- 04 Oct, 2019 25 commits
-
-
Jan Schmidt authored
If an endpoint is encountered that returns USB3_LPM_DEVICE_INITIATED, keep checking further endpoints, as there might be periodic endpoints later that return USB3_LPM_DISABLED due to shorter service intervals. Without this, the code can set too high a maximum-exit-latency and prevent the use of multiple USB3 cameras that should be able to work. Cc: <stable@vger.kernel.org> Signed-off-by: Jan Schmidt <jan@centricular.com> Tested-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/1570190373-30684-4-git-send-email-mathias.nyman@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Mathias Nyman authored
If host/hub initiated link pm is prevented by a driver flag we still must ensure that periodic endpoints have longer service intervals than link pm exit latency before allowing device initiated link pm. Fix this by continue walking and checking endpoint service interval if xhci_get_timeout_no_hub_lpm() returns anything else than USB3_LPM_DISABLED While at it fix the split line error message Tested-by: Jan Schmidt <jan@centricular.com> Cc: <stable@vger.kernel.org> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/1570190373-30684-3-git-send-email-mathias.nyman@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Mathias Nyman authored
The check printing out the "WARN Wrong bounce buffer write length:" uses incorrect values when comparing bytes written from scatterlist to bounce buffer. Actual copied lengths are fine. The used seg->bounce_len will be set to equal new_buf_len a few lines later in the code, but is incorrect when doing the comparison. The patch which added this false warning was backported to 4.8+ kernels so this should be backported as far as well. Cc: <stable@vger.kernel.org> # v4.8+ Fixes: 597c56e3 ("xhci: update bounce buffer with correct sg num") Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/1570190373-30684-2-git-send-email-mathias.nyman@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Johan Hovold authored
The driver would return with a nonzero open count in case the reset control request failed. This would prevent any further attempts to open the char dev until the device was disconnected. Fix this by incrementing the open count only on successful open. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by: Johan Hovold <johan@kernel.org> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20190919083039.30898-5-johan@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Johan Hovold authored
The driver is using its struct usb_device pointer as an inverted disconnected flag, but was setting it to NULL before making sure all completion handlers had run. This could lead to a NULL-pointer dereference in a number of dev_dbg and dev_err statements in the completion handlers which relies on said pointer. Fix this by unconditionally stopping all I/O and preventing resubmissions by poisoning the interrupt URBs at disconnect and using a dedicated disconnected flag. This also makes sure that all I/O has completed by the time the disconnect callback returns. Fixes: 9d974b2a ("USB: legousbtower.c: remove err() usage") Fixes: fef526ca ("USB: legousbtower: remove custom debug macro") Fixes: 4dae9963 ("USB: legotower: remove custom debug macro and module parameter") Cc: stable <stable@vger.kernel.org> # 3.5 Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20190919083039.30898-4-johan@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Johan Hovold authored
Fix a potential deadlock if disconnect races with open. Since commit d4ead16f ("USB: prevent char device open/deregister race") core holds an rw-semaphore while open is called and when releasing the minor number during deregistration. This can lead to an ABBA deadlock if a driver takes a lock in open which it also holds during deregistration. This effectively reverts commit 78663ecc ("USB: disconnect open race in legousbtower") which needlessly introduced this issue after a generic fix for this race had been added to core by commit d4ead16f ("USB: prevent char device open/deregister race"). Fixes: 78663ecc ("USB: disconnect open race in legousbtower") Cc: stable <stable@vger.kernel.org> # 2.6.24 Reported-by: syzbot+f9549f5ee8a5416f0b95@syzkaller.appspotmail.com Tested-by: syzbot+f9549f5ee8a5416f0b95@syzkaller.appspotmail.com Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20190919083039.30898-3-johan@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Johan Hovold authored
Make sure to check for short transfers when retrieving the version information at probe to avoid leaking uninitialised slab data when logging it. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Cc: stable <stable@vger.kernel.org> Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20190919083039.30898-2-johan@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Heikki Krogerus authored
Making sure that ucsi_displayport_enter() function does not return an error if the displayport alternate mode has already been entered. It's normal that the firmware (or controller) has already entered the alternate mode by the time the operating system is notified about the device. Fixes: af8622f6 ("usb: typec: ucsi: Support for DisplayPort alt mode") Cc: stable@vger.kernel.org Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Link: https://lore.kernel.org/r/20191004100219.71152-3-heikki.krogerus@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Heikki Krogerus authored
