- 06 Apr, 2016 5 commits
-
-
Stefan Assmann authored
Calling dev_close() causes IFF_UP to be cleared which will remove the interfaces routes and some addresses. That's probably not what the user intended when running the offline selftest. Besides this does not happen if the interface is brought down before the test, so the current behaviour is inconsistent. Instead call the net_device_ops ndo_stop function directly and avoid touching IFF_UP at all. Signed-off-by:
Stefan Assmann <sassmann@kpanic.de> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Doron Shikmoni authored
Garbled output for "ethtool -m ethX", in igb-driven NICs with module / plugin EEPROM (i.e. SFP information). Each output data byte appears duplicated. In igb_ethtool.c, igb_get_module_eeprom() is reading the EEPROM via i2c; the eeprom offset for each word that's read via igb_read_phy_reg_i2c() was passed in #words, whereas it needs to be a byte offset. This patches fixes the bug. Signed-off-by:
Doron Shikmoni <doron.shikmoni@gmail.com> Tested-by:
-
John Holland authored
The Intel i211 LOM PCIe Ethernet controllers' iNVM operates as an OTP and has no external EEPROM interface [1]. The following allows the driver to pickup the MAC address from a device tree blob when CONFIG_OF has been enabled. [1] http://www.intel.com/content/www/us/en/embedded/products/networking/i211-ethernet-controller-datasheet.htmlSigned-off-by:
John Holland <jotihojr@gmail.com> Tested-by:
-
Alexander Duyck authored
This patch enables bulk free in Tx cleanup for igb and cleans up the boolean logic in the polling routines for igb in the hopes of avoiding any mix-ups similar to what occurred with i40e and i40evf. Signed-off-by:
Alexander Duyck <aduyck@mirantis.com> Tested-by:
-
Alexander Duyck authored
We were casting the addr as __beXX and then passing it into le32_to_cpu because the device expects the MAC address to be in network order even though the register set is little endian. Instead of casting it as __beXX we can just cast it as __leXX in order to maintain consistency since the region of memory is already in little endian order as far as we are concerned. Signed-off-by:
-
- 05 Apr, 2016 35 commits
-
-
Aaron Conole authored
When signaling that a GRO frame is ready to be processed, the network stack correctly checks length and aborts processing when a frame is less than 14 bytes. However, such a condition is really indicative of a broken driver, and should be loudly signaled, rather than silently dropped as the case is today. Convert the condition to use net_warn_ratelimited() to ensure the stack loudly complains about such broken drivers. Signed-off-by:
Aaron Conole <aconole@bytheb.org> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Thomas Falcon authored
Enable RX Checksum offload feature in the ibmvnic driver. Signed-off-by:
Thomas Falcon <tlfalcon@linux.vnet.ibm.com> Cc: John Allen <jallen@linux.vnet.ibm.com> Signed-off-by:
-
Thomas Falcon authored
Allow the VNIC driver to provide descriptors containing L2/L3/L4 headers to firmware. This feature is needed for greater hardware compatibility and enablement of checksum and TCP offloading features. A new function is included for the hypervisor call, H_SEND_SUBCRQ_INDIRECT, allowing a DMA-mapped array of SCRQ descriptor elements to be sent to the VNIC server. These additions will help fully enable checksum offloading as well as other features as they are included later. Signed-off-by:
-
David S. Miller authored
Petri Gynther says: ==================== bcmgenet cleanups Three cleanup patches for bcmgenet. ==================== Signed-off-by: -
Petri Gynther authored
