Frames are not guaranteed to be 802.11 frames in
ath10k_htt_tx() and the tx completion handler.
In some cases, like TDLS, they can be Ethernet.
Hence checking, e.g. frame_control could yield
bogus results and behavior.

Fortunately this wasn't a real problem so far
because there's no FW/HW combination to encounter
this problem.

However it is good to fix this in advance.

Fixes: 75d85fd9 ("ath10k: introduce basic tdls functionality")
Fixes: eebc67fe ("ath10k: fix pmf for wmi-tlv on qca6174")
Fixes: 7b7da0a0 ("ath10k: drop probe responses when too many are queued")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

It was wasteful to have all the flags as separate
bools.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

It was wasteful to keep it in the struct.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

It was wasteful to keep it in the struct.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

It was wasteful to keep it in the struct because
it can be passed as function argument down the tx
path.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

All functions should have ath10k_{filename}_
prefixes.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

It was wasteful to have two flags describing
the same thing.

While at it fix code style of
ath10k_tx_h_use_hwcrypto().
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

The QCA99X0 4 addresses RX packets pad 2 bytes at the beginning of
MSDU instead the end of ieee80211 header to keep alignment. The currently RX
data path can't parse the header correctly in this case. This patch fixes it
for QCA99X0.
Signed-off-by: Yanbo Li <yanbol@qca.qualcomm.com>
[kvalo@qca.qualcomm.com: checkpatch fixes and naming changes]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

To prevent race when connect flow may run in parallel with
the disconnect event.

Scenario leading to the bug is: while running connect flow on the AP,
STA sends disconnect. log follows.

<7>[  668.736269] wil6210 0000:01:00.0: wlan0: DBG[ WMI]Configure for connection CID 1
<7>[  668.736269] wil6210 0000:01:00.0: wlan0: DBG[MISC]wil_vring_init_tx() max_mpdu_size 2048
<7>[  668.736301] wil6210 0000:01:00.0: wlan0: DBG[MISC]wil_vring_alloc()
<7>[  668.736363] wil6210 0000:01:00.0: wlan0: DBG[MISC]vring[1024] 0xffbe8000:d962ce08 0xdb244000
<7>[  668.736394] wil6210 0000:01:00.0: wlan0: DBG[ WMI]Head 0x00880300 -> 0x00880308
<7>[  668.736394] wil6210 0000:01:00.0: wlan0: DBG[ WMI]WMI command 0x0821 [28]
<7>[  668.736426] DBG[ WMI]Cmd 00000000: 20 00 24 00 00 00 00 00 00 00 21 08 00 00 00 00   .$.......!.....
<7>[  668.736426] DBG[ WMI]cmd 00000000: 00 00 00 00 00 00 5f 5c 00 00 00 00 00 04 00 08  ......_\........
<7>[  668.736457] DBG[ WMI]cmd 00000010: 01 01 00 00 00 00 00 00 00 00 ff 0f              ............
<7>[  668.736488] wil6210 0000:01:00.0: wlan0: DBG[ IRQ]Pseudo IRQ 0x00000004
<7>[  668.736519] wil6210 0000:01:00.0: wlan0: DBG[ WMI]Handle WMI 0x1824 (reply_id 0x1821)
<7>[  668.736519] wil6210 0000:01:00.0: wlan0: DBG[ IRQ]wil6210_mask_irq_pseudo()
<7>[  668.736519] wil6210 0000:01:00.0: wlan0: DBG[ IRQ]ISR MISC 0x20000000
<7>[  668.736551] wil6210 0000:01:00.0: wlan0: DBG[ WMI]Handle WMI 0x1003 (reply_id 0x1821)
<7>[  668.736551] wil6210 0000:01:00.0: wlan0: DBG[ WMI]Disconnect 04:ce:14:00:07:70 reason [proto 3 wmi 4]
<7>[  668.736582] wil6210 0000:01:00.0: wlan0: DBG[MISC]wil6210_disconnect()
<7>[  668.736613] wil6210 0000:01:00.0: wlan0: DBG[ IRQ]Thread IRQ
<7>[  668.736613] wil6210 0000:01:00.0: wlan0: DBG[ IRQ]Thread ISR MISC 0x20000000
<7>[  668.736644] wil6210 0000:01:00.0: wlan0: DBG[ IRQ]MBOX event
<7>[  668.736644] wil6210 0000:01:00.0: wlan0: DBG[ WMI]Mbox head 00880330 tail 00880328
<7>[  668.736676] wil6210 0000:01:00.0: wlan0: DBG[ WMI]Mbox evt 001a 0010 0000 00
<7>[  668.736676] wil6210 0000:01:00.0: wlan0: DBG[ WMI]WMI event 0x1821 MID 0 @3255145 msec
<7>[  668.736707] DBG[ WMI]evt 00000000: 1a 00 10 00 00 00 00 10 00 00 21 18 69 ab 31 00  ..........!.i.1.
<7>[  668.736707] DBG[ WMI]evt 00000010: 01 01 00 00 00 00 00 00                          ........
<7>[  668.736738] wil6210 0000:01:00.0: wlan0: DBG[ WMI]queue_work -> 0
<7>[  668.736738] wil6210 0000:01:00.0: wlan0: DBG[ WMI]wmi_recv_cmd -> 1 events queued
<7>[  668.736769] wil6210 0000:01:00.0: wlan0: DBG[ IRQ]wil6210_unmask_irq_pseudo()
<7>[  668.736832] wil6210 0000:01:00.0: wlan0: DBG[MISC]Disconnect 04:ce:14:00:07:70, CID=1, reason=3
<7>[  668.736832] wil6210 0000:01:00.0: wlan0: DBG[MISC]wil_disconnect_cid(CID 1, status 1)
<7>[  668.736894] wil6210 0000:01:00.0: wlan0: DBG[MISC]wil_vring_fini_tx() id=1
<7>[  668.736894] wil6210 0000:01:00.0: wlan0: DBG[MISC]free Tx vring 1 [1024] 0xffbe8000:d962ce08 0xdb244000
<7>[  668.736957] wil6210 0000:01:00.0: wlan0: DBG[ WMI]Handle WMI 0x1821 (reply_id 0x1821)
<7>[  668.736988] wil6210 0000:01:00.0: wlan0: DBG[ WMI]Complete WMI 0x1821
<7>[  668.737019] wil6210 0000:01:00.0: wlan0: DBG[ WMI]wmi_call(0x0821->0x1821) completed in 0 msec
<3>[  668.737019] wil6210 0000:01:00.0: wlan0: Tx config failed, status 0x01
<7>[  668.739518] wil6210 0000:01:00.0: wlan0: DBG[MISC]wil_cfg80211_del_station(04:ce:14:00:07:70, reason=2)
<7>[  668.739550] wil6210 0000:01:00.0: wlan0: DBG[MISC]wil6210_disconnect()
<7>[  668.739550] wil6210 0000:01:00.0: wlan0: DBG[MISC]_wil6210_disconnect(bssid=04:ce:14:00:07:70, reason=2, ev-)
<7>[  668.739581] wil6210 0000:01:00.0: wlan0: DBG[MISC]Disconnect 04:ce:14:00:07:70, CID=-2, reason=2
<7>[  668.742705] wil6210 0000:01:00.0: wlan0: DBG[MISC]free Tx vring 1 [1024] 0x  (null):d962ce08 0x  (null)
<3>[  668.742736] __dma_free_remap: trying to free invalid coherent area:   (null)
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

