This patch removes the redundant lan_id in the phy struct and uses
the bus version.  Both variables exist and intend to represent the
STATUS register LAN_ID field.  However, phy.lan_id is not bit shifted
so the phy.lan_id = 0x0 for LAN Id 0 and phy.lan_id = 0x4 for LAN Id 1.
Where bus.lan_id is bit shifted so bus.lan_id = 0x0 for LAN Id 0 and
bus.lan_id = 0x1 for LAN Id 1. There seems no need for the additional
lan_id variable and this should make the code less confusing.
Signed-off-by: Donald C Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Use kzalloc rather than kcalloc(1..

The semantic patch that makes this change is as follows:

// <smpl>
@@
@@

- kcalloc(1,
+ kzalloc(
          ...)
// </smpl>

and removing checkpatch below CHECK:
CHECK: Prefer kzalloc(sizeof(*fwd_adapter)...) over
kzalloc(sizeof(struct ixgbe_fwd_adapter)...)
Signed-off-by: Maninder Singh <maninder1.s@samsung.com>
Reviewed-by: Vaneet Narang <v.narang@samsung.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The ixgbe never has as very doubtfully ever will support either
PCI or PCI-X devices.  So remove the unused types from the
ixgbe_bus_type.  Thanks to Alex Duyck for suggesting this.
Signed-off-by: Donald C Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

With this patch we add support for a new bus type ixgbe_bus_type_internal.
X550em devices use IOSF and not PCIe bus so this new type is to accommodate
them.
Signed-off-by: Donald C Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Added ixgbe_get_bus_info_X550em to X550 code. ixgbe_get_bus_info_X550em
sets bus.width to ixgbe_bus_width_unknown and bus.speed to
ixgbe_bus_speed_unknown, because IOSF does not report a PCIe bus
width or speed.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

When the device is closing or suspending, call ixgbe_enter_lplu to
enter low power link up state on devices that support it. When this
is done, prevent the phy from being reset in the ixgbe_down path
so that link is present when calling ixgbe_enter_lplu.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Add support for VXLAN RX offloads for the X55x devices that support
them.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

By using GSO for UDP-encapsulated packets, all ixgbe devices can
be directed to generate checksums for the inner headers because
the outer UDP checksum can be zero. So point the machinery at the
inner headers and have the hardware generate the checksum.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Wait up to about 100 us for FDIRCMD writes to complete and return
failure indications.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

There are various reasons why this method may or may not need to be
defined and some of these we don't know until runtime.  So we will
set the value in get_invariants.
Signed-off-by: Donald C Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds a support function that will indicate for the
existence of management FW.
Signed-off-by: Donald C Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This fixes bugs where the port is not receiving multicast or VLAN tagged
packets when in promiscuous mode. This can occur when a SW bridge is
created on top of the device.

This also fixes issues where the promiscuous behavior setting was not
being preserved across a reset caused by features being enabled or
disabled.

We are using defport instead of doing a true promiscuous mode because we do
not need to receive the SRIOV or VMDq VSI directed traffic which would suck
up bandwidth and is really not intended for the SW bridge.

In addition, with defport we get VLAN promiscuous behavior which is not
possible from the VSI level promiscuous setting.

Change-ID: Ie21985eac32d5af1c02e9d71c6430a90d5bab40f
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

opts_size is only written and never read. Following patch
removes this unused variable.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Marius Tomaschewski <mt@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

As David pointed out, spinlock are no longer needed
to protect the per cpu queues used in gro cells infrastructure.

Also use new napi_complete_done() API so that gro_flush_timeout
tweaks have an effect.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Other Sierra Wireless MC73xx devices exist, with different USB IDs.

Cc: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David Ward <david.ward@ll.mit.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>

The kernel is applying the RA managed/otherconf flags silently and
forgets to send ifinfo notify to inform about their change when the
router provides a zero reachable_time and retrans_timer as dnsmasq
and many routers send it, which just means unspecified by this router
and the host should continue using whatever value it is already using.
Userspace may monitor the ifinfo notifications to activate dhcpv6.
Signed-off-by: Marius Tomaschewski <mt@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Andrew Lunn says:

====================
DSA port configuration and status

This patchset allows various switch port settings to be configured and
port status to be sampled. Some of these patches have been posted
before.

The first three patches provide infrastructure for configuring a
switch ports link speed and duplex from a fixed_link phy.