dmadesc_set() is used for setting the Tx buffer DMA address, length, and status bits on a Tx ring descriptor when a frame is being Tx'ed. Always set the Tx buffer DMA address first, before updating the length and status bits, i.e. giving the Tx descriptor to the hardware. The reason this is a cleanup rather than a fix is that the hardware won't transmit anything from a Tx ring until the TDMA producer index has been incremented. As long as the dmadesc_set() writes complete before the TDMA producer index write, life is good. Signed-off-by:
Petri Gynther <pgynther@google.com> Acked-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Petri Gynther authored
Add frag_size = skb_frag_size(frag) and use it when needed. Signed-off-by:
-
Petri Gynther authored
1. Readability: Move nr_frags assignment a few lines down in order to bundle index -> ring -> txq calculations together. 2. Readability: Add parentheses around nr_frags + 1. 3. Minor fix: Stop the Tx queue and throw the error message only if the Tx queue hasn't already been stopped. Signed-off-by:
-
David S. Miller authored
Willem de Bruijn says: ==================== udp: support SO_PEEK_OFF Support peeking at a non-zero offset for UDP sockets. Match the existing behavior on Unix datagram sockets. 1/3 makes the sk_peek_offset functions safe to use outside locks 2/3 removes udp headers before enqueue, to simplify offset arithmetic 3/3 introduces SO_PEEK_OFFSET support, with Unix socket peek semantics. Changes v1->v2 - squash patches 3 and 4 ==================== Signed-off-by: -
samanthakumar authored
Enable peeking at UDP datagrams at the offset specified with socket option SOL_SOCKET/SO_PEEK_OFF. Peek at any datagram in the queue, up to the end of the given datagram. Implement the SO_PEEK_OFF semantics introduced in commit ef64a54f ("sock: Introduce the SO_PEEK_OFF sock option"). Increase the offset on peek, decrease it on regular reads. When peeking, always checksum the packet immediately, to avoid recomputation on subsequent peeks and final read. The socket lock is not held for the duration of udp_recvmsg, so peek and read operations can run concurrently. Only the last store to sk_peek_off is preserved. Signed-off-by:
Sam Kumar <samanthakumar@google.com> Signed-off-by:
Willem de Bruijn <willemb@google.com> Signed-off-by:
-
samanthakumar authored
Remove UDP transport headers before queueing packets for reception. This change simplifies a follow-up patch to add MSG_PEEK support. Signed-off-by:
-
Willem de Bruijn authored
Make the peek offset interface safe to use in lockless environments. Use READ_ONCE and WRITE_ONCE to avoid race conditions between testing and updating the peek offset. Suggested-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queueDavid S. Miller authored
Jeff Kirsher says: ==================== 40GbE Intel Wired LAN Driver Updates 2016-04-05 This series contains updates to i40e and i40evf only. Stefan converts dev_close() to ndo_stop() for ethtool offline self test, since dev_close() causes IFF_UP to be cleared which will remove the interface routes and addresses. Alex bumps up the size of the transmit data buffer to 12K rather than 8K, which provides a gain in throughput and a reduction in overhead for putting together the frame. Fixed an issue in the polling routines where we were using bitwise operators to avoid the side effects of the logical operators. Then added support for bulk transmit clean for skbs. Jesse fixed a sparse issue in the type casting in the transmit code and fixed i40e_aq_set_phy_debug() to use i40e_status as a return code. Catherine cleans up duplicated code. Shannon fixed the cleaning