The RX rate idx is not correct for 11G mode OFDM packet.
Because the bitrate table start with CCK index instead of OFDM.
Signed-off-by: Yanbo Li <yanbol@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Of a word in struct htt_data_tx_desc htt version >= 3.4 firmware uses
LSB 16-bit for frequency configuration which is used for offchannel tx
and MSB 16-bit is for peerid. But other firmwares using version 2.X
(10.1, 10.2.2, 10.2.4 and 10.4) are using 32-bit for peerid in htt tx
desc. So far no issue is found with the existing code setting peerid and
freq for HTT version 2.X, this could be mainly because of 0 as frequecy
(home channel) is being always passed with those firmwares. There may be
issues when non-zero freq is passed with firmware using < 3.4 htt version.
To be safe use target_version_major and target_version_minor along with
htt-op-version before configuring peer id and freq in htt tx desc. This
patch extends ath10k_mac_tx_frm_has_freq() to check for htt_op_version_tlv
and uses the helper while setting peerid in htt_tx_desc.

Fixes: 8d6d3624 ("ath10k: fix offchan reliability")
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Rename ath10k_mac_need_offchan_tx_work() to ath10k_mac_tx_frm_has_freq()
to make it more meaningful. This helper will be used in the future
change. No functionality change.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

There is an extra 4-byte member when compared to WMI 10.2 added to
assoc complete command in WMI 10.4. This new member is used for 160Mhz
related configuration. This WMI command mismatch between host and
firmware does not cause any real issues because this new member is not
used in 10.4 firmwares so far (10.4.1.00030-1). This difference in WMI
command interface brings in a new wmi_ops for 10.4 gen_peer_assoc().
No noticeable functionality differences with this change can be seen
with the current 10.4 firmwares, but the WMI interface has to be
fixed to work with future 10.4 firmwares which may be using this new
member.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

As not all QCA98XX radios are not connected to Bluetooth modules, enabling the
BT coex feature in firmware will have side effects if the radio's GPIO are
connected with other (non-BT) HW modules. Add debugfs file to control the
firmware BT coex logic and set the feature as disable by default to avoid that
btcoex is accidentally enabled.

To enable this feature, execute:

echo 1 > /sys/kernel/debug/ieee80211/phyX/ath10k/btcoex

To disable:

echo 0 > /sys/kernel/debug/ieee80211/phyX/ath10k/btcoex

The firmware support this feature since 10.2.4.54 on 2G-only board, dual band
or 5G boards don't support this. The feature's name is WMI_SERVICE_COEX_GPIO
and the btcoex file is not created if firmware doesn't support it.
Signed-off-by: Yanbo Li <yanbol@qca.qualcomm.com>
[kvalo@qca.qualcomm.com: use btcoex filename and other smaller fixes]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This patch adds pktlog support for 10.4 fw versions.
Signed-off-by: Vivek Natarajan <nataraja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

No functionality change, just sync to the latest
pdev params that 10.4 firmware defines.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

No real functionality change, add WMI command/event
defines to be in sync with 10.4 firmware.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

No functional changes, adds new wmi service bits for
10.4 firmware to be sync with 10.4 firmware.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This patch enables thermal throttling support for 10.4 firmware.
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Set peer's management frame protection flag in peer assoc command,
this setting will enable/disable encrytion of management frames in fw.

