Fix the name of the iio_device parameter for a few functions and add
documentation for one missing function parameter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

The adxrs450 requires a delay of at least 0.1 ms between register writes.  Using
msleep() for such small delays is not recommended. So use usleep_range instead.

Fixes the following checkpatch warning:
	WARNING: msleep < 20ms can sleep for up to 20ms; see Documentation/timers/timers-howto.txt
	+	msleep(1);
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

This is one of the exceptions to the 80 chars per line rule since breaking the
string in half it badly affects the grep-ability.

Fixes the following checkpatch warning:
	WARNING: quoted string split across lines
	#203: FILE: staging/iio/gyro/adxrs450_core.c:203:
		+		dev_warn(&st->us->dev, "The initial power on response "
		+			 "is not correct! Restart without reset?\n");
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Reflow two lines to meet the 80 characters per line limit.

Fixes the following checkpatch warnings:
	WARNING: line over 80 characters
	#29: FILE: staging/iio/gyro/adxrs450_core.c:29:
	+ * @reg_address: the address of the lower of the two registers,which should be an even address,

	WARNING: line over 80 characters
	#81: FILE: staging/iio/gyro/adxrs450_core.c:81:
	+ * @reg_address: the address of the lower of the two registers,which should be an even address,
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Don't spam the bootlog with the devices part id and serial number.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Instead of silently discarding the upper bits reject out of range values for the
calibscale property.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

The calibbias (DNC) register contains a 10-bit twos complement value. Perform a
proper sign extension when reading the register, otherwise negative will
incorrectly be displayed as large positive values.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Fixes the following sparse warnings:

	drivers/staging/iio/gyro/adxrs450_core.c:46:15: warning: cast to restricted __be32
	drivers/staging/iio/gyro/adxrs450_core.c:62:17: warning: cast to restricted __be32
	drivers/staging/iio/gyro/adxrs450_core.c:89:15: warning: cast to restricted __be32
	drivers/staging/iio/gyro/adxrs450_core.c:129:17: warning: cast to restricted __be32
	drivers/staging/iio/gyro/adxrs450_core.c:168:16: warning: cast to restricted __be32
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

This partially reverts commit cb449687. There is
no apparent reason why we should split a transaction which consists out of
multiple transfers into multiple transactions each having one transfer. While
this works it introduces a bunch of unnecessary context switch and additional
setup costs.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

__iio_update_buffer updates the buffer's bytes_per_datum and length fields.
But the only user of this function just passes in these exact fields, so the
call basically looks like this:

	buffer->bytes_per_datum = buffer->bytes_per_datum;
	buffer->length = buffer->length;

Which means it is a noop and can be removed. Also remove the function itself,
since it is now unused.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

This patch adds a generic magnetometer driver for STMicroelectronics
magnetometers, currently it supports:
LSM303DLHC, LSM303DLM, LIS3MDL.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

This patch adds a generic gyroscope driver for STMicroelectronics
gyroscopes, currently it supports:
L3G4200D, LSM330DL, L3GD20, L3GD20H, LSM330DLC, L3G4IS, LSM330.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

This patch adds a generic accelerometer driver for STMicroelectronics
accelerometers, currently it supports:
LSM303DLH, LSM303DLHC, LIS3DH, LSM330D, LSM330DL, LSM330DLC,
LIS331DLH, LSM303DL, LSM303DLM, LSM330.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

This patch add a generic library for STMicroelectronics 3-axis sensors.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

These functions are only used by the comedi core. Move the
prototypes to comedi_internal.h so they are not exposed to
the comedi drivers.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

These functions are only used by the comedi core. Move the
prototypes to comedi_internal.h so they are not exposed to
the comedi drivers.

Tidy up comedi_internal.h a bit so that all the internal stuff
in drivers.c is grouped.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Group all the general comedi driver register/config/attach
prototypes into one place in comedidev.h.

Reorder the functions in drivers.c a bit so they are in a more
logical usage order (bottom to top).
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Convert this pcmcia driver to the comedi auto attach mechanism.

This allows getting rid of the "hack" needed to pass the pcmcia_device
pointer from the pcmcia_driver to the comedi_driver.

We can also get rid of the boardinfo since it was only used to
provide the "name" that was used with the manual attach.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Convert this pcmcia driver to the comedi auto attach mechanism.

