecting the supported subdevice ones, and tuning some parameters to produce the requested memory format from what the sensor can produce. Although, the initially selected mbus_format was not provided to the subdevice during set_fmt and try_fmt operations, providing instead a '0' mbus format code. As long as the sensor defaults to a compatible mbus_format when an invalid code as '0' is provided, capture operations work correctly. If the subdevice defaults to an unsupported format (eg. some RGB permutations) capture does not work properly due to a mismatch on the expected and received image format on the wire. Fix that by re-using the initially selected mbus_format code during set_fmt and try_fmt subdevice operation calls. Tested by printing out the format selection procedure with ov7670 sensor. Before this patch: [ 0.866001] ov7670_try_fmt_internal -- Looking for mbus_code 0x0000 [ 0.870882] ov7670_try_fmt_internal -- Try mbus_code 0x2008 [ 0.876336] ov7670_try_fmt_internal -- Try mbus_code 0x1002 [ 0.881387] ov7670_try_fmt_internal -- Try mbus_code 0x1008 [ 0.886537] ov7670_try_fmt_internal -- Try mbus_code 0x3001 [ 0.891584] ov7670_try_fmt_internal -- mbus_code defaulted to 0x2008 With this patch applied: [ 0.867015] ov7670_try_fmt_internal -- Looking for mbus_code 0x2008 [ 0.873205] ov7670_try_fmt_internal -- Try mbus_code 0x2008: match Signed-off-by:
-
