Fix Bug #677 - I/O errors on heavy microSD writes for 2.6.22.x.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

is stopped.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Harald Welte <laforge@openmoko.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Bugfix to ensure DMA channel allocated is freed on exit.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

This patch is a workaround of some S3C2410 MMC chip bug
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

This is the latest S3C MMC/SD driver by Thomas Kleffel
with cleanups as suggested by AKPM done by Ben Dooks.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Thomas Kleffel <tk@maintech.de>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Be a bit more robust and fall back to PIO if someone is feeding us
bogus addresses.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Clean up and reorganise the mmc_test driver so that it (hopefully)
is easier to extend with more complex tests.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Many failures are non-permanent, but the card might need some time to
finish what it is doing before becoming responsive again. Make sure we
wait for it to finish programming before dealing with the error.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Add support for the scatter-gather DMA mode present on newer controllers.
As the mode requires 32-bit alignment, non-aligned chunks are handled by
using a bounce buffer.

Also add some new quirks to handle controllers that have bugs in the
ADMA engine.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

The upcoming JMicron chips will have solved all the currently known
bugs, so don't penalize them for older problems.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

We can only perform the tests on MMC and SD cards, so avoid binding
to any other type.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Make sure that the maximum size for a byte mode transfer is identical
in all places. Also tweak the transfer helper so that a single byte
mode transfer is preferred over (possibly multiple) block mode
request(s).
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

There are a lot of crappy controllers out there that cannot handle
all the request sizes that the MMC/SD/SDIO specifications require.
In case the card driver can pad the data to overcome the problems,
this commit adds a helper that calculates how much that padding
should be.

A corresponding helper is also added for SDIO, but it can also deal
with all the complexities of splitting up a large transfer efficiently.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

The MMC core provides a carddetect poll feature, time to
remove the driver's own implementation of it.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Don't process an MMC request if no card is present.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Clean up the codebase, no functional changes.
- merge the au1xmmc.h header contents into the driver file,
- indentation, spelling and style fixes.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Wire up the SD controllers' SDIO IRQ capability.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Remove the DB1200 board-specific functions (card present, read-only,
activity LED methods) and instead add platform data which is passed
to the driver.  This also allows for platforms to implement other
carddetect schemes (e.g. dedicated irq) without having to pollute the
driver code.  The poll timer (used for pb1200) is kept for compatibility.

With the board-specific stuff gone, the driver's ->probe() code can be
cleaned up considerably.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

The byte mode support fails to clear the byte mode bit in the command
register, possibly leaving byte mode enabled with the counters programmed
in non-byte mode.
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

According to the documentation the AT91SAM9261 MCI shares the block size
limitations of the AT91RM9200 MCI. Also the errata documentation for
AT91RM9200 and AT91SAM9261 state that stream commands are not supported.
This has not been tested on actual hardware.
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

AT91SAM926[0/3] PDC must write at least 12 bytes. The code compiles and runs
but the actual condition for this erratum did not trigger in my tests so it's
unclear if it actually works as intended.
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

In at91_mci_completed_command() function, this patch distinguishes
command error and data error. It reports it in the corresponding
error field.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Reading AT91_MCI_SR again at the end of transfer can corrupt the
error reporting. Some fields in the SR register are read-and-clear.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Enable SDIO interrupt handling.
Signed-off-by: Eric Benard <ebenard@free.fr>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

at91_mci is capable of multiwrite. Enable it before it disappears.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Modify bytes_xfered value after a write.

That will report, as accurately as possible, the amount of
sectors that are effectively written.

This update introduces the check of the busy signal given by
the card.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

The at91 mci controller internal state machine seems to often crash. This can
be fixed by resetting the controller after each command for at91rm9200 and by
setting the MCI_BLKR register on at91sam926*.
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Hans J Koch <hjk@linutronix.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Detect command timeout (or mci controller hangs).
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Hans J Koch <hjk@linutronix.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Implement transfer with size not modulo 4 for at91sam9*. Please note that the
at91rm9200 simply can't handle this.
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Make the variable name in the comments match the actual name
of the variable.
Signed-off-by: Deepak Saxena <dsaxena@laptop.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Now get_ro() callback must return 0/1 values for its logical states, and
negative errno values in case of error. If particular host instance doesn't
support RO/WP switch, it should return -ENOSYS.

This patch changes some hosts in two ways:

1. Now functions should be smart to not return negative values in
   "RO asserted" case (particularly gpio_ calls could return negative
   values for the outermost GPIOs).

   Also, board code usually passes get_ro() callbacks that directly return
   gpioreg & bit result, so at91_mci, imxmmc, pxamci and mmc_spi's get_ro()
   handlers need take special care when returning platform's values to the
   mmc core.

2. In case of host instance didn't implement get_ro() callback, it should
   really return -ENOSYS and let the mmc core decide what to do about it
   (mmc core thinks the same way as the hosts, so it isn't functional
   change).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

This patch adds new platform data variable "caps", so platforms
could pass theirs capabilities into MMC core (for example, platforms
without interrupt on the CD line will most probably want to pass
MMC_CAP_NEEDS_POLL).

New platform get_cd() callback provided to optimize polling.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Some hosts (and boards that use mmc_spi) do not use interrupts on the CD
line, so they can't trigger mmc_detect_change. We want to poll the card
and see if there was a change. 1 second poll interval seems resonable.

This patch also implements .get_cd() host operation, that could be used
by the hosts that are able to report card-detect status without need to
talk MMC.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

This patch removes a CVS tag that wasn't updated for a long time.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

The Ricoh controllers cannot handle unaligned data blocks.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Add the ability to run just a single test case by writing the test
case number into the sysfs "test" file.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Gracefully handle when the device is suddenly removed. Do a test read
and avoid any further access if that read returns -1.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

JMicron chips sometimes have two interfaces to work around limitations
in Microsoft's sdhci driver. This patch allows us to use either interface.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>