Patch four then uses this infrastructure to allow the CPU and DSA
ports of a switch to be configured using a fixed-link property in the
device tree.

Patches five and six allow a phy-mode property to be specified in the
device tree, and allow this to be used for configuring RGMII delays.

Patches seven through nine allow link status, for example that of an
SFP module, to be read from a gpio.

Changes since v1:

Rewrite 9/9 so that it hopefully does not regression on
868a4215 ("net: phy: fixed_phy: handle link-down case")
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

What features a phy supports is masked in genphy_config_init() by
looking at the PHYs BMSR register.

If the link is down, fixed_phy_update_regs() will only set the auto-
negotiation capable bit in BMSR. Thus genphy_config_init() comes to
the conclusion the PHY can only perform 10/Half, and masks out the
higher speed features. If however the link it up, BMSR is set to
indicate the speed the PHY is capable of auto-negotiating, and
genphy_config_init() does not mask out the high speed features.

To fix this, when the link is down, have fixed_phy_update_regs() leave
the link status, auto-negotiation complete, and link partner
capabilities unset, but set all the local capabilities depending on
the fixed phy speed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

An SFP module may have a link up/down status pin which can be
connection to a GPIO line of the host. Add support for reading such an
GPIO in the fixed_phy driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When polling for link status, don't consider ports which have a forced
link. Such ports don't monitor their phy or may not even have a phy.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some Marvell switches allow the RGMII Rx and Tx clock to be delayed
when the port is using RGMII. Have the adjust_link function look at
the phy interface type and enable this delay as requested.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It can be useful for DSA and CPU ports to have a phy-mode property, in
particular to specify RGMII delays. Parse the property and set it in
the fixed-link phydev.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

By default, DSA and CPU ports are configured to the maximum speed the
switch supports. However there can be use cases where the peer devices
port is slower. Allow a fixed-link property to be used with the DSA
and CPU port in the device tree, and use this information to configure
the port.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Set the supported field of the phydev to indicate the speed features
of the phy. If the phy is never attached to a netdev, but used in an
adjust_link() function, the speed will be incorrectly evaluated to
10/half rather than the correct speed/duplex.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current code sets user ports to perform auto negotiation using the
phy. CPU and DSA ports are configured to full duplex and maximum speed
the switch supports.

There are however use cases where the CPU has a slower port, and when
user ports have SFP modules with fixed speed. In these cases, port
settings to be read from a fixed_phy devices. The switch driver then
needs to implement the adjust_link op, so the port settings can be
set.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some Ethernet MAC drivers using the PHY library require the hardcoding
of link parameters when interfaced to a switch device, SFP module,
switch to switch port, etc. This has typically lead to various ad-hoc
implementations looking like this:

- using a "fixed PHY" emulated device, which will provide link
  indication towards the Ethernet MAC driver and hardware

- pretend there is no PHY and hardcode link parameters, ala mv643x_eth

Based on that, it is desireable to have the PHY drivers advertise the
correct link parameters, just like regular Ethernet PHYs towards their
CPU Ethernet MAC drivers, however, Ethernet MAC drivers should be able
to tell whether this link should be monitored or not. In the context
of an Ethernet switch, SFP module, switch to switch link, we do not
need to monitor this link since it should be always up.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix a memory leak in the mpls netns init function in case of failure. If
register_net_sysctl fails then we need to free the ctl_table.

Fixes: 7720c01f ("mpls: Add a sysctl to control the size of the mpls label table")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

TOS is another key aspect of the lookup passed to fib_validate_source.
Add it to the tracepoint.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To fix build errors:
kernel/built-in.o: In function `bpf_trace_printk':
bpf_trace.c:(.text+0x11a254): undefined reference to `strncpy_from_unsafe'
kernel/built-in.o: In function `fetch_memory_string':
trace_kprobe.c:(.text+0x11acf8): undefined reference to `strncpy_from_unsafe'

move strncpy_from_unsafe() next to probe_kernel_read/write()
which use the same memory access style.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Fixes: 1a6877b9 ("lib: introduce strncpy_from_unsafe()")
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Daniel Borkmann says:

====================
tcp: receive-side per route dctcp handling

Original cover letter:

  Currently, the following case doesn't use DCTCP, even if it should:

    - responder has f.e. cubic as system wide default
    - 'ip route congctl dctcp $src' was set

  Then, DCTCP is NOT used if a DCTCP sender attempts to connect from a
  host in the $src range: ECT(0) is set, but listen_sk is not dctcp, so
  we fail the INET_ECN_is_not_ect sanity check.