up of the interrupt handling to clean up the IRQs only if we actually got them set up. Also fixed up the error scenarios where we were trying to remove a non-existent timer or worktask, which causes the kernel heartburn. Mitch changes the notification of resets to the reset interrupt handler, instead of the actual reset initiation code. This allows the VFs to get properly notified for all resets, including resets initiated by different PFs on the same physical device. Also moved the clearing of VFLR bit after reset processing, instead of before which could lead to double resets on VF init. Fixed code comment to match the actual function name. ==================== Signed-off-by: -
David S. Miller authored
Michael Chan says: ==================== bnxt_en: Updates for net-next. Update to latest firmware interface, add EEE feature, unsupported SFP+ module warning, and ethtool -s improvements. v2: Removed the GEEPROM patch and added more comments to the get_eee patch. ====================
-
Michael Chan authored
If autoneg is off, we should always report the speed and duplex settings even if it is link down so the user knows the current settings. The unknown speed and duplex should only be used for autoneg when link is down. Signed-off-by:
Michael Chan <michael.chan@broadcom.com> Signed-off-by:
-
Michael Chan authored
Check that the forced speed is a valid speed supported by firmware. If not supported, return -EINVAL. Signed-off-by:
-
Michael Chan authored
Add the PORT_CONN_NOT_ALLOWED async event handling logic. The driver will print an appropriate warning to reflect the SFP+ module enforcement policy done in the firmware. Signed-off-by:
-
Michael Chan authored
Currently, the driver only sets bit 0 of the async_event_fwd fields. To be compatible with the latest spec, we need to set the appropriate event bits handled by the driver. We should be handling link change and PF driver unload events, so these 2 bits should be set. Signed-off-by:
-
Michael Chan authored
Allow users to get|set EEE parameters. v2: Added comment for preserving the tx_lpi_timer value in get_eee. Signed-off-by:
-
Michael Chan authored
1. Add bnxt_hwrm_set_eee() function to setup EEE firmware parameters based on the bp->eee settings. 2. The new function bnxt_eee_config_ok() will check if EEE parameters need to be modified due to autoneg changes. 3. bnxt_hwrm_set_link() has added a new parameter to update EEE. If the parameter is set, it will call bnxt_hwrm_set_eee(). Signed-off-by:
-
Michael Chan authored
Get EEE capability and the initial EEE settings from firmware. Add "EEE is active | not active" to link up dmesg. Signed-off-by:
-
Michael Chan authored
Make use of the new AUTONEG_PAUSE bit in the new interface to better control autoneg flow control settings, independent of RX and TX advertisement settings. Signed-off-by:
-
Michael Chan authored
Use new field names in API structs and stop using deprecated fields auto_link_speed and auto_duplex in phy_cfg/phy_qcfg structs. Update copyright year to 2016. Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queueDavid S. Miller authored