The "run_isr" flag is used for preventing the driver from calling the interrupt service routine in its runtime resume callback when the driver is expecting completion to a command, but what that basically does is that it hides the real problem. The real problem is that the controller is allowed to suspend in the middle of command execution. As a more appropriate fix for the problem, using autosuspend delay time that matches UCSI_TIMEOUT_MS (5s). That prevents the controller from suspending while still in the middle of executing a command. This fixes a potential deadlock. Both ccg_read() and ccg_write() are called with the mutex already taken at least from ccg_send_command(). In ccg_read() and ccg_write, the mutex is only acquired so that run_isr flag can be set. Fixes: f0e4cd94 ("usb: typec: ucsi: ccg: add runtime pm workaround") Cc: stable@vger.kernel.org Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Link: https://lore.kernel.org/r/20191004100219.71152-2-heikki.krogerus@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Johan Hovold authored
Replace the one remaining printk with pr_err(). Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20190926091228.24634-10-johan@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Johan Hovold authored
Drop the redundant lcd mutex introduced by commit 925ce689 ("USB: autoconvert trivial BKL users to private mutex") which replaced an earlier BKL use. The lock serialised calls to open() against other open() and a custom ioctl() returning the bcdDevice (sic!), but neither is needed. Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20190926091228.24634-9-johan@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Johan Hovold authored
Drop the redundant disconnect mutex which was introduced after the open-disconnect race had been addressed generally in USB core by commit d4ead16f ("USB: prevent char device open/deregister race"). Specifically, the rw-semaphore in core guarantees that all calls to open() will have completed and that no new calls to open() will occur after usb_deregister_dev() returns. Hence there is no need use the driver data as an inverted disconnected flag. Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20190926091228.24634-8-johan@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Johan Hovold authored
Make sure to stop all I/O on disconnect by adding a disconnected flag which is used to prevent new I/O from being started and by stopping all ongoing I/O before returning. This also fixes a potential use-after-free on driver unbind in case the driver data is freed before the completion handler has run. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Cc: stable <stable@vger.kernel.org> # 7bbe990cSigned-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20190926091228.24634-7-johan@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Mauro Carvalho Chehab authored
Those files got renamed, but another DT file still points to the older places. Fixes: 87a55485 ("dt-bindings: phy: meson-g12a-usb3-pcie-phy: convert to yaml") Fixes: da86d286 ("dt-bindings: phy: meson-g12a-usb2-phy: convert to yaml") Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Acked-by: Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/9ca2d136a1f79c878fff1208f9b536b0b613c0d5.1569330078.git.mchehab+samsung@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Dan Carpenter authored
The "port->typec_caps.data" and "port->typec_caps.type" variables are enums and in this context GCC will treat them as an unsigned int so they can never be less than zero. Fixes: ae8a2ca8 ("usb: typec: Group all TCPCI/TCPM code together") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Cc: stable <stable@vger.kernel.org> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Link: https://lore.kernel.org/r/20191001120117.GA23528@mwandaSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Jacky.Cao@sony.com authored
The power budget for SuperSpeed mode should be 900 mA according to USB specification, so set the power budget to 900mA for dummy_start_ss which is only used for SuperSpeed mode. If the max power consumption of SuperSpeed device is larger than 500 mA, insufficient available bus power error happens in usb_choose_configuration function when the device connects to dummy hcd. Signed-off-by: Jacky Cao <Jacky.Cao@sony.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/16EA1F625E922C43B00B9D82250220500871CDE5@APYOKXMS108.ap.sony.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Mao Wenan authored
If the return value of vhci_init_attr_group and sysfs_create_group is non-zero, which mean they failed to init attr_group and create sysfs group, so it would better add 'failed' message to indicate that. This patch also change pr_err to dev_err to trace which device is failed. Fixes: 0775a9cb ("usbip: vhci extension: modifications to vhci driver") Signed-off-by: Mao Wenan <maowenan@huawei.com> Acked-by: Shuah Khan <skhan@linuxfoundation.org> Link: https://lore.kernel.org/r/20190916150921.152977-1-maowenan@huawei.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Alan Stern authored