This allows getting rid of the "hack" needed to pass the pcmcia_device
pointer from the pcmcia_driver to the comedi_driver.

We still need the boardinfo because the das08 driver uses it. But we
can get rid of the duplicate that allowed attaching with the driver
name.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Convert this pcmcia driver to the comedi auto attach mechanism.

This allows getting rid of the "hack" needed to pass the pcmcia_device
pointer from the pcmcia_driver to the comedi_driver.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Introduce some helper functions to allow converting the comedi
pcmcia drivers to the comedi auto_attach mechanism.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Separate the comedi_pcmcia_* functions out of drivers.c into a new
source file, comedi_pcmcia.c. This allows conditionally building
support for comedi pcmcia drivers into the comedi core without the
need for the #if'defery. Fix the Kconfig and Makefile appropriately.

Group all the comedi_pcmcia_* prototypes into one place in comedidev.h.
Protect these prototypes with an #ifdef so that building a comedi
pcmcia driver without PCMCIA support will cause a build error. This
will normally not happen as long as the comedi pcmcia driver is placed
in the proper group in the Kconfig.

Remove the #include <pcmcia/*.h> from drivers.c. These includes are only
needed by the comedi pcmcia driver support code and the pcmcia drivers.
The include should occur in those files.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Separate the comedi_pci_* functions out of drivers.c into a new
source file, comedi_pci.c. This allows conditionally building
support for comedi PCI drivers into the comedi core. Fix the
Kconfig and Makefile appropriately.

Group all the comedi_pci_* prototypes and related defines into one
place in comedidev.h. Protect these prototypes with an #ifdef and
provide some dummy functions so that the mixed ISA/PCI comedi
drivers will still build correctly.

Remove the #include <linux/pci.h> from comedidev.h and drivers.c. This
include is only needed by the comedi PCI driver support code and the
PCI drivers. The include should occur in those files.

Also, remove the #include <linux/pci.h> from a couple non-PCI drivers
since it's not needed.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Separate the comedi_usb_* functions out of drivers.c into a new
source file, comedi_usb.c. This allows conditionally building
support for comedi USB drivers into the comedi core without the
need for the #if'defery. Fix the Kconfig and Makefile appropriately.
For aesthetic reasons, add some whitespace to the Makefile to keep
everything lined up.

Group all the comedi_usb_* prototypes into one place in comedidev.h.
Protect these prototypes with an #ifdef so that building a comedi
usb driver without USB support will cause a build error. This will
normally not happen as long as the comedi USB driver is placed in
the proper group in the Kconfig.

Remove the #include<linux/usb.h> from comedidev.h and drivers.c. This
include is only needed by the comedi USB driver support code and the
USB drivers. The include should occur in those files.

Removing the include of usb.h exposed a couple drivers that need
<linux/interrupt.h> and <linux/sched.h>. Add the missing includes.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This error happens because PIPEnsControlOut and PIPEnsControlIn unlock the
spin lock for delay, letting in another thread.

The patch moves the current MP_SET_FLAG to before filling
of sUsbCtlRequest for pControlURB and clears it in event of failing.

Any thread calling either function while fMP_CONTROL_READS or fMP_CONTROL_WRITES
flags set will return STATUS_FAILURE.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Cc: stable@vger.kernel.org # 3.8
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix:
drivers/staging/fwserial/fwserial.c:581:3: warning: format '%ld' expects argument of type 'long int', but argument 4 has type 'size_t'
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fixes these sparse warnings:
drivers/staging/fwserial/fwserial.c:430:16: sparse: incompatible types in comparison expression (different address spaces)
drivers/staging/fwserial/fwserial.c:699:30: sparse: incompatible types in comparison expression (different address spaces)
drivers/staging/fwserial/fwserial.c:802:16: sparse: incompatible types in comparison expression (different address spaces)
drivers/staging/fwserial/fwserial.c:898:16: sparse: incompatible types in comparison expression (different address spaces)
drivers/staging/fwserial/fwserial.c:1842:14: sparse: incompatible types in comparison expression (different address spaces)
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

zs_create_pool() currently takes a name argument which is
never used in any useful way.