Jeff Kirsher says: ==================== 100GbE Intel Wired LAN Driver Updates 2016-04-05 This series contains updates to fm10k only. Bruce provides nearly half of the patches in the series, most of which do general cleanup of the driver. These include semantic cleanups, checkpatch.pl fixes, update driver to use BIT() kernel macro, use BUILD_BUG_ON() where appropriate and use ether_addr_copy() instead of memcpy(). Jake provides the remaining patches in the series, starting with a fix for a possible NULL pointer deference. Next delays initialization of the service timer and service task until late in probe(). If we do not wait, failures in probe do not properly cleanup the service timer or service task items which result in a kernel panic. Added better reporting during error conditions. Fixed another possible kernel panic where we were clearing the interrupt scheme before we freed the mailbox IRQ. Added helper functions for setting strings and data for ethtool stats. Fixed comment mis-spelled words. v2: Dropped patch 3 from the original submission, until a better solution can be worked up based on feedback from Joe Perches and David Miller. ==================== Signed-off-by: -
Jacob Keller authored
The fm10k driver used its own code for generating a default indirection table on device load, which was not the same as the default generated by ethtool when indir_size of 0 is passed to SRXFH. Take advantage of ethtool_rxfh_indir_default() and simplify code to write the redirection table to reduce some code duplication. Signed-off-by:
Jacob Keller <jacob.e.keller@intel.com> Tested-by:
Krishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by:
-
Jacob Keller authored
s/funciton/function to resolve a typo, and cleanup grammar on a few comments regarding processing the VF mailboxes. Signed-off-by:
-
Jacob Keller authored
Fix a kernel panic that occurs during surprise removal. Clear the interface queue counts upon fm10k_init_msix_capability failure. This prevents further code (fm10k_update_stats etc.) from attempting to access unallocated queue vector or ring memory. [ 628.692648] BUG: unable to handle kernel NULL pointer dereference at 0000000000000068 [ 628.692805] IP: [<ffffffffa0475caf>] fm10k_update_stats+0x7f/0x2c0 [fm10k] [ 628.693173] PGD 0 [ 628.693759] Oops: 0000 [#1] SMP [ 628.699321] CPU: 10 PID: 8164 Comm: kworker/10:0 Tainted: G OE ------------ 3.10.0-327.el7.x86_64 #1 [ 628.700096] Hardware name: Supermicro X9DAi/X9DAi, BIOS 3.2 05/09/2015 [ 628.700894] Workqueue: pciehp-1 pciehp_power_thread [ 628.701686] task: ffff88086559c500 ti: ffff8808593c0000 task.ti: ffff8808593c0000 [ 628.702493] RIP: 0010:[<ffffffffa0475caf>] [<ffffffffa0475caf>] fm10k_update_stats+0x7f/0x2c0 [fm10k] [ 628.703310] RSP: 0018:ffff8808593c3b00 EFLAGS: 00010282 [ 628.704132] RAX: 0000000000000000 RBX: ffff880860760000 RCX: 0000000000000000 [ 628.704963] RDX: ffff880860760b08 RSI: 0000000000000000 RDI: 0000000000000000 [ 628.705794] RBP: ffff8808593c3b40 R08: 0000000000000000 R09: 0000000000000000 [ 628.706604] R10: 0000000000000000 R11: ffff880860760c40 R12: 0000000000000080 [ 628.707420] R13: ffff8808607608c0 R14: ffff880860779ec0 R15: ffff880860779f40 [ 628.708238] FS: 0000000000000000(0000) GS:ffff88086f000000(0000) knlGS:0000000000000000 [ 628.709071] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 628.709923] CR2: 0000000000000068 CR3: 000000000194a000 CR4: 00000000001407e0 [ 628.710752] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 628.711596] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 [ 628.712438] Stack: [ 628.713255] ffff880860764458 ffff8808607608c0 ffff880860760000 ffff880860760000 [ 628.714088] 0000000000000080 ffff8808607608c0 ffff880860779ec0 ffff880860779f40 [ 628.714925] ffff8808593c3b88 ffffffffa04780c5 ffff880860764458 0000000a8163cb5b [ 628.715752] Call Trace: [ 628.716560] [<ffffffffa04780c5>] fm10k_down+0x155/0x1f0 [fm10k] [ 628.717367] [<ffffffffa0479958>] fm10k_close+0x28/0xd0 [fm10k] [ 628.718184] [<ffffffff81526365>] __dev_close_many+0x85/0xd0 [ 628.718986] [<ffffffff815264d8>] dev_close_many+0x98/0x120 [ 628.719764] [<ffffffff81527ab8>] rollback_registered_many+0xa8/0x230 [ 628.720527] [<ffffffff81527c80>] rollback_registered+0x40/0x70 [ 628.721294] [<ffffffff81529198>] unregister_netdevice_queue+0x48/0x80 [ 628.722052] [<ffffffff815291ec>] unregister_netdev+0x1c/0x30 [ 628.722816] [<ffffffffa04762b8>] fm10k_remove+0xd8/0xe0 [fm10k] [ 628.723581] [<ffffffff81328c7b>] pci_device_remove+0x3b/0xb0 [ 628.724340] [<ffffffff813f5fbf>] __device_release_driver+0x7f/0xf0 [ 628.725088] [<ffffffff813f6053>] device_release_driver+0x23/0x30 [ 628.725814] [<ffffffff81321fe4>] pci_stop_bus_device+0x94/0xa0 [ 628.726535] [<ffffffff813220d2>] pci_stop_and_remove_bus_device+0x12/0x20 [ 628.727249] [<ffffffff8133de40>] pciehp_unconfigure_device+0xb0/0x1b0 [ 628.727964] [<ffffffff8133d822>] pciehp_disable_slot+0x52/0xd0 [ 628.728664] [<ffffffff8133d98a>] pciehp_power_thread+0xea/0x150 [ 628.729358] [<ffffffff8109d5fb>] process_one_work+0x17b/0x470 [ 628.730036] [<ffffffff8109e3cb>] worker_thread+0x11b/0x400 [ 628.730730] [<ffffffff8109e2b0>] ? rescuer_thread+0x400/0x400 [ 628.731385] [<ffffffff810a5aef>] kthread+0xcf/0xe0 [ 628.732036] [<ffffffff810a5a20>] ? kthread_create_on_node+0x140/0x140 [ 628.732674] [<ffffffff81645858>] ret_from_fork+0x58/0x90 [ 628.733289] [<ffffffff810a5a20>] ? kthread_create_on_node+0x140/0x140 [ 628.733883] Code: 83 e8 01 48 8d 97 40 02 00 00 45 31 c0 4c 8d 9c c7 48 02 0 [ 628.735202] RIP [<ffffffffa0475caf>] fm10k_update_stats+0x7f/0x2c0 [fm10k] [ 628.735732] RSP <ffff8808593c3b00> [ 628.736285] CR2: 0000000000000068 [ 628.736846] ---[ end trace 9156088b311aff42 ]--- Signed-off-by:
-
Bruce Allan authored
If 'attr_flag < (1 << (2 * FM10K_TEST_MSG_NESTED))' is ever false, err will be used uninitialized. Signed-off-by:
Bruce Allan <bruce.w.allan@intel.com> Tested-by:
-
Jacob Keller authored
Reduce duplicate code and the amount of indentation by adding fm10k_add_stat_strings and fm10k_add_ethtool_stats functions which help add fm10k_stat structures to the ethtool stats callbacks. This helps increase ease of use for future stat additions, and increases code readability. Skip handling of the per-queue stats as these will be reworked in a following patch. Signed-off-by:
-
Jacob Keller authored
During fm10k_io_error_detected we were clearing the interrupt scheme before we freed the MBX IRQ. This causes a kernel panic because the MBX IRQ are assigned after MSI-X initialization. Clearing the interrupt scheme results in removing the MSI-X entry table. Fix this by freeing the MBX IRQ before we clear the interrupt scheme, as we do elsewhere in the driver. Signed-off-by:
-
Jacob Keller authored
fm10k_stop_hw_generic calls fm10k_disable_queues_generic, which may return an error code indicating that the queues were not stopped within the time limit. Notify the user by displaying a message in the kernel message ring, in a similar way to how we notify the user when reset_hw fails. There isn't much we can do to recover from this error, so currently nothing else is done. Signed-off-by:
-
Jacob Keller authored
In fm10k_set_num_queues, we previously assigned the base template. This would always be overwritten by either fm10k_set_qos_queues or fm10k_set_rss_queues. In either case, we don't need the base values, so we can just remove them. Signed-off-by:
-
Jacob Keller authored