According to Greg KH, it has been generally agreed that when a USB driver encounters an unknown error (or one it can't handle directly), it should just give up instead of going into a potentially infinite retry loop. The three codes -EPROTO, -EILSEQ, and -ETIME fall into this category. They can be caused by bus errors such as packet loss or corruption, attempting to communicate with a disconnected device, or by malicious firmware. Nowadays the extent of packet loss or corruption is negligible, so it should be safe for a driver to give up whenever one of these errors occurs. Although the yurex driver handles -EILSEQ errors in this way, it doesn't do the same for -EPROTO (as discovered by the syzbot fuzzer) or other unrecognized errors. This patch adjusts the driver so that it doesn't log an error message for -EPROTO or -ETIME, and it doesn't retry after any errors. Reported-and-tested-by: syzbot+b24d736f18a1541ad550@syzkaller.appspotmail.com Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: Tomoki Sekiyama <tomoki.sekiyama@gmail.com> CC: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.1909171245410.1590-100000@iolanthe.rowland.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Johan Hovold authored
The driver was using its struct usb_device pointer as an inverted disconnected flag, but was setting it to NULL before making sure all completion handlers had run. This could lead to a NULL-pointer dereference in a number of dev_dbg statements in the completion handlers which relies on said pointer. The pointer was also dereferenced unconditionally in a dev_dbg statement release() something which would lead to a NULL-deref whenever a device was disconnected before the final character-device close if debugging was enabled. Fix this by unconditionally stopping all I/O and preventing resubmissions by poisoning the interrupt URBs at disconnect and using a dedicated disconnected flag. This also makes sure that all I/O has completed by the time the disconnect callback returns. Fixes: 1ef37c60 ("USB: adutux: remove custom debug macro and module parameter") Fixes: 66d4bc30 ("USB: adutux: remove custom debug macro") Cc: stable <stable@vger.kernel.org> # 3.12 Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20190925092913.8608-2-johan@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Johan Hovold authored
The driver was clearing its struct usb_device pointer, which it used as an inverted disconnected flag, before deregistering the character device and without serialising against racing release(). This could lead to a use-after-free if a racing release() callback observes the cleared pointer and frees the driver data before disconnect() is finished with it. This could also lead to NULL-pointer dereferences in a racing open(). Fixes: f08812d5 ("USB: FIx locks and urb->status in adutux (updated)") Cc: stable <stable@vger.kernel.org> # 2.6.24 Reported-by: syzbot+0243cb250a51eeefb8cc@syzkaller.appspotmail.com Tested-by: syzbot+0243cb250a51eeefb8cc@syzkaller.appspotmail.com Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20190925092913.8608-1-johan@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Pawel Laszczak authored
Patch fix issue in cdns3_ep0_feature_handle_device function. The function usleep_range can't be used there because this function is called with locks held and IRQs disabled in cdns3_device_thread_irq_handler(). To resolve this issue patch replaces usleep_range with mdelay. Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Pawel Laszczak <pawell@cadence.com> Fixes: 7733f6c3 ("usb: cdns3: Add Cadence USB3 DRD Driver") Reviewed-by: Peter Chen <peter.chen@nxp.com> Link: https://lore.kernel.org/r/1569484721-4424-1-git-send-email-pawell@cadence.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Dan Carpenter authored
We can't use "wrap" after it has been freed. Fixes: 7733f6c3 ("usb: cdns3: Add Cadence USB3 DRD Driver") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Link: https://lore.kernel.org/r/20190904100102.GB7007@mwandaSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Johan Hovold authored
Add missing bulk-in endpoint sanity check to prevent uninitialised stack data from being reported to the system log and used as endpoint addresses. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Cc: stable <stable@vger.kernel.org> Reported-by: syzbot+5630ca7c3b2be5c9da5e@syzkaller.appspotmail.com Signed-off-by: Johan Hovold <johan@kernel.org> Acked-by: Oliver Neukum <oneukum@suse.com> Link: https://lore.kernel.org/r/20191003070931.17009-1-johan@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Jonathan Neuschäfer authored
usb-hcd.txt has been converted to YAML. Update references accordingly. Fixes: 14ec072a ("dt-bindings: usb: Convert USB HCD generic binding to YAML") Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net> Link: https://lore.kernel.org/r/20191003193132.17758-1-j.neuschaefer@gmx.netSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Bastien Nocera authored