  We also have to examine the dst used for the SYN/ACK reply to make
  this case work.

  In order to minimize additional cost, store the 'ecn is must have'
  information is the dst_features field.

  The set targets -next instead of -net since this doesn't seem to be a
  serious bug and to give the change more soak time until it hits linus
  tree.

v1 -> v2:
 - Addressed Dave's feedback, not exposing any bits to user space
 - Added patch 3 to reject incorrect configurations
 - Rest as is, rebased and retested
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, the following case doesn't use DCTCP, even if it should:
A responder has f.e. Cubic as system wide default, but for a specific
route to the initiating host, DCTCP is being set in RTAX_CC_ALGO. The
initiating host then uses DCTCP as congestion control, but since the
initiator sets ECT(0), tcp_ecn_create_request() doesn't set ecn_ok,
and we have to fall back to Reno after 3WHS completes.

We were thinking on how to solve this in a minimal, non-intrusive
way without bloating tcp_ecn_create_request() needlessly: lets cache
the CA ecn option flag in RTAX_FEATURES. In other words, when ECT(0)
is set on the SYN packet, set ecn_ok=1 iff route RTAX_FEATURES
contains the unexposed (internal-only) DST_FEATURE_ECN_CA. This allows
to only do a single metric feature lookup inside tcp_ecn_create_request().

Joint work with Florian Westphal.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Feature bits that are invalid should not be accepted by the kernel,
only the lower 4 bits may be configured, but not the remaining ones.
Even from these 4, 2 of them are unused.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Reduce the identation a bit, there's no need to artificically have
it increased.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

fib_create_info() is already quite large, so before adding more
code to the metrics section move that to a helper, similar to
ip6_convert_metrics.
Suggested-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Document the addition of a new sysctl variable which controls the
generation of IGMP reports for link local multicast groups in the
224.0.0.X range.

IGMP reports for local multicast groups can now be optionally
inhibited by setting the value to zero e.g.:
echo 0 > /proc/sys/net/ipv4/igmp_link_local_mcast_reports

To retain backwards compatibility the previous behaviour is retained
by default on system boot or reverted by setting the value back to
non-zero.
Signed-off-by: Philip Downey <pdowney@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently tun-info options pointer is used in few cases to
pass options around. But tunnel options can be accessed using
ip_tunnel_info_opts() API without using the pointer. Following
patch removes the redundant pointer and consistently make use
of API.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Address remaining issue after 80ec1927.
Signed-off-by: Madalin Bucur <madalin.bucur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

   net/ipv4/af_inet.c: In function 'snmp_get_cpu_field64':
>> net/ipv4/af_inet.c:1486:26: error: 'offt' undeclared (first use in this function)
      v = *(((u64 *)bhptr) + offt);
                             ^
   net/ipv4/af_inet.c:1486:26: note: each undeclared identifier is reported only once for each function it appears in
   net/ipv4/af_inet.c: In function 'snmp_fold_field64':
>> net/ipv4/af_inet.c:1499:39: error: 'offct' undeclared (first use in this function)
      res += snmp_get_cpu_field(mib, cpu, offct, syncp_offset);
                                          ^
>> net/ipv4/af_inet.c:1499:10: error: too many arguments to function 'snmp_get_cpu_field'
      res += snmp_get_cpu_field(mib, cpu, offct, syncp_offset);
             ^
   net/ipv4/af_inet.c:1455:5: note: declared here
    u64 snmp_get_cpu_field(void __percpu *mib, int cpu, int offt)
        ^
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Poll() returns immediately after setting the kernel current frame
(ring->head) to SKIP from user space even though there is no new
frame. And in a case of all frames is VALID, user space program
unintensionally sets (only) kernel current frame to UNUSED, then
calls poll(), it will not return immediately even though there are
VALID frames.

To avoid situations like above, I think we need to scan all frames
to find VALID frames at poll() like netlink_alloc_skb(),
netlink_forward_ring() finding an UNUSED frame at skb allocation.
Signed-off-by: Ken-ichirou MATSUZAWA <chamas@h4.dion.ne.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>