Delay initialization of the service timer and service task until late probe. If we don't wait, failures in probe do not properly cleanup the service timer or service task items, which results in the kernel panic below, potentially freezing the whole system. In addition, ensure that the SERVICE_DISABLE bit is set before we request the MBX IRQ since the MBX interrupt attempts to schedule the service task otherwise. This prevents a similar trace from occurring after this change. We didn't notice this issue before because probe almost always completes successfully. I discovered it due to a mis-ordered mailbox handler array, which resulted in the following failure when requesting mailbox interrupt. [ 555.325619] ------------[ cut here ]------------ [ 555.325628] WARNING: CPU: 0 PID: 4941 at lib/list_debug.c:33 __list_add+0xa0/0xd0() [ 555.325631] list_add corruption. prev->next should be next (ffffffff81f46648), but was (null). (prev=ffff8807fad5d0e8). <snip> [ 555.325722] CPU: 0 PID: 4941 Comm: insmod Tainted: G OE 4.0.4-303.fc22.x86_64 #1 [ 555.325725] Hardware name: Intel Corporation S2600CO/S2600CO, BIOS SE5C600.86B.02.03.8x23.060520140825 06/05/2014 [ 555.325727] 0000000000000000 00000000b4f161b3 ffff88081a21f8e8 ffffffff81783124 [ 555.325734] 0000000000000000 ffff88081a21f940 ffff88081a21f928 ffffffff8109c66a [ 555.325740] 0000000064000000 ffff8807fad5d0e8 ffff8807fad5d0e8 ffffffff81f46648 [ 555.325746] Call Trace: [ 555.325752] [<ffffffff81783124>] dump_stack+0x45/0x57 [ 555.325757] [<ffffffff8109c66a>] warn_slowpath_common+0x8a/0xc0 [ 555.325759] [<ffffffff8109c6f5>] warn_slowpath_fmt+0x55/0x70 [ 555.325763] [<ffffffff813ba270>] __list_add+0xa0/0xd0 [ 555.325768] [<ffffffff81102d1d>] __internal_add_timer+0x9d/0x110 [ 555.325771] [<ffffffff81102dbf>] internal_add_timer+0x2f/0xc0 [ 555.325774] [<ffffffff81104e5a>] mod_timer+0x12a/0x230 [ 555.325782] [<ffffffffa03d54ca>] fm10k_probe+0x69a/0xc80 [fm10k] [ 555.325787] [<ffffffff813e8355>] local_pci_probe+0x45/0xa0 [ 555.325791] [<ffffffff8129cf42>] ? sysfs_do_create_link_sd.isra.2+0x72/0xc0 [ 555.325794] [<ffffffff813e96b9>] pci_device_probe+0xf9/0x150 [ 555.325799] [<ffffffff814d7e73>] driver_probe_device+0xa3/0x400 [ 555.325802] [<ffffffff814d82ab>] __driver_attach+0x9b/0xa0 [ 555.325805] [<ffffffff814d8210>] ? __device_attach+0x40/0x40 [ 555.325808] [<ffffffff814d5bd3>] bus_for_each_dev+0x73/0xc0 [ 555.325811] [<ffffffff814d78ce>] driver_attach+0x1e/0x20 [ 555.325815] [<ffffffff814d7480>] bus_add_driver+0x180/0x250 [ 555.325819] [<ffffffffa03b2000>] ? 0xffffffffa03b2000 [ 555.325823] [<ffffffff814d8aa4>] driver_register+0x64/0xf0 [ 555.325826] [<ffffffff813e7bec>] __pci_register_driver+0x4c/0x50 [ 555.325832] [<ffffffffa03d6ca3>] fm10k_register_pci_driver+0x23/0x30 [fm10k] [ 555.325838] [<ffffffffa03b2080>] fm10k_init_module+0x80/0x1000 [fm10k] [ 555.325843] [<ffffffff81002128>] do_one_initcall+0xb8/0x200 [ 555.325848] [<ffffffff811e10d2>] ? __vunmap+0xa2/0x100 [ 555.325852] [<ffffffff811fe239>] ? kmem_cache_alloc_trace+0x1b9/0x240 [ 555.325855] [<ffffffff8178230e>] ? do_init_module+0x28/0x1cb [ 555.325858] [<ffffffff81782346>] do_init_module+0x60/0x1cb [ 555.325862] [<ffffffff8112168e>] load_module+0x205e/0x26b0 [ 555.325866] [<ffffffff8111d110>] ? store_uevent+0x70/0x70 [ 555.325870] [<ffffffff812234b0>] ? kernel_read+0x50/0x80 [ 555.325873] [<ffffffff81121f3e>] SyS_finit_module+0xbe/0xf0 [ 555.325878] [<ffffffff81789749>] system_call_fastpath+0x12/0x17 [ 555.325880] ---[ end trace 9e0f58d071eafd2a ]--- Signed-off-by:
-
Jacob Keller authored
According to the C standard dereferencing a variable before it is checked invokes undefined behavior, and thus compilers are free to assume the check for NULL isn't necessary. Prevent this by re-ordering the NULL check of msix_entries in fm10k_free_mbx_irq. Signed-off-by:
-
Bruce Allan authored
Cleanup the remaining instances of using memcpy() instead of the preferred ether_addr_copy(). Signed-off-by:
-
Bruce Allan authored
Signed-off-by:
-