The Rio500 kernel driver has not been used by Rio500 owners since 2001 not long after the rio500 project added support for a user-space USB stack through the very first versions of usbdevfs and then libusb. Support for the kernel driver was removed from the upstream utilities in 2008: https://gitlab.freedesktop.org/hadess/rio500/commit/943f624ab721eb8281c287650fcc9e2026f6f5db Cc: Cesar Miquel <miquel@df.uba.ar> Signed-off-by: Bastien Nocera <hadess@hadess.net> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/6251c17584d220472ce882a3d9c199c401a51a71.camel@hadess.netSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 30 Sep, 2019 15 commits
-
-
Linus Torvalds authored
-
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linuxLinus Torvalds authored
Pull btrfs fixes from David Sterba: "A bunch of fixes that accumulated in recent weeks, mostly material for stable. Summary: - fix for regression from 5.3 that prevents to use balance convert with single profile - qgroup fixes: rescan race, accounting leak with multiple writers, potential leak after io failure recovery - fix for use after free in relocation (reported by KASAN) - other error handling fixups" * tag 'for-5.4-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux: btrfs: qgroup: Fix reserved data space leak if we have multiple reserve calls btrfs: qgroup: Fix the wrong target io_tree when freeing reserved data space btrfs: Fix a regression which we can't convert to SINGLE profile btrfs: relocation: fix use-after-free on dead relocation roots Btrfs: fix race setting up and completing qgroup rescan workers Btrfs: fix missing error return if writeback for extent buffer never started btrfs: adjust dirty_metadata_bytes after writeback failure of extent buffer Btrfs: fix selftests failure due to uninitialized i_mode in test inodes
-
git://github.com/c-sky/csky-linuxLinus Torvalds authored
Pull csky updates from Guo Ren: "This round of csky subsystem just some fixups: - Fix mb() synchronization problem - Fix dma_alloc_coherent with PAGE_SO attribute - Fix cache_op failed when cross memory ZONEs - Optimize arch_sync_dma_for_cpu/device with dma_inv_range - Fix ioremap function losing - Fix arch_get_unmapped_area() implementation - Fix defer cache flush for 610 - Support kernel non-aligned access - Fix 610 vipt cache flush mechanism - Fix add zero_fp fixup perf backtrace panic - Move static keyword to the front of declaration - Fix csky_pmu.max_period assignment - Use generic free_initrd_mem() - entry: Remove unneeded need_resched() loop" * tag 'csky-for-linus-5.4-rc1' of git://github.com/c-sky/csky-linux: csky: Move static keyword to the front of declaration csky: entry: Remove unneeded need_resched() loop csky: Fixup csky_pmu.max_period assignment csky: Fixup add zero_fp fixup perf backtrace panic csky: Use generic free_initrd_mem() csky: Fixup 610 vipt cache flush mechanism csky: Support kernel non-aligned access csky: Fixup defer cache flush for 610 csky: Fixup arch_get_unmapped_area() implementation csky: Fixup ioremap function losing csky: Optimize arch_sync_dma_for_cpu/device with dma_inv_range csky/dma: Fixup cache_op failed when cross memory ZONEs csky: Fixup dma_alloc_coherent with PAGE_SO attribute csky: Fixup mb() synchronization problem
-
git://git.kernel.org/pub/scm/linux/kernel/git/soc/socLinus Torvalds authored
Pull ARM SoC fixes from Olof Johansson: "A few fixes that have trickled in through the merge window: - Video fixes for OMAP due to panel-dpi driver removal - Clock fixes for OMAP that broke no-idle quirks + nfsroot on DRA7 - Fixing arch version on ASpeed ast2500 - Two fixes for reset handling on ARM SCMI" * tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: ARM: aspeed: ast2500 is ARMv6K reset: reset-scmi: add missing handle initialisation firmware: arm_scmi: reset: fix reset_state assignment in scmi_domain_reset bus: ti-sysc: Remove unpaired sysc_clkdm_deny_idle() ARM: dts: logicpd-som-lv: Fix i2c2 and i2c3 Pin mux ARM: dts: am3517-evm: Fix missing video ARM: dts: logicpd-torpedo-baseboard: Fix missing video ARM: omap2plus_defconfig: Fix missing video bus: ti-sysc: Fix handling of invalid clocks bus: ti-sysc: Fix clock handling for no-idle quirks
-
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-traceLinus Torvalds authored
Pull tracing fixes from Steven Rostedt: "A few more tracing fixes: - Fix a buffer overflow by checking nr_args correctly in probes - Fix a warning that is reported by clang - Fix a possible memory leak in error path of filter processing - Fix the selftest that checks for failures, but wasn't failing - Minor clean up on call site output of a memory trace event" * tag 'trace-v5.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: selftests/ftrace: Fix same probe error test mm, tracing: Print symbol name for call_site in trace events tracing: Have error path in predicate_parse() free its allocated memory tracing: Fix clang -Wint-in-bool-context warnings in IF_ASSIGN macro tracing/probe: Fix to check the difference of nr_args before adding probe
-
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmcLinus Torvalds authored
Pull more MMC updates from Ulf Hansson: "A couple more updates/fixes for MMC: - sdhci-pci: Add Genesys Logic GL975x support - sdhci-tegra: Recover loss in throughput for DMA - sdhci-of-esdhc: Fix DMA bug" * tag 'mmc-v5.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: mmc: host: sdhci-pci: Add Genesys Logic GL975x support mmc: tegra: Implement ->set_dma_mask() mmc: sdhci: Let drivers define their DMA mask mmc: sdhci-of-esdhc: set DMA snooping based on DMA coherence mmc: sdhci: improve ADMA error reporting