This patch removes it.
Signed-off-by: Seth Jennings <sjenning@linux.vnet.ibm.com>
Acked-by: Nitin Gupta <ngupta@vflare.org>
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

m68k allmodconfig:

  CC [M]  drivers/staging/comedi/drivers/pcl812.o
drivers/staging/comedi/drivers/pcl812.c: In function ‘pcl812_ai_cmd’:
drivers/staging/comedi/drivers/pcl812.c:736: error: implicit declaration of function ‘set_dma_mode’
drivers/staging/comedi/drivers/pcl812.c:736: error: ‘DMA_MODE_READ’ undeclared (first use in this function)
drivers/staging/comedi/drivers/pcl812.c:736: error: (Each undeclared identifier is reported only once
drivers/staging/comedi/drivers/pcl812.c:736: error: for each function it appears in.)
drivers/staging/comedi/drivers/pcl812.c:737: error: implicit declaration of function ‘claim_dma_lock’
drivers/staging/comedi/drivers/pcl812.c:738: error: implicit declaration of function ‘clear_dma_ff’
drivers/staging/comedi/drivers/pcl812.c:739: error: implicit declaration of function ‘set_dma_addr’
drivers/staging/comedi/drivers/pcl812.c:740: error: implicit declaration of function ‘set_dma_count’
drivers/staging/comedi/drivers/pcl812.c:741: error: implicit declaration of function ‘release_dma_lock’
drivers/staging/comedi/drivers/pcl812.c:742: error: implicit declaration of function ‘enable_dma’
drivers/staging/comedi/drivers/pcl812.c: In function ‘interrupt_pcl812_ai_dma’:
drivers/staging/comedi/drivers/pcl812.c:883: error: implicit declaration of function ‘disable_dma’
drivers/staging/comedi/drivers/pcl812.c:884: error: ‘DMA_MODE_READ’ undeclared (first use in this function)
drivers/staging/comedi/drivers/pcl812.c: In function ‘pcl812_ai_poll’:
drivers/staging/comedi/drivers/pcl812.c:947: error: implicit declaration of function ‘get_dma_residue’
make[2]: *** [drivers/staging/comedi/drivers/pcl812.o] Error 1
  CC [M]  drivers/staging/comedi/drivers/pcl816.o
drivers/staging/comedi/drivers/pcl816.c: In function ‘interrupt_pcl816_ai_mode13_dma’:
drivers/staging/comedi/drivers/pcl816.c:359: error: implicit declaration of function ‘disable_dma’
drivers/staging/comedi/drivers/pcl816.c:366: error: implicit declaration of function ‘set_dma_mode’
drivers/staging/comedi/drivers/pcl816.c:366: error: ‘DMA_MODE_READ’ undeclared (first use in this function)
drivers/staging/comedi/drivers/pcl816.c:366: error: (Each undeclared identifier is reported only once
drivers/staging/comedi/drivers/pcl816.c:366: error: for each function it appears in.)
drivers/staging/comedi/drivers/pcl816.c:367: error: implicit declaration of function ‘claim_dma_lock’
drivers/staging/comedi/drivers/pcl816.c:369: error: implicit declaration of function ‘set_dma_addr’
drivers/staging/comedi/drivers/pcl816.c:372: error: implicit declaration of function ‘set_dma_count’
drivers/staging/comedi/drivers/pcl816.c:378: error: implicit declaration of function ‘release_dma_lock’
drivers/staging/comedi/drivers/pcl816.c:379: error: implicit declaration of function ‘enable_dma’
drivers/staging/comedi/drivers/pcl816.c: In function ‘pcl816_ai_cmd’:
drivers/staging/comedi/drivers/pcl816.c:629: error: ‘DMA_MODE_READ’ undeclared (first use in this function)
drivers/staging/comedi/drivers/pcl816.c:631: error: implicit declaration of function ‘clear_dma_ff’
drivers/staging/comedi/drivers/pcl816.c: In function ‘pcl816_ai_poll’:
drivers/staging/comedi/drivers/pcl816.c:679: error: implicit declaration of function ‘get_dma_residue’
make[2]: *** [drivers/staging/comedi/drivers/pcl816.o] Error 1
  CC [M]  drivers/staging/comedi/drivers/pcl818.o
drivers/staging/comedi/drivers/pcl818.c: In function ‘interrupt_pcl818_ai_mode13_dma’:
drivers/staging/comedi/drivers/pcl818.c:547: error: implicit declaration of function ‘disable_dma’
drivers/staging/comedi/drivers/pcl818.c:550: error: implicit declaration of function ‘set_dma_mode’
drivers/staging/comedi/drivers/pcl818.c:550: error: ‘DMA_MODE_READ’ undeclared (first use in this function)