Setting of this flag is based on whether MFP is enabled/disabled at STA
and a firmware feature flag ATH10K_FW_FEATURE_MFP_SUPPORT. This is because
only firmwares 10.1.561 and above have support for MFP.
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Manikanta pubbisetty <c_mpubbi@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Abstraction layer for peer flags is added to fix ABI breakage.
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: SenthilKumar Jegadeesan <sjegadee@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This patch replaces multiple if conditional checks with a single if condition
in WMI management rx handler. Found during code review.
Signed-off-by: Manikanta Pubbisetty <manikanta.pubbisetty@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This supports a way to get target stats through normal
ethtool stats API.

For instance:
# ethtool -S wlan1
NIC statistics:
     tx_pkts_nic: 353
     tx_bytes_nic: 25142
     rx_pkts_nic: 6
     rx_bytes_nic: 996
     d_tx_ucast_pkts: 89
     d_tx_bcast_pkts: 264
     d_tx_ucast_bytes: 3020
     d_tx_bcast_bytes: 22122
...
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This will allow us to call it from elsewhere when implementing
ethtool stats.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Improper use of strlcpy caused garbage to be appended to the
firmware version string.  Fix this by paying attention to the
ie_lenth.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

It can take a user a while to understand why their
NIC that advertises 802.11n support cannot actually
do 802.11n.  Print out a warning in the logs to save
the next poor person to use this NIC some trouble.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This lets 'iw phy phy0 info' report antennas for
the radio device:

...
	Available Antennas: TX 0x2 RX 0x2
	Configured Antennas: TX 0x2 RX 0x2
...
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

When configuring Tx vring for new connection,
WMI call to the firmware may fail. In this case, need to
clean up properly. In particular, need to call
cfg80211_del_sta() in case of AP like interface.

Perform full "disconnect" procedure for proper clean up
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Adjust driver behavior during FW boot. Proper sequence of
events after reset and FW download, is as following:

- FW prepares mailbox structure and reports IRQ "FW_READY"
- driver caches mailbox registers, marks mailbox readiness
- FW sends WMI_FW_READY event, ignore it
- FW sends WMI_READY event with some data
- driver stores relevant data marks FW is operational
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

When Tx ring full is encountered with TSO,
printout of "DMA error" was wrongly printed.

In addition, in case of Tx ring full return
proper error code so that NETDEV_TX_BUSY is
returned to network stack in order not to
drop the packets and retry transmission of the
packets when ring is emptied.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Some events are ignored for purpose; such events should not
be treated as "unhandled events". Replace info message
saying "unhandled" with debug one saying "ignore", to reduce
dmesg pollution
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Add the hardware name, revision and update the pci_id table.

Currently there're two HW ref. designs available I'm aware of,
with 1.0.2 and 1.1 chip revisions. I've access and been using
the first one so far and this patch cover only it.

QCA9377 inherits most of the stuff (e.g. fw interfaces)
from QCA61x4 design, so the integration was pretty straightforward.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

To reflect configured antenna settings in HT/VHT MCS map,
reload the HT/VHT capabilities upon antenna change.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Move HT and VHT capabiltity setup static functions to avoid
forward declaration.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

HT/VHT MCS rateset should be filled only for configured chainmask
rather that max supported chainmask. Fix that by checking configured
chainmask while filling HT/VHT MCS rate map.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Removing supported chainmask fields as it can be always derived
from num_rf_chains.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

For the messages from host to target, shadow copy of CE descriptors
are maintained in source ring. Before writing actual CE descriptor,
first shadow copy is filled and then it is copied to CE address space.
To optimize in download path and to reduce d-cache pressure, removing
shadow copy of CE descriptors. This will also reduce driver memory
consumption by 33KB during on device probing.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

The physical address necessary to unmap DMA ('bufferp') is stored
in ath10k_skb_cb as 'paddr'. ath10k doesn't rely on the meta/transfer_id
when handling send completion (htc ep id is stored in sk_buff control
buffer). So the unused output arguments {bufferp, nbytesp and transfer_idp}
are removed from CE send completion. This change is needed before removing
the shadow copy of copy engine (CE) descriptors in follow up patch.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

CE diag window access is serialized (it has to be by design) so
there's no way to get a different send completion. so there's no
need for post completion validation.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Currently to avoid uncached memory access while filling up copy engine
descriptors, shadow descriptors are used. This can be optimized further
by removing shadow descriptors. To achieve that first shadow ring
dependency in ce_send is removed by creating local copy of the
descriptor on stack and make a one-shot copy into the "uncached"
descriptor.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>