-
Krzysztof Wilczynski authored
Move the static keyword to the front of declaration of csky_pmu_of_device_ids, and resolve the following compiler warning that can be seen when building with warnings enabled (W=1): arch/csky/kernel/perf_event.c:1340:1: warning: ‘static’ is not at beginning of declaration [-Wold-style-declaration] Signed-off-by: Krzysztof Wilczynski <kw@linux.com> Signed-off-by: Guo Ren <guoren@kernel.org>
-
Valentin Schneider authored
Since the enabling and disabling of IRQs within preempt_schedule_irq() is contained in a need_resched() loop, we don't need the outer arch code loop. Signed-off-by: Valentin Schneider <valentin.schneider@arm.com> Signed-off-by: Guo Ren <guoren@kernel.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-miscLinus Torvalds authored
Pull Documentation/process update from Greg KH: "Here are two small Documentation/process/embargoed-hardware-issues.rst file updates that missed my previous char/misc pull request. The first one adds an Intel representative for the process, and the second one cleans up the text a bit more when it comes to how the disclosure rules work, as it was a bit confusing to some companies" * tag 'char-misc-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: Documentation/process: Clarify disclosure rules Documentation/process: Volunteer as the ambassador for Intel
-
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfsLinus Torvalds authored
Pull more vfs updates from Al Viro: "A couple of misc patches" * 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: afs dynroot: switch to simple_dir_operations fs/handle.c - fix up kerneldoc
-
git://git.samba.org/sfrench/cifs-2.6Linus Torvalds authored
Pull more cifs updates from Steve French: "Fixes from the recent SMB3 Test events and Storage Developer Conference (held the last two weeks). Here are nine smb3 patches including an important patch for debugging traces with wireshark, with three patches marked for stable. Additional fixes from last week to better handle some newly discovered reparse points, and a fix the create/mkdir path for setting the mode more atomically (in SMB3 Create security descriptor context), and one for path name processing are still being tested so are not included here" * tag '5.4-rc-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6: CIFS: Fix oplock handling for SMB 2.1+ protocols smb3: missing ACL related flags smb3: pass mode bits into create calls smb3: Add missing reparse tags CIFS: fix max ea value size fs/cifs/sess.c: Remove set but not used variable 'capabilities' fs/cifs/smb2pdu.c: Make SMB2_notify_init static smb3: fix leak in "open on server" perf counter smb3: allow decryption keys to be dumped by admin for debugging
-
Mao Han authored
The csky_pmu.max_period has type u64, and BIT() can only return 32 bits unsigned long on C-SKY. The initialization for max_period will be incorrect when count_width is bigger than 32. Use BIT_ULL() Signed-off-by: Mao Han <han_mao@c-sky.com> Signed-off-by: Guo Ren <ren_guo@c-sky.com>
-
Guo Ren authored
We need set fp zero to let backtrace know the end. The patch fixup perf callchain panic problem, because backtrace didn't know what is the end of fp. Signed-off-by: Guo Ren <ren_guo@c-sky.com> Reported-by: Mao Han <han_mao@c-sky.com>
-
Mike Rapoport authored
The csky implementation of free_initrd_mem() is an open-coded version of free_reserved_area() without poisoning. Remove it and make csky use the generic version of free_initrd_mem(). Signed-off-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Guo Ren <guoren@kernel.org>
-
Linus Torvalds authored
Merge active entropy generation updates. This is admittedly partly "for discussion". We need to have a way forward for the boot time deadlocks where user space ends up waiting for more entropy, but no entropy is forthcoming because the system is entirely idle just waiting for something to happen. While this was triggered by what is arguably a user space bug with GDM/gnome-session asking for secure randomness during early boot, when they didn't even need any such truly secure thing, the issue ends up being that our "getrandom()" interface is prone to that kind of confusion, because people don't think very hard about whether they want to block for sufficient amounts of entropy. The approach here-in is to decide to not just passively wait for entropy to happen, but to start actively collecting it if it is missing. This is not necessarily always possible, but if the architecture has a CPU cycle counter, there is a fair amount of noise in the exact timings of reasonably complex loads. We may end up tweaking the load and the entropy estimates, but this should be at least a reasonable starting point. As part of this, we also revert the revert of the ext4 IO pattern improvement that ended up triggering the reported lack of external entropy. * getrandom() active entropy waiting: Revert "Revert "ext4: make __ext4_get_inode_loc plug"" random: try to actively add entropy rather than passively wait for it
-