drivers/staging/comedi/drivers/pcl818.c:550: error: (Each undeclared identifier is reported only once
drivers/staging/comedi/drivers/pcl818.c:550: error: for each function it appears in.)
drivers/staging/comedi/drivers/pcl818.c:551: error: implicit declaration of function ‘claim_dma_lock’
drivers/staging/comedi/drivers/pcl818.c:552: error: implicit declaration of function ‘set_dma_addr’
drivers/staging/comedi/drivers/pcl818.c:555: error: implicit declaration of function ‘set_dma_count’
drivers/staging/comedi/drivers/pcl818.c:561: error: implicit declaration of function ‘release_dma_lock’
drivers/staging/comedi/drivers/pcl818.c:562: error: implicit declaration of function ‘enable_dma’
drivers/staging/comedi/drivers/pcl818.c: In function ‘pcl818_ai_mode13dma_int’:
drivers/staging/comedi/drivers/pcl818.c:886: error: ‘DMA_MODE_READ’ undeclared (first use in this function)
drivers/staging/comedi/drivers/pcl818.c:888: error: implicit declaration of function ‘clear_dma_ff’
make[2]: *** [drivers/staging/comedi/drivers/pcl818.o] Error 1
  CC [M]  drivers/staging/comedi/drivers/das16.o
drivers/staging/comedi/drivers/das16.c: In function ‘das16_cmd_exec’:
drivers/staging/comedi/drivers/das16.c:644: error: implicit declaration of function ‘claim_dma_lock’
drivers/staging/comedi/drivers/das16.c:645: error: implicit declaration of function ‘disable_dma’
drivers/staging/comedi/drivers/das16.c:648: error: implicit declaration of function ‘clear_dma_ff’
drivers/staging/comedi/drivers/das16.c:650: error: implicit declaration of function ‘set_dma_addr’
drivers/staging/comedi/drivers/das16.c:654: error: implicit declaration of function ‘set_dma_count’
drivers/staging/comedi/drivers/das16.c:655: error: implicit declaration of function ‘enable_dma’
drivers/staging/comedi/drivers/das16.c:656: error: implicit declaration of function ‘release_dma_lock’
drivers/staging/comedi/drivers/das16.c: In function ‘disable_dma_on_even’:
drivers/staging/comedi/drivers/das16.c:845: error: implicit declaration of function ‘get_dma_residue’
drivers/staging/comedi/drivers/das16.c: In function ‘das16_attach’:
drivers/staging/comedi/drivers/das16.c:1197: error: implicit declaration of function ‘set_dma_mode’
drivers/staging/comedi/drivers/das16.c:1197: error: ‘DMA_MODE_READ’ undeclared (first use in this function)
drivers/staging/comedi/drivers/das16.c:1197: error: (Each undeclared identifier is reported only once
drivers/staging/comedi/drivers/das16.c:1197: error: for each function it appears in.)
make[2]: *** [drivers/staging/comedi/drivers/das16.o] Error 1
  CC [M]  drivers/staging/comedi/drivers/das1800.o
drivers/staging/comedi/drivers/das1800.c: In function ‘das1800_flush_dma_channel’:
drivers/staging/comedi/drivers/das1800.c:555: error: implicit declaration of function ‘disable_dma’
drivers/staging/comedi/drivers/das1800.c:559: error: implicit declaration of function ‘clear_dma_ff’
drivers/staging/comedi/drivers/das1800.c:562: error: implicit declaration of function ‘get_dma_residue’
drivers/staging/comedi/drivers/das1800.c: In function ‘das1800_flush_dma’:
drivers/staging/comedi/drivers/das1800.c:586: error: implicit declaration of function ‘claim_dma_lock’
drivers/staging/comedi/drivers/das1800.c:603: error: implicit declaration of function ‘release_dma_lock’
drivers/staging/comedi/drivers/das1800.c: In function ‘das1800_handle_dma’:
drivers/staging/comedi/drivers/das1800.c:622: error: implicit declaration of function ‘set_dma_addr’
drivers/staging/comedi/drivers/das1800.c:624: error: implicit declaration of function ‘set_dma_count’
drivers/staging/comedi/drivers/das1800.c:625: error: implicit declaration of function ‘enable_dma’
drivers/staging/comedi/drivers/das1800.c: In function ‘das1800_init_dma’:
drivers/staging/comedi/drivers/das1800.c:1424: error: implicit declaration of function ‘set_dma_mode’
drivers/staging/comedi/drivers/das1800.c:1424: error: ‘DMA_MODE_READ’ undeclared (first use in this function)
drivers/staging/comedi/drivers/das1800.c:1424: error: (Each undeclared identifier is reported only once
drivers/staging/comedi/drivers/das1800.c:1424: error: for each function it appears in.)
make[2]: *** [drivers/staging/comedi/drivers/das1800.o] Error 1
  CC [M]  drivers/staging/comedi/drivers/dt282x.o
drivers/staging/comedi/drivers/dt282x.c: In function ‘dt282x_ao_dma_interrupt’:
drivers/staging/comedi/drivers/dt282x.c:328: error: implicit declaration of function ‘disable_dma’
drivers/staging/comedi/drivers/dt282x.c: In function ‘prep_ai_dma’:
drivers/staging/comedi/drivers/dt282x.c:416: error: implicit declaration of function ‘set_dma_mode’
drivers/staging/comedi/drivers/dt282x.c:416: error: ‘DMA_MODE_READ’ undeclared (first use in this function)
drivers/staging/comedi/drivers/dt282x.c:416: error: (Each undeclared identifier is reported only once
drivers/staging/comedi/drivers/dt282x.c:416: error: for each function it appears in.)
drivers/staging/comedi/drivers/dt282x.c:417: error: implicit declaration of function ‘claim_dma_lock’
drivers/staging/comedi/drivers/dt282x.c:418: error: implicit declaration of function ‘clear_dma_ff’
drivers/staging/comedi/drivers/dt282x.c:419: error: implicit declaration of function ‘set_dma_addr’
drivers/staging/comedi/drivers/dt282x.c:420: error: implicit declaration of function ‘set_dma_count’
drivers/staging/comedi/drivers/dt282x.c:421: error: implicit declaration of function ‘release_dma_lock’
drivers/staging/comedi/drivers/dt282x.c:423: error: implicit declaration of function ‘enable_dma’
drivers/staging/comedi/drivers/dt282x.c: In function ‘prep_ao_dma’:
drivers/staging/comedi/drivers/dt282x.c:439: error: ‘DMA_MODE_WRITE’ undeclared (first use in this function)
drivers/staging/comedi/drivers/dt282x.c: In function ‘dt282x_interrupt’:
drivers/staging/comedi/drivers/dt282x.c:471: error: ‘DMA_MODE_READ’ undeclared (first use in this function)
drivers/staging/comedi/drivers/dt282x.c: In function ‘dt282x_ai_cmd’:
drivers/staging/comedi/drivers/dt282x.c:690: error: ‘DMA_MODE_READ’ undeclared (first use in this function)
drivers/staging/comedi/drivers/dt282x.c: In function ‘dt282x_ao_cmd’:
drivers/staging/comedi/drivers/dt282x.c:938: error: ‘DMA_MODE_WRITE’ undeclared (first use in this function)
make[2]: *** [drivers/staging/comedi/drivers/dt282x.o] Error 1
  CC [M]  drivers/staging/comedi/drivers/ni_at_a2150.o
drivers/staging/comedi/drivers/ni_at_a2150.c: In function ‘a2150_interrupt’:
drivers/staging/comedi/drivers/ni_at_a2150.c:237: error: implicit declaration of function ‘claim_dma_lock’
drivers/staging/comedi/drivers/ni_at_a2150.c:238: error: implicit declaration of function ‘disable_dma’
drivers/staging/comedi/drivers/ni_at_a2150.c:241: error: implicit declaration of function ‘clear_dma_ff’
drivers/staging/comedi/drivers/ni_at_a2150.c:249: error: implicit declaration of function ‘get_dma_residue’
drivers/staging/comedi/drivers/ni_at_a2150.c:286: error: implicit declaration of function ‘set_dma_addr’
drivers/staging/comedi/drivers/ni_at_a2150.c:287: error: implicit declaration of function ‘set_dma_count’
drivers/staging/comedi/drivers/ni_at_a2150.c:288: error: implicit declaration of function ‘enable_dma’
drivers/staging/comedi/drivers/ni_at_a2150.c:290: error: implicit declaration of function ‘release_dma_lock’
drivers/staging/comedi/drivers/ni_at_a2150.c: In function ‘a2150_attach’:
drivers/staging/comedi/drivers/ni_at_a2150.c:794: error: implicit declaration of function ‘set_dma_mode’
drivers/staging/comedi/drivers/ni_at_a2150.c:794: error: ‘DMA_MODE_READ’ undeclared (first use in this function)
drivers/staging/comedi/drivers/ni_at_a2150.c:794: error: (Each undeclared identifier is reported only once
drivers/staging/comedi/drivers/ni_at_a2150.c:794: error: for each function it appears in.)
make[2]: *** [drivers/staging/comedi/drivers/ni_at_a2150.o] Error 1

Make PCL816, PCL818, DAS16, DAS1800, DT282X, and NI_AT_A2150 depend on
ISA_DMA_API to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The comedi core module optionally allocates some legacy board minor
devices on module load and cleans these up on module exit.  These are
used for manual configuration of comedi boards (for those low-level
comedi drivers that support manual configuration - mainly for ISA
boards).  Other board minor devices are created and destroyed
dynamically in response to bus device probe and remove requests.  The
ioctl used for manual configuration (attachment) and removal
(detachment) of devices is COMEDI_DEVCONFIG, but that works for any
board minor device, including those that were originally created
dynamically.

If the COMEDI_DEVCONFIG ioctl is used to manually detach an
automatically created and attached device, commit
7d3135af ("staging: comedi: prevent
auto-unconfig of manually configured devices") ensures that the board
minor will no longer be automatically detached and destroyed by a bus
device remove request.  From that point on the board minor behaves more
like one of the comedi "legacy" board minors.  (There would be some
justification for destroying the board minor instead, but I'd rather
leave that decision until removal of board minors has been
made safer than it currently is.)  Although the board minor behaves more
like a legacy board minor, it is not currently cleaned up on module
exit.  In fact, the module exit code will bug out because this board
minor has not been cleaned up.

Change comedi_cleanup_legacy_minors() (called from the module exit code,
and from the module init code on error) to clean up all board minors.
Rename the function to comedi_cleanup_board_minors() to reflect the
change in functionality.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Comedi has two sorts of minor devices:
(a) normal board minor devices in the range 0 to
COMEDI_NUM_BOARD_MINORS-1 inclusive; and
(b) special subdevice minor devices in the range COMEDI_NUM_BOARD_MINORS
upwards that are used to open the same underlying comedi device as the
normal board minor devices, but with non-default read and write
subdevices for asynchronous commands.

The special subdevice minor devices get created when a board supporting
asynchronous commands is attached to a normal board minor device, and
destroyed when the board is detached from the normal board minor device.
One way to attach or detach a board is by using the COMEDI_DEVCONFIG
ioctl.  This should only be used on normal board minors as the special
subdevice minors are too ephemeral.  In particular, the change
introduced in commit 7d3135af ("staging:
comedi: prevent auto-unconfig of manually configured devices") breaks
horribly for special subdevice minor devices.

Since there's no legitimate use for the COMEDI_DEVCONFIG ioctl on a
special subdevice minor device node, disallow it and return -ENOTTY.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Reported-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

FWSERIAL_TTY_START_MINOR was removed. The minor_start is allocated
by tty_alloc_driver().
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use tty_alloc_driver() instead.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add the following file hierarchy to debugfs:

  <debugfs>-+
            +- firewire_serial -+- <unit> -+- peers
                                |          +- stats
                                |
                                +- <unit> -+- peers
                                           +- stats

The 'peers' file (read-only) contains status and configuration
info for attached peers for the given fwserial unit.

The 'stats' file (read-only) contains statistics and data profiling
information for each tty port for the given fwserial unit.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Factor out extra stats, data profiles, debugging info and peer info
from procfs file in preparation for using debugfs instead.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Register a second tty driver to create loopback devices for
each firewire node. Note that the loopback devices are numbered
from 0; the tty->index is transformed when used to index the
port table.

Remove the hack that previously enabled this.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Reported-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

After sending the unplug response, release the port even if an
error occurred.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>